Search NASA⌕ Search

SEARCH · Search NASA

Results for “real time computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A real-time simulation evaluation of an advanced detection, isolation and accommodation algorithm for sensor failures in turbine engines

An advanced sensor failure detection, isolation, and accommodation (ADIA) algorithm has been developed for use with an aircraft turbofan engine control system. In a previous paper the authors described the ADIA algorithm and its real-time implementation. Subsequent improvements made to the algorithm and implementation are discussed, and the results of an evaluation presented. The evaluation used a real-time, hybrid computer simulation of an F100 turbofan engine.

Merrill, W. C.↗
NASA NTRS1987

Full-scale engine demonstration of an advanced sensor failure detection isolation, and accommodation algorithm - Preliminary results

The objective of the advanced detection, isolation, and accommodation (ADIA) program is to improve the overall demonstrated reliability of digital electronic control systems for turbine engines. For this purpose, algorithms were developed which detect, isolate, and accommodate sensor failures using analytical redundancy. Preliminary results of a full scale engine demonstration of the ADIA algorithm are presented. Minimum detectable levels of sensor failures for an F100 turbofan engine control system are determined and compared to those obtained during a previous evaluation of this algorithm using a real-time hybrid computer simulation of the engine.

Merrill, Walter C.↗
NASA NTRS1988

Intelligent test integration system

A new test technology is described which was developed for space system integration. The ultimate purpose of the system is to support the automatic generation of test systems in real time, distributed computing environments. The Intelligent Test Integration System (ITIS) is a knowledge based layer above the traditional test system components which can generate complex test configurations from the specification of test scenarios.

Sztipanovits, J.↗
NASA NTRS1988

OMV docking simulator

The Boeing Orbital Maneuvering Vehicle (OMV) Docking and Proximity Operation System (DAPOS) was completed. The system constructed involves the use of four separate processors. Appropriate software was developed that drives each of these four processors. The hand controller logic coordinates all the activities in the control station, and communicates with the OMV mathematical model. The state vector generated by the model is in turn transmitted to the control station as well as the POLY 2000 (via the ALCYON host computer) for real time graphics generation. The OMV characteristics are stored in a data file which may be easily updated and modified without disturbing the software, thereby making the system very flexible. The current system supports two types of hand controllers. The system was flown by several volunteers, some of whom are airplane pilots. A user manual is also enclosed.

Teoh, W.↗
NASA NTRS1987

Telepresence master glove controller for dexterous robotic end-effectors

This paper describes recent research in the Aerospace Human Factors Research Division at NASA's Ames Research Center to develop a glove-like, control and data-recording device (DataGlove) that records and transmits to a host computer in real time, and at appropriate resolution, a numeric data-record of a user's hand/finger shape and dynamics. System configuration and performance specifications are detailed, and current research is discussed investigating its applications in operator control of dexterous robotic end-effectors and for use as a human factors research tool in evaluation of operator hand function requirements and performance in other specialized task environments.

Fisher, Scott S.↗
NASA NTRS1987

Helicopter terminal approach using differential GPS with vertical-axis enhancement

The NAVSTAR Global Positioning System (GPS) in differential mode (DGPS) has been shown to be least accurate in the vertical axis. The vertical axis also has the most stringent accuracy requirements for aircraft precision approach and landing. A series of flight tests were conducted to evaluate a concept for improving the DGPS vertical axis navigation performance. These tests incorporated augmentation sensors to aid the DGPS navigation solution during terminal approach operations. A GPS receiver was installed on board a NASA helicopter and interfaced with a real-time digital computer system. A reconfigurable navigation filter programmed in the digital computer provided an augmented DGPS solution, with selectable inputs from a low-cost vertical accelerometer, a barometric altimeter, and the aircraft attitude gyros. The reference aircraft position was determined by a laser tracker. Extensive post-test analysis was done to optimize the filter performance during the terminal approach operation. Test results show that baro-altimeter aiding can significantly improve vertical axis performance. Follow-on tests are planned for the optimized configurations.

Edwards, F. G.↗
NASA NTRS1988

Advanced detection, isolation, and accommodation of sensor failures - Real-time evaluation

The objective of the Advanced Detection, Isolation, and Accommodation (ADIA) program is to improve the overall demonstrated reliability of digital electronic control systems for turbine engines by using analytical redundancy to detect sensor failures. The results of a real-time hybrid computer evaluation of the ADIA algorithm are presented. Minimum detectable levels of sensor failures for an F100 engine control system are determined. Also included are details about the microprocessor implementation of the algorithm as well as a description of the algorithm itself.

Merrill, Walter C.↗
NASA NTRS1989

Performance evaluation of a six-axis generalized force-reflecting teleoperator

Work in real-time distributed computation and control has culminated in a prototype force-reflecting telemanipulation system having a dissimilar master (cable-driven, force-reflecting hand controller) and a slave (PUMA 560 robot with custom controller), an extremely high sampling rate (1000 Hz), and a low loop computation delay (5 msec). In a series of experiments with this system and five trained test operators covering over 100 hours of teleoperation, performance was measured in a series of generic and application-driven tasks with and without force feedback, and with control shared between teleoperation and local sensor referenced control. Measurements defining task performance included 100-Hz recording of six-axis force/torque information from the slave manipulator wrist, task completion time, and visual observation of predefined task errors. The task consisted of high precision peg-in-hole insertion, electrical connectors, velcro attach-de-attach, and a twist-lock multi-pin connector. Each task was repeated three times under several operating conditions: normal bilateral telemanipulation, forward position control without force feedback, and shared control. In shared control, orientation was locally servo controlled to comply with applied torques, while translation was under operator control. All performance measures improved as capability was added along a spectrum of capabilities ranging from pure position control through force-reflecting teleoperation and shared control. Performance was optimal for the bare-handed operator.

Hannaford, B.↗
NASA NTRS1990

Measurement and analysis of workload effects on fault latency in real-time systems

The authors demonstrate the need to address fault latency in highly reliable real-time control computer systems. It is noted that the effectiveness of all known recovery mechanisms is greatly reduced in the presence of multiple latent faults. The presence of multiple latent faults increases the possibility of multiple errors, which could result in coverage failure. The authors present experimental evidence indicating that the duration of fault latency is dependent on workload. A synthetic workload generator is used to vary the workload, and a hardware fault injector is applied to inject transient faults of varying durations. This method makes it possible to derive the distribution of fault latency duration. Experimental results obtained from the fault-tolerant multiprocessor at the NASA Airlab are presented and discussed.

Woodbury, Michael H.↗
NASA NTRS1990

Defining, modeling, and measuring system lag in virtual environments

In such real-time interactive computer environments as those used for virtual environments and simulators, system lag dramatically affects system usability. Attention is presently given to two types of lag: (1) transmission lag time, which is the difference between the moving of a sensing device and that device's motion on a graphic display, and (2) position lag, which is the difference between the actual position of a tracker in motion and the displayed position of a tracker at the same time. A method for measuring these types of lag using a video technique was developed for the NASA-Ames Virtual Interactive Environment Workstation. The position lag can be understood in terms of the transmission lag, so that optimizing a system for small transmission lag will also optimize for small position lag.

Bryson, Steve↗
NASA NTRS1991

Performance evaluation of a six-axis generalized force-reflecting teleoperator

Work in real-time distributed computation and control has culminated in a prototype force-reflecting telemanipulation system having a dissimilar master (cable-driven force-reflecting hand controller) and a slave (PUMA 560 robot with custom controller), an extremely high sampling rate (1000 Hz), and a low loop computation delay (5 msec). In a series of experiments with this system and five trained test operators covering more than 100 hours of teleoperation, performance was measured in a series of generic and application-driven tasks with and without force feedback, and with control shared between teleoperation and local sensor referenced control. All performance measures improved as capability was added along a spectrum of capabilities ranging from pure position control through force-reflecting teleoperation and shared control. Performance was optimal for the bare-handed operator.

Hannaford, Blake↗
NASA NTRS1993

Advanced Launch System Multi-Path Redundant Avionics Architecture Analysis and Characterization

The objective of the Multi-Path Redundant Avionics Suite (MPRAS) program is the development of a set of avionic architectural modules which will be applicable to the family of launch vehicles required to support the Advanced Launch System (ALS). To enable ALS cost/performance requirements to be met, the MPRAS must support autonomy, maintenance, and testability capabilities which exceed those present in conventional launch vehicles. The multi-path redundant or fault tolerance characteristics of the MPRAS are necessary to offset a reduction in avionics reliability due to the increased complexity needed to support these new cost reduction and performance capabilities and to meet avionics reliability requirements which will provide cost-effective reductions in overall ALS recurring costs. A complex, real-time distributed computing system is needed to meet the ALS avionics system requirements. General Dynamics, Boeing Aerospace, and C.S. Draper Laboratory have proposed system architectures as candidates for the ALS MPRAS. The purpose of this document is to report the results of independent performance and reliability characterization and assessment analyses of each proposed candidate architecture and qualitative assessments of testability, maintainability, and fault tolerance mechanisms. These independent analyses were conducted as part of the MPRAS Part 2 program and were carried under NASA Langley Research Contract NAS1-17964, Task Assignment 28.

Baker, Robert L.↗
NASA NTRS1988

An adaptive identification and control scheme for large space structures

A unified identification and control scheme capable of achieving space at form performance objectives under nominal or failure conditions is described. Preliminary results are also presented, showing that the methodology offers much promise for effective robust control of large space structures. The control method is a multivariable, adaptive, output predictive controller called Model Predictive Control (MPC). MPC uses a state space model and input reference trajectories of set or tracking points to adaptively generate optimum commands. For a fixed model, MPC processes commands with great efficiency, and is also highly robust. A key feature of MPC is its ability to control either nonminimum phase or open loop unstable systems. As an output controller, MPC does not explicitly require full state feedback, as do most multivariable (e.g., Linear Quadratic) methods. Its features are very useful in LSS operations, as they allow non-collocated actuators and sensors. The identification scheme is based on canonical variate analysis (CVA) of input and output data. The CVA technique is particularly suited for the measurement and identification of structural dynamic processes - that is, unsteady transient or dynamically interacting processes such as between aerodynamics and structural deformation - from short, noisy data. CVA is structured so that the identification can be done in real or near real time, using computationally stable algorithms. Modeling LSS dynamics in 1-g laboratories has always been a major impediment not only to understanding their behavior in orbit, but also to controlling it. In cases where the theoretical model is not confirmed, current methods provide few clues concerning additional dynamical relationships that are not included in the theoretical models. CVA needs no a priori model data, or structure; all statistically significant dynamical states are determined using natural, entropy-based methods. Heretofore, a major limitation in applying adaptive controllers to LSS problems has been the requirement for accurate models. We feel that MPC coupled with the CVA identification scheme will resolve this limitation. The results are based on research performed under an SBIR grant, administered by the Air Force Office of Scientific Research.

Carroll, J. V.↗
NASA NTRS1996

Development of a Large Scale, High Speed Wheel Test Facility

Draper Laboratory, with its internal research and development budget, has for the past two years been funding a joint effort with the Massachusetts Institute of Technology (MIT) for the development of a large scale, high speed wheel test facility. This facility was developed to perform experiments and carry out evaluations on levitation and propulsion designs for MagLev systems currently under consideration. The facility was developed to rotate a large (2 meter) wheel which could operate with peripheral speeds of greater than 100 meters/second. The rim of the wheel was constructed of a non-magnetic, non-conductive composite material to avoid the generation of errors from spurious forces. A sensor package containing a multi-axis force and torque sensor mounted to the base of the station, provides a signal of the lift and drag forces on the package being tested. Position tables mounted on the station allow for the introduction of errors in real time. A computer controlled data acquisition system was developed around a Macintosh IIfx to record the test data and control the speed of the wheel. This paper describes the development of this test facility. A detailed description of the major components is presented. Recently completed tests carried out on a novel Electrodynamic (EDS) suspension system, developed by MIT as part of this joint effort are described and presented. Adaptation of this facility for linear motor and other propulsion and levitation testing is described.

Kondoleon, Anthony↗
NASA NTRS1973

A Real-Time Phase Vector Display for EEG Monitoring

A real-time, computer-based, phase vector display system has been developed which will output a vector whose phase is equal to the delay between a trigger and the peak of a function which is quasi-coherent with respect to the trigger. The system also contains a sliding averager which enables the operator to average successive trials before calculating the phase vector. Data collection, averaging and display generation are performed on a LINC-8 computer. Output displays appear on several X-Y CRT display units and on a kymograph camera/oscilloscope unit which is used to generate photographs of time-varying phase vectors or contourograms of time-varying averages of input functions.

Finger, Herbert J.↗
NASA NTRS1997

Mobile range control center/range safety command destruct and real-time instantaneous impact prediction system

The mobile range control center/range safety command destruct and real time instantaneous impact prediction system (MRCCS), designed for launching sounding rockets and expendable launch vehicles, is described. The MRCCS provides mission control and range safety support for remote launch sites and is equipped with telemetry and radar data acquisition systems, real time data computation systems, range safety display systems, and command destruct transmitters.

Hudson, Sandra Merritt↗
NASA NTRS2003

Estimating Uncertainty in GPCP and TRMM Multi-Satellite Precipitation Estimates

One of the high-priority problems in satellite precipitation estimation is developing algorithms for estimating the errors in precipitation retrievals by individual sensors and subsequent multi-satellite combinations. Classically, we distinguish between "random" and "bias" errors, which do and do not, respectively average to zero over a "big enough" time/space sample. The current operational GPCP and TRMM multi-satellite algorithms are nearly unique in estimating random error for the monthly precipitation estimates from individual sensor systems (including gauge), following Huffman, and then making multi-sensor combinations. No routinely operational global precipitation produces estimates of bias error. Subsequently, a similar scheme has been followed to provide random error estimates for the Multi-satellite Precipitation Analysis (MPA) being computed in real time and after real time for TRMM. The Huffman algorithm for random error is briefly reviewed, including a discussion of the limitations imposed on the algorithm by standard monthly precipitation data sets. Starting from a very simple theoretical treatment of the histogram of precipitation samples in a month, an equation is developed that depends on the estimated average precipitation rate for the month, the number of samples in the month, and two constants. The constants are set separately for each source of precipitation estimate (such as "raingauge") by calibration at selected ground sites. We discuss recent work validating the random error estimates to highlight the successes and limitations of this first-generation approach. We then consider what information is needed from the individual sensor algorithms to facilitate additional accuracy in the estimation of random errors across the time/space span of climate regimes which a global estimation system must handle. In addition, the thorny issue of estimating bias is raised. Finally, the role of error estimates (and the qualitative errors!) in creating combinations of precipitation estimates from different individual sensors is discussed. This issue is particularly important when fine scales in space and time are being considered, say the 0.25 x 0.25-deg 3-hourly estimates in the MPA.

Huffman, G. J.↗