Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron microscopy (SEM)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Relationship of Chemical Composition and Moisture Sensitivity in LiNi x Mn y Co 1-x-y O 2 for Lithium-Ion Batteries

Chemical composition–moisture sensitivity relationship of LiNi x Mn y Co 1-x-y O 2 (NMC) cathode materials was investigated by exploring crystal structures, surface properties, and electrochemical performance behaviors of various commercial NMC powders: LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC111), LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532), LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811). The NMC powders were stored in different moisture conditions: moisture-free, humidified air, or immersed in water. Rietveld refinement analysis of X-ray diffraction (XRD) data and scanning electron microscopy (SEM) were used to characterize the crystal structure changes and the evolution of particle surfaces morphologies. The effect of moisture contamination on the electrochemical properties of NMC cathodes was studied by galvanostatic cycling and electrochemical impedance spectroscopy (EIS). The moisture contamination resulted in either structural disorder or unwanted surficial deposition products, which increased a charge-transfer impedance and consequent performance degradation of battery cells. The results showed that NMC’s moisture vulnerability increased with Ni content (x) despite protective coatings on commercial particles, which stressed the necessity of alternative surface passivation strategies of Ni-rich NMC for broad applications such as electric vehicles and electrified aircraft propulsion.

25 ENERGY STORAGE↗
DOE OSTI2026

Effect of Oil Viscosity and Impact of Ionic Liquid Additive on Electrically Induced Pitting in Rolling Contact

Electrically induced bearing damage (EIBD) is a growing concern in electric drivetrains, where electrical discharge currents generate localized pitting that accelerates wear and premature failure. While ionic liquids (ILs) have shown promise as lubricant additives due to their natural physical adsorption, strong capabilities of tribofilm formation, and high molecular tunability, their role in mitigating EIBD is little known. This gap is especially evident because lubricant viscosity and film thickness affect discharge behavior, and additive performance in these regimes has not been well explored. In this study, tribological tests were performed using a ball-on-disk pure rolling-contact system under an applied voltage on polyalphaolefin oils of three viscosities (4, 10, and 150 cSt measured at 100 °C), with and without the addition of a phosphonium-phosphate IL. Surface damage was analyzed using scanning electron microscopy (SEM) and stylus profilometry. Damage quantification was based on pit morphology analysis of SEM images. The results provide new insights into how oil viscosity governs the discharge behavior and how an IL additive could influence the pit formation. While viscosity seems to play a significant role, an IL additive shows potential to reduce EIBD and deserves further study.

electrically induced bearing damage (EIBD)↗
DOE OSTI2023

Independence of Environmental and Mechanical Damages on Silicone Adhesive Stored in a Thermo-Oxidative Environment

Abstract Elastomeric polymer materials hold a special place in today’s industrial sectors with respect to structural application needs. Low quality materials are detrimental to industries like aerospace, and automotive engineering. Assessment of the durability of elastomers for structural applications has been of much interest among the literary circles for decades and new materials keep outperforming the existing ones. Polymeric adhesives are one of the most abundantly used materials in these industries. All polymeric materials get damaged when in contact with aggressive environments in presence of high temperature and oxygen. Commonly referred to as thermo-oxidation, this environment exposes the material to heat and oxidation reactions in presence of oxygen. Resultantly, during service life, the damage to the polymer matrix is primarily caused by two factors: mechanical damage and environmental aging. Environmental aging is an irreversible phenomenon caused by changes in the molecular structure while mechanical damage maintains the shape of the polymer matrix, and the deterioration is mostly due to polymer chain mobility. Environmental aging can be caused by a single environmental agent or by a synergized impact of several environmental elements. Increasing temperature is found to be proportional to decreasing tensile strength and toughness of material. The rate and extent of degradation can be accessed by scrutinizing the changes in constitutive behavior of material through mechanical and chemical properties. Accelerated thermal aging is among the most common modes of process related degradation, leading generally to chain scission, and crosslinking phenomena and reduced resistance to fracture stress, and strain. In this experimental study, our goal is to separate the environmental degradation from mechanical damage. A silicone-based adhesive was aged in thermo-oxidative at (0%RH) aging environment. The damage and decay mechanisms have been used to draw a distinction between environmental degradation and mechanical damage. Material characterization included uniaxial tensile test (failure and cyclic) and scanning electron microscopy (SEM) tests on as-received and aged samples. Aging was conducted at three different temperatures (60°C, 80°C and 95°C) and six different exposure durations (1, 3, 10, 30, 90 and 200 days). This work confirms that environmental damage is superposed on top of the mechanical damage, and thus, they are separable. The total mechanical and environmental damage is a synergized effect of all exposure conditions and parameters involved i.e., aging time, temperature, and oxygen. The chemistry and mechanics of the polymer degradation were found to be in good agreement with each other.

Alazhary, Sharif↗
DOE OSTI2022

A crystal plasticity finite element method modeling of Zircaloy with hydride phases based on scanning electron micrographs

This work developed a microstructure-based finite element model to predict the stress state of alloys with second phase inclusions. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. Generation of digital microstructure was achieved through two steps of tessellations using software Neper and Matlab. The process is demonstrated using an example of Zircaloy material with secondary phases of hydrides dispersed within and stress-strain response of Zircaloy containing hydrides was predicted. The constitutive material model for Zircaloy in this study was based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as isotropic elasto-plastic material. A parametric study had been conducted to understand the effect of volume fraction, and lamellae thickness of the hydride phase on the mechanical properties of the overall material. Results can help designers to alter the manufacturing process to obtain the enhanced mechanical properties for components used in nuclear applications made by Zircaloy material.

Kulkarni, Shank S.↗
DOE OSTI2023

Mechanical responses of 316L stainless steel printed by wire arc additive manufacturing with different thermal histories

In this paper, 316L stainless steel walls were printed using single-bead pass and multiple-bead pass wire arc additive manufacturing (WAAM), which represent the internal basket wall and external wall of a spent nuclear fuel (SNF) canister; respectively. Scanning electron microscopy (SEM) microstructure characterization and tensile tests at room temperature (21 °C) and elevated temperature (250 °C) were performed on specimens extracted along the length and height directions of the printed walls. Results showed that grain morphology, grain angles, and retained ferrite are different between the two printed walls, which received different heat input in WAAM. The single-bead pass printed wall exhibited higher yield strength than the multiple-bead pass printed wall because of more retained ferrite and larger portion of random-high angle boundaries (RHAB) grains.

Tang, Wei↗
DOE OSTI2020

In situ , in vivo , and in operando imaging and spectroscopy of liquids using microfluidics in vacuum

This review offers a succinct overview of the development of a vacuum-compatible microfluidic reactor system for analysis at the liquid vacuum interface (SALVI), and its diverse applications in in situ, in vivo, and in operando imaging of liquid surfaces as well as the air-liquid (a-l), liquid-liquid (l-l), and solid-liquid (s-l) interfaces in the past decade. SALVI is one of the first microfluidics-based reactors that has enabled direct analysis of volatile liquids in vacuum surface tools such as scanning electron microscopy (SEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Its integration into ambient and vacuum spectroscopy and microscopy is illustrated. Several applications are highlighted including (1) imaging nanoparticles in liquid using in situ SEM; (2) mapping the evolving l-l interface using in situ x-ray absorption spectroscopy and ToF-SIMS; (3) following complex a-l interfacial oxidation reaction products using in situ ToF-SIMS; (4) capturing biological interfaces of cells and microbes via in vivo multimodal and correlative imaging; and (5) monitoring the dynamic solid electrode and liquid electrolyte interface using in operando molecular imaging. Finally, outlook and recommendations are presented. Besides showing the holistic information volume obtained by real-time multiplexed imaging, this review intends to convey the importance of tool development in revolutionizing surface and interface analysis using vacuum platforms previously limited to solid surfaces. Microfluidics is manifested to be not limited to ambient conditions in many examples in this review. Moreover, fundamental interfacial phenomena underpinning mass and charge transfer can now be pursued in real time via innovated chemical imaging and spectroscopy.

42 ENGINEERING↗
DOE OSTI2021

Evolution of Metastable Phases During Mg Metal Corrosion: An In Situ Cryogenic X-ray Photoelectron Spectroscopy Study

Magnesium and its alloys are potential structural materials candidates for a wide variety of applications due to their high strength-to-weight ratio. However, ductility and poor corrosion resistance under ambient environmental conditions are the bottleneck for industrial deployment. Designing passivation layers and/or corrosion resistant alloys requires fundamental understanding of the corrosion process. The traditional ex-situ spectroscopic measurements of polycrystalline metal surface with ubiquitous surface impurities and grain boundaries only provided an indistinct view of the corrosion process. To clearly distinguish the mechanism and sequence of corrosion process, we employed in-situ cryo-based x-ray photoelectron spectroscopy (XPS) measurements on Mg single crystal surface exposed to aqueous salt solution. Clean Mg (0001) surfaces were exposed to pure D2O and NaCl aqueous solution (5 wt% NaCl+95 wt% D2O). The interfacial reactions were studied using multimodal analysis including XPS, x-ray diffraction (XRD) and scanning electron microscopy (SEM). In contrast to previous studies, our experiments demonstrated the formation of magnesium chloride hydroxide hydrate during aqueous salt corrosion processes. Evidence of metastable ClO* radicals were also found during the initial aqueous salt solution exposure.

Shutthanandan, Vaithiyalingam↗
DOE OSTI2021

Quantitative Characterization of the Microstructure-Property Relationships in Ni and MIEC Nanocatalyst-Infiltrated Ni/YSZ Anodes

The performance of solid oxide fuel cell (SOFC) anodes can be improved by infiltration of nanoscale electrocatalysts, which increases triple phase boundary (TPB) density, but only when the added TPBs are active. Quantitative characterization of the microstructure of infiltrated nanocatalysts remains a critical challenge in understanding their role in improved performance. This paper explores the relationship between electrochemical performance and microstructure for Ni/YSZ anodes infiltrated with Ni, gadolinium-doped-ceria (GDC), and Ni/GDC nanocatalysts using a combination of electrochemical impedance spectroscopy (EIS), distribution of relaxation times (DRT) analysis, scanning electron microscopy (SEM) microstructural characterization, and three-dimensional (3-D) anode reconstruction. Estimated polarization resistance improvements as a result of nickel nanoparticle infiltration are discussed.

Rix, Jillian↗
DOE OSTI2022

Conformal Pressure and Fast-Charging Li-Ion Batteries

Batteries capable of extreme fast-charging (XFC) are a necessity for the deployment of electric vehicles. Material properties of electrodes and electrolytes along with cell parameters such as stack pressure and temperature have coupled, synergistic, and sometimes deleterious effects on fast-charging performance. We develop a new experimental testbed that allows precise and conformal application of electrode stack pressure. We focus on cell capacity degradation using single-layer pouch cells with graphite anodes, LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) cathodes, and carbonate-based electrolyte. In the tested range (10–125 psi), cells cycled at higher pressure show higher capacity and less capacity fading. Additionally, Li plating decreases with increasing pressure as observed with scanning electron microscopy (SEM) and optical imaging. While the loss of Li inventory from Li plating is the largest contributor to capacity fade, electrochemical and SEM examination of the NMC cathodes after XFC experiments show increased secondary particle damage at lower pressure. We infer that the better performance at higher pressure is due to more homogeneous reactions of active materials across the electrode and less polarization through the electrode thickness. Our study emphasizes the importance of electrode stack pressure in XFC batteries and highlights its subtle role in cell conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Facile Electrodeposition and Aging to Generate 3-Dimensional α-MnO 2 Battery Cathodes

Conventional tape casting forms 2-dimensional (2D) electrodes containing active material, conductive additive, and binder with restricted ion access as electrodes increase in thickness. To improve the transport properties, 3D architectures were developed using electrodeposition to ensure contact between the active material with the substrate, and provide enhanced electrolyte access. This paper investigates electrodeposition of cryptomelane ( α -MnO 2 ) as a model cathode material to efficiently accommodate (de)lithation and increase areal capacity vs conventional 2D coatings. Electodeposited samples on titantium (Ti) foil substrates were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) and show a linear increase of the average oxidation of Mn (3.5–3.8) and active mass loading (1.27–9.9 mg) with deposition and aging times (0–120 min). The initial deposition is amorphous and forms the crystalline material during the elevated temperature aging step. The active material, α -MnO 2 , was also deposited on C-cloth and these cathodes at deposition times of 3, 6, and 9 min deliver 9, 36, and 69% higher areal capacities, respectively, at 0.2 mA cm −2 compared to conventional 2D electrodes with a mass loading equal to the 3 min sample. These results demonstrate the benefit of α -MnO 2 within a porous architecture providing enhanced transport properties.

Electrochemistry↗
DOE OSTI2024

Modeling and Analysis of Polarization Losses in Solid Oxide Fuel Cells with Siloxane Contamination

In this study, the degradation of the solid-oxide fuel cell (SOFC) nickel-yttria stabilized zirconia anode under decamethyltetrasiloxane (L4) contamination is examined with experiments and modeling. A model is developed for the polarization losses based on the charge transfer coefficient,α, and diffusion layer thickness,δ, and fitted to the experimental data to understand how the siloxane degrades the SOFC performance with time. The results of the model indicate that the total polarization losses increase approximately 44% over the course of the 180 min experiment at 350 mA cm −2 . Activation losses dominate the polarization losses initially but decrease in their total contribution while concentration losses increase. Scanning electron microscopy (SEM) with wavelength dispersive X-ray spectroscopy (WDS) elemental mapping indicates that silicon deposition is highest at the outer edge of the anode and forms a barrier layer to fuel diffusion, increasing concentration losses. When the model is applied to other previous D4 and L4 siloxane experiments conducted over a period of 40 h, similar trends in polarization losses are observed. Polarization losses increase more rapidly with D4 compared to L4 siloxane contamination, with concentration losses increasing the fastest with both types of siloxane.

Electrochemistry↗
DOE OSTI2020

Fracture, Dissolution, and Cementation Events in Ordovician Carbonate Reservoirs, Tarim Basin, NW China

Ordovician carbonate rocks of the Yijianfang Formation in the Tabei Uplift, Tarim Basin, contain deeply buried (>6000 m), highly productive oil and gas reservoirs associated with large cavities (>10 m). Previous workers inferred that large cavities are paleocaves (paleokarst) formed near the surface and subsequently buried. Alternately, caves may have formed by dissolution at depth along faults. Using 227 samples from 16 cores, we document textures and cement compositions bearing on cavity histories with petrographic, high-resolution scanning electron microscopy (SEM), isotopic, and fluid inclusion microthermometric observations. Results show that dissolution occurred at depth and was caused by (1) acidic fluids derived from Middle-Late Silurian and/or Devonian-Permian hydrocarbon generation and maturation, (2) high-temperature fluids, of which some were associated with Late Permian igneous activity, and (3) Mg-rich fluids that accompanied Jurassic-Cretaceous deformation and the formation of partially open fractures and stylobreccias (fault breccias). The relative paragenetic sequence of the structure-related diagenesis suggests seven stages of fracturing, dissolution, and cementation. Mottle fabrics in the Yijianfang Formation contain argillaceous carbonate-rich silt and are bioturbation features formed within the marine environment. Those mottled fabrics differ from clearly karstic features in the overlying Lianglitage Formation, which formed by near-surface dissolution and subsequent infilling of cavities by allochthonous sediment. Mottle fabrics are crosscut by compacted fractures filled with phreatic-vadose marine cements and followed by subsequent generations of cement-filled fractures and vugs indicating that some fractures and vugs became cement filled prior to later dissolution events. Calcite cements in fractures and vugs show progressively depleted values of δ18O documenting cement precipitation within the shallow (~220 m), intermediate (~625 m), and deep (~2000 m) diagenetic environments. Deep (mesogenetic) dissolution associated with fractures is therefore the principal source of the high porosity-permeability in the reservoir, consistent with other pieces of evidence for cavities localized near faults.

58 GEOSCIENCES↗
DOE OSTI2021

Characterization of Nanoscale Pores in Tight Gas Sandstones Using Complex Techniques: A Case Study of a Linxing Tight Gas Sandstone Reservoir

Pore structures with rich nanopores and permeability in tight gas reservoirs are poorly understood up to date. Advanced techniques are needed to be employed to accurately characterize pore structures, especially tiny pores which include micron and nanopores. In this study, various experimental techniques such as scanning electron microscopy (SEM), nuclear magnetic resonance (NMR) T 2 , nitrogen adsorption method, and NMR cryoporometry (NMRC) are combined to interrogate the complex pore systems of the tight gas reservoir in the Linxing formation, Ordos Basin, China. Results show that tight gas sandstones are primarily comprised of residual interparticle and clay-dominated pores. Clay and quartz are two dominate minerals while pyrite occupies a nontrivial amount as well. The permeability of tight gas sandstones is very low, exhibiting an extremely poor positive correlation with porosity. While pore types and relative pore contents are more influential factors on the permeability, accurate characterization of pore size distribution is critical for the permeability of tight gas sandstones. Therefore, complementary characterization methods are carried out, indicating that neither small pores with radii < 100 nm (around peak 1 in NMR T 2 distribution) nor large pores with radii > 5 μ m (around peak 3 in NMR T 2 distribution) control the permeability by analyzing the connectivity of the pores in various size ranges, but rather pores averaging approximately 350 ± X nm (around peak 2 in NMR T 2 distribution) have sufficient connectivity to host and transmit hydrocarbons. The pore size of tight gas sandstones is dominated by the clay-rich mineral assemblage. The study shows that the NMRC technique can be a very promising method, especially when referred to as a promising “roadmap” on how to interrogate tight formations such as the tight gas sands or even shale especially for the nanopore characterization.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

AutoEMX v1.

The invention consists in the full automation of compositional analysis of inorganic powder samples by scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS). The measurements and analysis are controlled via python-based software, Auto-SEMEDS. Auto-SEMEDS fully automates the SEM-EDS measurements, and analyses the collected data via the use of machine-learning (ML) algorithms, which have never been used before for such scope. Auto-SEMEDS enables the identification in fully-automated fashion of the individual material phases present in a powder sample. Similar technologies, such as commercial SEM-EDS software, can automatically classify particles based on their composition, but they have significant limitations. These solutions typically provide inaccurate composition measurements and struggle to identify single phases in lab samples, where phases are often closely intermixed. In contrast, Auto-SEMEDS achieves unprecedented accuracy in composition measurements of powder samples, and furthermore leverages machine learning algorithms to effectively discern intermixed phases. Notably, while previous studies have demonstrated accurate measurements on individual particles, Auto-SEMEDS stands out by successfully analyzing mixture of different phases, a capability that has not been reported in the literature until now.

Giunto, Andrea [Lawrence Berkeley National Laborat↗
DOE OSTI2023

Ballistic characterization of additively manufactured extrusion deposited thermoplastic composite plates

Additive manufacturing (AM) is rapidly emerging in high performance applications such as army ground vehicles, automotive and transportation. However, the response of AM parts/components to extreme loading such as high velocity impacts is less studied. In this work, the performance under ballistic impact of AM panels is evaluated using a medium velocity gas gun, generating projectile velocities up to 400 m/s. The preferential print orientation properties are considered in order to evaluate whether the panels exhibit isotropic or anisotropic behavior under impact. Surface morphology is investigated by milling the beads smooth on samples and comparing the impact on as-printed samples to those that are smoothed. The effect of nickel chromium micron (nichrome) wire embedded in the AM panels (during print) of polycarbonate-carbon fiber (PC-CF) and polycarbonate-glass fiber (PC-GF) are explored. Thermoplastic polyurethane-acrylonitrile butadiene styrene/carbon fiber (TPU-ABS/CF), Acrylonitrile butadiene styrene-carbon-fiber (ABS-CF) AM samples absorbed >50% of the impact energy. The ballistic performance was noted to be in the following order – ABS-CF > TPU-ABS/CF > PC. Scanning electron microscopy (SEM) was conducted to study the interface between the nichrome wire and the polymer-fiber matrix. This work is the first of its kind exploring into the capabilities of AM panels as ballistic materials. This study leads the way for developing AM panels that are easily manufactured and exhibit superior ballistic resistance.

Landrie, Dakota M.↗
DOE OSTI2024

Silicate coprecipitation reduces green rust crystal size and limits dissolution-precipitation during air oxidation

Green rusts (GR) are mixed-valence iron (Fe) hydroxides which form in reducing redox environments like riparian and wetland soils and shallow groundwater. In these environments, silicon (Si) can influence Fe oxides’ chemical and physical properties but its role in GR formation and subsequent oxidative transformation have not been studied starting at initial nucleation. Green rust sulfate [GR(SO 4 )] and green rust carbonate [GR(CO 3 )] were both coprecipitated from salts by base titration in increasing % mol Si (0, 1, 10, and 50). The minerals were characterized before and after rapid (24 h) aqueous air-oxidation by x-ray diffraction (XRD), scanning electron microscopy (SEM), Fe extended x-ray absorption fine structure spectroscopy (EXAFS), and N 2 -BET surface area. Results showed that only GR(SO4) or GR(CO3) was formed at every tested Si concentration. Increasing % mol Si caused decreased plate size and increased surface area in GR(CO3) but not GR(SO4). GR plate basal thickness was not changed at any condition indicating a lack of Si interlayering. Air oxidation of GR(SO4) at all % mol Si contents transformed by dissolution and reprecipitation into lepidocrocite and goethite, favoring ferrihydrite with higher % Si content. Air oxidation of GR(CO3) transformed into magnetite and goethite but increasing Si caused GR to oxidize while retaining its hexagonal plate structure via solid-state oxidation. Our results indicate that Si has the potential to cause GR to form in smaller particles and upon air oxidation, Si can either stabilize the plate structure or alter transformation to ferrihydrite.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Designing an impedance-based technique for studying corrosion on cladding materials

In nuclear cladding materials, changes in structure and chemistry over the lifetime of claddings can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel and cladding materials can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides. The objective of this study is to develop an impedance based sensing technology for measuring spatial- and time-resolved in-pile changes in cladding chemistry in order to understand the mechanisms of hydride formation, hydride dealloying and associated cladding corrosion so that a mitigation strategy and technology can be developed for reactor safe operation. Two prototype impedance-based sensors were designed and assembled using Zr-4 as working electrode and Pt as counter and reference electrode. One sensor is tubular type and the other one is plate-type. These sensors will be tested in static autoclave to investigate the effects of various environmental conditions (including temperature, pressure, and water chemistry) on cladding material corrosion mechanisms. These in-situ EIS sensors would provide corrosion-layer parameters in high-temperature water, such as (1) total layer thickness, (2) the evolution of oxide structures as uniform layer dielectric or sublayer(s), and (3) the possible electrochemistry of the volume corrosion process and the solid/liquid interface, such as the cyclic nature of corrosion of Zr alloys in high-temperature water. This work was focused on electrochemical sensor development, targeting cladding oxides/hydrides under thermodynamic equilibria; characterization of samples using Kelvin probe force microscopy (SKPFM), Raman spectroscopy, and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) to provide high-resolution co-localized characterization of zirconium oxide and metal/oxide interface.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Photoluminescence probing of light absorption centers at silica laser damage

We use photoluminescence (PL) imaging to study damage growth precursors within laser damage sites on the surface of silica. Damage site evolution is induced by multiple shots of UV nanosecond pulsed laser at various energy densities and monitored throughout the early stages of growth. Wide-field PL imaging rapidly locates microscopic light absorption centers within the silica damage site. Our quantitative analysis shows that damage sites with strong local PL intensity show a higher probability of growth upon subsequent laser pulses. Scanning electron microscopy (SEM) paired with a study of PL spectrum shows that the strong PL intensity appears from the subsurface fractures with high defect density, which provides a local light absorption center leading to significant damage growth. We believe that this result offers an efficient optical damage mitigation strategy by providing a rapid and non-destructive optical inspection approach.

36 MATERIALS SCIENCE↗