Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Dynamical Evolution of the Debris Disk after a Satellite Catastrophic Disruption around Saturn

The hypothesis of the recent origin of Saturn’s rings and its midsized moons is actively debated. It was suggested that a proto-Rhea and a proto-Dione might have collided recently, giving birth to the modern system of midsized moons. It has also been suggested that the rapid viscous spreading of the debris may have implanted mass inside Saturn’s Roche limit, giving birth to its modern ring system. However, this scenario has only been investigated in a very simplified way for the moment. This paper investigates it in detail to assess its plausibility by using N -body simulations and analytical arguments. When the debris disk is dominated by its largest remnant, N -body simulations show that the system quickly reaccretes into a single satellite without significant spreading. On the other hand, if the disk is composed of small particles, analytical arguments suggest that the disk experiences dynamical evolutions in three steps. The disk starts significantly excited after the impact and collisional damping dominates over the viscous spreading. After the system flattens, the system can become gravitationally unstable when particles are smaller than ∼100 m. However, the particles grow faster than spreading. Then, the system becomes gravitationally stable again and accretion continues at a slower pace, but spreading is inhibited. Therefore, the debris is expected to reaccrete into several large bodies. In conclusion, our results show that such a scenario may not form today’s ring system. In contrast, our results suggest that today’s midsized moons are likely reaccreted from such a catastrophic event.

79 ASTRONOMY AND ASTROPHYSICS↗

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 2: AFT C.G. simulation and analysis

Relaxed static stability and stability augmentation with active controls were investigated for subsonic transport aircraft. Analytical and simulator evaluations were done using a contemporary wide body transport as a baseline. Criteria for augmentation system performance and unaugmented flying qualities were evaluated. Augmentation control laws were defined based on selected frequency response and time history criteria. Flying qualities evaluations were conducted by pilots using a moving base simulator with a transport cab. Static margin and air turbulence intensity were varied in test with and without augmentation. Suitability of a simple pitch control law was verified at neutral static margin in cruise and landing flight tasks. Neutral stability was found to be marginally acceptable in heavy turbulence in both cruise and landing conditions.

Urie, D. M.↗

CFD Simulations of Supersonic Highly Swirling Flow Exiting a Turbine Vane Row Compared with Experimental Observations

Marshall Space Flight Center (MSFC) has been heavily involved in developing the J2-X engine. The Center has been testing a Work Horse Gas Generator (WHGG) to supply gas products to J2-X turbine components at realistic flight-like operating conditions. Three-dimensional time accurate CFD simulations and analytical fluid analysis have been performed to support WHGG tests at MSFC. The general purpose CFD program LOCI/Chem was utilized to simulate flow of products from the WHGG through a turbine manifold, a stationary row of turbine vanes, into a Can and orifice assembly used to control the back pressure at the turbine vane row and finally through an aspirator plate and flame bucket. Simulations showed that supersonic swirling flow downstream of the turbine imparted a much higher pressure on the Can wall than expected for a non-swirling flow. This result was verified by developing an analytical model that predicts wall pressure due to swirling flow. The CFD simulations predicted that the higher downstream pressure would cause the pressure drop across the nozzle row to be approximately half the value of the test objective. With CFD support, a redesign of the Can orifice and aspirator plate was performed. WHGG experimental results and observations compared well with pre-test and post-test CFD simulations. CFD simulations for both quasi-static and transient test conditions correctly predicted the pressure environment downstream of the turbine row and the behavior of the gas generator product plume as it exited the WHGG test article, impacted the flame bucket and interacted with the external environment.

West, Jeff S.↗

Simulation Exploration through Immersive Parallel Planes

We present a visualization-driven simulation system that tightly couples systems dynamics simulations with an immersive virtual environment to allow analysts to rapidly develop and test hypotheses in a high-dimensional parameter space. To accomplish this, we generalize the two-dimensional parallel-coordinates statistical graphic as an immersive 'parallel-planes' visualization for multivariate time series emitted by simulations running in parallel with the visualization. In contrast to traditional parallel coordinate's mapping the multivariate dimensions onto coordinate axes represented by a series of parallel lines, we map pairs of the multivariate dimensions onto a series of parallel rectangles. As in the case of parallel coordinates, each individual observation in the dataset is mapped to a polyline whose vertices coincide with its coordinate values. Regions of the rectangles can be 'brushed' to highlight and select observations of interest: a 'slider' control allows the user to filter the observations by their time coordinate. In an immersive virtual environment, users interact with the parallel planes using a joystick that can select regions on the planes, manipulate selection, and filter time. The brushing and selection actions are used to both explore existing data as well as to launch additional simulations corresponding to the visually selected portions of the input parameter space. As soon as the new simulations complete, their resulting observations are displayed in the virtual environment. This tight feedback loop between simulation and immersive analytics accelerates users' realization of insights about the simulation and its output.

97 MATHEMATICS AND COMPUTING↗

Magnetized Disruption of Inertially Confined Plasma Flows

Herein, the creation and disruption of inertially collimated plasma flows are investigated through experiment, simulation, and analytical modeling. Supersonic plasma jets are generated by laser-irradiated plastic cones and characterized by optical interferometry measurements. Targets are magnetized with a tunable $B$ field with strengths of up to 5 T directed along the axis of jet propagation. These experiments demonstrate a hitherto unobserved phenomenon in the laboratory, the magnetic disruption of inertially confined plasma jets. This occurs due to flux compression on axis during jet formation and can be described using a Lagrangian-cylinder model of plasma evolution implementing finite resistivity. The basic physical mechanisms driving the dynamics of these systems are described by this model and then compared with two-dimensional radiation-magnetohydrodynamic simulations. Experimental, computational, and analytical results discussed herein suggest that contemporary models underestimate the electrical conductivity necessary to drive the amount of flux compression needed to explain observations of jet disruption.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cascaded radiation pressure acceleration

A cascaded radiation-pressure acceleration scheme is proposed. When an energetic proton beam is injected into an electrostatic field moving at light speed in a foil accelerated by light pressure, protons can be re-accelerated to much higher energy. An initial 3-GeV proton beam can be re-accelerated to 7 GeV while its energy spread is narrowed significantly, indicating a 4-GeV energy gain for one acceleration stage, as shown in one-dimensional simulations and analytical results. The validity of the method is further confirmed by two-dimensional simulations. This scheme provides a way to scale proton energy at the GeV level linearly with laser energy and is promising to obtain proton bunches at tens of gigaelectron-volts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ku-band radar threshold analysis

The statistics of the CFAR threshold for the Ku-band radar was determined. Exact analytical results were developed for both the mean and standard deviations in the designated search mode. The mean value is compared to the results of a previously reported simulation. The analytical results are more optimistic than the simulation results, for which no explanation is offered. The normalized standard deviation is shown to be very sensitive to signal-to-noise ratio and very insensitive to the noise correlation present in the range gates of the designated search mode. The substantial variation in the CFAR threshold is dominant at large values of SNR where the normalized standard deviation is greater than 0.3. Whether or not this significantly affects the resulting probability of detection is a matter which deserves additional attention.

Weber, C. L.↗

Development and Test of a New Verification Scheme for Transient Core Simulators

Transient calculations in commercial nuclear reactors are performed while typically relying on a time-dependent neutron transport solver or a low-order solver (i.e. diffusion). In order to be licensed, the codes used by the industry need to go through a process of verification and validation, with the verification carried out by comparing the results of simulations to analytical or semi-analytical solutions. Such analytical or semi-analytical solutions can only be obtained if the system to be modelled during the verification process is either fully homogeneous or piecewise homogeneous. This paper reports on the development of a different verification approach that can be applied to fully heterogeneous systems. It relies on the extraction of the point-kinetic response of the reactor (which can be estimated from the results of core simulations) and on its subsequent comparison with its expected analytical form.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Navigation simulator for the Space Tug vehicle

A general simulation program (GSP) for state estimation of a nonlinear space vehicle flight navigation system is developed and used as a basis for evaluating the performance of a Space Tug navigation system. An explanation of the iterative guidance mode (IGM) guidance law, derivation of the dynamics, coordinate frames and state estimation routines are given in order to clarify the assumptions and approximations made. A number of simulation and analytical studies are used to demonstrate the operation of the Tug system. Included in the simulation studies are (1) initial offset vector parameter study; (2) propagation time vs accuracy; (3) measurement noise parametric study and (4) reduction in computational burden of an on-board implementable scheme. From the results of these studies, conclusions and recommendations concerning future areas of practical and theoretical work are presented.

Colburn, B. K.↗

Comparison between analytical models and finite-difference simulations in transmission-line tap resistors and L-type cross-Kelvin resistors

Approximate analytical models of the transmission-line tap resistor and the cross-Kelvin resistor are compared with computer-simulated pseudo-three-dimensional resistor network models. The analytical formulas are in good agreement with the simulations over a useful range of parameters and are readily applied to the extraction of the contact resistivity and the sheet resistances of the semiconducting layer under and outside the contacts. The extraction procedure, which is easily implemented on a personal computer, is carried out for the case of alloyed AuGeNi/GaAs contacts, illustrating the importance of (1) distinguishing between layer sheet resistance under and outside the contacts and (2) considering two-dimensional current flow in the semiconducting layer.

Scorzoni, Andrea↗

Calculated Effects of Nitric Oxide Flow Contamination on Scramjet Performance

The level of nitric oxide contamination in the test gas of the NASA Langley Research Center Arc-Heated Scramjet Test Facility and the effect of the contamination on scramjet test engine performance were investigated analytically. The study was conducted for standard facility conditions corresponding to Mach 6, 7, and 8 flight simulations. The analytically determined levels of nitric oxide produced in the facility are compared with experimentally measured levels. Results of the analysis indicate that nitric oxide levels range from one to three mole percent, which corroborates the measured levels. A three-stream combustor code with finite rate chemistry was used to investigate how nitric oxide affects scramjet performance in terms of combustor pressure rise, heat release, and thrust performance. Results indicate minimal effects on engine performance for the test conditions of this investigation.

Fischer, Karen E.↗

Preliminary Geological Findings on the BP-1 Simulant

The following is a summation of information and discussion between Doug Stoeser of the USGS and Doug Rickman of NASA in February and March, 2010 pertaining to the BP-1 simulant. The analytical results and the bulk of the text are from communications from Dr. Stoeser. The BP-1 simulant is made from Black Point Basalt Flow, San Francisco Volcanic Field, northern Arizona. There is an aggregate (road metal) quarry on the northern margin of the flow towards the west end that was used as a Desert Research and Technology Studies (Desert RATS) analog test site. Silty material from this site was also used in laboratory tests and found to have geotechnical properties similar to the LHT-2M and Chenobi regolith simulants and is being proposed as a possible simulant for geotechnical use. It currently has the designation of BP-1 (Black Point 1). Figure

Rickman, D. L.↗

THREAT ANTICIPATION AND DECEPTIVE REASONING USING BAYESIAN BELIEF NETWORKS

Recent events highlight the need for tools to anticipate threats posed by terrorists. Assessing these threats requires combining information from disparate data sources such as analytic models, simulations, historical data, sensor networks, and user judgments. These disparate data can be combined in a coherent, analytically defensible, and understandable manner using a Bayesian belief network (BBN). In this paper, we develop a BBN threat anticipatory model based on a deceptive reasoning algorithm using a network engineering process that treats the probability distributions of the BBN nodes within the broader context of the system development process.

97 MATHEMATICS AND COMPUTING↗

Analysis and Simulation of the Simplified Aircraft-Based Paired Approach Concept With the ALAS Alerting Algorithm in Conjunction With Echelon and Offset Strategies

This report presents analytical and simulation results of an investigation into proposed operational concepts for closely spaced parallel runways, including the Simplified Aircraft-based Paired Approach (SAPA) with alerting and an escape maneuver, MITRE?s echelon spacing and no escape maneuver, and a hybrid concept aimed at lowering the visibility minima. We found that the SAPA procedure can be used at 950 ft separations or higher with next-generation avionics and that 1150 ft separations or higher is feasible with current-rule compliant ADS-B OUT. An additional 50 ft reduction in runway separation for the SAPA procedure is possible if different glideslopes are used. For the echelon concept we determined that current generation aircraft cannot conduct paired approaches on parallel paths using echelon spacing on runways less than 1400 ft apart and next-generation aircraft will not be able to conduct paired approach on runways less than 1050 ft apart. The hybrid concept added alerting and an escape maneuver starting 1 NM from the threshold when flying the echelon concept. This combination was found to be effective, but the probability of a collision can be seriously impacted if the turn component of the escape maneuver has to be disengaged near the ground (e.g. 300 ft or below) due to airport buildings and surrounding terrain. We also found that stabilizing the approach path in the straight-in segment was only possible if the merge point was at least 1.5 to 2 NM from the threshold unless the total system error can be sufficiently constrained on the offset path and final turn.

Torres-Pomales, Wilfredo↗

Computer Simulations of Bottle Brushes: From Melts to Soft Networks

We use a combination of Molecular dynamics simulations and analytical calculations, and study dens bottle-brush systems in a melt and network State. Analysis of our simulation results shows that bottle-brush macromolecules in melt behave as ideal chains with effective Kuhn length b K . Simulations show that the bottle-brush-induced bending rigidity is due to an entropy decrease caused by redistribution of the side chains upon backbone bending. The Kuhn length of the bottle:brushes increases with increasing the side-chain degree of polymerization n sc as b K proportional to n sc 0.46 . Moreover, this model of bottle brush macromolecules is extended to describe mechanical properties of bottle brush networks in linear and nonlinear deformation regimes. In the linear deformation regime, the network shear modulus scales with the degree of polymerization of the side chains as G 0 proportional to (n sc + 1) -1 as long as the ratio of the Kuhn length, b K , to the size of the fully extended bottle-brush backbone between cross-links, R-max, is smaller than unity, b K /R max << 1. Bottle-brush networks With b K /R max proportional to 1 demonstrate behavior similar to that of networks Of semiflexible chains with G 0 proportional to n sc -0.5 . Finally, in the nonlinear network deformation regime, the deformation-dependent shear modulus is a universal function of the first strain invariant I 1 and bottle-brush backbone deformation ratio beta describing stretching ability of the bottle-brush backbone between cross-links.

97 MATHEMATICS AND COMPUTING↗

A Framework Including Recombination for Analyzing the Dynamics of Within-Host HIV Genetic Diversity

This paper presents a novel population genetic model and a computationally and statistically tractable framework for analyzing within-host HIV diversity based on serial samples of HIV DNA sequences. This model considers within-host HIV evolution during the chronic phase of infection and assumes that the HIV population is homogeneous at the beginning, corresponding to the time of seroconversion, and evolves according to the Wright-Fisher reproduction model with recombination and variable mutation rate across nucleotide sites. In addition, the population size and generation time vary over time as piecewise constant functions of time. Under this model I approximate the genealogical and mutational processes for serial samples of DNA sequences by a continuous coalescent-recombination process and an inhomogeneous Poisson process, respectively. Based on these derivations, an efficient algorithm is described for generating polymorphisms in serial samples of DNA sequences under the model including various substitution models. Extensions of the algorithm are also described for other demographic scenarios that can be more suitable for analyzing the dynamics of genetic diversity of other pathogens in vitro and in vivo . For the case of the infinite-sites model, I derive analytical formulas for the expected number of polymorphic sites in sample of DNA sequences, and apply the developed simulation and analytical methods to explore the fit of the model to HIV genetic diversity based on serial samples of HIV DNA sequences from 9 HIV-infected individuals. The results particularly show that the estimates of the ratio of recombination rate over mutation rate can vary over time between very high and low values, which can be considered as a consequence of the impact of selection forces.

60 APPLIED LIFE SCIENCES↗

Large-scale gas dynamical processes affecting the origin and evolution of gaseous galactic halos

Observations of galactic halo gas are consistent with an interpretation in terms of the galactic fountain model in which supernova heated gas in the galactic disk escapes into the halo, radiatively cools and forms clouds which fall back to the disk. The results of a new study of several large-scale gas dynamical effects which are expected to occur in such a model for the origin and evolution of galactic halo gas will be summarized, including the following: (1) nonequilibrium absorption line and emission spectrum diagnostics for radiatively cooling halo gas in our own galaxy, as well the implications of such absorption line diagnostics for the origin of quasar absorption lines in galactic halo clouds of high redshift galaxies; (2) numerical MHD simulations and analytical analysis of large-scale explosions ad superbubbles in the galactic disk and halo; (3) numerical MHD simulations of halo cloud formation by thermal instability, with and without magnetic field; and (4) the effect of the galactic fountain on the galactic dynamo.

Shapiro, Paul R.↗