Search NASA⌕ Search

SEARCH · Search NASA

Results for “single crystal transformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Creep Resistance of ZrO2 Ceramic Improved by the Addition of a Small Amount of Er2O3

Zirconia (ZrO2) has great technological importance in structural, electrical, and chemical applications. It is the crucial component for state-of-the art thermal barrier coatings and an enabling component as a solid electrolyte for solid-oxide fuel cell systems. Pure ZrO2 is of limited use for industrial applications because of the phase transformations that occur. Upon the addition of stabilizers, cubic (c-ZrO2) and tetragonal (t-ZrO2) forms can be preserved. It is the stabilized and partially stabilized forms of zirconia that function as thermal barrier coatings, solid electrolytes, and oxygen sensors and that have numerous applications in the electrochemical industry. The cubic form of ZrO2 is typically stabilized through Y2O3 additions. However, Y2O3-stabilized zirconia is susceptible to deformation at high temperatures (greater than 900 C) because of the large number of slip systems and the high oxygen diffusion rates, which result in high creep rates at high temperatures. Successful use of ZrO2 at high temperatures requires that new dopant additives be found that will retain or enhance the desirable properties of cubic ZrO2 and yet produce a material with lower creep rates. At the NASA Glenn Research Center, erbium oxide (Er2O3) was identified as a promising dopant for improving the creep resistance of. ZrO2. The selection of Er2O3 was based on the strong interactions of point defects and dislocations. Single crystals of 5 mol% Er2O3- doped ZrO2 rods (4 mm in diameter) and monofilaments (200 to 300 mm in diameter and 30 cm long) were grown using the laser-heated float zone technique, and their creep behavior was measured as a function of temperature. The addition of 5 mol% Er2O3 to single-crystal ZrO2 improved its creep resistance at high temperatures by 2 to 3 orders of magnitude over state-of-the-art Y2O3-doped crystals. Detailed microstructural characterization of ZrO2-Er2O3 single crystals has identified new mechanisms for improving the creep resistance of this class of materials. Adding Er2O3 to ZrO2 results in microstructure of stable and metastable tetragonal precipitates that with thermal treatment evolve to a tweed structure of nanosize tetragonal lamellae. The superior high-temperature creep resistance of Er2O3-doped ZrO2 is attributed to nanoscale precipitation hardening. Doping with Er2O3 will significantly increase the upper-use temperature limit of ZrO2. Potential applications include using Er2O3-doped ZrO2 as a high-temperature fiber for structural applications and adding Er2O3 to reduce the sintering rates of ZrO2 thermal barrier coatings. This work was conducted at Dpto. de F sica de la Materia Condensada, Universidad de Sevilla, Spain, and at NASA Glenn.

Martinez-Fernandez, Julian↗
DOE OSTI2022

New large-strain FFT-based formulation and its application to model strain localization in nano-metallic laminates and other strongly anisotropic crystalline materials

This paper presents a new robust large-strain (LS) elasto-viscoplastic (EVP) formulation based on Fast Fourier Transforms (FFTs) for the prediction of the micro-mechanical response and microstructure evolution of polycrystalline and multiphase materials, with emphasis on the effect of strong crystallographic and/or morphologic anisotropy on localization of plastic deformation. In this work, the novel LS-EVPFFT formulation allows treatment of complex initial geometries and large deformations considering three grids of material points: a regular grid in the reference configuration, where FFTs can be performed; an irregular grid in the initial configuration, created by applying a stress-free displacement field to the reference regular grid; and an irregular grid in the current configuration, undergoing large strains and rotations as the material is loaded. Further numerical stability of the new formulation also required the use of a novel expression for the discrete modified Green’s operator, which reduces spurious field oscillations. After presenting and validating the new formulation by comparison with preexisting implementations and analytical solutions, LS-EVPFFT is applied to the prediction of slip and kink bands formation in polycrystalline columnar ice, and kink bands in single crystal zinc wires, showing good agreement with classic experiments. Finally, the model is used to study kink band formation during compression of Cu–Nb nano-metallic laminates (NMLs), in which accurate treatment of the complex geometry associated with the tortuosity of interfaces and large deformations become critical, showing consistency with corresponding micropillar experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shock compression of silver to 300 GPa: Wave profile measurements and melting transition

Recent in-situ x-ray diffraction (XRD) measurements on laser-shock compressed Ag foils demonstrated a face-centered-cubic to body-centered-cubic transformation at ~150 GPa and melting between 172 and 197 GPa [Phys. Rev. Lett. 124, 235701 (2020)]. As a complement to the XRD work, we conducted plate impact experiments to obtain shock velocity and wave profile measurements on thicker Ag samples shock-compressed to peak stresses between 30 and 300 GPa. The shock velocity–particle velocity results were fitted very well by a linear relation over the entire stress range, providing an accurate determination of the Ag Hugoniot (locus of the stress-volume states achieved under shock compression). For peak stresses below 187 GPa and above 210 GPa—corresponding to the solid and liquid phases, respectively—the wave profiles show clean single waves. No wave profile features related to the fcc-bcc transformation at ~150 GPa were observed, implying minimal volume change for the transformation. For stresses between 187 and 210 GPa, an initial jump was followed by a time-dependent increase in the particle velocity (20–80 ns risetime) to the peak state—corresponding to the solid-liquid mixed phase response. Unlike the solid and liquid response, the mixed-phase response cannot be readily analyzed analytically. Instead, numerical simulations incorporating an accurate multiphase equation of state for Ag—not currently available—are required to analyze the wave profiles measured at 187–210 GPa stresses. Furthermore, the present work shows the potential for using wave profile measurements to examine the melting transition under shock compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2000

Over-Expression, Purification and Crystallization of Human Dihydrolipoamide Dehydrogenase

Dehydrolipoamide dehydrogenase (E3; dihydrolipoan-tide:NAD+ oxidoreductase, EC 1.8.1.4) is a common catalytic component found in pyruvate dehydrogenase complex, alpha-ketoglutarate dehydrogenase complex, and branched-chain cc-keto acid dehydrogenase complex. E3 is also a component (referred to as L protein) of the glycine cleavage system in bacterial metabolism (2). Active E3 forms a homodimer with four distinctive subdomain structures (FAD binding, NAD+ binding, central and interface domains) with non-covalently but tightly bound FAD in the holoenzyme. Deduced amino acids from cloned full-length human E3 gene showed a total of 509 amino acids with a leader sequence (N-terminal 35 amino acids) that is excised (mature form) during transportation of expressed E3 into mitochondria membrane. So far, three-dimensional structure of human E3 has not been reported. Our effort to achieve the elucidation of the X-ray crystal structure of human E3 will be presented. Recombinant pPROEX-1 expression vector (from GIBCO BRL Life Technologies) having the human E3 gene without leader sequence was constructed by Polymerase Chain Reaction (PCR) and subsequent ligation, and cloned in E.coli XL1-Blue by transformation. Since pPROEX-1 vector has an internal His-tag (six histidine peptide) located at the upstream region of a multicloning site, one-step affinity purification of E3 using nickelnitriloacetic acid (Ni-NTA) agarose resin, which has a strong affinity to His-tag, was feasible. Also a seven-amino-acid spacer peptide and a recombinant tobacco etch virus protease recognition site (seven amino acids peptide) found between His-tag and first amino acid of expressed E3 facilitated the cleavage of His-tag from E3 after the affinity purification. By IPTG induction, ca. 15 mg of human E3 (mature form) was obtained from 1L LB culture with overnight incubation at 25C. Over 98% of purity of E3 from one-step Ni-NTA agarose affinity purification was confirmed by SDS-PAGE analysis. For crystallization, E3 samples were prepared with and without His-tag. To minimize the aggregation of E3, apo- and holo- forms of E3s were tested, as well as a mutated E3. Dynamic light scattering measurements revealed that the E3 preparations without His-tag and substrate are highly monodispersive with regard to homodimers. Consequent crystallization trials of this E3 preparation led to single crystals of E3 grown by the vapor diffusion method. Crystals were obtained within a few days from solution containing poly (ethylene glycol) monomethyl ether 5000 as a precipitant. Autoindexing and integration of the X-ray diffraction data showed that E3 crystals belong to an orthorhombic system with unit cell parameters a-- 123. 1, b= 165.3 and c=214.3A. Further optimization of protein preparation and crystallization experiments for the structural determination will be discussed.

Hong, Y. S.↗
DOE OSTI2025

Multiframe X-ray diffraction on the OMEGA EP laser

A method of measuring multiple temporally resolved powder x-ray diffraction measurements during a single dynamic compression laser experiment has been demonstrated on the OMEGA EP laser. Up to four time-gated snapshots of the x-ray diffraction pattern are collected on an ultrafast x-ray framing camera with a 2θ scattering angle coverage of 48°–65° and 400-ps temporal resolution with the potential for 10°–160° and 200-ps resolution. X-ray diffraction snapshots capture the transformation to a high-pressure β phase in ramp-compressed Zr, constraining the atomic structure and pressure–density equation-of-state in a single shot. Here, this platform will be used to constrain transition pressures, understand the role of kinetics, and verify the existence of hysteresis and metastability on phase transformations at the lattice level under single-shot dynamic compression.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Investigating the Role π -Rich Solvents Play in the Growth of Cesium Lead Bromide Nanocrystals

In this report, the role that a high-boiling-point solvent type plays on the nucleation and growth, morphology, and crystal-phase transformation of cesium lead bromide nanocrystals (CsPbBr 3 ) is studied. The CsPbBr 3 products were compared between a one-pot growth mechanism at room temperature (RT) versus a hot-injection mechanism (HI) control using dibenzyl ether (DBE), diphenyl ether (DPE), dioctyl ether (DOE), or 1- octadecene (ODE). The coordination between these solvents and the PbBr 2 salt precursors resulted in different plumbate [PbSBr n ] 2−n precursors being formed. The S-to-Pb 2+ coordination within [PbSBr n ] 2−n was probed by UV−vis and solvent-phase 207 Pb NMR, both of which showed considerable coordination between [PbSBr n ] 2−n and the π-rich DBE and DPE, whose reactivity affected CsPbBr 3 growth. The effect was more pronounced for CsPbBr 3 prepared via RT, where the morphology was tunable, with π-rich solvents producing thin rod-like CsPbB r3 with a blue emission, compared to the green-emitting thicker platelets formed via HI. While XRD showed crystalline products for both RT and HI, with orthorhombic and cubic forms, respectively, the RT products had considerable surface defects, as was indicated by lower quantum yields, and to understand this the photoluminescent lifetimes were measured by time-correlated single photon counting.

207Pb NMR↗
NASA NTRS2011

CIRS-lite, a Fourier Transform Spectrometer for Low-Cost Planetary Missions

Passive spectroscopic remote sensing of planetary atmospheres and surfaces in the thermal infrared is a powerful tool for obtaining information about surface and atmospheric temperatures, composition, and dynamics (via the thermal wind equation). Due to its broad spectral coverage, the Fourier transform spectrometer (FTS) is particularly suited to the exploration and discovery of molecular species. NASA's Goddard Space Flight Center (GSFC) developed the CIRS (Composite Infrared Spectrometer) FTS for the NASA/ESA Cassini mission to the Saturnian system. CIRS observes Saturn, Titan, icy moons such as Enceladus, and the rings in thermal self-emission over the spectral range of 7 to 1000 ell11. CIRS has given us important new insights into stratospheric composition and jets on Jupiter and Saturn, the cryo-geyser and thermal stripes on Enceladus, and the winter polar vortex on Titan. CIRS has a mass of 43 kg, contrasted with the earlier GSFC FTS, pre-Voyager IRIS (14 kg). Future low-cost planetary missions will have very tight constraints on science payload mass, thus we must endeavor to return to IRIS-level mass while maintaining CIRS-level science capabilities ("do more with less"). CIRS-lite achieves this by pursuing: a) more sensitive infrared detectors (high Tc superconductor) to enable smaller optics. b) changed long wavelength limit from 1000 to 300 microns to reduce diffraction by smaller optics. c) CVD (chemical vapor deposition) diamond beam-splitter for broad spectral coverage. d) single FTS architecture instead of a dual FTS architecture. e) novel materials, such as single crystal silicon for the input telescope primary.

Brasunas, J.↗
DOE OSTI2023

Intercalation And High-Pressure Effects On Structural Phase Transitions In Layered As x P 1-x Alloys

This project was aimed at understanding the role of composition, intercalation, and high pressure on the structural evolution of black phosphorous (BP) and layered arsenic phosphorous alloys, As y P 1-y . Under normal conditions, BP is the most stable phase of phosphorous, known as the α-phase, characterized by an orthorhombic honeycomb puckered crystal structure with the Cmca space group. On the other hand, the most stable phase of arsenic is its β-phase, known as gray arsenic (g-As), which has a rhombohedral buckled layered crystal structure with the R3m space group. In a wide range of compositions (y < 0.83), the arsenic phosphorous alloys form the α-phase, known as black arsenic phosphorous (b-As y P 1-y ) with a similar structure to BP. The project was aimed at the synthesis of BP and b-As y P 1-y with different compositions and at studying the structural evolution of these materials during intercalation with alkali metal (especially Li), and under high-pressure conditions. The main goals were to gain a better understanding of these processes and structural changes taking place under these conditions. In particular, the project was aimed at addressing whether such conditions could induce a structural transition between the α- and β-phases. For this, a series of systematic in-situ studies were conducted, including electrochemical lithium intercalation in an in-situ electrochemical cell, and high-pressure experiments in a diamond anvil cell (DAC). Overall, both types of experiments have shown that above a certain composition-dependent threshold level of intercalation or high pressure, the system undergoes phase segregation rather than phase transition. Specifically, the segregation of the excess arsenic was observed, and a single-phase system of b-As y P 1-y transformed into a two-phase system consisting of b-As y P 1-y and g-As, through the following process: 1∗(b-As y P 1-y ) → 1∗(b As y-δ P 1-y ) + δ∗(g-As). Also, the study showed that intercalation and high-pressure are two competing rather than synergistic processes causing at least a partial cancelation of these two factors

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase transformations and thermal expansion coefficients of unirradiated U-X wt.% Zr (X = 6, 10, 20, 30) measured via neutron diffraction

This work characterizes the crystallographic evolution of unirradiated U-X wt.% Zr (X = 6, 10, 20, 30) while cooling from equilibration, single phase γ-U-Zr, at 900 °C to ambient temperature using time-of-flight neutron diffraction. The β-U phase was unobserved during cooling at 1 °C/min in all alloys. All alloys followed the phase transformation pathway of γ-U-Zr→γ-U-Zr+α-U→α-U +δ-UZr2 with an observed miscibility gap in γ-U-Zr. The α-U and δ-UZr2 transformation took place simultaneously in the U-30 wt.% Zr sample. These findings strengthen the need to re-approach the U-Zr phase diagram in entirety. Bulk volumetric CTEs agree well with published data, strengthening the quantification of lattice-specific CTEs reported in this study. A compositionally dependent discontinuity in thermal expansion, increasing in magnitude with decreasing U content, occurs during the γ-U-Zr→α-U+δ-UZr2 transformation. The γ-U-Zr lattice parameter was measured to have a compositional dependency.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Prediction of Solution Behavior via Calorimetric Measurements Allows for Detailed Elucidation of Polyoxometalate Transformation

The solution behavior of a polyoxometalate cluster, LiNa-U 24 Pp 12 (Li 24 Na 24 [(UO 2 O 2 ) 24 (P 2 O 7 ) 12 ]) that consists of 24 uranyl ions, peroxide groups, and 12 pyrophosphate linkers, was successfully predicted based on new thermodynamic results using a calorimetric method recently described for uranyl peroxide nanoclusters (UPCs), molybdenum blues, and molybdenum browns. The breakdown of LiNa-U 24 Pp 12 and formation of U 24 (Li 24 [UO 2 O 2 OH] 24 ) was monitored in situ via Raman spectroscopy using a custom heating apparatus. A combination of analytical techniques confirmed the simultaneous existence of U 24 Pp 12 and U 24 midway through the conversion process and U 24 as the single end product. The application of a molecular weight filter resulted in a complete and successful separation of UPCs from solution and, in conjunction with DOSY results, confirmed the presence of large intermediate cluster building blocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-pressure polymorphism in pyridine

Single crystals of the high-pressure phases II and III of pyridine have been obtained by in situ crystallization at 1.09 and 1.69 GPa, revealing the crystal structure of phase III for the first time using X-ray diffraction. Phase II crystallizes in P 2 1 2 1 2 1 with Z ′ = 1 and phase III in P 4 1 2 1 2 with Z ′ = ½. Neutron powder diffraction experiments using pyridine-d 5 establish approximate equations of state of both phases. The space group and unit-cell dimensions of phase III are similar to the structures of other simple compounds with C 2v molecular symmetry, and the phase becomes stable at high pressure because it is topologically close-packed, resulting in a lower molar volume than the topologically body-centred cubic phase II. Phases II and III have been observed previously by Raman spectroscopy, but have been mis-identified or inconsistently named. Raman spectra collected on the same samples as used in the X-ray experiments establish the vibrational characteristics of both phases unambiguously. The pyridine molecules interact in both phases through CH...π and CH...N interactions. The nature of individual contacts is preserved through the phase transition between phases III and II, which occurs on decompression. A combination of rigid-body symmetry mode analysis and density functional theory calculations enables the soft vibrational lattice mode which governs the transformation to be identified.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Fingerprinting Uranium Oxides with Electron Energy Loss Spectroscopy Supported by Theoretical Computations

Uranium oxides occur in a variety of phases that differ in crystal structure and uranium oxidation states. Electron energy loss spectroscopy (EELS) is one of the few techniques that has sufficient spatial resolution and sensitivity to electronic structure to distinguish amongst phases at the nanoscale. However, beam-sensitive materials such as uranium oxides are subject to spectral modification due to interactions with the electron beam. Therefore, theory support is essential to reliably exclude the impact of beam damage and generate true reference datasets. Here we use a comparison of theoretical and experimental spectra to probe the impact of beam damage on O K-edge and U N-edge (N6,7 and N4,5) EELS spectra of various single-valent and mixed-valence uranium oxide bulk phases. Using a low-dose experimental set-up, we show that the O K-edge theoretical spectra are in excellent agreement with experiment for both peak positions and relative intensities of respective peaks. In contrast, U N-edge features are less distinguishing due to the partially localized nature of the U 5f orbitals and overlapping multiplet and spin–orbit coupling effects. This work demonstrates that O K-edge EELS is sufficiently diagnostic to distinguish a wide range of uranium oxides and that the experimental approach used here minimizes beam damage and allows valence state discrimination across the U(IV), U(V) and U(VI) series. When combined with imaging modes available in electron mi-croscopy, the work enables detailed investigation and characterization of uranium redox transformations at the nanoscale.

Carbone, Jacopo↗
NASA NTRS2010

315mJ, 2-micrometers Double-Pulsed Coherent Differential Absorption Lidar Transmitter for Atmospheric CO2 Sensing

The design of a double pulsed, injection seeded, 2-micrometer compact coherent Differential absorption Lidar (DIAL) transmitter for CO2 sensing is presented. This system is hardened for ground and airborne applications. The design architecture includes three continuous wave lasers which provide controlled on and off line seeding, injection seeded power oscillator and a single amplifier operating in double pass configuration. As the derivative a coherent Doppler wind lidar, this instrument has the added benefit of providing wind information. The active laser material used for this application is a Ho: Tm:YLF crystal operates at the eye-safe wavelength. The 3-meter long folded ring resonator produces energy of 130-mJ (90/40) with a temporal pulse length around 220 nanoseconds and 530 nanosecond pulses for on and off lines respectively. The separation between the two pulses is on the order of 200 microseconds. The line width is in the order of 2.5MHz and the beam quality has an M(sup 2) of 1.1 times diffraction limited beam. A final output energy for a pair of both on and off pulses as high as 315 mJ (190/125) at a repetition rate of 10 Hz is achieved. The operating temperature is set around 20 C for the pump diode lasers and 10 C for the rod. Since the laser design has to meet high-energy as well as high beam quality requirements, close attention is paid to the laser head design to avoid thermal distortion in the rod. A side-pumped configuration is used and heat is removed uniformly by passing coolant through a tube slightly larger than the rod to reduce thermal gradient. This paper also discusses the advantage of using a long upper laser level life time laser crystal for DIAL application. In addition issues related to injection seeding with two different frequencies to achieve a transform limited line width will be presented.

Yu, Jirong↗
DOE OSTI2024

Structural, Electrical, and Optical Properties of Single-Walled Carbon Nanotubes Synthesized through Floating Catalyst Chemical Vapor Deposition

Single-walled carbon nanotube (SWCNT) thin films were synthesized by using a floating catalyst chemical vapor deposition (FCCVD) method with a low flow rate (200 sccm) of mixed gases (Ar and H 2 ). SWCNT thin films with different thicknesses can be prepared by controlling the collection time of the SWCNTs on membrane filters. Transmission electron microscopy (TEM) showed that the SWCNTs formed bundles and that they had an average diameter of 1.46 nm. The Raman spectra of the SWCNT films suggested that the synthesized SWCNTs were very well crystallized. Although the electrical properties of SWCNTs have been widely studied so far, the Hall effect of SWCNTs has not been fully studied to explore the electrical characteristics of SWCNT thin films. In this research, Hall effect measurements have been performed to investigate the important electrical characteristics of SWCNTs, such as their carrier mobility, carrier density, Hall coefficient, conductivity, and sheet resistance. The samples with transmittance between 95 and 43% showed a high carrier density of 10 21– 10 23 cm –3 . The SWCNTs were also treated using Brønsted acids (HCl, HNO 3 , H 2 SO 4 ) to enhance their electrical properties. After the acid treatments, the samples maintained their p-type nature. The carrier mobility and conductivity increased, and the sheet resistance decreased for all treated samples. The highest mobility of 1.5 cm 2 /Vs was obtained with the sulfuric acid treatment at 80 °C, while the highest conductivity (30,720 S/m) and lowest sheet resistance (43 ohm/square) were achieved with the nitric acid treatment at room temperature. Different functional groups were identified in our synthesized SWCNTs before and after the acid treatments using Fourier-Transform Infrared Spectroscopy (FTIR).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Upcycling Polycrystalline LiNi1/3Mn1/3Co1/3O2 to High-Performance Large-Grained LiNi0.6Mn0.2Co0.2O2 via Simplified Polyol-Mediated Recycling

The escalating demand for lithium-ion batteries (LIBs) necessitates advanced recycling strategies that can address both resource scarcity and environmental impact. While conventional hydrometallurgy shows promise, it is challenged by complexity, impurity management, and environmental footprint. Here, we report a strategic polyol-metallurgy recycling process that efficiently transforms spent polycrystalline LiNi1/3Mn1/3Co1/3O2 (NMC111) into high-performance large-grained LiNi0.6Mn0.2Co0.2O2 (NMC622), offering dual benefits of compositional upcycling and morphology upgradation. Our approach leverages a polyol system with meticulous control over nickel salt addition and the precipitation process. This yields upcycled cathode materials possessing excellent structural integrity, well-defined large-grained particles (5-10?..mu..m), and robust electrochemical performance, including a specific capacity of ~182 mAh g-1 at C/10 and 88.0% capacity retention after 100 cycles. This facile and multifunctional process provides an environmental-friendly pathway for advanced cathode recycling, significantly contributing to a circular economy for LIBs through precise control over critical material attributes.

25 ENERGY STORAGE↗
DOE OSTI2026

matsim-agents v1.0

matsim-agents is a multi-agent AI framework for atomistic materials simulation and discovery. It orchestrates large language models (LLMs), machine-learned interatomic potentials (MLIPs), and DFT codes into a single agentic loop running on laptops and DOE leadership-class supercomputers. MULTI-AGENT ORCHESTRATION A LangGraph state machine with three nodes: a Planner that converts a natural-language research objective into structured tasks; an Executor that dispatches atomistic tools and loops until the queue is empty; and an Analyst that summarizes results into a human-readable report. State is checkpointed after every step and human-in-the-loop gates can be inserted at any edge. HYPOTHESIS-DRIVEN DISCOVERY CHAT An interactive REPL (matsim-agents chat) that couples LLM dialogue with atomistic simulation. Chemical formulas are automatically detected in conversation turns and trigger a full crystal-phase exploration: structure generation → relaxation → stability scoring → result injection back into the conversation, creating a closed hypothesis-refinement loop. CRYSTAL PHASE ENUMERATION Given a composition, the phase explorer enumerates prototypes by stoichiometry: elemental (fcc/bcc/hcp/sc/diamond), binary 1:1 (rocksalt/CsCl/zincblende/ wurtzite/fluorite/rutile), ternary 1:1:3 (cubic perovskite), ternary 1:2:4 (perovskite + spinel), quaternary 1:1:2:6 (Fm-3m double perovskite). 2-D prototypes (graphene, h-BN, MoS2 2H/1T) and multilayer stacking are also supported via --include-2d and --num-layers. SUPERCELL GENERATION AND SITE DECORATION Auto-tiling to a minimum atom count (--min-atoms), explicit NxNxN tiling (--supercell), symmetry-distinct site decorations (--n-orderings), and isotropic lattice-scale sweeps (--lattice-scales) for volume bracketing. MLFF RELAXATION AND STABILITY SCORING HydraGNN (multi-headed GNN) drives structure relaxation via ASE with FIRE, BFGS, or BFGSLineSearch. Stability output: delta-E/atom ranking across phases and a max-residual-force dynamical-stability proxy. Other MLIPs (MACE, NequIP, Orb) can be plugged in through the same interface. DFT BACKENDS Quantum ESPRESSO pw.x and VASP 6.6 are first-class labellers. Both have validated GPU builds and SLURM/PBS launchers for three DOE platforms: Frontier (AMD MI250X, ROCm), Aurora (Intel PVC, oneAPI), Perlmutter (NVIDIA A100, CUDA). QE produces ~100 binaries (pw.x, ph.x, epw.x, ...). VASP supports scf, relax, vc-relax, and vc-relax-shape run types. ACTIVE-LEARNING LOOP matsim-agents al run CONFIG.yaml drives an iterative HydraGNN-DFT loop: MD generates candidates → ensemble/MC-dropout uncertainty selects the most informative → DFT labels them in parallel inside one allocation → dataset grows → HydraGNN retrains → repeat. DFT backend is a single YAML toggle (dft.backend: vasp | qe). LLM-generated seed structures are supported (no curated POSCAR library needed). Config uses ${VAR}, ${VAR:-default}, ${VAR:?msg} shell-style substitution for cross-user/cross-site portability. LLM BACKENDS Ollama (local, default), vLLM (HPC multi-GPU serving), OpenAI, Anthropic, HuggingFace Transformers+Accelerate. Selected at runtime via flag or env var with no code changes. HPC PORTABILITY Same Python entry points run on Frontier (ROCm 7.2), Aurora (oneAPI), and Perlmutter (CUDA 12). DFT and ML stacks are never co-loaded in the same shell; they couple through the scheduler and filesystem. Advanced multi-node launchers (serve, discovery-chat, single-relaxation, active-learning, QE warm-start) are provided for all three platforms. CODABENCH COMPETITION BUNDLE A self-contained benchmark: 159 atomistic test structures across 11 material classes, 5 tasks (formation energy, forces, ML relaxation, AI-DFT relaxation, phase stability ranking), public/private leaderboard split (30/70), and four ready-to-run baselines: MACE-MP-0, HydraGNN, UMA, AllScAIP.

Lupo Pasini, Massimiliano [Oak Ridge National Labo↗
DOE OSTI2026

Bypassing the yellow phase for extremely stable formamidinium lead iodide perovskite solar cells

INTRODUCTION Formamidinium lead iodide (FAPI) emerged as an ideal material for single-junction perovskite solar cells owing to its near optimal bandgap of 1.45 to 1.5 eV and outstanding thermal stability. However, the photoactive cubic α-phase (3C-FAPI) of FAPI is structurally unstable and undergoes a reconstructive phase transition to the nonperovskite yellow hexagonal δ-phase (2H-FAPI) at ambient temperature. The phase reconstruction from 3C-FAPI to 2H-FAPI could be prevented by alloying methylammonium (MA) or Cs or both at the A-site and Br at the halide site, but this limits long-term durability owing to phase segregation or materials instability. Addressing these challenges requires a rational design strategy to stabilize 3C-FAPI by restricting lattice reconstruction without compromising thermal stability. RATIONALE Two main strategies have emerged to improve the phase stability and film quality of FAPI. Here, the first is a lattice-templating approach, which enables the slow formation of perovskite but it eventually degrades through the formation of yellow phases. The second approach, which has been widely explored, involves additive engineering, using alkyl ammonium halide or mostly chloride-based additives, which provide better control over the crystallization route. However, the FAPI films fabricated using these additives are often alloyed and compromise long-term stability. Moreover, the exact role of Cl has been unclear and speculative, specifically when Cl-based additives are used. Even after using a high additive concentration, the incorporation of Cl in perovskite lattice is rare. RESULTS Guided by synergistic modeling and experimental studies, we developed a coadditive strategy using 15 mol % FACl and 0.5 mol % BA 2 PbI 4 perovskites in combination (where BA is butylammonium) to enable a highly oriented (100) Cl-doped FAPI film with exceptional durability. Synchrotron-based in situ wide-angle x-ray scattering revealed a favorable transition for the coadditive-treated FAPI (FAPI-CA) to the corner-sharing 3C black phase through a progressive transformation through the 2H, 4H, 6H, and 8H phases. Moreover, solid-state 35 Cl nuclear magnetic resonance (NMR) revealed Cl incorporation in the perovskite lattice and, as predicted by modeling, indicated that Cl plays a key role in altering the energetics of both the formation and degradation pathways. The Cl-doped perovskite can completely bypass the expected and energetically favorable degradation pathway via the yellow phase or the 2H-PbI 2 phase. Instead, it undergoes degradation only upon exposure to harsh conditions such as 15-sun illumination and 90°C through the energetically uphill 3R-PbI 2 phase path. A p-i-n device fabricated with FAPI-CA film demonstrated a power conversion efficiency (PCE) of 25.1% with an average of 24.1% (40 devices). The notable film stability translated to other devices and retained 98% of its initial PCE under open-circuit conditions at 85° ± 5°C for 1200 hours. CONCLUSION Our study highlights the decisive role of chloride in regulating both the formation and degradation pathways. This regulation is critical for creating a perovskite film with commercially relevant durability.

Garai, Rabindranath [Rice Univ., Houston, TX (Unit↗
DOE OSTI2025

FY24 Task 5: Leachate Disposition

Directly feeding sludge solids to the high-level waste (HLW) Waste Treatment Plant represents an alternative flowsheet seeking to initiate sludge processing as soon as possible. Key processing functions previously captured during baseline pretreatment operations include leaching and washing prior to solids concentration. These operations should be considered in the potential direct feed flowsheets to maximize waste feed loading, minimize HLW volume, and mitigate corrosion challenges associated with vitrification of high phosphate and fluoride concentrations. Additionally, single-shell tank (SST) retrievals and waste transfers to double-shell tanks (DSTs) in a direct feed flowsheet would likely also benefit from some level of leaching, washing, and solids concentration in order to reduce DST space and mission duration. These operations could occur in a new facility or potentially in available DSTs. If washing and leaching are utilized, an effective disposition pathway for the wash water and leachate solutions are needed. Three target species that benefit significantly from leaching and washing are phosphate, fluoride and aluminum. Phosphate (PO 4 3- ) and fluoride (F - ) can contribute substantially to the amount of carrier fluid needed for dissolution, and the resulting volume of liquid generated. Disposition of this retrieval solution should be evaluated in order to prevent crystallization of these anions throughout system processing. Since there is a high probability that any retrieval solutions will be at or near their PO 4 3- and F - solubility limits, evaporation or blending with a high Na supernate (>3.5 M) is not recommended for the wash water streams without a method to remove precipitants prior to solution disposal. Additionally, aluminum present in the southeast quadrant of the Hanford site represents roughly 60% of the waste solids in the initial processing tanks. These aluminum solids are in the form of gibbsite (Al(OH) 3 ) and can pose significant challenges for processing due to the fast-settling times and high solids loading associated with these materials. Easily remediated by caustic addition to the solids, these wash solutions could be processed through crystalline silicotitanate (CST) ion exchange columns to prepare the supernate solutions for disposition. The current target for feed conditions to the Low Activity Waste (LAW) melter are waste streams that contain nominally 5-6 M Na. Fractions within the tanks contain upwards of 0.2 M phosphate and fluoride in solution at 3.5 M Na. Concentrating these solutions above 5 M Na would result in an exceedance of the solubility limits, and potential for uncontrolled precipitation of the phosphate and fluoride crystal material. The resulting crystalline salt material is typically sodium fluoride phosphate, also referred to as natrophosphate (Na 7 FPO 4 ·19H 2 O). Salt phases are of importance in tank waste due to their chemical reactivity, which can result in precipitation, dissolution, or transformation, impacting any downstream processes (Bolling et al. 2020, Russell, Snow, and Peterson 2010). Salt generation and precipitation could pose challenges by causing system plugging and melter corrosion if left in the supernate stream, or limit sodium molarity of the supernate that would be accepted without incident in waste operations. To understand the impact of this salt generation, the crystallization of natrophosphate in multiple simulant feed matrices was studied to understand the implications of various tank waste supernate chemistries. Three matrices were examined: high PO 4 3- /low F - , low PO 4 3- /high F - , and an average matrix. Subsequent testing was performed with the average matrix with the inclusion of CsNO 3 , and a final run with the average matrix including CsNO 3 and a 137 Cs spike for tracer purposes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗