Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Demonstration of the Reproducibility Challenges in the Sintering Behavior of Lithium‐Stuffed Garnets in Scaling up Synthesis

Lithium-stuffed garnets, such as Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for next-generation solid-state batteries because of their high room-temperature ionic conductivity and chemical stability against lithium metal anodes, which are crucial for achieving higher energy density. However, realizing LLZO's potential in practical devices requires synthesis methods that can be scaled reliably to large batch sizes for manufacturing. Herein, we investigate the sintering reproducibility of LLZO synthesized at larger scales using ultrasonic spray pyrolysis, a cost-effective and scalable synthesis route. Two 100 g batches of Al-doped LLZO are prepared and their sintering behavior is examined in detail. Both Al-LLZO batches contain over 90 wt.% cubic-phase LLZO, and both batches exhibit room temperature conductivities greater than 1 × 10 −4 S cm −1 at a relative density above 0.8. However, variations in secondary phases and subtle differences in Al content lead to significant differences in densification and microstructure. These results demonstrate that LLZO's sintering behavior is highly sensitive to small changes in secondary phases and Al content, creating reproducibility challenges when moving from laboratory- to manufacturing-scale synthesis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hot Hydrogen Testing of W-Coated UN Kernels in a Mo30W Matrix

Ceramic uranium mononitride (UN) is being considered as a reactor fuel for nuclear thermal propulsion. To avoid or reduce the dissociation of UN at the high temperatures needed, embedding it in a metallic matrix (cermet) has been proposed. To assess the viability of this concept, hot hydrogen testing of tungsten-coated UN kernels embedded in a Mo-30 wt% W (Mo30W) alloy matrix has been performed at temperatures from 1800°C to 2300°C. Both the isolated kernels and kernels consolidated by spark plasma sintering in the Mo30W matrix were tested. In addition to direct observations and mass loss measurements, the samples were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS) after each run. The decomposition of UN started at 1800°C despite the coating and matrix, and increased at 2000°C. Uranium seeped through the tungsten grain boundaries of the coating at all temperatures. The consolidated sample expanded irregularly at 2000°C through the formation of voids, and SEM/EDS analysis showed uranium-containing veins in the matrix consisting of U 2 Mo according to the XRD data. The observed pore generation at 2000°C was explained by the formation of water vapor from residual oxides and diffused hydrogen. At 2200°C and above, both the kernels and the consolidated samples melted through the formation of uranium or low–melting point uranium-molybdenum alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

In situ Gas Cell TEM Investigation of Nanoporous and Zeolite-based Nanocatalysts

A crucial application of in situ transmission electron microscopy is the understanding of nanocatalysts and the effect of the environment on their structure. Pre-treatments, such as calcination or annealing, can dramatically impact the catalytic properties by modifying the morphology and composition of nanostructures. Zeolites and nanoporous structures are particularly sensitive to reactive environments as the porosity or the chemical state can substantially change during the interaction with gases at elevated temperatures.[1] For instance, it has been shown that heating in air causes redispersion of sintered Cu clusters on zeolite, improving the catalytic properties.[2] These observations are possible though innovative in situ TEM gas holders, where the samples are enclosed into a small cell with SiNx windows, isolating the reactive environment from the rest of the column. [3] Here, we present in situ gas cell experiments of sensitive nanoporous structure and zeolite-based nanocatalysts. Scanning transmission electron microscopy (STEM) and electron energy-loss spectroscopy were used to understand migration of Al during calcination. In situ diagnostics also help distinguish Al as Bronsted sites, extra-framework Lewis sites, or bulk alumina. More broadly, in situ gas-heating TEM experiments are useful to determine chemical changes and modification of morphology of sensitive nanocatalysts upon pre-treatment (Figure 1).[4] Detailed in situ STEM and energy-dispersive X-ray spectroscopy (EDS) demonstrated compositional changes in nanoporous CuAlTi structures for hydrogen-deuterium exchange (H2-D2) reaction. Coarsening due to annealing at high temperature, a necessary steps for the preparation of catalysts, can be reversed by applying a redox cycle. Using the wide range of gases and temperature, the diagnostics are helpful to derive fundamental understanding of these catalysts at the atomic scale and also provide general guidelines to improve their design.

Foucher, Alexandre [ORNL] (ORCID:0000000150424002)↗
DOE OSTI2020

Microwave-assisted ammonia synthesis over Ru/MgO catalysts at ambient pressure

Here, in this work, a fixed frequency (2.45 GHz) microwave (MW) was used to synthesis ammonia over Ru/MgO catalysts under ambient atmospheric pressure at 320 °C. The loading of Ru catalyst over MgO was varied at 4% and 10 wt %. The metal support interaction was found to play an important role not only catalytically but also altering the microwave-catalyst interaction affecting the ammonia formation rate. The higher metal loading (10 wt%) produced the most activity, stability, and energy efficiency. It was found the Ru was better dispersed at higher loading which decreased the sintering of the catalyst due to lower microwave energy needed to maintain the reaction temperature. Additional effects from the microwave can include enhanced electron movement and/or electric fields formed between the metal sites of the catalyst. The microwave reactor offers a quick on/off catalyst recovery, within 11 min, compared to thermal convectional Haber Bosch (HB) technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Tuning the Coordination Environment of Rh Single Atoms on Highly Dispersed Reducible Oxides for Enhanced Reverse Water-Gas Shift Performance

Controlling the dynamic mobility of catalyst surface active sites and their interactions with the surrounding environment is critical in generating active surfaces that directly influence the catalytic activity and selectivity. Here, we report a strategy for tailoring the dispersion and electronic environment of single atom Rh catalysts by decorating the alumina support with highly dispersed (HD) cerium and molybdenum oxides. The resulting catalysts exhibit markedly different behavior in the Reverse Water Gas Shift (RWGS) reaction. In particular, Rh/MoOx(HD)/Al2O3 maintains atomically dispersed Rh even at elevated temperatures (up to 400 °C), achieving CO selectivity of up to 100% and resists sintering via the formation of a newly developed structure featuring Rh single atoms embedded in MoOx clusters. In situ spectroscopy and microscopy analyses confirm the stabilization of Rh and the dynamic evolution of Rh–Mo coordination under reaction conditions. Our findings highlight the power of support modification in steering active site structure and activity, offering a pathway toward enhanced and tunable single atom catalysts for CO2 valorization.

CO selectivity↗
DOE OSTI2022

Designing Ceria/Alumina for Efficient Trapping of Platinum Single Atoms

Cerium oxide (ceria) has been shown to be very effective at trapping platinum atoms, due to formation of stable surface complexes at step edges, where coordinatively unsaturated cerium cations are present. But ceria loses its effectiveness when heated to high temperatures, due to loss of surface area and growth in particle size associated with sintering of the oxide. Being a rare-earth, and with limited supplies worldwide, it is important to develop methods to improve the effectiveness of ceria as a catalyst support. Here we explore the performance for trapping Pt atoms when the ceria is supported on a high surface area alumina carrier. This helps create a more sustainable catalyst formulation, especially if we can retain the high dispersion of Pt seen on ceria supports. For this work, we studied the atom trapping efficacy of ceria/alumina samples with increasing ceria content (8 wt% - 50%) and contrasted the behavior with pure ceria. Electron microscopy reveals that when dispersed on alumina, ceria is present in the form of crystalline nanoparticles as well as isolated cerium ions. These two forms of ceria differ markedly in their ability to trap Pt atoms. Atomically dispersed cerium is present in the form of Ce 3+ cations on alumina, however this form of ceria is not effective for trapping Pt atoms. Our results show that the atom trapped Pt resides primarily on crystalline ceria nanoparticles. CO oxidation was used as a probe reaction to evaluate the performance of these Pt AT /ceria-alumina catalysts. As a result, we conclude that over the range of ceria loadings we investigated, 50% ceria/alumina represents the optimal catalyst support for achieving high surface area and atom trapping efficiency while helping reduce the total ceria content in this catalyst system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of pretreatment conditions on Fe-ZSM-5 properties and performance for Fischer–Tropsch synthesis

Iron supported on ZSM-5 is a widely studied catalyst for Fischer–Tropsch synthesis (FTS). Iron is activated with H 2 , CO, or a mixture of CO and H 2 prior to FTS, resulting in phase transformations that make it challenging to understand structure–property relationships. Furthermore, in this work, we demonstrate that increasing the pretreatment temperature of Fe–Na-ZSM-5 reduces CO conversion irrespective of the reductant, but the product selectivity, iron particle size, composition, CO adsorption properties, and zeolite structure is dependent on both the pretreatment temperature and reductant. Pretreatment of Fe–Na-ZSM-5 in H 2 induces sintering of iron particles, increasing C 2 –C 4 olefins and C 5+ hydrocarbons selectivity from 19.0% and 14.0% at 350 °C to 28.2% and 25.4% at 770 °C, respectively. Conversely, CO pretreatment facilitates carbide formation, coke deposition, and CH 4 formation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of process route on powder three-dimensional-printing of metal powders

The purpose of this study is to investigate the effect of two unique processing routes (solvent jetting (SJ) and binder jetting (BJ)), on the green density of printed stainless steel 316L (SS316L) and Nickel (Ni) powders. In the SJ processing route, a solvent is jetted unto the powder/binder mixture to selectively activate the binder, layer by layer. In the BJ processing route, a solution of the binder mixture is jetted onto the powder bed to selectively bind powder particles. The effects of printing parameters such as layer height, roller speed, shaker speed and nozzle temperature on the green density of printed components are investigated and compared for both processing routes. Results show that layer height and nozzle temperature affect the relative density of the printed compact for both processing routes. Slightly higher relative densities were achieved via the SJ route, with the overall highest relative density being 42.7% at 100 µ m layer height and 70% nozzle temperature for the SS316L components and 43.7% at 150 µ m layer height and 90% nozzle temperature for the Ni components, respectively. Results also show an increase in the final sintered relative density with an increase in green (printed) relative density of the solvent jetted SS316L components, with the highest relative density being 87.2%. The paper studies the influence of printing parameters on the green density of printed SS316L and Ni samples in an unprecedented effort to provide a comparative understanding of the process-property relationships in BJ and SJ of SS316L and Ni components to the additive manufacturing research community.

Engineering↗
DOE OSTI2020

Atomic Layer Deposition for Enhanced Reactivity and Stability of Biomass Conversion Catalysts

Heterogeneous catalysts are an essential tool in the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions (e.g., high temperatures, acidity, oxidizing/reducing environments) of many key biomass conversion processes give rise to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Active site poisoning due to the relatively high sulfur content of most biomass feedstocks further compounds these durability problems. Next-generation catalysts must be developed to address these stability challenges. In this work, we used a scalable atomic layer deposition (ALD) process to modify conventional Pd-based hydrogenation catalysts to generate significant performance improvements. TiO2 ALD coatings were found to increase the activity of Pd/Al2O3 catalysts towards naphthalene hydrogenation; additionally, these coatings improved the catalyst's resistance to sulfur poisoning and thermal stability under oxidative calcination. Additional work in which Al2O3 ALD coatings were applied to Pd/TiO2 catalysts for muconic acid hydrogenation found similar stability benefits, including improved resistance to Pd leaching in the acidic environment. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of applying ALD coatings to supported Pd hydrogenation catalysts.

ALD↗
DOE OSTI2025

Machinable, high‐conductivity NaSICON through mitigation of humidity effects during solid‐state synthesis

The Na + super ion conductor (NaSICON, Na 1+x Zr 2 Si x P 3-x O 12 ) is a solid electrolyte well-known for fast, selective Na + transport at low temperatures, uniquely enabling sodium-based batteries. Producing high-quality NaSICON from solid-state methods, especially when cost-effective, potentially hygroscopic precursors are used, is not trivial. To understand and eliminate the influence of humidity during processing, a scheme was developed to reproducibly yield a high Na + conductivity (3.75 mS/cm at 25°C, 81.7 mS/cm at 150°C), high density (97%), and machinable NaSICON without the use of binders, sintering aids, or dopants. Controlled humidity studies over 20%–50% RH coupled with thermal, structural, and electrical analysis reveal that calcination temperatures < 1000°C leave NaSICON processing susceptible to water absorption at > 20% RH due to the presence of hygroscopic Na 3 PO 4 and Na 2 CO 3 during shaping, pressing, and sintering. Water absorption results in NaSICON with lower densities, machinability, and Na+ conductivity, due to impaired intergranular Na+ transport. At the other extreme, fully converting precursor to the NaSICON phase at 1230°C before pressing and sintering leads to poor conductivity and density. By calcining at 1000°C, excellent quality NaSICON may be produced under a range of laboratory environments, enabling low-cost production of high-conductivity, machinable NaSICON necessary the ever-growing energy storage market.

NaSICON↗
DOE OSTI2020

U 3 Si 2 and UO 2 composites densified by spark plasma sintering for accident-tolerant fuels

This work reports the synthesis and characterization of the U 3 Si 2 and UO 2 composites sintered by spark plasma sintering (SPS) with controlled microstructures for accident-tolerant fuel application. The U 3 Si 2 and UO 2 composites with different silicide and oxide ratios were synthesized by SPS at temperatures from 1000 to 1300 °C for 5 minutes. The microstructure and phase composition of the SPS densified composite fuels were characterized with scanning electron microscopy, X-ray diffraction (XRD), and energy dispersed spectroscopy (EDS). A systematic study of the thermal and mechanical properties was conducted using microhardness testing and laser flash apparatus, along with oxidation resistance measurements using thermogravimetric analysis (TGA). The results show that the synthesis of composite fuels can be achieved with a 90% theoretical density (TD) at 1000 °C and over 95% TD when sintered at 1300 °C. XRD and EDS results confirmed that the dominant phases in the composites are U 3 Si 2 and UO 2 . Improved physical density generally leads to improved hardness, fracture toughness, thermal diffusivity, and onset temperature during the oxidation process. U 3 Si 2 was found to play a dominant role in determining the mechanical and oxidation properties of the composite fuels, whereas UO 2 had a more important impact on controlling the thermal diffusivity of the composites. The composite with 50 wt% UO 2 sintered at 1300 °C displayed the onset oxidation temperature of 500 °C by dynamic oxidation testing using TGA at a ramp degree of 10 °C/min. The composite also achieved a high fracture toughness of ~3.5 MPa m ½ . Finally, these results highlight the potential of composite fuel forms densified by SPS with simultaneously enhanced fissile element density, fracture toughness, thermal transport properties, and oxidation resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Stabilization of Ultrasmall Platinum Nanoparticles by Nitrogen-Doped Carbon: Implications for Catalysis and Electrocatalysis

Heterogeneous materials comprising platinum nanoparticles on carbon supports have numerous applications including fuel cell electrodes and heterogeneous catalysts. The effective application of these materials for fuel cells and catalysis will be greatly advanced by the ability to control the oxidation and sintering of the nanoparticles by modifications of the carbon support. One attempt of such control has been doping carbon supports with nitrogen. Here, in this work, a cutting-edge, high-sensitivity, in situ XRD instrument, which allows observation of ultrasmall Pt nanoparticles, has been combined with in situ XPS to provide unprecedented clarity in the characterization of supported Pt nanoparticles in oxidizing and high-temperature environments. On a nitrogen-doped carbon support derived from poly-phenylporphyrin, Pt nanoparticles show increased stability to oxidation and thermal sintering. The enhanced Pt–support interaction arising from the N dopant versus the N-free carbon is manifested by (1) decreased initial Pt particle sizes, (2) small particle size at higher surface densities, (3) increased resistance of Pt nanoparticles to oxidation, (4) increased electron binding energy of Pt0, and (5) increased resistance of Pt nanoparticles to sintering. It is expected that the higher stability of Pt on NC will be manifested in higher activity in fuel cells and high-temperature catalytic reactions.

catalytic reactions↗
DOE OSTI2023

In situ probing of interfacial roughness and transient phases during ceramic cold sintering process

The ceramic cold sintering process (CSP) offers an eco-friendly approach to producing fully dense ceramics at low temperatures. However, an incomplete mechanistic understanding hinders its optimization and widespread adoption. In this study, we analyze the microstructural and structural changes in ZnO, a model CSP system, using in situ synchrotron-based high-energy small-angle X-ray scattering and X-ray diffraction techniques. Our results reveal the time evolution of ZnO particles' surface area and roughness, reflecting the dissolution and re precipitation processes that enable densification. The in situ measurements supply valuable kinetic data for these stages of CSP. Alongside microstructural changes and densification, we observed the evolution of secondary phases representing reaction products between ZnO and acetic acid, the solvent used. The initial ZnO/solvent mixture's dominant secondary phase is attributed to zinc acetate, which is gradually replaced by a zinc soap-type structure during CSP. This structure has a large (≈ 21 Å) lattice parameter and is assumed to have a layered nature. The formation of this soap phase, which is retained in the sintered product as an intergranular component, appears to be a signature of successful cold sintering as it facilitates mass transport, leading to densification. Here, our study underscores the potential of in situ synchrotron characterization for revealing microstructural and phase-evolution details during CSP. These findings, which would be challenging to obtain through ex situ measurements, provide crucial data to guide and validate theoretical models, ultimately enhancing CSP's effectiveness and adoption.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Final-stage densification kinetics of direct current–sinteredZrB2

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO2. Analysis was conducted on ZrB2 ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB2 ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to reach the final stage of sintering. The average grain size ranged from 1.0 to 14.7 μm. The activation energy was calculated from the slope of an Arrhenius plot that used the Kalish equation. The activation energy was 162 ± 34 kJ/mol, which is consistent with the activation energy for dislocation movement in ZrB2. The diffusion coefficients for dislocation motion that controls densification were 5.1 × 10−6 cm2/s at 1900°C and 5.1 × 10−5 cm2/s at 2100°C, as calculated from activation energy and average grain sizes. This study provides evidence that the dominant mechanism for final-stage sintering of ZrB2 ceramics is dislocation motion.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Metal hybridization in dilute-alloy catalysts promotes sintering resistance by decreasing surface mobility

Dilute-metal-alloy nanoparticles exhibit enhanced catalytic performance compared with monometallic nanoparticles for many reactions. Anecdotal reports indicate that very dilute alloying can also slow the sintering rates of supported nanoparticles, although this has not been rigorously assessed and cannot be explained using bulk descriptors such as metal melting temperature. Here, in this study, we utilize methanol synthesis reactivity, microscopy and in situ spectroscopy measurements to demonstrate that 1 atom% Pt addition to ~1–2-nm-diameter Cu (Pt 1 Cu 100 ) nanoparticles supported on SiO 2 dramatically decreases their sintering rates. Minimal sintering of Pt 1 Cu 100 nanoparticles is observed during aging in H 2 up to 700 °C versus 500 °C for Cu nanoparticles. Scanning tunnelling microscopy reveals that the addition of 0.01 monolayer of Pt to a Cu(110) surface decreases the detachment rate of undercoordinated atoms, demonstrating that dilute dopants can locally decrease the rate of the first step in nanoparticle sintering. Density functional theory calculations quantify the stabilization and predict other sinter-resistant dilute alloys. We find that the degree of host–dopant d-state hybridization correlates with decreased surface mobility, providing a mechanistic framework for designing sinter-resistant catalysts.

Finzel, Jordan [Univ. of California, Santa Barbara↗
DOE OSTI2023

Importance of the Heat Treatment Scheme on Self-Reducing Reactive Silver Inks

Self-reducing reactive silver inks can print high-quality silver at reasonable temperatures. While numerous studies have explored the impact of processing temperature on electrical properties, the role of the heat treatment scheme has not yet been studied. Common heat treatment schemes include printing and drying inks at room temperature before heat treatment, performing heat treatments while the inks are still wet, and directly printing the inks onto heated substrates. Each scheme generates distinct heat transfer and mass transport kinetics that can affect the silver morphology and electrical properties. However, to date, the impact of different schemes has not been systematically investigated. To address this knowledge gap, this work investigates how different heat treatment schemes impact metal formation, sintering, and the resultant electrical properties of printed self-reducing reactive silver inks. Heat treatment on room-temperature dried inks and wet inks, with top-down (oven) and bottom-up (hot plate) heating sources, were compared. Inks dried at room temperature resulted in extremely porous films that required high heat treatment temperatures (>100 °C) for silver densification. However, these dried films could only densify locally, and their high initial porosities resulted in voids and high resistances (~0.6 Ω mm –1 ) even after heat treatments above 300 °C. Inks that were wet during heat treatment showed moderate improvements in electrical properties with resistances on the order of 0.4 Ω mm –1 at heat treatments of 250 °C. Printing reactive inks directly onto heated substrates yielded the best low-temperature results, with 0.46 Ω mm –1 (5.5 × bulk silver) line resistances achieved at only 90 °C. Overall, this work’s experimental results provide detailed insights into why printing onto a heated substrate results in superior electrical performance compared to more common heat treatment schemes. Additionally, controlling where the precipitation reaction occurs is critical to controlling the film morphology and properties. As a result, this work shows that even an ammonia-based silver reactive ink can achieve good, low-temperature electrical properties with the proper heat treatment scheme.

14 SOLAR ENERGY↗
DOE OSTI2024

Influence of elevated temperature and oxygen on the capture of radioactive iodine by silver functionalized silica aerogel

Reprocessing is considered a competent strategy for spent nuclear fuel management, yet radioiodine ( 129 I) is emitted in reprocessing off-gas as a hazardous byproduct. Silver functionalized silica aerogel (Ag 0 -aerogel), a promising iodine capture material, experiences a reduction in its capacity after prolonged exposure to off-gas components at elevated temperatures, a phenomenon termed as aging. To fully understand this process, we isolated the contribution of each aging factor, exposing Ag 0 -aerogel samples to N 2 and dry air gas streams, respectively, at 150 °C for different time periods. Aged samples were loaded with I 2 to examine the capacity change and comprehensively characterized to investigate the evolution of their properties. Results show that temperature alone did not alter Ag 0 -aerogel's capacity but triggered Ag 0 nanoparticles sintering and generated organic sulfur species. The presence of O 2 reduced the capacity by ~20 %, causing (i) formation of silver sulfide (Ag 2 S) crystals and (ii) oxidation of Ag-thiolate (Ag-S-r) to Ag sulfonate (Ag-SO 3 -r). Given that Ag 2 S readily adsorbs I 2 , the formation of Ag-SO 3 -r is the major inhibitor for iodine adsorption. This hypothesis was supported by density functional theory (DFT) simulations. These findings unraveled key mechanisms of Ag 0 -aerogel aging, which are useful in the development of materials that withstand realistic spent-nuclear-fuel-reprocessing off-gas conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

High pressure neutron diffraction on WAND 2 with a Paris-Edinburgh press

The Paris-Edinburgh press is a widely available, highly adaptable pressure cell commonly used while collecting neutron scattering data. Here, we detail the use of the VX3 and VX5 Paris-Edinburgh presses on the Wide-Angle Neutron Diffractometer (WAND 2 ) at the High Flux Isotope Reactor at Oak Ridge National Laboratory. We first give a detailed overview of the instrument setup and alignment capabilities used at WAND 2 . We then demonstrate the high pressure capabilities through three examples. In this work, the first example focuses on diffraction data obtained from a lithium-diamond mixture to 10 GPa with the use of single toroidal cubic boron nitride anvils. Other examples include the room temperature compressions of germanium (up to 16 GPa) and the mineral malachite with double toroidal sintered diamond anvils. This work thereby represents the first studies above 10 GPa at the High Flux Isotope Reactor and opens the door for future user experiments at these elevated pressures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗