Search NASA⌕ Search

SEARCH · Search NASA

Results for “siting considerations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Emissions of N2O, CH4 and CO2 from tropical forest soils

Emissions of nitrous oxide, methane, and carbon dioxide were measured at diverse locations in tropical forests of Brazil, Ecuador, and Puerto Rico using a static open chamber technique. Mean fluxes to the atmosphere were 1.7 x 10 to the 10th, -0.7 x 10 to the 10th, and 1.5 x 10 to the 14th molecules/sq cm per s for N2O, CH4, and CO2, respectively. The data indicate that tropical forests contribute a significant fraction of the global source for atmospheric N2O, about 40 percent of the current source, and possibly 75 percent of the preindustrial source. Methane is consumed by soils on average, but the sink is an insignificant part (less than 5 percent) of the atmospheric cycle for the gas. Emissions of CO2 from forest soils are higher at equatorial sites than at middle or high latitudes, as expected from ecological considerations. Soils emit CO2 at rates more than twice as large as the rate of carbon infall in litter; hence much of the emitted CO2 must arise from root metabolism.

Keller, Michael↗
NASA NTRS1995

Direct Comparison of GPS and VLBI Velocity Estimates

Considerable effort has been made to collocate permanent GPS and VLBI sites for comparison. The global GPS solution is derived from daily measurements spanning four years while the VLBI solution is based on monthly measurements spanning more than 10 years. Current WRMS agreement of velocities is 3-5 mm/yr for horizontal rates and 6-10 mm/yr for vertical rates. Comparison of velocities is limited by the time span of GPS data. Positions agree at the level of 1-2 cm and their comparison is limited by the quality of the site ties. Best and worst agreement will be discussed along with possible sources of systematic error.

GPS VLBI↗
NASA NTRS2011

Mission Implementation Constraints on Planetary Muon Radiography

Cost: Use heritage hardware, especially use a tested landing system to reduce cost (Phoenix or MSL EDL stage). The sky crane technology delivers higher mass to the surface and enables reaching targets at higher elevation, but at a higher mission cost. Rover vs. Stationary Lander: Rover-mounted instrument enables tomography, but the increased weight of the rover reduces the allowable payload weight. Mass is the critical design constraint for an instrument for a planetary mission. Many factors that are minor factors or do not enter into design considerations for terrestrial operation are important for a planetary application. (Landing site, diurnal temperature variation, instrument portability, shock/vibration)

entry, descent, and landing (EDL)↗
DOE OSTI2022

Fetch-trap Pairs: Exploring definition of carbon storage prospects to increase capacity and flexibility in areas with competing uses

As CCS grows beyond isolated first-mover projects, the question of how to identify potential storage sites (prospects) is key to siting projects amidst the constraints of neighboring storage projects, hydrocarbon fields and other considerations. To date, prospects have been defined either by the extent of a buoyant trap or by the predicted maximum extent of the CO 2 or pressure plume. Both approaches have worked, but they may struggle in places like the Gulf of Mexico where complex geologic structure can invalidate simple assumptions of radial plume spread and buoyant traps are commonly unattractive due to numerous legacy well penetrations. Here, we propose identifying prospective storage sites by fetch area (drainage cell) rather than by buoyant closure alone. Doing so offers 1) greater freedom in siting injectors to avoid surface and subsurface constraints, including legacy wells that tend to cluster on structural high; and 2) a coherent flow regime in which buoyancy drives all injected CO 2 toward a common high. This strategy gives space to dissipate injection pressure and minimize the number of legacy wells needing review. It may also offer 1) better injectivity by bringing synclines and associated channel axes into play; and 2) potentially improved capacity by tapping a larger rock volume and taking advantage of migration losses.

58 GEOSCIENCES↗
DOE OSTI2022

High-Platinum-Content Catalysts on Atomically Dispersed and Nitrogen Coordinated Single Manganese Site Carbons for Heavy-Duty Fuel Cells

Fuel cells for heavy-duty vehicles (HDVs) have attracted considerable attention because of their unique scalability, better fuel economy, the less demand for hydrogen refilling infrastructure. However, the potential application requires more stringent fuel cell durability up to 25,000 h. Membrane electrode assemblies (MEAs) made from platinum group metal (PGM) catalyst with relatively high loading 0.3 mgPt cm –2 play a crucial role in ensuring high-power and long-term durability. Integrating fine PGM nanoparticles and robust carbon support with strengthened interactions is critical for improving MEA performance and durability. Herein, a unique atomically dispersed and nitrogen coordinated single Mn site-rich carbon (M–N–C) support was developed for high content (40 wt%) platinum catalysts for the oxygen reduction reaction (ORR) cathode with reduced thickness. Compared with two controls studied in this work (e.g., a porous graphitic carbon-supported Pt and a commercial TKK Pt/C catalysts), the Pt (40 wt%)/Mn–N–C catalyst exhibited much enhanced catalytic activity and stability for the ORR in both aqueous acidic electrolyte and polymer electrolyte-based MEA. Here, we carefully elucidated the—role of the Mn–N–C support in promoting Pt catalyst concerning its high surface area, partially graphitic structure, and nitrogen dopants, providing better Pt nanoparticle dispersion, and strengthened interactions between Pt and carbon. Consequently, the MEA from the Pt (40 wt%)/Mn–N–C catalyst generated a 1.61 A cm –2 at 0.7 V based on HDV conditions (0.2 mgPt cm –2 and 250 kPa air). More importantly, the MEA is highly durable and can retain 1.31 A cm –2 at 0.7 V after 30,000 voltage cycles (~19% loss), surpassing the commercial Pt/C catalyst (loss of ~56%). Therefore, the Mn–N–C carbon-supported Pt catalyst holds a great promise to meet the challenging DOE target (1.07 A cm –2 at 0.7 V after 150,000 cycles) for HDVs.

25 ENERGY STORAGE↗
DOE OSTI2025

Spent Nuclear Fuel Receipt Rate Analysis within an Integrated Waste Manage-ment System Architecture that Includes Consolidated Interim Storage

A key parameter in analyzing the performance of an integrated waste management system (IWMS) architecture for the disposition of spent nuclear fuel (SNF) is the SNF receipt rate from reactor and other custodian sites. The introduction of one or more federal consolidated interim storage facilities (CISFs) into the IWMS architecture can enable the receipt rate profile as a function of time to be accelerated relative to system architectures without a CISF. The question then arises as to what an optimal SNF receipt rate profile for an IWMS architecture might be in view of practical constraints and desired system performance attributes and associated metrics. This paper describes a sensitivity study on SNF receipt rates and the associated results for a selected set of IWMS scenarios aimed an in-forming near-term planning for interim storage capabilities and transportation assets. Two different strategies are compared, one that fills an initial CISF quickly and then idles the transportation system while a disposal system is prepared, and a second strategy that aims to provide a more continuous use of transportation assets and receipt capabilities at the IWMS while the disposal system is readied for SNF receipt. Cost considerations and other factors such as impact on timing of clearing reactor sites of SNF, efficient use of capital assets, and other metrics, including those which may be important to a CISF host community, are examined. Based on the analysis, an initial approach is presented targeting a continuous receipt strategy while having the flexibility to step up receipt capabilities to a reasonable degree when needed and beneficial within overall system constraints.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

QM Investigation of Rare Earth Ion Interactions with First Hydration Shell Waters and Protein-Based Coordination Models

Here, conventional methods for extracting rare earth metals (REMs) from mined mineral ores are inefficient, expensive, and environmentally damaging. Recent discovery of lanmodulin (LanM), a protein that coordinates REMs with high-affinity and selectivity over competing ions, provides inspiration for new REM refinement methods. Here, we used quantum mechanical (QM) methods to investigate trivalent lanthanide cation (Ln 3+ ) interactions with coordination systems representing bulk solvent water and protein binding sites. Energy decomposition analysis (EDA) showed differences in the energetic components of Ln 3+ interaction with representatives of solvent (water, H 2 O) and protein binding sites (acetate, CH 3 COO – ), highlighting the importance of accurate description of electrostatics and polarization in computational modeling of REM interactions with biological and bioinspired molecules. Relative binding free energies were obtained for Ln 3+ with coordination complexes originating from binding sites in PDB structures of a lanthanum binding peptide (PDB entry 7CCO) and LanM, with explicit consideration of the first hydration shell waters, according to quasi-chemical theory (QCT). Beyond the first shell, the bulk solvent environment was represented with an implicit continuum model. Ln 3+ interactions with (H 2 O) 9 and both binding site models became more favorable, moving down the periodic series. This trend was more pronounced with the protein binding site models than with water, resulting in affinity increasing with periodic number, except for the last REM, Lu 3+ , which bound less favorably than the preceding element, Yb 3+ . Using the truncated 7CCO binding site model, the magnitude and trend of the experimental Ln 3+ relative binding free energies for the whole 7CCO peptide were reproduced. Conversely, the previously reported experimental data for LanM show a preference for the earlier lanthanides; this is likely due to longer-range interactions and cooperative effects, which are not represented by the reduced models. Using the truncated 7CCO binding site model, the magnitude and trend of the experimental Ln 3+ relative binding free energies for the whole 7CCO peptide were reproduced. In contrast to the previously reported experimental data for LanM, the peptide preferentially binds the earlier lanthanides. This difference likely arises due to longer-range interactions and cooperative effects not represented by the peptide. Further investigation of Ln 3+ interactions with whole proteins using polarizable molecular mechanics models with explicit solvent is warranted to understand the influence of longer-ranged interactions, cooperativity, and bulk solvent. Nevertheless, the present work provides new insights into Ln 3+ interactions with biomolecules and presents an effective computational platform for designing specific single-site REM binding peptides more efficiently.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Exploring the role of biotic factors in regulating the spatial variability in land surface phenology across four temperate forest sites

Here, land surface phenology (LSP), the characterization of plant phenology with satellite data, is essential for understanding the effects of climate change on ecosystem functions. Considerable LSP variation is observed within local landscapes, and the role of biotic factors in regulating such variation remains underexplored. In this study, we selected four National Ecological Observatory Network terrestrial sites with minor topographic relief to investigate how biotic factors regulate intra-site LSP variability. We utilized plant functional type (PFT) maps, functional traits, and LSP data to assess the explanatory power of biotic factors for the start and end of season (SOS and EOS) variability. Our results indicate that PFTs alone explain only 0.8–23.4% of intra-site SOS and EOS variation, whereas including functional traits significantly improves explanatory power, with cross-validation correlations ranging from 0.50 to 0.85. While functional traits exhibited diverse effects on SOS and EOS across different sites, traits related to competitive ability and productivity were important for explaining both SOS and EOS variation at these sites. These findings reveal that plants exhibit diverse phenological responses to comparable environmental conditions, and functional traits significantly contribute to intra-site LSP variability, highlighting the importance of intrinsic biotic properties in regulating plant phenology.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Hanford Site Composite Analysis: Dose Sensitivity Analyses

This environmental calculation file (ECF) documents the methodologies, assumptions, and results of five analyses that evaluate parameter changes to the revised Hanford Site Composite Analysis (CA) (DOE-RL-2019-52, Composite Analysis for Low-Level Waste Disposal in the Hanford Site Central Plateau). Specifically, this ECF describes the impact on total dose and analyte-specific doses for five sensitivity cases where changes to the following exposure-related parameters were implemented – (1) inventory, (2) recharge rate, (3) external dose conversion factors (DCFs) based on Federal Guidance Report (FGR) No. 15 in (EPA-402-R-19-002, Federal Guidance Report No. 15, External Exposure to Radionuclides in Air, Water, and Soil) instead of FGR No. 12 (EPA 402-R-93-081, Federal Guidance Report No. 12, External Exposure to Radionuclides in Air, Water, and Soil) for groundwater pathway scenario; (4) use of mean instead of 95th percentile intake assumptions for groundwater pathway scenario; and (5) consideration of limited sources based on U.S. Department of Energy (DOE) owned waste sites regulated under DOE O 435.1, Radioactive Waste Management. It should be noted that dose assessments for both base and sensitivity cases are based on the all-pathways representative person groundwater exposure scenario presented in DOE/RL-2022-52, Composite Analysis for Low-Level Waste Disposal in the Hanford Site Central Plateau.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1998

Resource Utilization and Site Selection for a Self-Sufficient Martian Outpost

As a planet with striking similarities to Earth, Mars is an important focus for scientific research aimed at understanding the processes of planetary evolution and the formation of our solar system. Fortunately, Mars is also a planet with abundant natural resources, including assessible materials that can be used to support human life and to sustain a self-sufficient martian outpost. Resources required include water, breathable air, food, shelter, energy, and fuel. Through a mission design based on in situ resource development, we can establish a permanent outpost on Mars beginning with the first manned mission. This paper examines the potential for supporting the first manned mission with the objective of achieving self-sufficiency through well-understood resource development and a program of rigorous scientific research aimed at extending that capability. We examine the potential for initially extracting critical resources from the martian environment, and discuss the scientific investigations required to identify additional resources in the atmosphere, on the surface, and within the subsurface. We also discuss our current state of knowledge of Mars, technical considerations of resource utilization, and using unmanned missions' data for selecting an optimal site. The primary goal of achieving self-sufficiency on Mars would accelerate the development of human colonization beyond Earth, while providing a robust and permanent martian base from which humans can explore and conduct long-term research on planetary evolution, the solar system, and life itself.

Barker, Donald↗
NASA NTRS2008

Emergency Landing Planning for Damaged Aircraft

Considerable progress has been made over the last 15 years on building adaptive control systems to assist pilots in flying damaged aircraft. Once a pilot has regained control of a damaged aircraft, the next problem is to determine the best site for an emergency landing. In general, the decision depends on many factors including the actual control envelope of the aircraft, distance to the site, weather en route, characteristics of the approach path, characteristics of the runway or landing site, and emergency facilities at the site. All of these influence the risk to the aircraft, to the passengers and crew, and to people and property on the ground. We describe an ongoing project to build and demonstrate an emergency landing planner that takes these various factors into consideration and proposes possible routes and landing sites to the pilot, ordering them according to estimated risk. We give an overview of the system architecture and input data, describe our preliminary modeling of risk, and describe how we search the space of landing sites and routes.

Meuleau, Nicolas↗
NASA NTRS1998

Potential Mars Surveyor 2001 Landing Sites: Low-Elevation Cratered "Highlands" in Central and Eastern Sinus Meridiani and Near Amenthes Fossae

The main scientific goal for the Mars Surveyor Program 2001 (MSP 01) landed mission is to collect and characterize 91 rock and 13 soil core samples using an integrated instrument suite onboard the Athena Rover. If possible, these samples will be retrieved and returned to Earth via a MSP 05 or MSP 07 mission. Preliminary engineering constraints for the MSP 01 landing site call for a location that lies between 15 S and 30 N, and below about 2 km elevation (based on Viking-era topography). Desirable landing sites for MSP 01 are to be located "in the ancient highlands where the environmental conditions may have been favorable to the preservation of evidence of possible prebiotic or biotic processes including the emergence (and, potentially, the persistence) of life". We interpret this to mean that the desirable sites include those that have evidence of aqueous sediments that might have been deposited during the Noachian and/or Hesperian Epochs of Mars' history. In addition to the search for subaqueous sedimentary deposits, we took into consideration the fact that the rover, Athena, will need to be able to access these materials. Thus, a site where aeolian deflation has occurred might be desirable because it might expose, in situ, layered sedimentary deposits. Deflated areas, of course, might include potential landing hazards in the form of meterscale buttes and mesas (e.g., Christmas Lake Valley, OR), thus careful study of such sites with high resolution images will be required before a decision is made to land. We have been examining three regions that have potential to be considered for MSP 01 landing sites. This work is based on Viking (VIS, IRTM) and Phobos 2 (Termoskan) observations and should be regarded as preliminary because we believe that the final site selection should also be based upon analysis of Mars Global Surveyor observations that help constrain mineralogy (TES) and local geomorphology (MOC, MOLA). (1) Eastern Sinus Meridiani Region (proposed by K. S. Edgett) Sinus Meridiani is a persistent low-albedo (< 0. 16) region on the martian equator that has been recognized for about 400 years. All of Sinus Meridiani is below the 2 km elevation constraint for MSP 01. The region includes cratered highlands, valley networks, aeolian dunes, and possible aqueous sedimentary deposits. The landing site study region is located in the eastern portion of Sinus Meridiani. It is bounded by latitudes 10 S to 2 N, longitudes 355 W to 345 W, and the elevations are mostly 1-2 km. The center of this area contains a medium-albedo (0.19-0.21), relatively smooth-surfaced deposit that was suggested by Rice to be a lacustrine deposit. Several potential landing areas can be suggested within this region. Based on Viking and Phobos 2 data, the favored sites so far are centered at 7.6 S, 346.9 W and 0.8 S, 349 W. Thermal inertias are 3.2-7.0 x 10(exp -3) cal /sq cm s(exp -0.5)/K; and rock abundances are around 2-6%. The site at 7.6 S, 346.9 W is at the southern end of the smooth, medium-albedo unit that might have a lacustrine origin. At this location, numerous channels appear to have drained toward the smooth unit. Viking images from orbit 747A show this area at about 15 m/pixel ground resolution. The images reveal that aeolian deflation has occurred along the deposit's margins. Bright (i.e., albedo >= 0.21) aeolian dunes are present on the channel floors and in some of the depressions on the smooth unit. The bright, apparently active dunes might consist of material (perhaps lakedeposited sands) that has been eroded from the smooth unit. The site at approximately 0.8 S, 349 W is selected because it offers an opportunity to solve a long-standing puzzle about Mars remote sensing. There are three main "color" units on Mars: "dark red, dark gray, and bright red". This landing site would allow the Athena rover an opportunity to investigate all three materials within close proximity (the best place on Mars to do so). There are no high resolution (better than 100 m/pixel) Viking or Mariner images of this site. (2) Central Sinus Meridiani Region (proposed by K. S. Edgett and T. J. Parker) Central Sinus Meridiani is characterized by two types of surfaces [4]. One is like typical martian cratered highlands elsewhere- there are old valley networks and old impact craters. The other is relatively smooth and flat. These two units are in contact around 3.1 S between 5 W and 4 E longitudes. Valley networks- including one at 6'S, 358 W that rivals the Grand Canyon of Arizona- once drained toward the smooth unit. Edgett and Parker [4] proposed that the smooth unit might consist of sediments laid down in a large Noachian-aged sea/ocean that would have covered much of the northern hemisphere. Schultz and Lutz [I I I suggested that it is a paleopolar layered deposit. Regardless, the smooth unit where it contacts the cratered terrain would make an excellent site for Athena rover to investigate. The site is best seen in Viking high resolution images from orbits 408B (about 30 m/pixel) and 746A (about 12 m/pixel). These images suggest that aeolian deflation has occurred along the margin of the smooth unit, and this deflation has exposed horizontal larrs of material. The elevation is about 0.5 km; thermal inertias are 6.5-8.0 x 10(exp -3) cal /sq cm s(exp -0.5) / K; rock abundances are 2-4%; and the surface is probably sandy with dark drifts and ripples but almost no actual dunes. We suggest a landing around 3.2 S, 3.0 W would test the aqueous sediment hypothesis and provide a potentially smooth surface on which to land. (3) Amenthes Fossae Region (proposed by S. N. Huntwork and K. S. Edgett) The Amenthes Fossae are a series of graben/fissures that are circumferential to the southeast side of Isidis Planitia. These fissures cross a variety of ancient, heavily cratered Noachian terrain and younger, Hesperian and Amazonian terrain. We focused our search on a region 0-15 N, 250 - 270 W. Elevations are -0.5 to 2 km. Depending upon whether Isidis Planitia was ever a water-rich environment, this region might have been influenced by aqueous sedimentation. Valley networks are common, and they drained toward the north and northwest. We focused our work on a set of Viking orbiter high-resolution images, 719A 1-48. These have resolutions 16-24 rri/pixel. We examined images 20-23, centered at 2 N, 258 W. This site, on the plains just southwest of a 42 km-diameter crater, includes a valley network channel, a relatively young crater ejecta deposit, a few buttes composed of presumably ancient, Noachian bedrock, and a "plains" unit. The plains might make an ideal landing surface, except for the presence of some fine-scale ridges (oriented approximately N-S). The ridges are probably yardangs, thus this site offers a place where aeolian deflation has probably exposed some of the layered rock units that comprise the "plains". Thermal inertias are 7.9-8.3 x 10(exp -3) cal/sq cm s(exp -0.5) /K and rock abundances are 10-15%. A rover traverse might include the opportunity to go down to the floor (and sample along the walls) of the valley network channel at 2 N 258.1 W.

Edgett, K. S.↗
NASA NTRS1965

LEM piloted control considerations.

LEM mission and pilot role in spacecraft control including guidance and control systems, retromaneuvering, landing-site inspection, etc

GUIDANCE AND CONTROL↗
NASA NTRS1993

Visual display aid for orbital maneuvering - Design considerations

This paper describes the development of an interactive proximity operations planning system that allows on-site planning of fuel-efficient multiburn maneuvers in a potential multispacecraft environment. Although this display system most directly assists planning by providing visual feedback to aid visualization of the trajectories and constraints, its most significant features include: (1) the use of an 'inverse dynamics' algorithm that removes control nonlinearities facing the operator, and (2) a trajectory planning technique that separates, through a 'geometric spreadsheet', the normally coupled complex problems of planning orbital maneuvers and allows solution by an iterative sequence of simple independent actions. The visual feedback of trajectory shapes and operational constraints, provided by user-transparent and continuously active background computations, allows the operator to make fast, iterative design changes that rapidly converge to fuel-efficient solutions. The planning tool provides an example of operator-assisted optimization of nonlinear cost functions.

Grunwald, Arthur J.↗
DOE OSTI2021

Hybrid Double Perovskite Containing Helium: [He 2 ][CaZr]F 6

Perovskites are of great technological and geological importance, in large part, due to their considerable compositional and structural flexibility. However, the formation of perovskites with neutral species on their A-sites is very unusual. The formation, phase transitions and properties of [He 2 ][CaZr]F 6 , which is the first noble gas containing perovskite to be made, are reported. It is likely that a large family of related materials can also be prepared. On compression in neon, the negative thermal expansion (NTE) material CaZrF 6 amorphizes at ~ 0. 5 GPa. However, on compression in helium at room temperature, gas is inserted into the structure to form a perovskite with helium on the A-site. This suppresses the amorphization until > 3 GPa. Volume versus pressure and Raman measurements suggest that filling of the A-site, to give [He 2 ][CaZr]F 6 , is complete at > 1 GPa. The presence of helium on the A-site in this perovskite leads to a reduction in the magnitude of negative thermal expansion when compared to the parent phase CaZrF 6 , likely due to steric impediment of the transverse vibrational motion of fluoride. The helium also leads to considerable stiffening of the structure. At room temperature and ~2.5 GPa, the helium containing hybrid perovskite has a bulk modulus of ~ 47 GPa, whereas CaZrF 6 has a bulk modulus of ~ 40 GPa at ambient. At 15 K, the cubic perovskite [He 2 ][CaZr]F 6 undergoes a structural phase transition, that likely involves a cooperative tilting of framework octahedra to give a lower-symmetry phase, which is tentatively assigned as tetragonal.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Confronting the water potential information gap

Water potential directly controls the function of leaves, roots and microbes, and gradients in water potential drive water flows throughout the soil–plant–atmosphere continuum. Notwithstanding its clear relevance for many ecosystem processes, soil water potential is rarely measured in situ, and plant water potential observations are generally discrete, sparse, and not yet aggregated into accessible databases. These gaps limit our conceptual understanding of biophysical responses to moisture stress and inject large uncertainty into hydrologic and land-surface models. Here, we outline the conceptual and predictive gains that could be made with more continuous and discoverable observations of water potential in soils and plants. We discuss improvements to sensor technologies that facilitate in situ characterization of water potential, as well as strategies for building new networks that aggregate water potential data across sites. Here, we end by highlighting novel opportunities for linking more representative site-level observations of water potential to remotely sensed proxies. Together, these considerations offer a road map for clearer links between ecohydrological processes and the water potential gradients that have the ‘potential’ to substantially reduce conceptual and modelling uncertainties.

58 GEOSCIENCES↗
DOE OSTI2023

Requirements Description of GAMSOR and GAMSRC

This report presents the modeling and simulation capabilities of Argonne National Laboratory’s GAMSOR and GAMSRC code that is used in present reactor analysis activities. These capabilities will then be used to establish the set of verification tasks necessary to verify GAMSOR for use on commercial projects. A similar approach was taken for the PERSENT, REBUS and DIF3D software packages. The GAMSOR program is a modified version of DIF3D used to obtain the coupled neutron gamma flux distributions for a given reactor system. GAMSOR was first developed in the 1980s and its work has progressed in parallel with DIF3D throughout its various development phases. While GAMSOR is compatible with DIF3D-FD and DIF3D-Nodal, DIF3D-VARIANT is most commonly used today and will be the focus of the present verification effort. As covered in [1], GAMSOR was built to provide more accurate heating distributions by explicitly solving for both the gamma and neutron heating distributions. Without this consideration, gamma heat is normally assumed to be deposited locally at the site of gamma production. This is acceptable for modeling some phenomena because the total energy production is preserved, but it can lead to inaccurate approximations of fluence-dependent behaviors such as fuel performance, swelling, cladding embrittlement, radiation induced creep, and power peaking. The outputs from GAMSOR are contained in multiple intermediate and final output files: FIXSRC, VARSRC, GTFLUX, GHFLUX, PWDINT, NPDINT, and GPDINT. DIF3D normally produces a PWDINT file containing power density results, with the assumption that gamma rays are absorbed where they are emitted (i.e., energy deposition is local with no modeled transport). With GAMSOR, neutron power density (NPDINT) and gamma power density (GPDINT) are both produced, with their summed power densities replacing the results in PWDINT for total heating (i.e., recoverable) power density.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1985

LANDSAT TM image data quality analysis for energy-related applications

This project represents a no-cost agreement between National Aeronautic Space Administration Goddard Space Flight Center (NASA GSFC) and the Pacific Northwest Laboratory (PNL). PNL is a Department of Energy (DOE) national laboratory operted by Battelle Memorial Institute at its Pacific Northwest Laboratories in Richland, Washington. The objective of this investigation is to evaluate LANDSAT's thematic mapper (TM) data quality and utility characteristics from an energy research and technological perspective. Of main interest is the extent to which repetitive TM data might support DOE efforts relating to siting, developing, and monitoring energy-related facilities, and to basic geoscientific research. The investigation utilizes existing staff and facility capabilities, and ongoing programmatic activities at PNL and other DOE national laboratories to cooperatively assess the potential usefulness of the improved experimental TM data. The investigation involves: (1) both LANDSAT 4 and 5 TM data, (2) qualitative and quantitative use consideration, and 3) NASA P (corrected) and A (uncorrected) CCT analysis for a variety of sites of DOE interest. Initial results were presented at the LANDSAT Investigator's Workshops and at specialized LANDSAT TM sessions at various conferences.

Wukelic, G. E.↗