Search NASA⌕ Search

SEARCH · Search NASA

Results for “stress plot”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Characterization of laboratory-scale hydraulic fracturing for EGS

To investigate the impact of reservoir stimulation by hydraulic fracturing, a series of advanced lab-scale block tests were conducted with multiple measurement methods to characterize the fracture and to assess the operation and the performance of an enhanced or engineered geothermal system (EGS). The stimulation test samples were 330-mm cubic blocks of Sierra White granite with one injection well and four producers drilled into it. Acoustic emissions generated during the fracture initiation and propagation were monitored with twenty AE sensors mounted on all sides of the block to help characterize the fracture initiation and propagation process. The recorded AE signals were analyzed to obtain the event location and the failure mechanism. The localized AE events shows that due to the low viscosity of the fracturing fluid (water), the fracture propagated rapidly and took only about 1.4 s to reach near the block surface. During the fracturing phase, about 47 percent of the events were determined to be shear/mixed mode failure events, 28 percent tensile failure events, and 25 percent compressional failure events. Just after the simulation, a step-rate (constant flowrate) injection test was carried out to investigate the reservoir injectivity enhancement. During this phase additional compressional failure events were observed and the percentages of tensile failure and shear/mixed mode failure decreased. The dramatic increase of the injection rate with small increments of the injection pressure demonstrates the nonlinear response of the fracture to effective normal stress variation with much higher fracture opening increase during the low effective normal stress interval. Hydraulic fracturing tests under different stress levels show that more AE hits/events are recorded when the rock block is under higher applied stress. The reconstructed 3D fracture geometry shows good agreement with the AE monitoring results. After fracturing, a tracer test was carried out and the fracture aperture was estimated to be around 139 μm. The tracer recovery curve shows two linear portions of the tracer tail on a semi-log plot similar to that observed in some field data and predicted by numerical modeling. Laser scanning of the fracture surfaces indicates that the induced fracture has a rough surface with a joint roughness coefficient (JRC) of 12.98 and tortuosity of 1.10, both of which are slightly larger than that from the Brazilian test fracture on the same rock. The thin section and SEM observations show that the fracture follows the weak boundaries between the Quartz and Albite grains or the weak beddings in the grains.

58 GEOSCIENCES↗
DOE OSTI2021

Whole-soil warming decreases abundance and modifies the community structure of microorganisms in the subsoil but not in surface soil

Abstract. The microbial community composition in subsoils remains understudied, and it is largely unknown whether subsoil microorganisms show a similar response to global warming as microorganisms at the soil surface do. Since microorganisms are the key drivers of soil organic carbon decomposition, this knowledge gap causes uncertainty in the predictions of future carbon cycling in the subsoil carbon pool (> 50 % of the soil organic carbon stocks are below 30 cm soil depth). In the Blodgett Forest field warming experiment (California, USA) we investigated how +4 ∘C warming in the whole-soil profile to 100 cm soil depth for 4.5 years has affected the abundance and community structure of microorganisms. We used proxies for bulk microbial biomass carbon (MBC) and functional microbial groups based on lipid biomarkers, such as phospholipid fatty acids (PLFAs) and branched glycerol dialkyl glycerol tetraethers (brGDGTs). With depth, the microbial biomass decreased and the community composition changed. Our results show that the concentration of PLFAs decreased with warming in the subsoil (below 30 cm) by 28 % but was not affected in the topsoil. Phospholipid fatty acid concentrations changed in concert with soil organic carbon. The microbial community response to warming was depth dependent. The relative abundance of Actinobacteria increased in warmed subsoil, and Gram+ bacteria in subsoils adapted their cell membrane structure to warming-induced stress, as indicated by the ratio of anteiso to iso branched PLFAs. Our results show for the first time that subsoil microorganisms can be more affected by warming compared to topsoil microorganisms. These microbial responses could be explained by the observed decrease in subsoil organic carbon concentrations in the warmed plots. A decrease in microbial abundance in warmed subsoils might reduce the magnitude of the respiration response over time. The shift in the subsoil microbial community towards more Actinobacteria might disproportionately enhance the degradation of previously stable subsoil carbon, as this group is able to metabolize complex carbon sources.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2002

Remote Sensing and Information Technology for Large Farms

A method of applying of remote sensing (RS) and information management technology to help large farms produce at maximum efficiency is undergoing development. The novelty of the method does not lie in the concept of "precision agriculture," which involves variation of seeding, of application of chemicals, and of irrigation according to the spatially and temporally local variations in the growth stages and health of crops and in the chemical and physical conditions of soils. The novelty also does not lie in the use of RS data registered with other data in a geographic information system (GIS) to guide the use of precise agricultural techniques. Instead, the novelty lies in a systematic approach to overcoming obstacles that, heretofore, have impeded the timely distribution of reliable, relevant, and sufficient GIS data to support day-to-day, acre-to-acre decisions concerning the application of precise agricultural techniques to increase production and decrease cost. The development and promotion of the method are inspired in part by a vision of equipping farm machinery to accept GIS (including RS) data and using the data for automated or semiautomated implementation of precise agricultural techniques. Primary examples of relevant GIS data include information on plant stress, soil moisture, and effects of applied chemicals, all derived by automated computational analysis of measurements taken by one or more airborne spectroradiometers. Proper management and timeliness of the large amount of GIS information are of paramount concern in agriculture. Information on stresses and changes in crops is especially perishable and important to farmers. The need for timeliness and management of information is satisfied by use of computing hardware and software capable of (1) rapid georectification and other processing of RS data, (2) packaging the output data in the form of GIS plots, and (3) making the data available to farmers and other subscribers by Internet password access. It is a goal of this development program to make RS data available no later than the data after an aerial survey. In addition, data from prior surveys are kept in the data base. Farmers can, for example, use current and prior data to analyze changes.

Williams, John E.↗
DOE OSTI2023

Deformation Behavior of β Phase in a WE54 Magnesium Alloy

Second phases play a significant role in the development of high-performance magnesium alloys with rare earth elements. Here, in situ tensile tests combined with synchrotron radiation were carried out to investigate the deformation behavior of β phases in a WE (Mg–Y–Gd–Nd) alloy. By lattice strain analysis, it was found that micro load continuously transferred from the soft α-Mg matrix to the hard β phases during the whole plastic deformation, while this behavior was much more obvious at the beginning of deformation. Based on diffraction peak broadening, Williamson–Hall (W–H) plotting was used to study the microstrain of β phases. The results showed that the microstrain of β phases increased rapidly within 4% plastic strain and reached the maximum at plastic strain of ~6.5%. Since the β phases acted as hard phases, the microstrain was considered as a sign of the stress concentration near phase interfaces. It was also suggested that the effective release of local stress concentration at the β/α-Mg interface benefited the ductility of the WE alloy by the plastic deformation of β phases and phase interface sliding.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Evidence of a velocity gradient in the solar wind

Sector-boundary velocity data obtained by Mariner 5 near Venus and by Explorers 33, 34, and 35 near earth are analyzed to determine why higher velocities were measured at earth. Differences in the corresponding velocities are plotted as a function of the heliocentric latitude separation of Mariner and earth, and evidence of a significant latitude gradient in the solar wind is found. Several indirect arguments in support of a latitude gradient are presented, and it is concluded that if the solar wind velocity varies with latitude, latitudinal stresses may have a significant effect on the properties of the solar wind, such as the existence and character of the north-south component of the interplanetary magnetic field.

Smith, E. J.↗
NASA NTRS1999

Electric Field Induced Interfacial Instabilities

The study of the interface in a charge-free, critical and near-critical binary fluid in the presence of an externally applied electric field is presented. At sufficiently large fields, the interface between the two phases of the binary fluid should become unstable and exhibit an undulation with a predefined wavelength on the order of the capillary length. As the critical point is approached, this wavelength is reduced, potentially approaching length-scales such as the correlation length or critical nucleation radius. At this point the critical properties of the system may be affected. In this paper, the flat interface of a marginally polar binary fluid mixture is stressed by a perpendicular alternating electric field and the resulting instability is characterized by the critical electric field E(sub c) and the pattern observed. The character of the surface dynamics at the onset of instability is found to be strongly dependent on the frequency f of the field applied. The plot of E(sub c) vs. f for a fixed temperature shows a sigmoidal shape, whose low and high frequency limits are well described by a power-law relationship, E(sub c) = epsilon(exp zeta) with zeta = 0.35 and zeta = 0.08, respectively. The low-limit exponent compares well with the value zeta = 4 for a system of conducting and non-conducting fluids. On the other hand, the high-limit exponent coincides with what was first predicted by Onuki. The instability manifests itself as the conducting phase penetrates the non-conducting phase. As the frequency increases, the shape of the pattern changes from an array of bifurcating strings to an array of column-like (or rod-like) protrusions, each of which spans the space between the plane interface and one of the electrodes. For an extremely high frequency, the disturbance quickly grows into a parabolic cone pointing toward the upper plate. As a result, the interface itself changes its shape from that of a plane to that of a high sloping pyramid.

Kusner, Robert E.↗
NASA NTRS2003

Remote Sensing and Information Technology for Large Farms

A method of applying remote sensing (RS) and information-management technology to help large farms produce at maximum efficiency is undergoing development. The novelty of the method does not lie in the concept of precision agriculture, which involves variation of seeding, of application of chemicals, and of irrigation according to the spatially and temporally local variations in the growth stages and health of crops and in the chemical and physical conditions of soils. The novelty also does not lie in the use of RS data registered with other data in a geographic information system (GIS) to guide the use of precise agricultural techniques. Instead, the novelty lies in a systematic approach to overcoming obstacles that, heretofore, have impeded the timely distribution of reliable, relevant, and sufficient GIS data to support day-to-day, acre-to-acre decisions concerning the application of precise agricultural techniques to increase production and decrease cost. The development and promotion of the method are inspired in part by a vision of equipping farm machinery to accept GIS (including RS) data and using the data for automated or semi-automated implementation of precise agricultural techniques. Primary examples of relevant GIS data include information on plant stress, soil moisture, and effects of applied chemicals, all derived by automated computational analysis of measurements taken by one or more airborne spectroradiometers. Proper management and timeliness of the large amount of GIS information are of paramount concern in agriculture. Information on stresses and changes in crops is especially perishable and important to farmers. The need for timeliness and management of information is satisfied by use of computing hardware and software capable of (1) rapid geo-rectification and other processing of RS data, (2) packaging the output data in the form of GIS plots, and (3) making the data available to farmers and other subscribers by Internet password access. It is a goal of this development program to make RS data available no later than the data after an aerial survey. In addition, data from prior surveys are kept in the data base. Farmers can, for example, use current and prior data to analyze changes.

Williams, John E.↗
NASA NTRS2012

Some Aspects of the Failure Mechanisms in BaTiO3-Based Multilayer Ceramic Capacitors

The objective of this presentation is to gain insight into possible failure mechanisms in BaTiO3-based ceramic capacitors that may be associated with the reliability degradation that accompanies a reduction in dielectric thickness, as reported by Intel Corporation in 2010. The volumetric efficiency (microF/cm3) of a multilayer ceramic capacitor (MLCC) has been shown to not increase limitlessly due to the grain size effect on the dielectric constant of ferroelectric ceramic BaTiO3 material. The reliability of an MLCC has been discussed with respect to its structure. The MLCCs with higher numbers of dielectric layers will pose more challenges for the reliability of dielectric material, which is the case for most base-metal-electrode (BME) capacitors. A number of MLCCs manufactured using both precious-metal-electrode (PME) and BME technology, with 25 V rating and various chip sizes and capacitances, were tested at accelerated stress levels. Most of these MLCCs had a failure behavior with two mixed failure modes: the well-known rapid dielectric wearout, and so-called 'early failures." The two failure modes can be distinguished when the testing data were presented and normalized at use-level using a 2-parameter Weibull plot. The early failures had a slope parameter of Beta >1, indicating that the early failures are not infant mortalities. Early failures are triggered due to external electrical overstress and become dominant as dielectric layer thickness decreases, accompanied by a dramatic reduction in reliability. This indicates that early failures are the main cause of the reliability degradation in MLCCs as dielectric layer thickness decreases. All of the early failures are characterized by an avalanche-like breakdown leakage current. The failures have been attributed to the extrinsic minor construction defects introduced during fabrication of the capacitors. A reliability model including dielectric thickness and extrinsic defect feature size is proposed in this presentation. The model can be used to explain the Intel-reported reliability degradation in MLCCs with respect to the reduction of dielectric thickness. It can also be used to estimate the reliability of a MLCC based on its construction and microstructure parameters such as dielectric thickness, average grain size, and number of dielectric layers. Measures for preventing early failures are also discussed in this document.

Liu, David Donhang↗
NASA NTRS1978

Computer Programs (Turbomachinery)

NASA computer programs are extensively used in design of industrial equipment. Available from the Computer Software Management and Information Center (COSMIC) at the University of Georgia, these programs are employed as analysis tools in design, test and development processes, providing savings in time and money. For example, two NASA computer programs are used daily in the design of turbomachinery by Delaval Turbine Division, Trenton, New Jersey. The company uses the NASA splint interpolation routine for analysis of turbine blade vibration and the performance of compressors and condensers. A second program, the NASA print plot routine, analyzes turbine rotor response and produces graphs for project reports. The photos show examples of Delaval test operations in which the computer programs play a part. In the large photo below, a 24-inch turbine blade is undergoing test; in the smaller photo, a steam turbine rotor is being prepared for stress measurements under actual operating conditions; the "spaghetti" is wiring for test instrumentation

Source record↗
NASA NTRS1936

Turbulent Jet Expansion

This report was made to study the velocity distribution in an open, in a partially open, and in a partially expanding jet. The open-jet observations reveal minor systematic discrepancies from Tollmien's theoretical velocity distribution. The shearing-stress distribution for the partially open jet was determined. The value derived for the ratio of mixing distance to jet width was found to be in close agreement with the corresponding value for the open-jet boundary. The streamline pattern in a partially expanding channel was obtained from the observed velocity distribution and plotted, after which the distribution of the mixing distance for this case was also ascertained.

FORTHMANN E↗
DOE OSTI2019

Influence of Ce{sup 3+} Ion Doping on Structural and Magnetic Properties of Magnesium Nanoferrite

Pure and rare earth ion Ce{sup 3+}-doped magnesium nanoferrite magnetic particles, i.e., MgFe{sub 2}O{sub 4} and MgCe{sub x}Fe{sub 2−x}O{sub 4} (x = 0.0, 0.025, 0.05, 0.075, and 0.1) were successfully fabricated using sol-gel technique, and qualitative studies were carried out using X-ray diffractometer (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), high-resolution field-emission scanning electron microscopy (HRFESEM) equipped with energy-dispersive spectroscopy (EDS), vibrating sample magnetometer (VSM), and electron paramagnetic resonance (EPR) techniques. X-ray diffraction analysis confirmed the crystalline phase of the synthesized samples with no extra phase. The crystallite size obtained from W-H plots follow the same trend as calculated using Scherrer method, and the strain decreases with increasing Ce{sup 3+} ion concentration indicating a lesser number of deformities. FTIR spectra revealed the shifting of lower-frequency band to the higher side with the larger radii Ce{sup 3+} ions. HRFESEM images reveal the reduction in stress on doping. No additional impurities are observed in synthesized samples as is confirmed by EDS analysis. The average particle size obtained by TEM are in agreement with XRD analysis. EPR studies showed an increase in g value and line width with doping. Magnetic measurements carried out at room temperature reveals the value of magnetization initially decreases up to x = 0.05 and afterwards increases with the addition of Ce{sup 3+} ions. These properties reveal superparamagnetic nature of cerium-doped magnesium nanoparticles and can be suitable for catalyst and humidity sensors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Impacts of Degradation on Water, Energy, and Carbon Cycling of the Amazon Tropical Forests

Selective logging, fragmentation, and understory fires directly degrade forest structure and composition. However, studies addressing the effects of forest degradation on carbon, water, and energy cycles are scarce. Here, we integrate field observations and high-resolution remote sensing from airborne lidar to provide realistic initial conditions to the Ecosystem Demography Model (ED-2.2) and investigate how disturbances from forest degradation affect gross primary production (GPP), evapotranspiration (ET), and sensible heat flux (H). We used forest structural information retrieved from airborne lidar samples (13,500 ha) and calibrated with 817 inventory plots (0.25 ha) across precipitation and degradation gradients in the eastern Amazon as initial conditions to ED-2.2 model. Our results show that the magnitude and seasonality of fluxes were modulated by changes in forest structure caused by degradation. During the dry season and under typical conditions, severely degraded forests (biomass loss ≥66%) experienced water stress with declines in ET (up to 34%) and GPP (up to 35%) and increases of H (up to 43%) and daily mean ground temperatures (up to 6.5°C) relative to intact forests. In contrast, the relative impact of forest degradation on energy, water, and carbon cycles markedly diminishes under extreme, multiyear droughts, as a consequence of severe stress experienced by intact forests. Our results highlight that the water and energy cycles in the Amazon are driven by not only climate and deforestation but also the past disturbance and changes of forest structure from degradation, suggesting a much broader influence of human land use activities on the tropical ecosystems.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

Impacts of Degradation on Water, Energy, and Carbon Cycling of the Amazon Tropical Forests

Selective logging, fragmentation, and understory fires directly degrade forest structure and composition. However, studies addressing the effects of forest degradation on carbon, water, and energy cycles are scarce. Here, we integrate field observations and high‐resolution remote sensing from airborne lidar to provide realistic initial conditions to the Ecosystem Demography Model (ED‐2.2) and investigate how disturbances from forest degradation affect gross primary production (GPP), evapotranspiration (ET), and sensible heat flux (H). We used forest structural information retrieved from airborne lidar samples (13,500 ha) and calibrated with 817 inventory plots (0.25 ha) across precipitation and degradation gradients in the eastern Amazon as initial conditions to ED‐2.2 model. Our results show that the magnitude and seasonality of fluxes were modulated by changes in forest structure caused by degradation. During the dry season and under typical conditions, severely degraded forests (biomass loss ≥66%) experienced water stress with declines in ET (up to 34%) and GPP (up to 35%) and increases of H (up to 43%) and daily mean ground temperatures (up to 6.5°C) relative to intact forests. In contrast, the relative impact of forest degradation on energy, water, and carbon cycles markedly diminishes under extreme, multiyear droughts, as a consequence of severe stress experienced by intact forests. Our results highlight that the water and energy cycles in the Amazon are driven by not only climate and deforestation but also the past disturbance and changes of forest structure from degradation, suggesting a much broader influence of human land use activities on the tropical ecosystems.

Marcos Longo↗
NASA NTRS2015

Forest Disturbance Across the Conterminous United States from 1985-2012: The Emerging Dominance of Forest Decline

Evidence of shifting dominance among major forest disturbance agent classes regionally to globally has been emerging in the literature. For example, climate-related stress and secondary stressors on forests (e.g., insect and disease, fire) have dramatically increased since the turn of the century globally, while harvest rates in the western US and elsewhere have declined. For shifts to be quantified, accurate historical forest disturbance estimates are required as a baseline for examining current trends. We report annual disturbance rates (with uncertainties) in the aggregate and by major change causal agent class for the conterminous US and five geographic subregions between 1985 and 2012. Results are based on human interpretations of Landsat time series from a probability sample of 7200 plots (30 m) distributed throughout the study area. Forest disturbance information was recorded with a Landsat time series visualization and data collection tool that incorporates ancillary high-resolution data. National rates of disturbance varied between 1.5% and 4.5% of forest area per year, with trends being strongly affected by shifting dominance among specific disturbance agent influences at the regional scale. Throughout the time series, national harvest disturbance rates varied between one and two percent, and were largely a function of harvest in the more heavily forested regions of the US (Mountain West, Northeast, and Southeast). During the first part of the time series, national disturbance rates largely reflected trends in harvest disturbance. Beginning in the mid-90s, forest decline-related disturbances associated with diminishing forest health (e.g., physiological stress leading to tree canopy cover loss, increases in tree mortality above background levels), especially in the Mountain West and Lowland West regions of the US, increased dramatically. Consequently, national disturbance rates greatly increased by 2000, and remained high for much of the decade. Decline-related disturbance rates reached as high as 8% per year in the western regions during the early-2000s. Although low compared to harvest and decline, fire disturbance rates also increased in the early- to mid-2000s. We segmented annual decline-related disturbance rates to distinguish between newly impacted areas and areas undergoing gradual but consistent decline over multiple years. We also translated Landsat reflectance change into tree canopy cover change information for greater relevance to ecosystem modelers and forest managers, who can derive better understanding of forest-climate interactions and better adapt management strategies to changing climate regimes. Similar studies could be carried out for other countries where there are sufficient Landsat data and historic temporal snapshots of high-resolution imagery.

Cohen, Warren B.↗
DOE OSTI2022

High-temperature compressive creep tests of U 3 Si 2 with spark plasma sintering: Experiments and finite element modeling

This paper reports a systematic high-temperature creep behavior of dense U 3 Si 2 pellets using a spark plasma sintering (SPS) apparatus at elevated temperatures and pressures under vacuum conditions. The stress exponent was subsequently derived to be 3.21 at 1173 K and 2.17 at 1223 K, respectively, indicating a grain boundary sliding creep mechanism. The creep activation energy was determined to be 203.6 ± 19.0 kJ/mol, which agrees well with the literature. Finite element modeling was performed using the creep parameters fitted from the strain-time plot. Additionally, the results suggest an excellent match with the experimental data, confirming the validity of the experiments. Microstructure characterizations indicate that the main phase of the specimens after creep tests remains to be U 3 Si 2 , with a 4 μm thick layer of nano-sized particles induced from the diffusion between U 3 Si 2 and alumina disc used to avoid electric current passing through the sample. The successful conduct of creep experiments demonstrates the great potential of SPS to perform high-temperature mechanical testing of nuclear fuels under vacuum conditions. The subsequent finite element modeling exhibits excellent capabilities for accurately predicting material performance in the creep tests and provides a practical tool in evaluating nuclear fuels’ performance for a much-extended time scale.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A Computer Model to Study the Response of Energetic Materials to a Range of Dynamic Loads

Over the past decade we developed a model to enable computer simulation of the mechanical and subsequent energetic response of explosives and propellants to mechanical insults such as impacts, perforations, drops, and falls. The model is embedded in computer simulation programs that solve the non-linear, large deformation equations of compressible solid and fluid flow in space and time. It is implemented as a user-defined model, which returns the updated stress tensor and composition that result from the simulation supplied strain tensor change. Although it is multi-phase, in that gas and solid species are present, it is single-velocity, in that the gas does not flow through the porous solid. More than 70 time-dependent variables are made available for additional analyses and plotting. The model encompasses a broad range of possible responses: mechanical damage with no energetic response, and a continuous spectrum of degrees of violence including delayed and prompt detonation. This work describes the basic workings of the model.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Progress in the measurement of SSME turbine heat flux with plug-type sensors

Data reduction was completed for tests of plug-type heat flux sensors (gauges) in a turbine blade thermal cycling tester (TBT) that is located at NASA/Marshall Space Flight Center, and a typical gauge is illustrated. This is the first time that heat flux has been measured in a Space Shuttle Main Engine (SSME) Turbopump Turbine environment. The development of the concept for the gauge was performed in a heat flux measurement facility at Lewis. In this facility, transient and steady state absorbed surface heat flux information was obtained from transient temperature measurements taken at points within the gauge. A schematic of the TBT is presented, and plots of the absorbed surface heat flux measured on the three blades tested in the TBT are presented. High quality heat flux values were measured on all three blades. The experiments demonstrated that reliable and durable gauges can be repeatedly fabricated into the airfoils. The experiment heat flux data are being used for verification of SSME analytical stress, boundary layer, and heat transfer design models. Other experimental results and future plans are also presented.

Liebert, Curt H.↗
DOE OSTI2020

Data from: "Growth strategies and threshold responses to water deficit modulate effects of warming on tree seedlings from forest to alpine"

This data package contains data that were used to support conclusions drawn in “Growth strategies and threshold responses to water deficit modulate effects of warming on tree seedlings from forest to alpine”, by Lazarus, Castanha et al. 2017. Data were collected at field sites within the Alpine Treeline Warming Experiment (ATWE) on Niwot Ridge, Colorado, USA, and at the U.S. Geological Survey laboratory located in Boise, Idaho. This archive contains comma-separated-values (.csv) files, as well as the same files in Microsoft Excel (.xlsx) format, which can be opened by either Microsoft Excel, R, or any simple text editor program. There are two types of geospatial data files: .kml and ESRI shapefiles (.shp). The kml files contain placemarks, which can be opened by Google Earth, or Google Maps. The ESRI shapefiles can be opened by any geographic information system application that can read shapefiles, including ESRI's entire ArcGIS suite, and QGIS. We asked whether and how tree species differences in response to water deficit relates to their establishment along the gradient from forest to alpine. To do this, we compared growth and moisture stress responses in first-year seedlings of three species planted in common gardens subject to a factorial of heating and watering treatments below, at, and above tree line. This combination of an elevation gradient alongside warming and watering treatments enabled us to observe species differences in seedling responses to a broad set of climatic conditions.Entire seedlings were harvested at c. 3- and again at 9 weeks of age following germination/emergence in the experimental plots, and we then measured dry mass (DM) of above and belowground parts, root length, root mass fraction (RMF), relative growth rates (RGRs) from seed to 3 weeks and from 3 to 9 weeks, turgor-loss point (TLP), and photosynthetic WUE (as δ13C). Also included in this dataset (but not described in the manuscript) are measures of specific leaf area (SLA) and other variables generated by pressure-volume curves (saturated water content, osmotic potential at full turgor, elastic modulus).

54 ENVIRONMENTAL SCIENCES↗