Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface charging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Electron beam injection from a hollow cathode plasma into a downstream reactive environment: Characterization of secondary plasma production and Si 3 N 4 and Si etching

A material etching system was developed by combining beam electron injection from a direct current (DC) hollow-cathode (HC) electron source with the downstream reactive environment of a remote CF 4 /O 2 low temperature plasma. The energy of the injected beam electrons is controlled using an acceleration electrode biased positively relative to the HC Argon discharge. For an acceleration voltage greater than the ionization potential of Ar, the extracted primary electrons can produce a secondary plasma in the process chamber. We characterized the properties of the secondary plasma by performing Langmuir probe measurements of the electron energy probability function (EEPF) 2.5 cm below the extraction ring. The data indicate the existence of two major groups of electrons, including electrons with a primary beam electron energy which varies as the acceleration voltage is varied, along with low energy electrons produced by ionization of the Ar gas atoms in the process chamber by the injected beam electrons. When combining the HC Ar beam electron with a remote CF 4 /O 2 electron cyclotron wave resonance (ECWR) plasma, the EEPF of both the low energy plasma electron and beam electron components decreases. Additionally, we studied surface etching of Si3N4 and poly-crystalline Si (poly-Si) thin films as a function of process parameters, including the acceleration voltage (0-70 V), discharge current of the HC discharge (1-2 A), pressure (2- 100 mTorr), source to substrate distance (2.5 to 5 cm), and feed gas composition (with or without CF 4 /O 2 ). The direction of the incident beam electrons was perpendicular to the surface. Si 3 N 4 and poly-crystalline silicon etching are seen and indicate an electronneutral synergy effect. No/little remote plasma spontaneous etching was observed for the conditions used in this study, and the etching is confined to the substrate area irradiated by the injected beam electrons. The electron etched Si 3 N 4 surface etching rate profile distribution is confined within a ~30 mm diameter circle, which is slightly broader than the area for which poly-Si etching is seen, and coincides closely with the spatial profile of beam electrons as determined by the Langmuir probe measurements. The magnitude of poly-Si etching rate is by a factor of two times smaller than the Si 3 N 4 etching rate. In this paper, we discuss possible explanations of the data and the role of surface charging.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1982

Potentials on large spacecraft in LEO

A system-oriented computer code is used to predict surface charging due to voltages generated within a satellite operating in the typical dense plasma environment of LEO. The use of this code is demonstrated by predicting the expansion of electric fields onto a kapton surface from a pinhole over a biased conductor in a LEO environment. The results are compared to a more-exact solution and experimental data.

Mandell, M. J.↗
NASA NTRS1998

Potential for Fabric Damage by Welding Electron Beam

Welding electron beam effects on Nextel AF-62 ceramic fabric enable a preliminary, tentative interpretation of electron beam fabric damage. Static surface charging does not protect fabric from beam penetration, but penetration occurs only after a delay time. The delay time is thought to be that required for the buildup of outgassing products at the fabric surface to a point where arcing occurs. Extra long delays are noted when the gun is close enough to the surface to be shut off by outgassing emissions. Penetration at long distances is limited by beam attenuation from electronic collisions with the chamber atmosphere.

Fragomeni, James M.↗
NASA NTRS2006

Electrostatic Properties of PE and PTFE Subjected to Atmospheric Pressure Plasma Treatment; Correlation of Experimental Results with Atomistic Modeling

The use of an atmospheric pressure glow discharge (APGD) plasma was used at KSC to increase the hydrophilicity of spaceport materials to enhance their surface charge dissipation and prevent possible ESD in spaceport operations. Significant decreases in charge decay times were observed after tribocharging the materials using the standard KSC tribocharging test. The polarity and amount of charge transferred was dependent upon the effective work function differences between the respective materials. In this study, polyethylene (PE) and polytetrafluoroethylene (PTFE) were exposed to a He+O2 APGD. The pre and post treatment surface chemistry was analyzed by X-ray photoelectron spectroscopy and contact angle measurements. Semi-empirical and ab initio calculations were performed to correlate the experimental results with some plausible molecular and electronic structure features of the oxidation process. For the PE, significant surface oxidation was observed, as indicated by XPS showing C-O, C=O, and O-C=O bonding, and a decrease in the surface contact angle from 98.9 deg to 61.2 deg. For the PTFE, no C-O bonding appeared and the surface contact angle increased indicating the APGD only succeeded in cleaning the PTFE surface without affecting the surface structure. The calculations using the PM3 and DFT methods were performed on single and multiple oligomers to simulate a wide variety of oxidation scenarios. Calculated work function results suggest that regardless of oxidation mechanism, e.g. -OH, =0 or a combination thereof, the experimentally observed levels of surface oxidation are unlikely to lead to a significant change in the electronic structure of PE and that its increased hydrophilic properties are the primary reason for the observed changes in its electrostatic behavior. The calculations for PTFE argue strongly against significant oxidation of that material, as confirmed by the XPS results.

Trigwell, Steve↗
DOE OSTI2024

Charge‐Programmable Photopolymers for 3D Electronics via Additive Manufacturing

Charge‐programmed 3D printing enables the fabrication of 3D electronics with lightweight and high precision via selective patterning of metals. This selective metal deposition is catalyzed by Pd nanoparticles that are specifically immobilized onto the charged surface and promises to fabricate a myriad of complex electronic devices with self‐sensing, actuation, and structural elements assembled in a designed 3D layout. However, the achievable property space and the material‐performance correlation of the charge‐programmed printing remain unexplored. Herein, a series of photo‐curable resins are designed for unveiling how the charge and crosslink densities synergistically impact the nanocatalyst‐guided selective deposition in catalytic efficiency and properties of the 3D printed charge‐programmed architectures, leading to high‐quality 3D patterning of solid and liquid metals. The findings offer a wide tunability of the structural properties of the printed electronics, ranging from stiff to extreme flexibility. Capitalizing on these results, the printing and successful application of an ultralight‐weight and deployable 3D multi‐layer antenna system operating at an ultrahigh‐frequency of 19 GHz are demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

COVID-19 global pandemic planning: Performance and electret charge of N95 respirators after recommended decontamination methods

Shortages of N95 respirators for use by medical personnel have driven consideration of novel conservation strategies, including decontamination for reuse and extended use. Decontamination methods listed as promising by the Centers for Disease Control and Prevention (CDC) (vaporous hydrogen peroxide (VHP), wet heat, ultraviolet irradiation (UVI)) and several methods considered for low resource environments (bleach, isopropyl alcohol and detergent/soap) were studied for two commonly used surgical N95 respirators (3M™ 1860 and 1870+ Aura™). Although N95 filtration performance depends on the electrostatically charged electret filtration layer, the impact of decontamination on this layer is largely unexplored. As such, respirator performance following decontamination was assessed based on the fit, filtration efficiency, and pressure drop, along with the relationship between (1) surface charge of the electret layer, and (2) elastic properties of the straps. Decontamination with VHP, wet heat, UVI, and bleach did not degrade fit and filtration performance or electret charge. Isopropyl alcohol and soap significantly degraded fit, filtration performance, and electret charge. Pressure drop across the respirators was unchanged. Modest degradation of N95 strap elasticity was observed in mechanical fatigue testing, a model for repeated donnings and doffings. CDC recommended decontamination methods including VHP, wet heat, and UV light did not degrade N95 respirator fit or filtration performance in these tests. Extended use of N95 respirators may degrade strap elasticity, but a loss of face seal integrity should be apparent during user seal checks. NIOSH recommends performing user seal checks after every donning to detect loss of appropriate fit. Decontamination methods which degrade electret charge such as alcohols or detergents should not be used on N95 respirators. The loss of N95 performance due to electret degradation would not be apparent to a respirator user or evident during a negative pressure user seal check.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Simultaneous mapping of nanoscale dielectric, electrochemical, and ferroelectric surface properties of van der Waals layered ferroelectric via advanced SPM

Ferroelectric surfaces involve a complex interplay between polarization and dielectric properties, internal and external surface charge screening, and ionic and electrochemical effects. There is currently no good way to simultaneously capture all the required information at appropriate length scales. To this end, we present an advanced scanning probe microscopy approach for simultaneously mapping surface potential, dielectric, and piezoelectric properties on the nanoscale. For quantitatively mapping electromechancial properties, we utilize interferometric displacement sensing piezoresponse force microscopy, which measures the effective piezoelectric coefficient free of background artifacts such as the cantilever body electrostatics. The dielectric and surface electrochemical properties are captured during G-mode electrostatic force microscopy/Kelvin probe force microscopy operated in the lift mode. We show the capabilities of this approach on the chemically phase separated composite sample consisting of a van der Waals layered ferroelectric CuInP 2 S 6 phase and a non-polar In 4/3 P 2 S 6 phase. Finally, we demonstrate domain structure evolution during thermally stimulated phase transition.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Direct Experimental Observations of Ion Distributions during Overcharging at the Muscovite–Water Interface by Adsorption of Rb + and Halides (Cl – , Br – , I – ) at High Salinity

Classical electric double layer (EDL) models have been widely used to describe ion distributions at charged solid-water interfaces in dilute electrolytes. However, the chemistry of EDLs remains poorly constrained at high ionic strength where ion-ion correlations control non-classical behavior such as overcharging, i. e., the accumulation of counter-ions in amounts exceeding the substrate's surface charge. Here, we provide direct experimental observations of correlated cation and anion distributions adsorbed at the muscovite (001)-aqueous electrolyte interface as a function of dissolved RbBr concentration ([RbBr]=0.01–5.8 M) using resonant anomalous X-ray reflectivity. Our results show alternating cation-anion layers in the EDL when [RbBr]≳100 mM, whose spatial extension (i. e., ~20 Å from the surface) far exceeds the dimension of the classical Stern layer. Comparison to RbCl and RbI electrolytes indicates that these behaviors are sensitive to the choice of co-ion. This new in-depth molecular-scale understanding of the EDL structure during transition from classical to non-classical regimes supports the development of realistic EDL models for technologies operating at high salinity such as water purification applications or modern electrochemical storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2009

Charged Particle Environments in Earth's Magnetosphere and their Effects on Space System

This slide presentation reviews information on space radiation environments important to magnetospheric missions including trapped radiation, solar particle events, cosmic rays, and solar winds. It also includes information about ion penetration of the magnetosphere, galactic cosmic rays, solar particle environments, CRRES internal discharge monitor, surface charging and radiation effects.

Minow, Joseph I.↗
DOE OSTI2021

Sorption and electrokinetic properties of ASR product and C-S-H: A comparative modelling study

Alkali-silica reaction (ASR) is one of the most important concrete durability issues worldwide. ASR products formed at high temperature have a structure similar to the natural mineral shlykovite. Reactive Grand Canonical Simulations were used to investigate sorption of K{sup +}, Cl{sup −} and Ca{sup 2+} on C-S-H and ASR products at different pH (10.0 to 13.0) and pore water chemistry. Divalent ions can overcompensate for the negative surface charge, in particular for C-S-H, which leads to a co-adsorption of negative species such as Cl{sup −}. At high K/Ca in solution, monovalent K{sup +} can desorb calcium from C-S-H and shlykovite surface. The calculated Ca/K partition coefficient shows a higher affinity of ASR product for K{sup +}, while C-S-H favours Ca{sup 2+}. The uptake of K{sup +} by ASR products lowers the alkali concentration in the solution and could thus slow down the rate of ASR.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Relaxation behavior in low-frequency complex conductivity of sands caused by bacterial growth and biofilm formation by Shewanella oneidensis under a high-salinity condition

Complex electrical conductivity is increasingly used to monitor subsurface processes associated with microbial activities because microbial cells mostly have surface charges and thus electrical double layers. Although highly saline environments are frequently encountered in coastal and marine sediments, there are limited data available on the complex conductivity associated with microbial activities under a high-salinity condition. Therefore, we have developed the spectral responses of complex conductivity of sand associated with bacterial growth and biofilm formation under a highly saline condition of approximately 1% salinity and approximately 2 S/m pore water conductivity with an emphasis on relaxation behavior. A column test is performed, in which the model bacteria Shewanella oneidensis MR-1 are stimulated for cell growth and biofilm formation in a sand pack, whereas the complex conductivity is monitored from 0.01 Hz to 10 kHz. The test results indicate that the real conductivity increases in the early stage due to the microbial metabolites and the increased surface conduction with cell growth but soon begin to decrease because of the reduction of charge passages due to bioclogging. However, the imaginary conductivity significantly increases with time, and clear bell-shaped relaxation behaviors are observed with the peak frequency of 0.1–1 Hz, associated with the double-layer polarization of cells and electrically conductive pili and biofilms. The Cole-Cole relaxation model appears to capture such relaxation behaviors well, and the modeling results indicate gradual increases in normalized chargeability and decreases in relaxation time during bacterial growth and biofilm formation in the highly saline condition. Comparison with previous literature confirms that the high-salinity condition further increases the normalized chargeability, whereas it suppresses the phase shift and thus the imaginary conductivity. Our results suggest that the complex conductivity can effectively capture microbial biomass formation in sands under a highly saline condition.

58 GEOSCIENCES↗
DOE OSTI2023

Heavy Versus Light Lanthanide Selectivity for Graphene Oxide Films is Concentration Dependent

Rare earths are important materials in various technologies such as catalysis and optoelectronics. Graphene oxide (GO) is a promising material for separation applications, including the isolation of lanthanides from complex mixtures. Previous works using fatty acid monolayers have demonstrated preferential heavy versus light lanthanide adsorption, which has been attributed to differences in lanthanide ion size. In this work, we used interfacial X-ray fluorescence measurements to reveal that GO thin films at the air/water interface have no lanthanide selectivity for dilute subphases. However, at high subphase concentrations, ~8 times more Lu is adsorbed than La. By comparing the GO results with an ideal monolayer with a carboxylic acid headgroup, arachidic acid (AA), we demonstrate that the number of Lu ions adsorbed to GO is significantly higher than the number expected to compensate for the surface charge. Vibrational sum frequency generation (SFG) spectroscopy results on both GO thin films and AA monolayers reveal a red-shifted SFG signal in the OH region, which we attribute to partial dehydration of the adsorbed ions and carboxylic acid headgroups. Liquid surface X-ray reflectivity data show that the GO thin film structure does not significantly change between the very dilute and concentrated subphases. We speculate that the functional groups of both GO and AA facilitate cation dehydration, which is essential for ion adsorption. Heavy lanthanide Lu has stronger ion–ion correlations that can overcome the electrostatic repulsion between cations at higher concentrations compared to light lanthanide La, meaning GO and AA can exhibit apparent overcharge with Lu. Lastly, the layered structure of the GO films and reactive chemical nature of GO itself can accommodate ion adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2011

DMSP Spacecraft Charging in Auroral Environments

The Defense Meteorological Satellite Program (DMSP) spacecraft are a series of low-earth orbit (LEO) satellites whose mission is to observe the space environment using the precipitating energetic particle spectrometer (SSJ/4-5). DMSP satellites fly in a geosynchronous orbit at approx.840 km altitude which passes through Earth s ionosphere. The ionosphere is a region of partially ionized gas (plasma) formed by the photoionization of neutral atoms and molecules in the upper atmosphere of Earth. For satellites in LEO, such as DMSP, the plasma density is usually high and the main contributors to the currents to the spacecraft are the precipitating auroral electrons and ions from the magnetosphere as well as the cold plasma that constitutes the ionosphere. It is important to understand how the ionosphere and auroral electrons can accumulate surface charges on satellites because spacecraft charging has been the cause of a number of significant anomalies for on-board instrumentation on high altitude spacecraft. These range from limiting the sensitivity of measurements to instrument malfunction depending on the magnitude of the potential difference over the spacecraft surface. Interactive Data Language (IDL) software was developed to process SSJ/4-5 electron and ion data and to create a spectrogram of the particles number and energy fluxes. The purpose of this study is to identify DMSP spacecraft charging events and to present a preliminary statistical analysis. Nomenclature

Colson, Andrew↗
NASA NTRS1994

Permeability of membranes to amino acids and modified amino acids: mechanisms involved in translocation

The amino acid permeability of membranes is of interest because they are one of the key solutes involved in cell function. Membrane permeability coefficients (P) for amino acid classes, including neutral, polar, hydrophobic, and charged species, have been measured and compared using a variety of techniques. Decreasing lipid chain length increased permeability slightly (5-fold), while variations in pH had only minor effects on the permeability coefficients of the amino acids tested in liposomes. Increasing the membrane surface charge increased the permeability of amino acids of the opposite charge, while increasing the cholesterol content decreased membrane permeability. The permeability coefficients for most amino acids tested were surprisingly similar to those previously measured for monovalent cations such as sodium and potassium (approximately 10(-12)-10(-13) cm s-1). This observation suggests that the permeation rates for the neutral, polar and charged amino acids are controlled by bilayer fluctuations and transient defects, rather than partition coefficients and Born energy barriers. Hydrophobic amino acids were 10(2) more permeable than the hydrophilic forms, reflecting their increased partition coefficient values. External pH had dramatic effects on the permeation rates for the modified amino acid lysine methyl ester in response to transmembrane pH gradients. It was established that lysine methyl ester and other modified short peptides permeate rapidly (P = 10(-2) cm s-1) as neutral (deprotonated) molecules. It was also shown that charge distributions dramatically alter permeation rates for modified di-peptides. These results may relate to the movement of peptides through membranes during protein translocation and to the origin of cellular membrane transport on the early Earth.

Review↗
DOE OSTI2022

Nanoscale Measurements of Charge Transfer at Cocatalyst/Semiconductor Interfaces in BiVO 4 Particle Photocatalysts

Semiconductor photocatalyst particles convert solar energy to fuels like H 2 . The particles are often assumed to provide crystalline-facet-dependent electron-hole separation. A common strategy is to deposit HER electrocatalyst on electron-selective facets and OER electrocatalyst on hole-selective facets. A precise understanding of how charge-carrier-selective contacts emerges and how they rationally designed, however, is missing. Using a combination of ex-situ and in-situ conducting-AFM experiments and new ionomer/catalyst-semiconductor test structures, we show how heterogeneity in charge-carrier selectivity can be measured at the nanoscale. We discover that the presence of interface water/electrolyte is critical to induce hole selectivity between the CoO x water-oxidation catalyst and the BiVO 4 light absorber. pH-dependent measurements suggest that negative surface charge on the semiconductor is central to inducing hole selectivity. Furthermore, the work also demonstrates a new approach to control local pH and introduce water using thin-film ionomers compatible with conductive-AFM measurements.

14 SOLAR ENERGY↗
DOE OSTI2023

Large-volume CdZnTe bar detectors characterized by laser-induced transient currents

In this work, we studied the free-carrier transport properties and space-charge formation/polarization in a CdZnTe bar-shaped radiation detector using the Laser-Induced Transient Current technique. We found out that a steady-state space charge ranging from 8 x 10 8 to 2.1 x 10 9 cm -3 is formed throughout the detector at about 0.5 s following biasing. The measured current waveforms were modeled by Monte Carlo simulations after taking into account the electric and weighting fields inside the detector and shielding box. Modeling of the unpolarized waveforms revealed an exceptionally high electron mobility-lifetime product μ e τ e ≥0.095cm 2 V -1 . The observed formation of positive space charge in the biased detector and linear scaling of the current waveform shapes on applied bias revealed that the detector polarization is attributed to carrier injection at the anode. In conclusion, measurements in pulsed and DC bias in modified electrode geometry proved the surface-charge formation.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Dispersing nano- and micro-sized portlandite particulates via electrosteric exclusion at short screening lengths

In spite of their high surface charge (zeta potential ζ = +34 mV), aqueous suspensions of portlandite (calcium hydroxide: Ca(OH) 2 ) exhibit a strong tendency to aggregate, and thereby present unstable suspensions. While a variety of commercial dispersants seek to modify the suspension stability and rheology (e.g., yield stress, viscosity), it remains unclear how the performance of electrostatically and/or electrosterically based additives is affected in aqueous environments having either a high ionic strength and/or a pH close to the particle's isoelectric point (IEP). We show that the high native ionic strength (pH ≈ 12.6, IEP: pH ≈ 13) of saturated portlandite suspensions strongly screens electrostatic forces (Debye length: κ -1 = 1.2 nm). As a result, coulombic repulsion alone is insufficient to mitigate particle aggregation and affect rheology. However, a longer-range geometrical particle–particle exclusion that arises from electrosteric hindrance caused by the introduction of comb polyelectrolyte dispersants is very effective at altering the rheological properties and fractal structuring of suspensions. As a result, comb-like dispersants that stretch into the solvent reduce the suspension's yield stress by 5× at similar levels of adsorption as compared to linear dispersants, thus enhancing the critical solid loading (i.e., at which jamming occurs) by 1.4×. Significantly, the behavior of diverse dispersants is found to be inherently related to the thickness of the adsorbed polymer layer on particle surfaces. These outcomes inform the design of dispersants for concentrated suspensions that present strong charge screening behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanistic study of pH effect on organic solvent nanofiltration using carboxylated covalent organic framework as a modeling and experimental platform

Covalent organic framework (COF) membranes for organic solvent nanofiltration (OSN) have attracted growing interest due to their high stability, well-defined pore size, and controllable pore functionality. In aqueous nanofiltration processes, solution pH has a significant effect on membrane permeability, selectivity, and fouling. However, our understanding of pH effects on OSN processes is still limited. In this work, we present experimental and reactive force field molecular dynamics (ReaxFF MD) simulation results on the effect of pH on OSN using a well-characterized carboxylated COF (C-COF) membrane. Filtration experimental and modeling results both demonstrate that pH changes can affect solvent permeance and solute rejection dramatically. Specifically, methanol permeance decreases with the increase of NaOH and HCl concentration, respectively. When Alcian Blue dye was used as the solute in methanol, the selectivity increased from 23% to 98% when changing the feed pH from 2.2 to 10.1, respectively. While ReaxFF MD results show that C-COF solvated pore size is only marginally affected by the pH of solution, methanol diffusion is affected by the size of methanol-solvated Na + and Cl - ions, which increase with increasing Na + and Cl - concentrations. Solution pH change also affected solute solvation layer thicknesses and C-COF pore charges, contributing to the significant AB dye selectivity increase with pH increase. To summarize, we have shown that dramatic changes in C-COF selectivity are not anomalous in OSN, but are instead controllable by varying feed solution pH to modify solvated solute radii and surface charge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗