Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Spectral emissivity measurements of land-surface materials and related radiative transfer simulations

Spectral radiance measurements have been made in the laboratory and in the field for deriving spectral emissivities of some land cover samples with a spectroradiometer and an auxiliary radiation source in the wavelength range 2.5-14.5 micrometers. A easy and quick four-step method (four steps to measure the sample and a diffuse reflecting plate surface under sunshine and shadowing conditions, respectively) has been used for simultaneous determination of surface temperature and emissivity. We emphasized in-situ measurements in combination with radiative transfer simulations, and an error analysis for basic assumptions in deriving spectral emissivity of land-surface samples from thermal infrared measurements.

Wan, Z.↗

On the Emitted Dust Size Distribution and Its Variability: Insights From A Field Campaign in an Ephemeral Lake of the Lower Drâa Valley, Moroccan Sahara

During the last decades the emitted particle size distribution (PSD) of dust and its variability have been actively discussed due to their effects on the Earth System. Some frameworks support a higher proportion of aggregate’s fragmentation as wind speed increases, while others suggest the PSD independence of wind speed and soil properties, at least up to ~10 µm. Constraining the size-resolved dust emission and its variability is key to reduce the uncertainty of Earth system models, but still requires further analysis. The ERC project FRAGMENT addresses these and other issues related to dust emission, dust mineralogical composition and its effects upon climate. In this context we conducted a one month field campaign in September 2019 at L’Bour, an ephemeral lake located in the Lower Drâa Valley, resulting in a detailed description of the soil, dust emission and meteorology. During the campaign saltation and dust emission were very frequent under two prevailing wind directions. Friction velocity varied around 0.15 ms⁻¹, with peaks close to 0.4 ms⁻¹, except for a peak of 0.6 ms⁻¹ coinciding with the arrival of one of the moist convective storms or haboobs that occurred during this period. We study the near-surface concentration and diffusive flux PSDs along with their variability up to ~19 µm in optical diameter (~21 µm in geometric dust diameter). As expected, we find significant differences between the concentration and diffusive flux PSDs, with the latter showing a higher proportion of coarse and super-coarse particles. Our results also highlight dependencies of the PSDs with friction velocity, wind direction, and type of event (regular events vs haboob outflow events). We first discuss the potential origin of the variations and dependencies, which include 1) differences in fetch and surface between directions, 2) dry deposition of coarse and super-coarse dust depending on friction velocity, 3) more disaggregation with increasing friction velocity, and 4) the effect of the haboob gust front. Our calculations show the influence of dry deposition upon the diffusive flux PSDs. We finally compare our PSDs with brittle fragmentation theory, both with the original 2011 formulation using optical diameters, and with the more recent 2022 formulation including the emission of super-coarse dust and using geometric diameters.

particle size distribution↗

Transmission of isotropic light across a dielectric surface in two and three dimensions.

Average transmittance of polarized diffuse light across a dielectric surface is calculated in both two and three dimensions. The incident light in both cases is confined to an angular range measured from the surface normal. Limiting values in three dimensions correspond to known results for two cases, (1) normal incidence, and (2) diffuse light incident from a 180 deg cone. The two-dimensional formulation is solvable in terms of elliptic functions and incomplete elliptic integrals of the first, second, and third kinds. Results are displayed graphically for values of transmittances in excess of 0.9 associated with relative indices of refraction in the range m = 1.0 to m = 2.6.

Allen, W. A.↗

Non-Lambertian effects on remote sensing of surface reflectance and vegetation index

This paper discusses the effects of non-Lambertian reflection from a homogeneous surface on remote sensing of the surface reflectance and vegetation index from a satellite. Remote measurement of the surface characteristics is perturbed by atmospheric scattering of sun light. This scattering tends to smooth the angular dependence of non-Lambertian surface reflectances, an effect that is not present in the case of Lambertian surfaces. This effect is calculated to test the validity of a Lambertian assumption used in remote sensing. For the three types of vegetations considered in this study, the assumption of Lambertian surface can be used satisfactorily in the derivation of surface reflectance from remotely measured radiance for a view angle outside the backscattering region. Within the backscattering region, however, the use of the assumption can result in a considerable error in the derived surface reflectance. Accuracy also deteriorates with increasing solar zenith angle. The angular distribution of the surface reflectance derived from remote measurements is smoother than that at the surface. The effect of surface non-Lambertianity on remote sensing of vegetation index is very weak. Since the effect is similiar in the visible and near infrared part of the solar spectrum for the vegetations treated in this study, it is canceled in deriving the vegetation index. The effect of the diffuse skylight on surface reflectance measurements at ground level is also discussed.

Lee, T. Y.↗

Highly mobile oxygen holes in magnesium oxide

High-purity MgO exhibits an unexpected giant anomaly of the apparent static dielectric constant and a positive surface charge of the order of 5 x 10 to the 21st/cu cm in the top 15 nm. It is postulated that the MgO matrix contains traces of peroxy defects, O2(2-), associated with Mg(2+) vacancies. Above approximately 400 C the O2(2-) dissociates to vacancy bound O(-) and highly mobile O(-) states, which diffuse to the surface, giving rise to a high surface conductivity.

Freund, Minoru M.↗

Liquid Water in the Extremely Shallow Martian Subsurface

Availability of liquid water is one of the major constraints for the potential Martian biosphere. Although liquid water is unstable on the surface of Mars due to low atmospheric pressures, it has been suggested that liquid films of water could be present in the Martian soil. Here we explored a possibility of the liquid water formation in the extremely shallow (1-3 cm) subsurface layer under low atmospheric pressures (0.1-10 mbar) and low ("Martian") surface temperatures (approx.-50 C-0 C). We used a new Goddard Martian simulation chamber to demonstrate that even in the clean frozen soil with temperatures as low as -25C the amount of mobile water can reach several percents. We also showed that during brief periods of simulated daylight warming the shallow subsurface ice sublimates, the water vapor diffuses through porous surface layer of soil temporarily producing supersaturated conditions in the soil, which leads to the formation of additional liquid water. Our results suggest that despite cold temperatures and low atmospheric pressures, Martian soil just several cm below the surface can be habitable.

Pavlov, A.↗

Whence cometh /and goeth/ Jupiter's high energy electrons

Jupiter's decimetric emission is universally identified as synchrotron radiation from about 10 MeV electrons. These electrons radiate away their energy in a few months and hence must be continuously replaced. A theory in which electrons are injected at Jupiter's magnetopause and radially diffuse toward the planetary surface, gaining energy in the process is summarized. The radial diffusion coefficient in the inner magnetosphere is determined. This diffusion coefficient, which also holds for protons, is sufficiently small that the inner Galilean satellites can wipe out large fractions of the incoming proton and electron fluxes. The reduction of the proton flux is extremely important to the survival of the Pioneer experimental payloads.

Birmingham, T. J.↗

Laminar Soot Processes (Lsp) Experiment: Findings From Ground-Based Measurements

Processes of soot formation and oxidation must be understood in order to achieve reliable computational combustion calculations for nonpremixed (diffusion) flames involving hydrocarbon fuels. Motivated by this observation, the present investigation extended earlier work on soot formation and oxidation in laminar jet ethylene/air and methane/oxygen premixed and acetylene-nitrogen/air diffusion flames at atmospheric pressure in this laboratory, emphasizing soot surface growth and early soot surface oxidation in laminar diffusion flames fueled with a variety of hydrocarbons at pressures in the range 0.1 - 1.0 atm.

Kim, C. H.↗

Determination of Interfacial Rheological Properties through Microgravity Oscillations of Bubbles and Drops

This report summarizes our derivations of analytical expressions for the frequencies and damping constants for small-amplitude axisymmetric shape oscillations of a liquid drop suspended in an immiscible fluid host in microgravity. In particular, this work addresses large Reynolds number shape oscillations and focuses on the surface rheological effects that arise from the presence of insoluble surfactants at the interface. Parameters characterizing viscous effects from the bulk phases, surface viscous effects, Marangoni effects from the surface advection and diffusion of surfactants, and the Gibbs elasticity are all considered and analyzed to determine the relative importance of each contribution. Supplementing the analytical treatment for small-amplitude oscillations, a numerical boundary integral equation formulation is developed for the study of large-amplittide axisymmetric oscillations of a drop in vacuum. The boundary integral formulation is an extension of classical potential flow theory and approximately accounts for viscous effects in the bulk fluid as well as the surface viscous and Marangoni effects resulting from an insoluble surfactant contaminating the interface. Theoretical and numerical results are presented for four distinct cases. These, range from the case when the effects of the surfactants are 'negligible' to 'large' when compared to the viscous effects in the bulk phases. The feasibility of the non-contact measurement of the surface parameters, using experimental observations for the oscillation frequencies and damping constants of drops and bubbles, is discussed.

Nadim, Ali↗

Effects of high doping levels on silicon solar cell performance

Open-circuit voltages measured in silicon solar cells made from 0.01 ohm-cm material are 150 mV lower than voltages calculated from simple diffusion theory and cannot be explained by poor diffusion lengths or surface leakage currents. An analytical study was made to determine whether high doping effects, which increase the intrinsic carrier concentration, could account for the low observed voltages and to determine the limits on voltage and efficiency imposed by high doping effects. The results indicate that the observed variation of voltage with base resistivity is predicted by these effects. A maximum efficiency of 19% (AMO) and a voltage of 0.7 volts were calculated for 0.1 ohm-cm cells assuming an optimum diffused layer impurity profile.

Godlewski, M. P.↗

Pt: Ti Diffusion Barrier, Interconnect, and Simultaneous Ohmic Contacts to n- and p-type 4H-SiC

We report the initial results of using co-sputtered Pt:Ti 80:20 at. % composition ratio metallization as a diffusion barrier against gold (Au) and oxygen (O), as an interconnect layer, as well as forming simultaneous ohmic contacts to n-and p-type 4H-SiC. Having a single conductor with such combined multi-functional attributes would appreciably reduce the fabrication costs, processing time and complexity that are inherent in the production of SiC based devices. Auger Electron Spectroscopy, Focused Ion Beam-assisted Field Emission Scanning Electron Microscopy and Energy Dispersive Spectroscopy analyses revealed no Au and O migration to the SiC contact surface and minimal diffusion through the Pt:Ti barrier layer after 15 minutes of exposure at 800 °C in atmosphere, thus offering potential long term stability of the ohmic contacts. Specific contact resistance values of 7 x 10(exp -5) and 7.4 x 10(exp -4) Ω-sq.cm were obtained on the n (N(sub d)=7 x 10(exp 18) per cu.cm and p (N(sub a)=2 x 10(exp 20) per cu. cm) -type 4H-SiC, respectively. The resistivity of 75 μΩ-cm was obtained for the Pt:Ti layer that was sandwiched between two SiO2 layers and annealed in pure O ambient up to 900 °C, which offers promise as a high temperature interconnect metallization.

Simultaneous Ohmic Contact↗

A potential-energy scaling model to simulate the initial stages of thin-film growth

A solid on solid (SOS) Monte Carlo computer simulation employing a potential energy scaling technique was used to model the initial stages of thin film growth. The model monitors variations in the vertical interaction potential that occur due to the arrival or departure of selected adatoms or impurities at all sites in the 400 sq. ft. array. Boltzmann ordered statistics are used to simulate fluctuations in vibrational energy at each site in the array, and the resulting site energy is compared with threshold levels of possible atomic events. In addition to adsorption, desorption, and surface migration, adatom incorporation and diffusion of a substrate atom to the surface are also included. The lateral interaction of nearest, second nearest, and third nearest neighbors is also considered. A series of computer experiments are conducted to illustrate the behavior of the model.

Heinbockel, J. H.↗

Film boiling of mercury droplets

Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. Diffusion from the upper surface of the drop appears as a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

Baumeister, K. J.↗

Surface Radiation Budget (SRB) Release 2 Shortwave 3 hourly Data in Native Format (SRB_REL2_SW_3HRLY)

The SRB data include the average upward and downward fluxes, photosynthetically active radiative flux, aerosol and cloud optical depth, cloud fraction, and solar zenith angle measured at three hourly intervals for each day for the entire globe between 07/01/1983 and 10/31/1995. These SW surface radiative parameters were derived with the Shortwave algorithm of the NASA World Climate Research Programme/Global Energy and Water-Cycle Experiment (WCRP/GEWEX) Surface Radiation Budget (SRB) Project. [Location=GLOBAL] [Temporal_Coverage: Start_Date=1983-07-01; Stop_Date=1998-07-26] [Spatial_Coverage: Southernmost_Latitude=-90; Northernmost_Latitude=90; Westernmost_Longitude=-180; Easternmost_Longitude=180] [Data_Resolution: Latitude_Resolution=1 degree; Longitude_Resolution=Ranges from 1 degree (tropics and subtropics) to 120 degrees (the poles).; Temporal_Resolution=3 hourly; Temporal_Resolution_Range=3 hourly].

ALL SKY SW SURFACE DOWNWARD DIFFUSE FLUX↗

The Decomposition of Carbonates and Organics on Mars

The return and analysis of pristine material that is relict of a putative period of chemical evolution is a fumdamental goal of the exobiological exploration of Mars. In order to accomplish this objective, it is desirable to find oxidant-free regions where pristine material can be accessed at the shallowest possible depth (ideally directly from the surface). The objective of our ongoing research is to understand the spatial and temporal distribution of oxidants in the martian regolith and the redox chemistry of the soil; in effect to understand the chemical mechanisms and kinetics relating to the in-situ destruction of organics and the formation of the reactive species responsible for the Viking biology results. In this work, we report on experimental studies of oxidizing processes that may contribute to carbonate and organic degradation on Mars. Organic molecules directly exposed to solar UV may decomposed either directly into CO2, or into more volatile organic fragments. Organic macromolecules not directly exposed to high UV flux are most likely to be affected by atmospheric oxidants which can diffuse to their surfaces. The oxidizing processes examined include: gas-phase oxidants, UV photolysis, and UV-assisted heterogeneous catalysis. For example, assuming a meteroritic infall rate of 4 x 10(exp -4) g/m^2yr (Flynn and McKay 1990) and a flux of organic carbon of 2 x 10(exp -5) g/m^2yr, laboratory measurements of the UV-assisted decomposition of benzenehexacarboxylic acid (mellitic acid, a likely intermediate of kerogen oxidation), indicate its decomposition rate on Mars would exceed the total flux of organic carbon to the planet by over four orders of magnitude. Our measurements indicate that although the decomposition temperature of kerogens in some cases exceeds the temperature limit of the Viking GCMS, it is unlikely kerogens or their decomposition intermediates were present at the Viking landings sites at levels above the GCMS detection limits.

Quinn, Richard C.↗

Simultaneous Retrieval of Aerosol and Surface Optical Properties from Combined Airborne- and Ground-Based Direct and Diffuse Radiometric Measurements

This paper presents a new method for simultaneously retrieving aerosol and surface reflectance properties from combined airborne and ground-based direct and diffuse radiometric measurements. The method is based on the standard Aerosol Robotic Network (AERONET) method for retrieving aerosol size distribution, complex index of refraction, and single scattering albedo, but modified to retrieve aerosol properties in two layers, below and above the aircraft, and parameters on surface optical properties from combined datasets (Cloud Absorption Radiometer (CAR) and AERONET data). A key advantage of this method is the inversion of all available spectral and angular data at the same time, while accounting for the influence of noise in the inversion procedure using statistical optimization. The wide spectral (0.34-2.30 m) and angular range (180 ) of the CAR instrument, combined with observations from an AERONET sunphotometer, provide sufficient measurement constraints for characterizing aerosol and surface properties with minimal assumptions. The robustness of the method was tested on observations made during four different field campaigns: (a) the Southern African Regional Science Initiative 2000 over Mongu, Zambia, (b) the Intercontinental Transport Experiment-Phase B over Mexico City, Mexico (c) Cloud and Land Surface Interaction Campaign over the Atmospheric Radiation Measurement (ARM) Central Facility, Oklahoma, USA, and (d) the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) over Elson Lagoon in Barrow, Alaska, USA. The four areas are dominated by different surface characteristics and aerosol types, and therefore provide good test cases for the new inversion method.

Gatebe, C. K.↗