Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface functionalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Thiol–ene Click Chemistry Incorporates Hydroxyl Functionality on Polycyclooctene to Tune Properties

Polyolefins compose the majority of plastic waste, but conventional mechanical recycling degrades their properties, thereby reducing their value. We report the functionalization of a model for dehydrogenated polyethylene, polycyclooctene (PCOE), with thiol–ene click chemistry to install pendant hydroxyl ethyl thioethers. Functionalization of PCOE using mercaptoethanol via thiol–ene click chemistry yielded functionalization between 1.4 and 22.9% based on ethylene monomeric units. Reactions were well-controlled by varying the reagent stoichiometry and reaction time. Crystallinity and melting temperature decreased, and glass transition temperature increased with greater functionalization. Contact angle measurements reveal an increase in surface polarity with functionalization. Here, comparisons with poly(ethylene-co-vinyl alcohol) (EVOH) show comparable surface polarity at similar levels of alcohol functionalization. At 12% functionalization, the ultimate shear stress (USS) of functionalized PCOE in an adhesive configuration is 4.10 ± 0.48 MPa, comparable to EVOH. At >12% functionalization, the failure mode changed from adhesive to mixed adhesive–cohesive, and the USS decreased.

36 MATERIALS SCIENCE↗
DOE OSTI2022

What can surface wind observations tell us about interannual variation in wind energy output?

The past decade of wind power growth was supported by capacity factor improvements and associated cost reductions. But are higher capacity factors a technology success story or, as suggested by recent research, has the influence of technology been overstated by ignoring positive surface wind speed trends? The answer could influence estimates of wind energy's cost and even future deployment rates. We find that US surface wind speed observations imply a 2.6% improvement in capacity factors from 2010 to 2019. Yet newer vintages of wind plants have recorded capacity factors that are ~25% larger than plants built close to 2010. It follows that technological factors and improved site quality, not higher wind speeds, drove most of the improvement in capacity factors. Additionally, we match hundreds of meteorological stations to nearby (< 25 km) wind plants and compare annual estimated generation, based on a function of surface wind speed observations, to annual recorded generation. Researchers rely on this publicly available surface data because measurements co-located with wind plants are generally considered proprietary. Our analysis addresses a research gap: interannual variation in observed surface wind speeds is rarely compared to observed data at wind plant locations and turbine heights. We find that despite its common use for this purpose, generation estimates based on publicly available surface observational data provide a poor proxy for interannual variability in recorded wind generation. These findings suggest that caution is generally needed when researchers use surface wind speed measurements to investigate long-term wind energy trends.

17 WIND ENERGY↗
DOE OSTI2021

Covalent Functionalization of Nickel Phosphide Nanocrystals with Aryl-Diazonium Salts

Covalent functionalization of Ni 2 P nanocrystals was demonstrated using aryl-diazonium salts. Spontaneous adsorption of aryl functional groups was observed, with surface coverages ranging from 20 to 96% depending on the native reactivity of the salt as determined by the aryl substitution pattern. Increased coverage was possible for low reactivity species using a sacrificial reductant. Functionalization was confirmed using thermogravimetric analysis, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The structure and energetics of this nanocrystal electrocatalyst system, as a function of ligand coverage, were explored with density functional theory calculations. The Hammett parameter of the surface functional group was found to linearly correlate with the change in Ni and P core-electron binding energies and the nanocrystal's experimentally and computationally determined work function. The electrocatalytic activity and stability of the functionalized nanocrystals for hydrogen evolution were also improved when compared to the unfunctionalized material, but a simple trend based on electrostatics was not evident. Density functional theory was used to understand this discrepancy, revealing that H adsorption energies on the covalently functionalized Ni 2 P also do not follow the electrostatic trend and are predictive descriptors of the experimental results.

14 SOLAR ENERGY↗
DOE OSTI2024

Ultrathin Magnesium-Based Coating as an Efficient Oxygen Barrier for Superconducting Circuit Materials

Scaling up superconducting quantum circuits based on transmon qubits necessitates substantial enhancements in qubit coherence time. Over recent years, tantalum (Ta) has emerged as a promising candidate for transmon qubits, surpassing conventional counterparts in terms of coherence time. However, amorphous surface Ta oxide layer may introduce dielectric loss, ultimately placing a limit on the coherence time. In this study, a novel approach for suppressing the formation of tantalum oxide using an ultrathin magnesium (Mg) capping layer is presented. Synchrotron-based X-ray photoelectron spectroscopy studies demonstrate that oxide is confined to an extremely thin region directly beneath the Mg/Ta interface. Additionally, it is demonstrated that the superconducting properties of thin Ta films are improved following the Mg capping, exhibiting sharper and higher-temperature transitions to superconductive and magnetically ordered states. Moreover, an atomic-scale mechanistic understanding of the role of the capping layer in protecting Ta from oxidation is established based on computational modeling. Further, this work provides valuable insights into the formation mechanism and functionality of surface tantalum oxide, as well as a new materials design principle with the potential to reduce dielectric loss in superconducting quantum materials. Ultimately, the findings pave the way for the realization of large-scale, high-performance quantum computing systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structure and energetics of the elbows in the Au(111) herringbone reconstruction

We study the structure of the threading edge dislocations, or “elbows,” which are an essential component of the well-known herringbone reconstruction of the (111) surface of Au. Previous work had shown that these dislocations can be stabilized by long-range elastic relaxations into the bulk. However, the validity of the harmonic spring model that had been used to estimate the energies of the dislocations is uncertain. To enable a more refined model of the dislocation energetics, we have imaged the atomic structure of these dislocations using scanning tunneling microscopy. We find that the harmonic spring model does not adequately reproduce the observed structure. We are able to reproduce the structure, however, with a two-dimensional Frenkel-Kontorova (FK) model that uses a pairwise Morse potential to describe the interactions between the top layer Au atoms on a rigid substrate. The parameters of the potential were obtained by fitting the energy of uniaxially compressed phases, or “stripes”, computed with density functional theory, as a function of surface Au density. Within this model, the formation of the threading dislocations remains unfavorable. However, the large forces on the substrate atoms near the threading-dislocation cores, render the assumption of a completely rigid substrate questionable. Indeed, if the FK parameters are modified to account for the relaxation of just one more atomic layer, threading dislocations can, in principle, become favorable, even without bulk elastic relaxations. Additional evidence for a small elbow energy is that our computed change in the Au(111) surface stress tensor caused by the (√ 3 × 22) reconstruction is considerably smaller than previous estimates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Programmable Phase Selection between Altermagnetic and Noncentrosymmetric Polymorphs of MnTe on InP via Molecular Beam Epitaxy

This dataset contains DFT input and output files supporting the theoretical modeling in the associated publication (ACS Appl. Mater. Interfaces 2026, 18, 15654-15664). The calculations model the interfacial energetics of two MnTe polymorphs — NiAs-MnTe (hexagonal, alpha phase) and ZnS-MnTe (cubic, gamma phase) — on InP(111) substrates with two surface terminations: In-terminated InP(111)A and P-terminated InP(111)B. This gives four interface configurations: NiAs on In-terminated (experimentally observed), NiAs on P-terminated (computed for comparison), ZnS on In-terminated (computed for comparison), and ZnS on P-terminated (experimentally observed). The dataset is organized into four calculation types, each covering all four polymorph/termination combinations: (i) Slabs: Pristine MnTe/InP heterostructure slabs used to compute total energies and interface energy densities (Eint) for all four configurations, as reported in Fig. 6 of the main text. (ii) Disorder: Same slab geometries with a P_Te + Te_P antisite defect pair introduced near the interface, used to assess chemical intermixing effects on interface stability (Fig. S8, SI). (iii) Strain: Pristine slab calculations with in-plane lattice parameters strained by -1% and +1% relative to the InP lattice constant, used to evaluate strain-dependent interface energetics (Fig. S9, SI). (iv) Charge_Density: Single-point calculations on the full heterostructure, the isolated InP slab, and the isolated MnTe slab at fixed geometry, used to compute differential charge density plots showing interfacial charge accumulation and depletion as a function of surface termination (Fig. S10, SI). Each calculation folder contains INCAR, KPOINTS, POSCAR, CONTCAR, OUTCAR, and POTCAR_info.txt (PAW potential information, excluding the full POTCAR due to VASP licensing restrictions). The calculations were performed using VASP 6.4.3 with PBE exchange-correlation, PAW potentials, a Hubbard correction of Ueff = 5 eV on Mn d-states, and A-type AFM spin initialization.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nano zero valent iron electrodeposition at boron doped diamond electrodes

Here, in this study, we present an ecofriendly and simple electrochemical method for synthesizing nano zero-valent iron particles (nZVIs) directly on boron-doped diamond (BDD) electrode surfaces. A BDD electrode served as the substrate for electrodeposition using a 5 mM FeCl 3 /0.1 M KCl solution and chronoamperometry at an applied potential of −1.3 V versus Ag/AgCl (1 M KCl), as determined by cyclic voltammetry (CV) and supported by Pourbaix diagram analysis. The electrochemical behavior and surface modification were characterized using CV, electrochemical impedance spectroscopy (EIS), and surface analysis and microscopy techniques. The results confirm that BDD electrodes can serve as effective platforms for a controlled deposition of 56 nm nZVIs, offering a promising strategy for the development of advanced materials for environmental remediation, catalysis, and sensing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Casing Annulus Monitoring of CO 2 Injection Using Wireless Autonomous Distributed Sensor Networks

Effective and secure carbon subsurface storage, involving the deep underground injection of CO 2 into geological formations where it is permanently trapped, is paramount to mitigating CO 2 emissions (Figure I). Ensuring the integrity of these storage sites and detecting potential leakage through the casing annulus necessitates robust monitoring. This work provides the first integrated demonstration of a wireless casing-annulus monitoring architecture that can operate in highly attenuating cement-brine environments relevant to CO 2 storage. This project focused on developing and validating a novel sensor system for integration with autonomous monitoring near the cement reservoir interface. The goal was a fully integrated Technology Readiness Level (TRL) 4/5 field validation of a distributed wireless intelligent sensor system providing real-time, direct subsurface formation measurements to enhance fluid movement monitoring in the cemented casing annulus. Achieving this objective required the development and integration of 1) wireless autonomous microsensor technology by California Institute of Technology (Caltech); 2) sensor packaging and emplacement technology by Research Triangle Institute (RTI); and 3) smart well completions using wireless active casing collars and NOV pipe by the Sandia National Lab (SNL). The collaboration with the Caltech team in this project aimed to develop millimeter-scale radio frequency identification (RFID) sensors capable of detecting CO 2 , pH, and/or methane levels. These sensors are engineered to be impervious to fluids, allowing them to be mixed with cement and installed within the casing annulus. They operate using RFID protocols at frequencies of 902–928 MHz for both power and communication. A Sandia National Laboratories’ team engaged their expertise in the development of a Smart Collar system designed for the wireless data collection from these RFID sensors embedded in the cement annulus and transmission of this information to the ground surface via IntelliPipe/IntelliServ NOV drill pipe. This is accomplished through inductive coupling at the collar, which facilitates data transfer through each segment of the pipe. Because the system cannot transmit a direct current signal to power the Smart Collar, both power and communication were implemented using alternating current and electromagnetic signals at varying frequencies. Furthermore, the developed microsensor technology had to be demonstrated and validated in comparison with reference transducer measurements in a field test site at The University of Texas at Austin (UT-Austin). Although the full sensor suite did not reach field-deployment readiness, the system-level integration achieved in this project establishes a validated pathway for future incorporation of advanced microsensors.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Spin-dependent charge transmission through chiral 2T3N self-assembled monolayer on Au

In this study, a gold surface is functionalized by chemisorption of the enantiopure N,N'-bis-[2,2';5',2"]tert-thiophene-5-yl methylcyclohexane-1,2-diamine (2T3N), a chiral oligothiophene derivative, via overnight incubation in a 2T3N ethanol solution. The Au|2T3N interface is characterized by x-ray photoelectron circular dichroism and comparing x-ray photoemission spectroscopy and electro-desorption results. Charge transmission at the Au|2T3N| solution interface is characterized by recording the cyclic voltammetry of the Fe(III)/Fe(II) reversible redox couple, finding a charge transfer rate constant, k°, variation from 1 × 10 -1 to 3.3 × 10 -2 cm s -1 , when comparing the bare Au and the Au|2T3N interfaces, respectively. The “anomalous” high value of k° found for the chiral Au|2T3N interface can be rationalized on the basis of the chiral-induced spin selectivity effect, as further proved by magnetic–conductive atomic force microscopy measurements at room temperature. A spin polarization of about 30% is found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Designing Physicochemically‐Ordered Interphases for High‐Performance Composites

To enhance the mechanical properties of carbon fiber‐reinforced polymer composites, a physicochemical scaffold is designed incorporating microscopically architected chemically reactive nanofibers that act as a multiscale bridge between the carbon fibers and the matrix. Thermally activated nanofibers leverage their morphologically driven mechanochemical properties to form covalent bonds with adjacent polymer molecules, creating a co‐continuous network that dramatically enhances fiber‐matrix load transfer. By meticulously controlling the nanofiber architecture through variable surface area, functional group availability, and polymer chain alignment effects, the extent of covalent bonding between nanofibers and the matrix is manipulated ultimately resulting in improved carbon fiber‐matrix adhesion. Further, the concept was validated using polyacrylonitrile nanofibers within an acrylonitrile butadiene styrene matrix in a discontinuous carbon fiber‐reinforced composite system. Nanomechanical studies using atomic force microscopy and low‐field nuclear magnetic resonance spectroscopy confirmed immobilized, chemically transferred, and ordered nanostructures at the interphase. The resulting composites demonstrated ≈56% and ≈175% improvements in tensile strength and toughness, respectively, compared to composites without nanofiber. Comprehensive thermal, rheological, and X‐ray scattering analyses, along side all‐atomic molecular dynamics simulations, revealed the fundamental mechanisms behind these improvements in mechanical behavior. The versatility and efficacy of the approach have the potential to address longstanding interphase challenges in the composite industry.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Estimation of isosteric heat of adsorption from generalized Langmuir isotherm

Simulation and design of adsorptive separation units demand accurate estimation of thermodynamic properties. Isosteric heat of adsorption as calculated from generalized Langmuir (gL) isotherm coupled with Clausius-Clapeyron expression for pure component and mixed-gas adsorption equilibria is presented in this work. The estimated isosteric heat of adsorption as functions of surface loading and composition is validated against the experimental data for various adsorption systems. Furthermore, the gL results are compared against classical Langmuir (cL) and Toth isotherm for pure components and with Ideal Adsorbed Solution Theory (IAST) for mixed-gas adsorption equilibria. Furthermore, the comparison highlights that gL outperforms cL and Toth for pure component adsorption and IAST for mixed-gas adsorption, and gL reliably captures the loading dependence and the composition dependence for isosteric heat of adsorption.

42 ENGINEERING↗
DOE OSTI2020

Localized corrosion at nm-scale hardening precipitates in Al-Cu-Li alloys

The localized corrosion of Li-containing nm hardening precipitates in the 3rd generation of Al-Cu-Li alloys was investigated based on a quasi in situ approach by sequentially exposing the material to NaCl solution and characterizing the structural, chemical, and electrochemical evolution at atomic scale using electron microscopy, spectroscopy, 3D tomography, electrochemical measurements, and DFT calculations. Localized corrosion of Al 7.5 Cu 4 Li (TB phase) initiated along {001} family of planes through the dealloying of Al and Li due to a low surface work function. Cu was enriched along the Cu (110) // T B (011) // Al (100) orientations on and around corroded T B precipitates. No strong galvanic interactions were observed at the T B and Al matrix interface due to the formation of a Li-C-O rich passivation layer during electrolyte exposure. Similarities and differences between T B and other common Al-Cu-Li precipitates (Al 2 CuLi, Al 6 CuLi 3 , and Al 3 Li) with respect to corrosion are discussed. Overall, the reported corrosion mechanism can assist in the assessment of the localized corrosion susceptibility of precipitation-hardened Al alloys and assist in the design of new alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Vapor-phase self-assembly for generating thermally stable single-atom catalysts

Preparation of thermally stable metal single-atom catalysts (SACs) is a challenge in heterogeneous catalysis, especially on conventional supports that provide a weak metal-support interaction. In this work, we report that a modified support MgAl 2 O 4 can stabilize Pt single atoms by a mechanism of vapor-phase self-assembly in a high-temperature treatment (800°C, air). The experimental results on the formation mechanism and the structure are validated by DFT and ab initio molecular dynamics simulations. We infer that stable triangular K 3 O 3 structures help stabilize Pt single atoms at high temperatures in oxidizing conditions, exhibiting excellent reactivity for methane oxidation. The obtained Pt/K/MgAl 2 O 4 SAC presents excellent stability in methane oxidation after steam treatment at elevated temperatures, whereas the Pt/MgAl 2 O 4 nanocatalyst suffers from rapid deactivation due to Pt nanoparticle growth. Now this work paves the way for preparing thermally stable and highly active SACs using conventional high-surface-area supports, despite the weak metal-support interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Bioinspired design toward nanocellulose-based materials

Nature provides lots of inspiration for material and structural design for various applications. Deriving design principles from the investigation of nature can provide a rich source of inspiration for the development of multifunctional materials. The bioinspired design templates mainly include mussels, nacre, and various plant species. As a sustainable and renewable feedstock, nanocellulose can be used to fabricate advanced materials with multifunctional properties through bioinspired designs. However, challenges and opportunities remain for realizing the full potential in the design of novel materials. Here, this article reviewed recent development in the bioinspired nanocellulose based materials and their application. This article summarizes the functions (e.g., surface wetting) and applications (e.g., composite) of bioinspired nanocellulose-based materials. The bioinspired design templates are discussed along with strategies, advantages, and challenges to the development of synthetic mimics. Additionally, mechanisms and processes (e.g., chemical modification, self-assembly) leading to biomimetic design are discussed. Finally, future research directions and opportunities of bioinspired nanocellulose-based materials are highlighted.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Advances and perspectives of hard carbon anode modulated by defect/hetero elemental engineering for sodium ion batteries

Sodium-ion batteries (SIBs) serve as a promising complement to lithium-ion batteries for large-scale energy storage, leveraging the abundance of sodium resources and notable safety advantages. The key advancement in SIB industrialization hinges on identifying a cost-effective and high-performance anode material, similar to the graphite anode in lithium-ion batteries. Hard carbon emerges as prime anode materials for SIBs, boasting high specific capacity, low sodium storage potential, and wide availability. However, practical applications of hard carbon encounters challenges such as low initial Coulombic efficiency (ICE), inadequate long-term cycling stability, and poor rate performance. Recent research has focused on the optimization of hard carbon electrodes through functional design. In this comprehensive review, we have meticulously examined the progress in enhancing sodium storage performance through microstructural modulation within hard carbon, encompassing four pivotal aspects: heteroatom doping, incorporation of oxygen functional groups, surface coating, and intrinsic defect engineering. Progress in implementing these strategies is scrutinized, while the merits and challenges of each defect engineering approach are discussed. In conclusion, this review also looks into forthcoming opportunities and challenges in the practical application process of hard carbon electrodes in SIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Mitigation of safety and environmental challenges posed by refrigerants

The abatement of safety and environmental burden associated with low and ultra-low Global Warming Potential (GWP) refrigerants is a critical undertaking. As the industry shifts towards more environmentally friendly alternatives, mitigating the potential risks and ensuring safety standards becomes paramount. The adoption of mildly and highly flammable refrigerants contributes significantly to minimizing the greenhouse gas impact on the environment, aligning with global climate and sustainability goals. However, it is essential to address safety concerns and potential environmental implications associated with the end use of these refrigerants. A method to mitigate the safety risk in a flammable refrigerant based heating, ventilation, air-conditioning, and refrigeration (HVACR) system is the primary focus of this paper. Advent of A2L and A3 refrigerants as replacements to high GWP refrigerants requires careful handling of leak episodes to lower or eliminate the risk associated with creating flammable mixtures capable of fire/explosion hazard. Solid materials tailored to target the molecule of interest (i.e., refrigerant.) by engineering the microporous structure as well as chemically functionalizing the surface to attract and hold on to the chemical compound being removed from the gas stream was realized. Quantitative analysis reveals the adsorbent's effectiveness in reducing leak potential in the range of 40 %–100 % for various refrigerants. Strategic placement and active leak management with negative pressure offer promising avenues for capturing leaked refrigerants, enhancing overall safety.

42 ENGINEERING↗
DOE OSTI2020

Transport of colloidal particles in microscopic porous medium analogs with surface charge heterogeneity: experiments and fundamental role of single-bead deposition

Understanding colloid transport in subsurface environments is challenging due to complex interactions between colloids, ground water, and porous media over several length scales. Here, we study the transport of colloidal particles through bead-assembled microfluidic porous media analogs (PMAs) with surface charge heterogeneity. The pore-scale dynamics of colloidal particle deposition were measured, as well as the breakthrough curves (BTC) and retention profiles (RP) of deposited colloidal particles at the scale of the entire PMA. From pore-scale experiments, the maximum surface coverage (?max = 0.51) was measured directly, from which the surface blocking function and deposition coefficient (kpore = 3.56 s-1) were obtained. Using these pore-scale parameters, the transport of colloidal particles was modeled using a one-dimensional advection-dispersion equation under the assumption of irreversible adsorption between oppositely charged beads and colloids, showing good agreement with experimental data. This work presents a new approach to fabricate chemically heterogeneous porous media in a microfluidic device that enables direct measurements of pore-scale colloidal deposition. The approach allows a quantitative prediction of colloidal breakthrough and retention via coupling of direct measurements and an advection-dispersion-deposition model.

Guo, Yang↗
DOE OSTI2026

Tuning Anisotropic Optical Properties of Inorganic and Hybrid Organic–Inorganic MXenes via Topochemical Surface Modification

Surface groups are central to the properties of MXenes, yet their role in optical anisotropy remains largely unexplored. Here, we use a topochemical route to synthesize single crystals of stacked Ti 3 C 2 Cl 2 and hybrid organic–inorganic MXenes (h-MXenes) with lateral sizes of 38–75 μm, rotational registry, and tunable interlayer spacing. Solid-state NMR spectroscopy shows that topochemical substitution generates mixed amido, imido, and hydride surface motifs, which modify the electronic structure of the Ti 3 C 2 inorganic core. Imaging spectroscopic ellipsometry with micron-scale spatial resolution enables reconstruction of the complex dielectric tensor of individual multilayer crystals. Ti 3 C 2 Cl 2 exhibits a type-II hyperbolicity above 930 nm, whereas h-MXenes do not display hyperbolicity within the measured 300–1700 nm window, instead showing reduced in-plane conductivity, suppressed out-of-plane light absorption, and a chain-length-dependent blue shift of a near-infrared absorption feature. These results demonstrate topochemical surface modification as a direct handle for engineering MXenes as surface-programmable optical media.

Hybrid materials↗