Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface layering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Near surface inversion layer recombination in Al{sub 2}O{sub 3} passivated n-type silicon

On n-type silicon, negatively charged surface passivation layers create a near surface recombination channel, which could significantly reduce the effective carrier lifetime at low injection levels (Δn < 10{sup 14 }cm{sup −3}). This effect is described by Shockley Read Hall recombination at homogeneously distributed defects in the silicon wafer. In the near surface region, fixed charges in the dielectric layer significantly change the carrier concentrations and the recombination rate of defects. Sentaurus device simulations show that the contribution of the near surface recombination to the effective carrier lifetime depends on the properties of the involved defects. The lifetime reduction is strongest when the involved defects have an energy level in the lower half of the band gap and a very high electron to hole capture cross section ratio. For the simulation, a very low defect density in the order of 10{sup 8 }cm{sup −3} is assumed, which is a realistic value in highly pure float zone silicon. Quasi-steady state photoconductance measurements on n-type silicon with Al{sub 2}O{sub 3} passivation are done and fitted with the recombination model. Very good correlation between simulation and experiment is achieved when the involved recombination centers have an electron to hole capture cross section ratio of 10{sup 7} and an energy level of −0.2 eV w.r.t. the intrinsic level. The simulated defect properties are discussed in respect of transition metal and doping related defects reported in literature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the Size Dependence of Molar and Specific Properties of Independent Nano-phases and Those in Contact with Other Phases

Nano-materials are materials with at least one nano-phase. A nano-phase is a phase with at least one of its dimensions below 100 nm. It is shown here that nano-phases have at least 1% of their atoms along their surface layer. The ratio of surface atoms is proportional to the specific surface area of the phase, defined as the ratio of its surface area to its volume. Each specific/molar property has its bulk value and its surface value for the given phase, being always different, as the energetic states of the atoms in the bulk and in the surface layer of a phase are different. The average specific/molar property of a nano-phase is modeled here as a linear combination of the bulk and surface values of the same property, scaled with the ratio of the surface atoms. That makes the performance of all nano-phases proportional to their specific surface area. As the characteristic size of the nano-phase is inversely proportional to its specific surface area, all specific/molar properties of nano-phases are inversely proportional to the characteristic size of the phase. This is applied to the size dependence of the molar Gibbs energy of the nano-phase, which appears to be in agreement with the thermodynamics of Gibbs. This agreement proves the general validity of the present model on the size dependence of the specific/molar properties of independent nano-phases. It is shown that the properties of nano-phases are different for independent nano-phases (surrounded only by their equilibrium vapor phase) and for nano-phases in multi-phase situations, such as a liquid nano-droplet in the sessile drop configuration.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermally driven diffusion of SO2 within the surface of Io

The presence of sulfur dioxide (SO2) on Io, together with the fact that the surface layer of Io has extremely high porosity, suggests the possibility of diffusion of this volatile within the surface, as well as exchange between the surface and an atmosphere. The former possibility is investigated through the development of a surface layer thermal model and subsequent calculations of the thermally driven diffusion flux of SO2 within the layer. The major factors affecting the diffusion process are the temperature and temperature gradient in the surface layer throughout the day, and the porosity and grain size in the surface layer. The results indicate that the net transport of SO2 in the near-surface region is downward into the subsurface, causing near-surface depletion of SO2. Near-surface depletion would result in a layer of reduced thermal inertia overlying the bulk of the surface, consistent with thermal eclipse observations of Io. For the present nominal model with 10-micron grains and a porosity of 85 percent, the peak net diurnal downward flux reaches nearly 0.008 g/sq cm per period.

Meade, Paul E.↗

Chromium segregation at phase boundaries in Cr-doped WC-Co cemented carbides

Highlights: • Experimental evidence of a mixed (W,Cr) carbide layer on WC grain surfaces • Evidence of Cr segregation in the Co-rich binder phase in front of WC grain surfaces • Temperature dependent equilibrium segregation of Cr estimated from atom probe data • Experimental observations supported by predictions from thermodynamic modelling - Abstract: Atom probe tomography has shown (Cr,W)C to be present as a thin WC grain surface layer in an as-sintered Cr-doped WC-Co cemented carbide microstructure slowly cooled from the sintering temperature. The Co-rich binder phase contained a segregation of Cr in front of this surface layer. The mixed carbide layer was not observed when the as-sintered material had been heat treated at 1000 °C for 3000 s and then quickly cooled. A reduced amount of segregated Cr was, however, still present in the binder phase in front of the WC grain surface. These observations are supported by predictions from thermodynamic modelling; (Cr,W)C becomes stable at temperatures below 940 °C in the absence of other secondary carbides. The equilibrium segregation of Cr in the binder phase was estimated to 0.8 and 0.4 monolayer in the as-sintered and heat treated materials, respectively. The energy of segregation was calculated to 0.22 eV/Cr atom from the atom probe data. This value would result in a Cr segregation of 0.3 monolayer at the sintering temperature 1410 °C, provided that the energy of segregation in the Co-rich liquid phase sintering medium is the same as in the Co-rich binder phase. This Cr segregation may explain the WC grain growth inhibiting effect of Cr additions to WC-Co cemented carbide materials.

36 MATERIALS SCIENCE↗

The boundary layer of Mars: Fluxes, stability, turbulent spectra, and growth of the mixed layer

Spectra of wind from high-frequency measurements in the Martian atmospheric surface layer, along with the diurnal variation of the height of the mixed surface layer, are calculated for the first time for Mars. Heat and momentum fluxes, stability, and z(sub 0) are estimated for early spring from a surface temperature model and from Viking Lander 2 temperatures and winds at 44 deg N, using Monin-Obukhov similarity theory. Flow distortion by the lander is also taken into account. Model spectra for two measuring heights and three surface roughnesses are calculated using the depth of the mixed layer and the surface-layer parameters. These experiments indicate that z(sub 0) probably lies between 1.0 and 3.0 cm, and most likely is closer to 1.0 cm. The spectra are adjusted to simulate aliasing and high-frequency rolloff, the latter caused by both the sensor response and the large Kolmogorov length on Mars. Since the spectral models depend on the surface parameters, including the estimated surface temperature, their agreement with the calculated spectra indicates that the surface-layer estimates are self-consistent. This agreement is especially noteworthy in that the inertial subrange is virtually absent in the Martian atmosphere at this height, due to the large Kolmogorov length scale. These analyses extend the range of applicability of terrestrial results and demonstrate that it is possible to estimate the effects of severe aliasing of wind measurements, to produce models that agree well with the measured spectra. The results show that similarity theory developed for Earth applies to Mars, and that the spectral models are universal.

Tillman, James E.↗

Organic light emitting diode with surface modification layer

An organic light emitting diode (10) includes a substrate (12) having a first surface (14) and a second surface (16), a first electrode (32), and a second electrode (38). An emissive layer (36) is located between the first electrode (32) and the second electrode (38). The organic light emitting diode (10) further includes a surface modification layer (18). The surface modification layer (18) includes a non-planar surface (30, 52).

36 MATERIALS SCIENCE↗

Wind Conditions for Solar Energy Facility Design Based on Field Measurements at Nevada Solar One

This study characterises near-surface wind conditions at the Nevada Solar One (NSO) concentrated solar power plant using two years of measurements from a 15-m mast located 30 m west of the solar arrays. The surrounding terrain is fairly flat within 3 km, but nearby solar photovoltaic (PV) and concentrated solar power (CSP) installations introduce strong directional wind inhomogeneity, which motivates a sector-based analysis that distinguishes undisturbed inflow from waked flow. The analysis uses data from three sonic anemometers to assess whether turbulence in the surface layer can be represented as Gaussian and whether standard surface-layer scaling remains valid below 10 m height. The roughness length and displacement height are estimated for twelve directional sectors under near-neutral wind conditions, and all three velocity components show departures from Gaussian behaviour. Spectral analysis indicates that the turbulence contains low-frequency fluctuations with amplitudes higher than those predicted by standard models such as the Kaimal model or the Simiu and Scanlan model. The study introduces a new turbulence spectral model based on the eddy-surface-layer framework to better represent near-surface wind turbulence. The analysis further quantifies the influence of the surrounding power plants on mean wind profiles, one-point spectra, and vertical coherence for all velocity components. The solar collector arrays located 30 m east of the mast significantly modify the turbulence structure, whereas PV installations situated a few hundred metres away have only a limited influence on the turbulence measured at the mast. These findings highlight the limitations of conventional turbulence models for near-surface wind over solar infrastructure and provide improved parameterisations to support the structural design. The implications for the structural response of parabolic troughs and PV modules to such turbulence remain uncertain and require further investigation.

14 SOLAR ENERGY↗

Longtime Durability of PMR-15 Matrix Polymer at 204, 260, 288, and 316 C

Isothermal weight loss studies at the Glenn (Lewis) Research Center were conducted at four temperatures (204, 260, 288, and 316 C) with specimens of varied geometric shapes to investigate the mechanisms involved in the thermal degradation of PMR-15. Both neat resin behavior and composite behaviors were studied. Two points of interest in these studies are the role(s) of oxygen in the mechanisms involved in the thermo-oxidative degradation of these composite materials and the dimensional changes that occur during their useable lifetime. Specimen dimensional changes and surface layer growth were measured and recorded. It was shown that physical and chemical changes take place as a function of time and location in PMR-15 neat resin and composites as aging takes place in air at elevated temperatures. These changes initiate at the outer surfaces of both materials and progress inward following the oxygen as it proceeds by diffusion into the central core of each material. Microstructural changes cause changes in density, material shrinkage (strains), glass transition temperature, dimension, dynamic shear modulus, and compression properties. These changes also occur slowly dividing the polymer material into two distinct parts: a visibly undamaged core section between two visibly damaged surface layers. The surface layer has a significant effect on compression properties of thinner specimens, but the visibly undamaged core material controls these properties for specimens having eight or more plies. It was demonstrated that there are three different mechanisms involved in the degradation of PMR-15 during aging at elevated temperatures. These are a weight gain, a small weight fraction bulk material weight loss, and a large mass fraction weight loss concentrated at the surface of the polymer or composite. At the higher temperatures (260 C and above), the surface loss predominates. Below 260 C, the surface loss and the bulk core loss become more equivalent. Between 175 and 260 C, the initial weight change is due to a weight gain mechanism with a visible lifetime that diminishes as the aging temperature increases.

Bowles, Kenneth J.↗

Resolving the Heat Generated from ZrO 2 Atomic Layer Deposition Surface Reactions

Abstract In situ pyroelectric calorimetry and spectroscopic ellipsometry were used to investigate surface reactions in atomic layer deposition (ALD) of zirconium oxide (ZrO 2 ). Calibrated and time‐resolved in situ ALD calorimetry provides new insights into the thermodynamics and kinetics of saturating surface reactions for tetrakis(dimethylamino)zirconium(IV) (TDMAZr) and water. The net ALD reaction heat ranged from 0.197 mJ cm −2 at 76 °C to 0.155 mJ cm −2 at 158 °C, corresponding to an average of 4.0 eV/Zr at all temperatures. A temperature dependence for reaction kinetics was not resolved over the range investigated. The temperature dependence of net reaction heat and distribution among metalorganic and oxygen source exposure is attributed to factors including growth rate, equilibrium surface hydroxylation, and the extent of the reaction. ZrO 2 ‐forming surface reactions were investigated computationally using DFT methods to better understand the influence of surface hydration on reaction thermodynamics.

Bielinski, Ashley R.↗

The effect of surface oxide layer on the rate of hydrogen emission from aluminum and its alloys in a high vacuum

The influence of surface oxide layers on the kinetics of hydrogen emission at the high vacuum of 10 to the minus 8th power torr was investigated at temperatures from 20 to 450 C using samples of pure AB00 aluminum and the cast alloy AMg. Cast and deformed samples of AMts alloy were used to study the effect of oxide film thickness on the rate of hydrogen emission. Thermodynamic calculations of the reactions of the generation and dissociation of aluminum oxide show that degasification at elevated temperatures (up to 600 C) and high vacuum will not reduce the thickness of artificially-generated surface oxide layers on aluminum and its alloys.

Makarova, V. I.↗

Pulsational analyses of post planetary nebula central stars and degenerate dwarfs

Recent observational and theoretical studies of the ZZ Ceti variabls (DA degenerate dwarfs), the DBV variables (DB degenerate dwarfs), and the GW Vir variables (D0 degenerate dwarfs) have shown them to be pulsating in nonradial g-modes. The pulsation mechanism has been identified for each class of variable star. For the ZZ Ceti and DBV variables it is both the kappa and gamma effects in the partial-ionization regions of either H or He and also a a recently identified pulsation-driving mechanism called 'convection blocking'. For the GW Vir variables, it is the kappa and gamma effects in the partial-ionization region of C and O. The ZZ Ceti variables must have pure H surface layers, the DBV stars must have pure He surface layers, and the GW Vir stars must have C- and O-rich surface layers with only a small amount of He present. The accuracy of the prediction for the GW Vir stars is limited by the lack of observational determinations of their luminosity, effective temperature, and composition.

Starrfield, Sumner↗

Ultrastructure of Organohalide-Respiring Dehalococcoidia Revealed by Cryo-Electron Tomography

Dehalococcoides mccartyi (Dhc) and Dehalogenimonas spp. (Dhgm) are members of the class Dehalococcoidia, phylum Chloroflexi, characterized by streamlined genomes and a strict requirement for organohalogens as electron acceptors. Here, we used cryo-electron tomography to reveal morphological and ultrastructural features of Dhc strain BAV1 and “Candidatus Dehalogenimonas etheniformans” strain GP cells at unprecedented resolution. Dhc cells were irregularly shaped discs (890 ± 110 nm long, 630 ± 110 nm wide, and 130 ± 15 nm thick) with curved and straight sides that intersected at acute angles, whereas Dhgm cells appeared as slightly flattened cocci (760 ± 85 nm). The cell envelopes were composed of a cytoplasmic membrane (CM), a paracrystalline surface layer (S-layer) with hexagonal symmetry and ~22-nm spacing between repeating units, and a layer of unknown composition separating the CM and the S-layer. Cell surface appendages were only detected in Dhc cells, whereas both cell types had bundled cytoskeletal filaments. Repetitive globular structures, ~5 nm in diameter and ~9 nm apart, were observed associated with the outer leaflet of the CM. We hypothesized that those represent organohalide respiration (OHR) complexes and estimated ~30,000 copies per cell. In Dhgm cultures, extracellular lipid vesicles (20 to 110 nm in diameter) decorated with putative OHR complexes but lacking an S-layer were observed. Furthermore, the new findings expand our understanding of the unique cellular ultrastructure and biology of organohalide-respiring Dehalococcoidia.

59 BASIC BIOLOGICAL SCIENCES↗

The 'soil' of Mars /Viking 1/

The immediate environs of the Viking 1 lander are described, and the techniques employed to deduce the properties of the two different 'soil' types there are summarized. It is shown that the surface in the immediate vicinity of the lander consists of an area with fine-grained materials ('Sandy Flats') and a rocky area set in a matrix of finer-grained material ('Rocky Flats'). Estimates are given for the bulk density, particle density, particle size distribution, cohesion, angle of internal friction, and penetration resistance of the surface layer in each area. Footpad penetration into the surface layer is discussed, and wind removal of particles is examined. It is concluded that the surface layer of the Viking 1 landing site contains loess, dune sand, lunar nominal soil, lag gravel, and bare rock.

Shorthill, R. W.↗

Structure disorder degree of polysilicon thin films grown by different processing: Constant C from Raman spectroscopy

Flat, low-stress, boron-doped polysilicon thin films were prepared on single crystalline silicon substrates by low pressure chemical vapor deposition. It was found that the polysilicon films with different deposition processing have different microstructure properties. The confinement effect, tensile stresses, defects, and the Fano effect all have a great influence on the line shape of Raman scattering peak. But the effect results are different. The microstructure and the surface layer are two important mechanisms dominating the internal stress in three types of polysilicon thin films. For low-stress polysilicon thin film, the tensile stresses are mainly due to the change of microstructure after thermal annealing. But the tensile stresses in flat polysilicon thin film are induced by the silicon carbide layer at surface. After the thin film doped with boron atoms, the phenomenon of the tensile stresses increasing can be explained by the change of microstructure and the increase in the content of silicon carbide. We also investigated the disorder degree states for three polysilicon thin films by analyzing a constant C. It was found that the disorder degree of low-stress polysilicon thin film larger than that of flat and boron-doped polysilicon thin films due to the phase transformation after annealing. After the flat polysilicon thin film doped with boron atoms, there is no obvious change in the disorder degree and the disorder degree in some regions even decreases.

36 MATERIALS SCIENCE↗

CO2 CH4 flux Air temperature Soil temperature and Soil moisture, Utqiagvik (Barrow), Alaska 2013 ver. 1

This dataset consists of field measurements of CO2 and CH4 flux, as well as soil properties made during 2013 in Areas A-D of Intensive Site 1 at the Next-Generation Ecosystem Experiments (NGEE) Arctic site near Barrow, Alaska. Included are i) measurements of CO2 and CH4 flux made from June to September (ii) Calculation of corresponding Gross Primary Productivity (GPP) and CH4 exchange (transparent minus opaque) between atmosphere and the ecosystem (ii) Measurements of Los Gatos Research (LGR) chamber air temperature made from June to September (ii) measurements of surface layer depth, type of surface layer, soil temperature and soil moisture from June to September. This data package contains two *.csv files and one *.pdf file. NGEE Arctic Project Summary: The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

A critical study of the role of the surface oxide layer in titanium bonding

The molecular understanding of the role which the surface oxide layer of the adherend plays in titanium bonding is studied. The effects of Ti6-4 adherends pretreatment, bonding conditions, and thermal aging of the lap shear specimens were studied. The use of the SEM/EDAX and ESCA techniques to study surface morphology and surface composition was emphasized. In addition, contact angles and both infrared and visible reflection spectroscopy were used in ancillary studies.

Dias, S.↗

Compositional depth profile of a native oxide LPCVD MNOS structure using X-ray photoelectron spectroscopy and chemical etching

It is pointed out that there is no report of an unambiguous analysis of the composition and interfacial structure of MNOS (metal-nitride oxide semiconductor) systems, despite the technological importance of these systems. The present investigation is concerned with a study of an MNOS structure on the basis of a technique involving the use of X-ray photoelectron spectroscopy (XPS) with a controlled stopped-flow chemical-etching procedure. XPS is sensitive to the structure of surface layers, while stopped-flow etching permits the controlled removal of overlying material on a scale of atomic layers, to expose new surface layers as a function of thickness. Therefore, with careful analysis of observed intensities at measured depths, this combination of techniques provides depth resolution between 5 and 10 A. According to the obtained data there is intact SiO2 at the substrate interface. There appears to be a thin layer containing excess bonds to silicon on top of the SiO2.

Wurzbach, J. A.↗

Pluto's atmosphere - Models based on refraction, inversion, and vapor-pressure equilibrium

Viking spacecraft radio-occultation measurements indicate that, irrespective of substantial differences, the polar ice cap regions on Mars have inversions similar to those of Pluto, and may also share vapor pressure equilibrium characteristics at the surface. This temperature-inversion phenomenon occurs in a near-surface boundary layer; surface pressure-temperature may correspond to the vapor-pressure equilibrium with CH4 ice, or the temperature may be slightly higher to match the value derived from IRAS data.

Eshleman, Von R.↗