Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface slopes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Full-Scale Drop Test of a Fokker F28 Wingbox Fuselage Section

During the summer of 2017, a vertical drop test was conducted on a partial section of a Fokker F28 MK4000 aircraft as a part of a joint NASA/FAA effort to investigate the performance of transport category aircraft under realistic crash conditions. Ten Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) ranging from 5th to 95th percentile sizes were used for the collection and comparison of occupant loads. Additionally, overhead bin mass simulators were added to achieve a realistic fuselage configuration. The section was dropped with a downward facing pitch angle onto a sloping soil surface in order to simulate a local horizontal velocity in the airframe. Instrumentation consisting of accelerometers was installed to measure floor, seat track, ATD, and overhead bin acceleration responses. Self-contained data recorders logging accelerations and rotational rates were also used on the seat tracks and lower structure as evaluations for crash recording devices in potential future use cases. The right side of the section was painted with a stochastic black and white speckle pattern for use in full field photogrammetric imaging techniques. Results collected from the airframe accelerometers will be presented, and deformation and failures of the test article structure will be discussed. Finally, an examination of the test article motion will be presented using derived components of local velocities with their effect on the impact acceleration and airframe response.

Littell, J. D.↗
NASA NTRSDate not supplied

Relating Land Cover Change to Runoff Distribution Using NASA Earth Observations in Riley County, Kansas

In recent years, Riley County, Kansas experienced high levels of flooding potentially due to changes in land use and impervious surface. To analyze the increase in floods and runoff patterns over time, this study contrasted two methods of curve number (CN) calculation, which estimated runoff from rainfall events, from 2006-2020. The conventional calculation method used a look-up table and tracked land use/land cover change. This method resulted in static tables from various inputs such as soil type, surface imperviousness, slope, and crop phenology to estimate runoff versus infiltration. These tables allowed for phenology specific curve numbers and accounted for various farming techniques but required many inputs and lacked flexibility to include seasonal variations in vegetation. In contrast, the dynamic method is a more modern and simple calculation employing normalized difference vegetation index (NDVI) data from Landsat 5, Landsat 7, and Landsat 8 satellites compiled over the rainy season each year to calculate curve numbers based off seasonal vegetation. This dynamic method allowed for more precise analysis of runoff variability because NDVI is a more accurate, real-time measurement for land cover and it could be calculated with greater temporal detail. The results will allow decision makers to make more informed decisions on resiliency strategies to address future flooding.

Trista Brophy↗
DOE OSTI2020

Multiscale Framework Simulates Utility-Scale Wind Plant in Its Natural Environment. First-ever simulation could lead to a vital understanding of wind plant performance

Wind plant performance depends on local environmental conditions—and understanding those conditions is crucial to research on wind plant dynamics. Factors such as sloping terrain, surface type and cover, atmospheric heating and cooling, and weather events all play a role in determining the winds that turbines convert into power. However, most models used for wind plant design and operation do not sufficiently account for environmental effects. This can limit our understanding of wind plant dynamics and, thus, our ability to design, site, and operate wind plants for maximum power production and reliability. To meet this challenge, Arthur and other LLNL researchers partnered with scientists at the National Center for Atmospheric Research; the University of California, Berkeley; the University of Colorado, Boulder; and Texas Tech University to develop and demonstrate a novel, mesoscale-tomicroscale wind plant modeling framework.

17 WIND ENERGY↗
DOE OSTI2023

Collimated phase measuring deflectometry

Phase measuring deflectometry has been applied for free-form specular surface metrology, but its measured slope results are sensitive to the depth of sample positioning, which is also called the height-slope ambiguity. The objective of this work is to tackle this height-slope ambiguity problem. The main idea is to introduce collimated camera rays using a telecentric imaging lens and collimated structured-light illumination with a Fourier lens. This setup makes the fringe phases become only sensitive to the surface slopes and insensitive to the depth of the sample positioning. In this way, the slope calculation is theoretically independent of the sample depth. We call this new deflectometry technique Collimated Phase Measuring Deflectometry (CPMD). With our developed CPMD experimental setup, the measurement is insensitive to the depth of sample positioning, e.g., the measured height dispersion is less than 30 nm RMS within a 10 mm depth range when measuring a 50-mm-diameter spherical mirror with a 200 mm radius of curvature. In conclusion, the merits and limitations of the proposed CPMD technique are discussed, revealing its prospects in practical metrology applications and potential future investigations.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Harmonized Sentinel-1 SAR Global River Geometry and Inundation Database

Satellite-based observations on river geometries are sporadic in time, space, or both. Most satellite-based surface water maps, river widths, water surface elevations (WSE), slopes, and bathymetry are asynchronized in time and space. The current configuration of satellites such as Sentinel-6 measured the WSE but is missing the river width, slopes, and depths. To advance hydrological sciences research, there is a need to produce a harmonized time series of river geometry data of non-SWOT satellites in partnership with the upcoming SWOT mission. The SWOT satellite will measure river width, height, and slope but missing river depth measurements in space and time. Further, none of these current satellites measure the WSE, river width, and slopes synchronously. In this work, we use the Sentinel-1 SAR satellite data archive from 2015 to the present to create a global river width and surface water database at the reach scale. A modified version of the Sentinel SAR surface water classification algorithm from ASF is used to quantify the surface water extent on the stream approximately every six days (at the equator) at 10m spatial resolution globally. This 10m water mask is fed into a workflow to quantify the river widths, surface water inundations, slopes, and synthetic bathymetry in SWORD (SWOT River Database) stream networks. A Satellite HAND is used to address the cloud obscured surface water observations using a trained machine learning algorithm. We use WSE derived from the Global Water Monitor from NASA GSFC, Hydroweb from LEGOS, and ICESat-2 to harmonize the WSE observation. And Landsat-8/9 and Sentinel-2 water observations to fill the gaps in the Sentinel-1 SAR database. We use Congo River Basin as a test case where we have more than 500 radar altimetry-based WSE, continuous series of Sentinel-1, ICESat-2, Landsat-8/9, and Sentinel-2 observations. A Congo River hydrologic model is used to generate the streamflow discharge. The satellite observed river reaches are assimilated with the stream flows computed by the routing models. And the downstream reaches in the river network without satellite observations get optimized for discharge/river geometry at each observation cycle. Our final product is a harmonized river geometry dataset (reach's water extent, WSE, slope, synthetic bathymetry) for Congo Basin's SWORD reaches.

Chandana Gangodagamage↗
NASA NTRS1992

Natural-Flow Wing

Novel scheme developed to contour three-dimensional upper and lower surfaces of wing independently to take maximum advantage of naturally occurring flow and resultant distribution of pressure over broad mach number and lift range. Scheme contours lower and upper surfaces at given cross section to optimize local slopes of upper surface. Sections sheared vertically to create reflexed lower surface. Creates wing nearly flat with mild cumber and minimal twist. Results in design efficient over wide range of lift conditions. Wings for supersonic flight able to provide improved performance at lower speeds without resorting to heavy, complex, and expensive variable-camber devices. Ramifications for both transportation and military systems.

Wood, Richard M.↗
NASA NTRS1987

Effect of dropped plies on the strength of graphite-epoxy laminates

The reduction in the compressive and tensile strengths of graphite-epoxy laminates with thickness discontinuities due to dropped plies was studied by experiment and analysis. The specimens were fabricated with all the dropped plies lumped together in the center of a sixteen-ply quasi-isotropic layup, such that one surface was flat and the slope of the opposite surface changed abruptly at the dropped ply location to accommodate the thickness change. Even though the thick and thin sections are symmetrically laminated, there exists bending-extension coupling due to the geometric eccentricity of the middle planes of the thick and thin sections. Experiments were conducted on fifty-four specimens that differed in the configuration of the dropped plies only. The strength of a laminate with dropped plies is less than the strength of its thin section, and the compressive strength of a laminate with dropped plies is less than its tensile strength. The reduction in strength is directly related to the axial stiffness change between the thick and thin sections. To examine the mechanism of failure, the three-dimensional state of stress in the dropped ply region was evaluated by the finite element method. A tensile interlaminar criterion predicted the correct location of failure, but underestimated the failure load.

Curry, James M.↗
DOE OSTI2020

Two-dimensional simulations of internal gravity waves in the radiation zones of intermediate-mass stars

Intermediate-mass main-sequence stars have large radiative envelopes overlying convective cores. This configuration allows internal gravity waves (IGWs) generated at the convective–radiative interface to propagate towards the stellar surface. The signatures of these waves can be observed in the photometric and spectroscopic data from stars. Here, we have studied the propagation of these IGWs using two-dimensional (2D) fully non-linear hydrodynamical simulations with realistic stellar reference states from the 1D stellar evolution code, Modules for Stellar Astrophysics (MESA). When a single wave is forced, we observe wave self-interaction. When two waves are forced, we observe non-linear interaction (i.e. triadic interaction) between these waves forming waves at different wavelengths and frequencies. When a spectrum of waves similar to that found in numerical simulations is forced, we find that the surface IGW frequency slope is consistent with recent observations. This power law is similar to that predicted by linear theory for the wave propagation, with small deviations that can be an effect of non-linearities. When the same generation spectrum is applied to 3 M ⊙ models at different stellar rotation and ages, the surface IGW spectrum slope is very similar to the generation spectrum slope.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2008

A Capable and Temporary Test Facility on a Shoestring Budget: The MSL Touchdown Test Facility

The Mars Science Laboratory mission (MSL) has undertaken a developmental Touchdown Test Program that utilizes a full-scale rover vehicle and an overhead winch system to replicate the skycrane landing event. Landing surfaces consisting of flat and sloped granular media, planar, rigid surfaces, and various combinations of rocks and slopes were studied. Information gathered from these tests was vital for validating the rover analytical model, validating certain design or system behavior assumptions, and for exploring events and phenomenon that are either very difficult or too costly to model in a credible way. This paper describes this test program, with a focus on the creation of test facility, daily test operations, and some of the challenges faced and lessons learned along the way.

rover↗
DOE OSTI2020

Improvement of Atmospheric Objective Analysis Over Sloping Terrain and Its Impact on Shallow-Cumulus Clouds in Large-Eddy Simulations

Surface topography strongly impacts the regional atmospheric circulation dynamically and thermodynamically. Over the Great Plains in the United States, the gently tilted slope is an important factor that impacts clouds, convection and regional circulations. This study enhances an atmospheric constrained variational analysis by using a terrain-following sigma vertical coordinate and applies to the data collected at the Southern Great Plain (SGP) site of the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) program. Sensitivity studies are performed to examine the impact of the terrain effects on the derived large-scale atmospheric forcing fields and the simulated shallow-cumulus clouds in large-eddy simulation (LES) driven by the forcing. We found that the terrain impacts on the large-scale forcing fields are mainly at lower levels and are strongly controlled by up/downslope winds. The response of the derived forcing to the slope of the terrain is monotonic, but the response of the simulated shallow-cumulus clouds is more complex and depends on several factors. Overall, the terrain impact is small over SGP due to the small slope angle. However, the flat-surface assumption may cause larger biases in the large-scale forcing fields at locations with steeper terrain. The new sigma-coordinate algorithm, with its consideration of surface slope, should be more suitable to derive large-scale objective analysis over regions with steep terrain for application to force single-column models, cloud resolving models and LES models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Effect of grain dissolution on sloping ground

The static and dynamic stability of natural or constructed slopes can be affected by dissolution or dissolution-like phenomena. Their underlying mechanisms, however, remain unclear. New experimental results and discrete element simulations provide particle-level and macroscale information on the consequences of mineral dissolution on slope behavior. At the microscale, load-carrying grain arches develop around dissolving particles, the porosity increases, and contact force chains evolve to form a honeycomb topology. At the macroscale, while vertical settlements are the prevailing deformation pattern, lateral granular movements that create mass wasting are prominent in sloping ground, even under the quasi-static granular loss. Horizontal grain displacement is maximum at the surface and decreases linearly with the distance from the slope surface to become zero at the bottom boundaries, much like vertical granular displacement along the depth. Sediments with smaller friction angles and steeper slopes experience greater displacement, both vertically and horizontally. Slopes become flatter after dissolution, with the reduction in slope angle directly related to the loss in ground elevation, ΔH/H o . Yet, because of the porous fabric that results from dissolution, vertical shortening is less than the upper bound, estimated from the loss in the solid mass fraction, ΔH/H o ≈SF. Under water-saturated conditions, the post-dissolution fabric may lead to sudden undrained shear and slope slide.

42 ENGINEERING↗
NASA NTRS1987

The design of blended rolled edges for compact range main reflectors

In a compact range (which employs a parabolic main reflector to convert the spherical wave originating from a point source to a reflected plane wave) the edge-generated diffractive fields degrade the uniformity of the plane wave. To reduce the energy diffracted from the edge surfaces, terminations can be added to the parabola, such that the slope of the surface is continuous at the junctions. This paper discusses the problem of designing an optimized rolled edge. Two examples of reflectors with rolled edges are presented, one with elliptic rolled edges and the other with blended rolled edges, both adhering to the same constraints on minimum operating frequency and size. It was found that the reflector with the cosine-squared blended rolled edges has a much larger usable target zone than the one with the elliptic rolled edges.

Pistorius, C. W. I.↗
NASA NTRS1983

A comparison between backscattering coefficients using Gaussian and non-Gaussian surface statistics

Backscattering coefficients computed using Gaussian and non-Gaussian surface statistics are compared. The computations are performed for a class of surface-height distributions and surface correlation functions. Results indicate that the coherent component of the scattering coefficient is strongly dependent upon the surface-height distribution. The noncoherent component also depends on the surface-height distribution and the surface root-mean-square (rms) slope when the rms surface height is large relative to the incident wavelength. On the other hand, when the surface rms height is moderate or small, the noncoherent component is sensitive mainly to the surface-height correlation function.

Eom, H. J.↗
NASA NTRS1994

Continuous hierarchical slope-aspect color display for parametric surfaces

A method for generating an image of a parametric surface, such as the aspect of terrain which maximizes color contrast to permit easy discrimination of the magnitude, ranges, intervals or classes of a surface parameter while making it easy for the user to visualize the form of the surface, such as a landscape. The four pole colors of the opponent process color theory are utilized to represent intervals or classes at 90 degree angles. The color perceived as having maximum measured luminance is selected to portray the color having an azimuth of an assumed light source and the color showing minimum measured luminance portrays the diametrically opposite azimuth. The 90 degree intermediate azimuths are portrayed by unique colors of intermediate measured luminance, such as red and green. Colors between these four pole colors are used which are perceived as mixtures or combinations of their bounding colors and are arranged progressively between their bounding colors to have perceived proportional mixtures of the bounding colors which are proportional to the interval's angular distance from its bounding colors.

Moellering, Harold J.↗
NASA NTRS1985

A New Technique for System-to-system Transfer of Surface Data

The purpose is to describe a recently developed technique aimed at providing a universal interface between surface types. In brief, a software package was developed which functions a common denominator of CAD/CAM surface types. This software enable one to convert from any given surface representation to any other target representation. The tiles maintain the same slope continuity as the target surface gram, bicubic patches are used since they allow one to match point, slope, and twist vectors to the target surface. Thus, slopes can be continuous or discontinuous as they are on the target surface. The patches can be of lower order if desired. For example, if only point information is available, the patches produced will be bilinear; however, the number of patches required is likely to increase correspondingly. The patches can be of higher order although many systems will not accept patches of more than order four. The final result of the program is a rectangular grid of bicubic patches. The patches fit the target surface exactly at their corners. Also, the patch corners have the same tangent and twist vectors. Adjacent patches will have slope continuity, unless a discontinuity was indicated by the target surface.

Sterling, M. W.↗
NASA NTRS1978

The effect of wind on the microwave emission from the ocean's surface at 37 GHz

The microwave brightness temperature measurements from the Electrically Scanned Microwave Radiometer (frequency = 37 GHz) are compared with oceanic wind measurements from data buoys. It is shown that the brightness temperature can be manipulated to yield a measure of the surface roughening which can be very well accounted for by a simple geometric optics model. The data of 1.4, 8.36 and 19.34 GHz were similarly manipulated and shown to require a surface with less slope variance than predicted by optical measurements. It is also shown that the surface may be treated as isotropic to an accuracy equivalent to the roughening produced by a 2 m/s wind speed increment.

Wilheit, T. T.↗
NASA NTRS1977

Topography of sinuous rilles in the Harbinger Mountains region of the moon

Five sinuous rilles in mare basalts in the Harbinger Mountains region of the moon are described. Rille length ranges from 12 to 79 km, width from 0.8 to 4.8 km, and depth from 100 to 300 m. The rilles appear to become shallower to the north, while the southern ends are characterized by circular-to-elongate depressions that occur on a 30-km-in-diameter dome of probable volcanic origin. Longitudinal profiles show that the rille floors have a northward slope of less than one deg, consistent with the general slope of the surrounding mare surface. Structural studies indicate that slope, rather than the regional structural pattern, is the dominant factor controlling rill direction. Topographic data support the theory that the rilles were formed as lave channels or tubes.

Strain, P. L.↗
NASA NTRS1999

Method and apparatus for controlling an earthworking implement to preserve a crown on a road surface

A method and apparatus for controlling an earthworking implement on an earthworking machine to preserve a crown on the surface of a road, including determining the position of the crown on the road surface, choosing a sloped grade on one side of the crown, positioning the earthworking implement on the sloped grade so that a first end of the earthworking implement is on the road surface. The processor determines a desired position of a second end of the earthworking implement so that the second end overlaps the crown and the earthworking implement does not cut the crown.

Staub, Michael D.↗