Search NASA⌕ Search

SEARCH · Search NASA

Results for “sweep testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Low thermal inertia thermal barrier coatings for spark ignition engines: An experimental study

Application of thermal barrier coatings in spark ignition engines have historically been avoided due to the knock penalty associated with higher surface temperatures induced by the ceramic layer. However, advances in low thermal inertia coatings (i.e. temperature swing coatings) that combine low thermal conductivity with low volumetric heat capacity can prevent excessively high surface temperatures during the intake stroke and reduce or avoid knock while improving performance and efficiency. In this study, a novel coating material was tested in a low compression ratio spark ignition engine to evaluate the performance of an advanced low thermal inertia coating during steady and cold-start conditions. A total of four pistons with this novel material was tested, with an additional piston coated with gadolinium zirconate. Spark timing sweeps demonstrated a maximum 0.8% relative thermal efficiency gain with a thin coating of the novel material. Here, the novel material coated above 200-microns showed a deterioration in performance and efficiency due to charge heating increasing knock propensity. Cold-start tests demonstrated that charge heating is beneficial for reducing unburned hydrocarbons and particle matter emissions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick GlauertGoldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick Glauert Goldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗

Wind tunnel tests of an F-8 airplane model equipped with an oblique wing

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to study the lift, drag and stability characteristics of a 0.087-scale model of an operational airplane fitted with an oblique wing. The model wing was of elliptical planform with an unswept aspect ratio of 12.7 and a thickness of 10 percent. All other external geometric features of the model were scaled to the basic full size operational airplane with the engine inlet faired closed. Longitudinal and lateral-directional stability data were obtained with the wing at sweep angles of 0 deg, 45 deg and 60 deg Test Mach numbers ranged from 0.6 to 1.4 deg Angles of attack were between minus 4 deg and 8 deg at zero sideslip. Angles of sideslip were between plus and minus 4 degrees for two angles of attack depending upon the wing configuration. Tests were conducted at a Reynolds number of 6 million per foot except for a few runs when balance capacity limited the Reynolds number to 4 million per foot.

Graham, L. A.↗

Results of buffet tests in a cryogenic wind tunnel

Buffet tests on two semispan wing models with different leading edge sweep show that it is feasibile to use the standard dynamic wing root bending moment technique in a cryogenic wind tunnel. One model was a slender 65 deg swept delta wing with sharp leading edges. The other model was an unswept wing of aspect ratio 1.5 with a British NPL 9510 airfoil section. The results for the 65 deg swept delta wing indicate the importance of matching the reduced frequency parameter in model tests for planforms which are sensitive to reduced frequency parameter if quantitative buffet measurements are required. The unique ability of a pressurized cryogenic wind tunnel to separate the effects of Reynolds number and of static aeroelastic distortion by variations in the tunnel stagnation temperature and pressure were demonstrated.

Boyden, R. P.↗

Survey of wing and flap lower-surface temperatures and pressures during full-scale ground tests of an externally blown flap system

Full-scale ground tests of an externally blown flap system were made using the wing of an F-111B airplane and a CF700 engine. Pressure and temperature distributions were determined on the undersurface of the wing, vane, and flap for two engine exhaust nozzles (conical and daisy) at several engine power and engine/wing positions. The tests were made with no airflow over the wing. The leading-edge wing sweep angle was fixed at 26 deg, the angle of incidence between the engine and the wing was fixed at 3 deg, and the tests were conducted with the flap retracted, extended and deflected 35 deg, and extended and deflected 60 deg. The integrated local pressures on the undersurface of the flap produced loads approximately three times as great at the 60 deg flap position as at the 35 deg flap position. With both nozzle configurations, more than 90 percent of the integrated pressure loads were contained within plus or minus 20 percent of the flap span centered around the engine exhaust centerline. The maximum temperature recorded on the flaps was 218 C (424 F) for the conical nozzle and 180 C (356 F) for the daisy nozzle.

Hughes, D. L.↗

Development of electromagnetic acoustic transducer (EMAT) phased arrays for SFR inspection

A long-standing problem for Sodium cooled Fast Reactor (SFR) instrumentation is the development of efficient under-sodium visualization systems adapted to the hot and opaque sodium environment. Electromagnetic Acoustic Transducers (EMAT) are potential candidates for a new generation of Ultrasonic Testing (UT) probes well-suited for SFR inspection that can overcome drawbacks of classical piezoelectric probes in sodium environment. Based on the use of new CIVA simulation tools, we have designed and optimized an advanced EMAT probe for under-sodium visualization. This has led to the development of a fully functional L-wave EMAT sensing system composed of 8 elements and a casing withstanding 200° C sodium inspection. Laboratory experiments demonstrated the probe's ability to sweep an ultrasonic beam to an angle of 15 degrees. Testing in a specialized sodium facility has shown that it was possible to obtain pulse-echo signals from a target under several different angles from a fixed position.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Vibration testing of the JE-M-604-4-IUE rocket motor (Thiokol P/N E 28639-03)

The NASA International Ultraviolet Explorer (IUE) rocket motor (TE-M-604-4), a solid fuel, spherical rocket motor, was vibration tested in the Impact, Vibration, and Acceleration (IVA) Test Unit of the von Karman Gas Dynamics Facility (VKF). The objective of the test program was to subject the motor to qualification levels of sinusoidal and random vibration prior to the altitude firing of the motor in the Propulsion Development Test Cell (T-3), Engine Test Facility (ETF), AEDC. The vibration testing consisted of a low level sine survey from 5 to 2,000 Hz, followed by a qualification level sine sweep and qualification level random vibration. A second low level sine survey followed the qualification level testing. This sequence of testing was accomplished in each of three orthogonal axes. No motor problems were observed due to the imposition of these dynamic environments.

Alt, R. E.↗

Reformulating a Gurson-based dynamic damage model and demonstrating improved predictive power and numerical robustness

The original Tepla (TEnsile PLAsticity) ductile damage model, based on the Gurson yield surface, has long been used to model damage evolution and material failure under dynamic loading. Unfortunately, Tepla suffered from mesh sensitivity, numerical instability, and limited predictive capability. Here, we theoretically reformulate Tepla to address these issues. We especially focus on the prediction of porosity, which is the key state variable used for modeling ductile damage, as compared to more easily measured surface velocities, which are at best an indirect measure of damage. Key model changes include separating the viscosity during volumetric void growth from underlying shear strength behavior and switching to an iterative bisection solver. The new Tepla is then calibrated on incipient spall experiments on half-hard copper and tantalum, which demonstrate its ability to simultaneously fit the model to recovered porosity distributions and measured surface velocities, a stringent test. Improved numerical behavior, such as greatly reduced mesh sensitivity, is also shown in those simulations. Finally, the new Tepla model is applied to several high-explosive loaded, sweeping wave experiments, showing the ability of the model to predict behavior on tests with significantly different loading conditions and histories than the calibration data.

36 MATERIALS SCIENCE↗

Applying the Scientific Method of Cybersecurity Research

The cyber environment has rapidly evolved from a curiosity to an essential component of the contemporary world. As the cyber environment has expanded and become more complex, so have the nature of adversaries and styles of attacks. Today, cyber incidents are an expected part of life. As a result, cybersecurity research emerged to address adversarial attacks interfering with or preventing normal cyber activities. Historical response to cybersecurity attacks is heavily skewed to tactical responses with an emphasis on rapid recovery. While threat mitigation is important and can be time critical, a knowledge gap exists with respect to developing the science of cybersecurity. Such a science will enable the development and testing of theories that lead to understanding the broad sweep of cyber threats and the ability to assess trade-offs in sustaining network missions while mitigating attacks. The Asymmetric Resilient Cybersecurity Initiative at Pacific Northwest National Laboratory is a multi-year, multi-million dollar investment to develop approaches for shifting the advantage to the defender and sustaining the operability of systems under attack. The initiative established a Science Council to focus attention on the research process for cybersecurity. The Council shares science practices, critiques research plans, and aids in documenting and reporting reproducible research results. The Council members represent ecology, economics, statistics, physics, computational chemistry, microbiology and genetics, and geochemistry. This paper reports the initial work of the Science Council to implement the scientific method in cybersecurity research. The second section describes the scientific method. The third section in this paper discusses scientific practices for cybersecurity research. Section four describes initial impacts of applying the science practices to cybersecurity research.

Tardiff, Mark F.↗

Measured and calculated inplane stability characteristics for an advanced bearingless main rotor

A program of experimental and analytical research has been performed to demonstrate the effects of rotor and fuselage design parameters on rotor in-plane stability, including aeromechanical stability. The experimental data were obtained from hover and wind-tunnel tests of a scaled advanced bearingless main rotor model. Both isolated-rotor and free-hub conditions were tested. Test parameters included blade built-in cone and sweep angles; rotor inplane structural stiffness and damping; pitch link stiffness and location; and fuselage natural frequency, damping, and inertia. The results show that rotor blade structural damping is one of the most influential design parameters in obtaining acceptable aeromechanical stability margins. Other parameters, such as blade cone angle, pitch link location (rotor delta 3) and anisotropic hub damper configurations, may be used to improve stability margins, but their individual effects are subtle.

Weller, W. H.↗

Vortex flow hysteresis

An experimental study was conducted to quantify the hysteresis associated with various vortex flow transition points and to determine the effect of planform geometry. The transition points observed consisted of the appearance (or disappearance) of trailing edge vortex burst and the transition to (or from) flat plate or totally separated flows. Flow visualization with smoke injected into the vortices was used to identify the transitions on a series of semi-span models tested in a low speed tunnel. The planforms tested included simple deltas (55 deg to 80 deg sweep), cranked wings with varying tip panel sweep and dihedral, and a straked wing. High speed movies at 1000 frames per second were made of the vortex flow visualization in order to better understand the dynamics of vortex flow, burst and transition.

Cunningham, A. M., Jr.↗

Pressure distributions and oil-flow patterns for a swept circulation-control wing

Pressure distributions and photographs of oil flow patterns are presented for a circulation control wing. The model was an aspect ratio four semispan wing mounted on the side wall of the NASA Ames Transonic Wind Tunnel. The airfoil was a 20 percent thick ellipse, modified with circular leading and trailing edges of 4 percent radius, and had a 25.4 cm constant chord. This configuration does not represent a specific wing design, but is generic. A full span, tangetial, rearward blowing, circulation control slot was incorporated ahead of the trailing edge on the upper surface. The wing was tested at Mach numbers from 0.3 to 0.75 at sweep angle of 0 to 45 deg with internal to external pressure ratios of 1.0 to 3.0. Lift and pitching momemt coefficients were obtained from measured pressure distributions at five span stations. When the conventional corrections resulting from sweep angle are applied to the lift and moment of circulation control sections, no additional corrections are necessary to account for changes in blowing efficiency. This is demonstrated for an aft sweep angle of 45 deg. An empirical technique for estimating the downwash distribution of a swept wing was validated.

Keener, Earl R.↗

Enhanced heavy oil recovery by low salinity polymer flood combined with microgel treatment

“Heavy oil resources account for a large portion of the total oil reserves around the world. The target heavy oil reservoir is located on Alaska’s North Slope (ANS). Advantages of low-salinity HPAM polymer (LSP) over high-salinity polymer (HSP) were demonstrated. LSP could recover more oil with 40% less polymer consumption. No additional oil was recovered by HSP after LSP flood. The first-ever polymer flood pilot on ANS showed remarkable success regarding water cut reduction, oil production increase, delayed breakthrough, and projected oil recovery improvement. Polymer alone was insufficient to achieve satisfactory recovery as the reservoirs were highly heterogeneous. Microgels could improve the effectiveness of polymer flood by reducing water cut and increasing oil recovery. Favorable working conditions were identified. Microgel transport behavior was studied using superpermeable sandpacks (27-221 darcies) with multiple pressure sensors. The particle-to-pore matching size ratio significantly impacted the effectiveness of the gels. A threshold differential pressure (ΔPth) and critical pressure gradient (∇Pcr) were required to push the gels to penetrate and propagate through the channels. The ΔPth and ∇Pcr revealed the underlying mechanisms of selective penetration/placement behavior of microgels in heterogeneous reservoirs. Diagrams were developed to estimate the maximum propagation distance of the gels in channels in conceptual field applications. Sandwich-like channel models and methodologies were developed to comprehensively evaluate the effectiveness of gel materials. Gel retention in the channels was quantified. Results also indicated that the retained gels were dehydrated. Fluid diversion and sweep improvement after gel treatments were evaluated by tracer tests”--Abstract, page iv.

Zhao, Yang↗

Reynolds number effects on the aerodynamic characteristics of irregular planform wings at Mach number 0.3

The subsonic aerodynamic characteristics of a series of irregular planform wings were studied in wind tunnel tests conducted at M = 0.3 over a range of Reynolds numbers from 1.6 million to 26 million/m. The five basic wing planforms varied from a trapezoidal to a delta shape. Leading edge extensions, added to the basic shape, varied in approximately 5 deg increments from the wing leading edge sweep-back angle to a maximum 80 deg. Most of the tests were conducted using an NACA 0008 airfoil section with grit boundary layer trips. Tests were also conducted using an NACA 0012 airfoil section and an 8% thick wedge. In addition, the effect of free transition (no grit) was investigated. A body was used on all models.

Kruse, R. L.↗

Low-speed longitudinal aerodynamic characteristics through poststall for 21 novel planform shapes

To identify planform characteristics which have promise for a highly maneuverable vehicle, an investigation was conducted in the Langley Subsonic Basic Research Tunnel to determine the low-speed longitudinal aerodynamics of 21 planform geometries. Concepts studied included twin bodies, double wings, cutout wings, and serrated forebodies. The planform models tested were all 1/4-in.-thick flat plates with beveled edges on the lower surface to ensure uniform flow separation at angle of attack. A 1.0-in.-diameter cylindrical metric body with a hemispherical nose was used to house the six-component strain gauge balance for each configuration. Aerodynamic force and moment data were obtained across an angle-of-attack range of 0 to 70 deg with zero sideslip at a free-stream dynamic pressure of 30 psf. Surface flow visualization studies were also conducted on selected configurations using fluorescent minitufts. Results from the investigation indicate that a cutout wing planform can improve lift characteristics; however, cutout size, shape, and position and wing leading-edge sweep will all influence the effectiveness of the cutout configuration. Tests of serrated forebodies identified this concept as an extremely effective means of improving configuration lift characteristics; increases of up to 25 percent in the value of maximum lift coefficient were obtained.

Gatlin, Gregory M.↗