Search NASA⌕ Search

SEARCH · Search NASA

Results for “technology diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

The Landsat Data Continuity Mission Operational Land Imager: Radiometric Performance

The Operational Land Imager (OLI) is one of two instruments to fly on the Landsat Data Continuity Mission (LDCM), which is scheduled to launch in December 2012 to become the 8th in the series of Landsat satellites. The OLI images in the solar reflective part of the spectrum, with bands similar to bands 1-5, 7 and the panchromatic band on the Landsat-7 ETM+ instrument. In addition, it has a 20 nm bandpass spectral band at 443 nm for coastal and aerosol studies and a 30 nm band at 1375 nm to aid in cirrus cloud detection. Like ETM+, spatial resolution is 30 m in the all but the panchromatic band, which is 15 meters. OLI is a pushbroom radiometer with approximately 6000 detectors per 30 meter band as opposed to the 16 detectors per band on the whiskbroom ETM+. Data are quantized to 12 bits on OLI as opposed to 8 bits on ETM+ to take advantage of the improved signal to noise ratio provided by the pushbroom design. The saturation radiances are higher on OLI than ETM+ to effectively eliminate saturation issues over bright Earth targets. OLI includes dual solar diffusers for on-orbit absolute and relative (detector to detector) radiometric calibration. Additionally, OLI has 3 sets of on-board lamps that illuminate the OLI focal plane through the full optical system, providing additional checks on the OLI's response[l]. OLI has been designed and built by Ball Aerospace & Technology Corp. (BATC) and is currently undergoing testing and calibration in preparation for delivery in Spring 2011. Final pre-launch performance results should be available in time for presentation at the conference. Preliminary results will be presented below. These results are based on the performance of the Engineering Development Unit (EDU) that was radiometrically tested at the integrated instrument level in 2010 and assembly level measurements made on the flight unit. Signal-to-Noise (SNR) performance: One of the advantages of a pushbroom system is the increased dwell time of the detectors allowing for significantly higher SNR than equivalent aperture whiskbroom systems. OLI performance based on the EDU at the "typical" radiance level as specified in the OLI requirements document are about 10 times better than ETM+ performance and 2-3 times better than the requirements for OLI (Table 1).

Markham, Brian↗
NASA NTRS1987

Ti:LiNbO3 components for a fiber gyroscope

It is maintained that integrated optics will play a major role in the next generation of fiber gyros since the potential exists for mass producing low-cost integrated gyro front-end circuits. Ti:LiNbO3 wave guide technology has been used to demonstrate all the necessary components. The combined use of the 3dB splitter and polarizer functions in a 3 x 3 directional coupler is considered. Such a device was designed for operation at lambda = 1.3 microns and fabricated with 6.5-micron Ti strip widths, and a 1050 C/6 hr diffusion.

Minford, W. J.↗
NASA NTRS1989

Quantitative NDE applied to composites and metals

Research at the NASA/Langley Research Center concerning quantitative NDE of composites and metals is reviewed. The relationship between ultrasonics and polymer cure is outlined. NDE models are presented, which can be used to develop measurement technologies for characterizing the curing of a polymer system for composite materials. The models can be used to determine the glass transition temperature, the degree of cure, and the cure rate. The application of the model to control autoclave processing of composite materials is noted. Consideration is given to the use of thermal diffusion models combined with controlled thermal input measurements to determine the thermal diffusivity of materials. Also, a two-dimensional physical model is described that permits delaminations in samples of Space Shuttle Solid Rocket Motors to be detected in thermograms in the presence of cooling effects and uneven heating.

Heyman, Joseph S.↗
NASA NTRS1980

Image Properties of an X-Ray Telescope of the Wolter-1 Type with Emphasis on Contrast Reduction by Diffuse Reflection

Theoretical and experimental results are presented on the geometrical-optic imaging properties of a Wolter-1 type paraboloid-hyperboloid X-ray telescope. Particular consideration is given to the effect of microroughness of the mirror on the imaging properties. Experiments were conducted in which scattering properties were determined as a function of wavelength, incidence angle, and roughness of the plane mirrors. Results indicate the need for optimization of mirror material and polishing technology as well as the development of improved mirror manufacturing techniques. The use of transmission gratings along with the Wolter-1 type telescope in spectroscopy applications is discussed.

Lenzen, R.↗
NASA NTRS1994

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 43: The role of information resource training in aerospace education. Expanded version

Information resource instruction for undergraduate aerospace engineering students has traditionally been limited to an occasional part of the education process--a written paper required in the capstone design course or a library tour. Efforts to encourage the use of aerospace literature and information resources have been made in the past decade, with a recent push from information and, especially, networking technology. This paper presents data from a survey of U.S. aerospace engineering students regarding their instruction in the use of information resources. We find that more than 25 percent of the students surveyed had no instruction in technical communications skills or the use of information resources. We consider the need for instruction in the use of information resources and technical communications skills and the opportunities presented for improvement.

Lawrence, Barbara↗
NASA NTRS1992

Formed platelets for low cost regeneratively cooled rocket combustion chambers

Formed platelet technology can be used to fabricate LO2/LH2-fueled rocket propulsion chambers with higher heat capacity, higher cycle life, and lower pressure drops, in conjunction with lower costs due to the application of high volume production methods. The formed-platelet combustor liner is an assembly of identical platelets, each of which is composed of diffusion-bonded, photoetched laminae with coolant flow passages; the platelets are also joined by diffusion bonding to form the combustor's circumference. Attention is given to the fabrication of a platelet combustion chamber generating 40 Klbf of thrust.

Burkhardt, W. M.↗
NASA NTRS1997

Joining of Silicon Carbide-Based Ceramics by Reaction Forming Method

Recently, there has been a surge of interest in the development and testing of silicon-based ceramics and composite components for a number of aerospace and ground based systems. The designs often require fabrication of complex shaped parts which can be quite expensive. One attractive way of achieving this goal is to build up complex shapes by joining together geometrically simple shapes. However, the joints should have good mechanical strength and environmental stability comparable to the bulk materials. These joints should also be able to maintain their structural integrity at high temperatures. In addition, the joining technique should be practical, reliable, and affordable. Thus, joining has been recognized as one of the enabling technologies for the successful utilization of silicon carbide based ceramic components in high temperature applications. Overviews of various joining techniques, i.e., mechanical fastening, adhesive bonding, welding, brazing, and soldering have been provided in recent publications. The majority of the techniques used today are based on the joining of monolithic ceramics with metals either by diffusion bonding, metal brazing, brazing with oxides and oxynitrides, or diffusion welding. These techniques need either very high temperatures for processing or hot pressing (high pressures). The joints produced by these techniques have different thermal expansion coefficients than the ceramic materials, which creates a stress concentration in the joint area. The use temperatures for these joints are around 700 C. Ceramic joint interlayers have been developed as a means of obtaining high temperature joints. These joint interlayers have been produced via pre-ceramic polymers, in-situ displacement reactions, and reaction bonding techniques. Joints produced by the pre-ceramic polymer approach exhibit a large amounts of porosity and poor mechanical properties. On the other hand, hot pressing or high pressures are needed for in-situ displacement reactions and reaction bonding techniques. Due to the equipment required, these techniques are impractical for joining large or complex shaped components.

Singh, M.↗
NASA NTRS2002

A quantitative comparison of simultaneous BOLD fMRI and NIRS recordings during functional brain activation

Near-infrared spectroscopy (NIRS) has been used to noninvasively monitor adult human brain function in a wide variety of tasks. While rough spatial correspondences with maps generated from functional magnetic resonance imaging (fMRI) have been found in such experiments, the amplitude correspondences between the two recording modalities have not been fully characterized. To do so, we simultaneously acquired NIRS and blood-oxygenation level-dependent (BOLD) fMRI data and compared Delta(1/BOLD) (approximately R(2)(*)) to changes in oxyhemoglobin, deoxyhemoglobin, and total hemoglobin concentrations derived from the NIRS data from subjects performing a simple motor task. We expected the correlation with deoxyhemoglobin to be strongest, due to the causal relation between changes in deoxyhemoglobin concentrations and BOLD signal. Instead we found highly variable correlations, suggesting the need to account for individual subject differences in our NIRS calculations. We argue that the variability resulted from systematic errors associated with each of the signals, including: (1) partial volume errors due to focal concentration changes, (2) wavelength dependence of this partial volume effect, (3) tissue model errors, and (4) possible spatial incongruence between oxy- and deoxyhemoglobin concentration changes. After such effects were accounted for, strong correlations were found between fMRI changes and all optical measures, with oxyhemoglobin providing the strongest correlation. Importantly, this finding held even when including scalp, skull, and inactive brain tissue in the average BOLD signal. This may reflect, at least in part, the superior contrast-to-noise ratio for oxyhemoglobin relative to deoxyhemoglobin (from optical measurements), rather than physiology related to BOLD signal interpretation.

Non-NASA Center↗
NASA NTRS1999

Advanced Technology Inlet Design, NRA 8-21 Cycle II: DRACO Flowpath Hypersonic Inlet Design

The report outlines work performed in support of the flowpath development for the DRACO engine program. The design process initiated to develop a hypersonic axisymmetric inlet for a Mach 6 rocket-based combined cycle (RBCC) engine is discussed. Various design parametrics were investigated, including design shock-on-lip Mach number, cone angle, throat Mach number, throat angle. length of distributed compression, and subsonic diffuser contours. Conceptual mechanical designs consistent with installation into the D-21 vehicle were developed. Additionally, program planning for an intensive inlet development program to support a Critical Design Review in three years was performed. This development program included both analytical and experimental elements and support for a flight-capable inlet mechanical design.

Sanders, Bobby W.↗
NASA NTRS2012

Scientific Verification of Faraday Rotation Modulators: Detection of Diffuse Polarized Galactic Emission

The design and performance of a wide bandwidth linear polarization-modulator based on the Faraday effect is described. Faraday Rotation Modulators (FRMs) are solid-state polarization switches that are capable of modulation up to approx 10 kHz. Six FRMs were utilized during the 2006 observing season in the Background Imaging of Cosmic Extragalactic Polarization (BICEP) experiment; three FRMs were used at each of BICEP fs 100 and 150 GHz frequency bands. The technology was verified through high signal-to-noise detection of Galactic polarization using two of the six FRMs during four observing runs in 2006. The features exhibit strong agreement with BICEP fs measurements of the Galaxy using non-FRM pixels and with the Galactic polarization models. This marks the first detection of high signal-to-noise mm-wave celestial polarization using fast, active optical modulation. The performance of the FRMs during periods when they were not modulated was also analyzed and compared to results from BICEP fs 43 pixels without FRMs.

Moyerman, S.↗
NASA NTRS1989

A far ultraviolet rocket-borne spectrograph

A sensitive spectrograph for rocket observations of celestial objects in the 910-1250A band is described. The instrument incorporates a variety of new technologies that allow unprecedented sensitivity in this difficult, but scientifically rewarding, band. It includes a diamond-turned Wolter-Schwarzschild Type II telescope, a conventional Rowland Circle spectrograph, and resistive anode/microchannel plate detectors. It has been launched twice from Woomera, Australia where it performed observations of SN1987A and discovered a new feature in the diffuse UV background.

Cash, Webster↗
NASA NTRS1993

Laboratory experiments in integrated circuit fabrication

The objectives of the experiment are fourfold: to provide practical experience implementing the fundamental processes and technology associated with the science and art of integrated circuit (IC) fabrication; to afford the opportunity for the student to apply the theory associated with IC fabrication and semiconductor device operation; to motivate the student to exercise engineering decisions associated with fabricating integrated circuits; and to complement the theory of n-channel MOS and diffused devices that are presented in the classroom by actually fabricating and testing them. Therefore, a balance between theory and practice can be realized in the education of young engineers, whose education is often criticized as lacking sufficient design and practical content.

Jenkins, Thomas J.↗
NASA NTRS1986

Prediction and rational correlation of thermophoretically reduced particle mass transfer to hot surfaces across laminar or turbulent forced-convection gas boundary layers

A formulation previously developed to predict and correlate the thermophoretically-augmented submicron particle mass transfer rate to cold surfaces is found to account for the thermophoretically reduced particle mass transfer rate to overheated surfaces such that thermophoresis brings about a 10-decade reduction below the convective mass transfer rate expected by pure Brownian diffusion and convection alone. Thermophoretic blowing is shown to produce effects on particle concentration boundary-layer (BL) structure and wall mass transfer rates similar to those produced by real blowing through a porous wall. The applicability of the correlations to developing BL-situations is demonstrated by a numerical example relevant to wet-steam technology.

Gokoglu, Suleyman A.↗
NASA NTRS1998

Off-beam (multiply-scattered) lidar returns from stratus: Cloud-information content and sensitivity to noise - 1

We review the basic multiple scattering theory of off-beam lidar returns from optically thick clouds using the diffusion approximation. The shape of the temporal signal - the stretched pulse - depends primarily on the physical thickness of the cloud whereas its spatial counterpart - the diffuse spot - conveys specific information on the cloud's optical thickness, as do the absolute returns. This makes observation of the weak off-beam lidar returns an attractive prospect in remote sensing of cloud properties. By estimating the signal-to-noise ratio, we show that night-time measurements can be performed with existing technology. By the same criterion, day-time operation is a challenge that can only be met with a combination of cutting-edge techniques in filtering and in laser sources.

Davis, Anthony B.↗
NASA NTRS2001

First Materials Science Research Rack Capabilities and Design Features

The first Materials Science Research Rack (MSRR-1) will accommodate dual Experiment Modules (EM's) and provide simultaneous on-orbit processing operations capability. The first international Materials Science Experiment Module for the MSRR-1 is an international cooperative research activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center. (ESTEC). This International Standard Payload Rack (ISPR) will contain the Materials Science Laboratory (MSL) developed by ESA as an Experiment Module. The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts. Module Inserts currently planned are a Quench Module Insert, Low Gradient Furnace, Solidification with Quench Furnace, and Diffusion Module Insert. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Department (SPD). It includes capabilities for vapor transport processes and liquid metal sintering. This Experiment Module will be replaced on-orbit with other NASA Materials Science EMs.

Schaefer, D.↗
NASA NTRS2001

Shuttle Flight Experiment on USMP-4: In Situ Monitoring of Crystal Growth Using MEPHISTO

This reports on the MEPHISTO-4 experiment on the Space Shuttle Columbia, STS-87, November 19-December 5, 1997. Involved were NASA; the University of Florida at Gainesville; groups from France that developed and built the furnace; the National Institute of Standards and Technology; The University of New South Wales, Australia; and Purdue University. This was a solidification study in which three long rods of Bismuth- 1 at.% Tin were directionally solidified. The goals were to solidify in an environment free of natural convection; to determine the relationship among solidification growth velocity, growth mode, and temperature; and determine the diffusivity of Sn in Bi. The flight samples grew with a planar solid/liquid interface at velocities less than 3.4 gm/s, and cellular growth was present at velocities greater than 6.7 um/s; grain orientation influenced the planar to cellular transition. The temperature gradient in the liquid was 204 K/cm. The s/l interface was flat with slight concavity. Diffusion-dominated conditions were present during MEPHISTO-4. The Seebeck technique was used to determine the s/I interface temperature during growth, however, to date, analysis of the Seebeck results has not yielded a reliable measurement of the interface temperature. The partition coefficient for Bi alloyed with Sn was measured, k = 0.029.

Abbaschian, Reza↗
NASA NTRS1976

Some observations on the characteristics of low-cost silicon sheets

To meet the need for low cost silicon sheet material in the ERDA/JPL photovoltaics program, JPL has initiated a wide ranging technology development effort in crystal growth that includes several different technology thrusts. They range in scope from innovative ingot growth and multislice wafering, to shaped growth techniques, substrate-related processes and hot forming techniques. In this paper, some salient observations on materials resulting from these processes are reported. Included are multiblade wafering-induced damage studies, interface morphology studies on the heat exchanger cast silicon, some diffusion length measurements in thin silicon layers on ceramic substrates, and results on the equilibrium structure found in laser zone ribbon growth.

Digges, T. G., Jr.↗
NASA NTRS1984

Solidification and crystal growth of solid solution semiconducting alloys

Problems associated with the solidification and crytal growth of solid-solution semiconducting alloy crystals in a terrestrial environment are described. A detailed description is given of the results for the growth of mercury cadmium telluride (HgCdTe) alloy crystals by directional solidification, because of their considerable technological importance. A series of HgCdTe alloy crystals are grown from pseudobinary melts by a vertical Bridgman method using a wide range of growth rates and thermal conditions. Precision measurements are performed to establish compositional profiles for the crystals. The compositional variations are related to compositional variations in the melts that can result from two-dimensional diffusion or density gradient driven flow effects ahead of the growth interface. These effects are discussed in terms of the alloy phase equilibrium properties, the recent high temperature thermophysical data for the alloys and the highly unusual heat transfer characteristics of the alloy/ampule/furnace system that may readily lead to double diffusive convective flows in a gravitational environment.

Lehoczky, S. L.↗