Reversible planar gliding and microcracking in a single-crystalline Ni-rich cathode
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Search NASA
Results for “tensile behavior”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications
Oak Ridge National Laboratory is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys for accident tolerant fuel (ATF) cladding. This report presents the characterization of two new ODS FeCrAl tubes by using powder commercially mechanically alloyed by Zoz GmbH, which underwent high-precision tube rolling with two different annealing schedules. This work shows that the ODS FeCrAl tube without recrystallization exhibits consistent mechanical behavior in comparison with a previously produced tube. The second tube, which underwent a full recrystallization step before the final tube rolling step, showed some circumferential cracking and exhibited limited ductility in the axial tube tensile tests. Based on current and prior work on the ODS FeCrAl alloy system, this report compares the current state of the scientific literature on the alloy class with that of wrought FeCrAl without oxide additions. Then, this report makes recommendations for future research directions that should be undertaken to increase the technology readiness level for ODS FeCrAl as a viable ATF candidate material. This report has been submitted as fulfillment of milestone M3FT-20OR020202064 titled, “STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications” for the US Department of Energy Office of Nuclear Energy’s Advanced Fuel Campaign of the Fuel Cycle R&D program.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Microstructural Characterization of AGR-2 TRISO-coated Particle Buffer, IPyC, and Buffer-IPyC Interfaces
Investigating the microstructural, mechanical, and chemical behaviors of Tristructural Isotropic (TRISO) fuel particles is vital for its qualification and use in advanced reactors. Central to the study of TRISO particles is understanding the silicon carbide (SiC) layer's ability to confine fission products, with failure mechanisms linked to chemical degradation following mechanical degradation of the buffer and IPyC layers. Research has been done to quantify the micro-tensile properties of the buffer, inner pyrolytic carbon (IPyC), and buffer-IPyC interlayer regions and their interactions within both irradiated and un-irradiated TRISO particles. Techniques such as atom probe tomography (APT) and transmission electron microscopy (TEM) have also been deployed to examine microstructural defects and fission product distribution in detail. The goal is to understand layer delamination, establish connections between microstructure and mechanical attributes, and inform computational predictions of fuel performance. This work may help refine predictive models of TRISO fuel behavior and facilitating its certification for use in advanced reactors.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Tensile properties of co-rolled Zr/U-10Mo fuel at ambient and elevated temperatures
The United States High Performance Research Reactor (USHPRR) initiative is currently interested in replacing high-enriched uranium fuel in research reactors with high-assay low-enriched uranium fuel. Here, this work aimed to assist in that mission by providing tensile and bend test data on bare U-Mo and tensile test data on co-rolled Zr/U-10Mo plates at differing thicknesses (0.285 mm, 0.300 mm, and 0.465 mm) and temperatures (293 K, 473 K, and 623 K). Yield strength and ultimate tensile strength values are reported along with an in-depth comparison of how temperature, rolling direction, thickness, and the presence of the Zr-interlayer affect mechanical properties. Results showed that yield strength and ultimate tensile strength in Zr/U-10Mo foils lower as temperature increases by approximately 300 MPa from 293 to 473 K, and another 100 MPa from 473 to 623 K. Additionally it was found that with increased temperature, there is less differentiation in fuel necking and delamination behavior, as well as a greater perceived elongation to fracture. The elastic modulus of co-rolled mini-plates does not follow the volumetric rule of mixtures in terms of averaged strength and is actually lower than the reported moduli of both Zr and U-10Mo.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Additive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets
Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.
36 MATERIALS SCIENCE↗
Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld
2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.
36 MATERIALS SCIENCE↗
SDU7 Interior Liner Testing & Evaluation
The Saltstone Disposal Unit 7 (SDU7) project requested the Savannah River National Laboratory (SRNL), Materials Science & Engineering (MS&E) organization to evaluate an alternative bromobutyl liner and adhesives for potential use in SDU7 based on applicable ASTM testing standards. SRNL performed similar testing for the liner system used in SDU6. Bonded and non-bonded samples of the alternative liner (Blair Rubber Marflex™ RCHB60HT) were subjected to specific ASTM tests after immersion in two Saltstone leachate simulants, designated S1 and S2, for 1000 hours at 60 °C. Immersion exposures were performed at the Savannah River Ecology Laboratory (SREL). Post-immersion testing involved mechanical property and hardness testing of base material, lap-shear testing of bonded samples and rubber-to-concrete paver interrogation. The liner exhibited an approximate 40% drop in tensile strength and 25% drop in elongation at failure from baseline values after immersion, though final values are comparable to previous SDU6 liner values and are within liner manufacturer property ranges. Overall lap-shear strength behavior of the four adhesives showed a similar pattern, with short-term reduction and subsequent increase in peak load values. However, ranking of adhesives varied with the metric used for comparison. Two of the four adhesives tested (Normac 900 and REMA SC 4000) showed overall better behavior, collectively considering immersion performance, lap-shear data and bonded paver interrogation. Lap-shear samples bonded with the REMA adhesive showed the best combination of final retained bond strength, 6-week average bond strength and bond failure mode. Only one paver (REMA SC4000) was noted to have no defects after immersion. This document details the testing performed and provides conclusions and recommendations. The testing suggests that SDU liner performance is highly dependent upon seam integrity, which collectively depends on a combination of adhesive properties, installation workmanship and inspection/quality control.
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Exploring the Microstructure-Property Relationship of Mg-Al-Mn alloys enhanced via Friction Stir Processing
Friction Stir Processing (FSP) is a solid-state thermomechanical processing technique that enables local grain refinement, densification, and homogenization of microstructure in metallic components. Here, FSP is applied to thin sheets of high-pressure die cast AM60 to address the porosity and heterogeneities inherent to the casting process. In this work, microstructure characterization is correlated to improvements in the static mechanical properties of the Mg-Al-Mn alloy system at various FSP processing conditions. Notably, there is a significant increase in the ductility and ultimate tensile stress of system following FSP. The dominant deformation mechanisms for the as-cast material and the FSP material are investigated. Finally, the fatigue life improvement is correlated to microstructure modifications that may lead to distinct behavior in crack initiation and crack propagation for the as-cast and FSP material.
Garcia, David↗
Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction
Laser additive manufacturing (AM) of reaction-based metal matrix composites (MMCs) involves highly complex and non-equilibrium material transformation behavior, including melting, dissolution, precipitation, and solidification. Yet, the dynamics and interplay of these phase transformation processes remain poorly understood, posing substantial challenges in identifying the microstructure formation mechanism, and predicting and controlling the microstructure in the printed parts. Here, in this study, we performed the in-situ X-ray diffraction experiment to characterize the phase evolution dynamics of the 316L + 10 vol.%TiC system during laser melting, which provides direct and quantitative insights of the complex phase reaction and evolution dynamics under rapid heating and cooling conditions relevant to additive manufacturing of reaction-based MMCs. Further in-depth thermodynamic and kinetic calculations revealed that most of the phase evolution behavior observed in the in-situ X-ray diffraction experiment cannot be solely explained by widely used equilibrium thermodynamic models, and diffusion-controlled nonequilibrium dissolution and precipitation kinetics must be considered to elucidate the complex phase evolution behavior, including incomplete TiC dissolution, and three-step TiC precipitation. The three distinct types of precipitates generate unique hierarchical TiC micro- and nanostructures, which enhances the yield strength from 513 MPa to 877 MPa by 71 %, tensile strength from 628 MPa to 1054 MPa by 68 %, and Young's modulus from 193 GPa to 221 GPa by 14 %. The findings of our research provide the knowledge foundation for the design of unique microstructures and advanced MMC materials through laser AM.
36 MATERIALS SCIENCE↗
Multiscale dynamic experiments on fiber-reinforced composites with damage assessment using high-speed synchrotron X-ray phase-contrast imaging
We report fiber-reinforced composites (FRCs) have been widely used as protection materials to replace heavier metals. However, predictive capabilities for the impact-induced failure of FRCs have not been well-developed. In this work, we introduced an integrated technique to visualize the dynamic failure of FRCs, with the modified Kolsky bar loading and the high-speed synchrotron X-ray phase-contrast imaging (PCI). We summarize our experimental studies across the FRCs’ structural levels by using this integrated technique, including single-fiber tensile experiments, fiber/matrix debonding experiments, and single-edge notched bending experiments on composite laminates. It is revealed that the high-speed synchrotron X-ray PCI technique possesses sufficient spatial resolution to identify the failure behavior of a single fiber in the 10-μm scale level, as well as temporal resolution to identify the time sequence of internal dynamic damage evolution. The technique can penetrate through the opaque composite sample and provide real-time visualization of small-scale damaging mechanisms such as the embedded fiber’s sliding in the matrix and the fiber’s transverse debonding with the matrix. At an expanding scale, the technique can identify the crack initiation and track the cracking behavior inside a single ply or between different plies of a composite laminate. High-speed visualization inside the material by this integrated technique provides critical deformation and failure information to develop physical understanding of the damage inside composites under impact.
47 OTHER INSTRUMENTATION↗
Cryogenic mechanical behaviors of CrMnFeCoNi high-entropy alloy
The CrMnFeCoNi high-entropy alloy (HEA) exhibits higher yield strength, ultimate strength and ductility at lower temperature. To further clarify the effect of the testing temperature on microstructure evolution, in this study in-situ synchrotron-based high-energy X-ray diffraction tensile tests were carried out from 298 K down to 123 K. The enhanced yield strength of the alloy at cryogenic temperatures can be attributed to the greater lattice distortion prior to plastic deformation. Higher strain hardening rate leads to the simultaneously enhanced strength and ductility of the studied HEA below room temperature. Both dynamic Hall-Petch hardening (twinning) and dislocation hardening provide high work hardening capacity for this alloy during the plastic deformation at cryogenic temperatures. The increased dislocation density and nano-twins at cryogenic temperatures can be attributed to the decrease in the stacking fault energy as the deformation temperature decreases. These studies could provide an in-depth understanding for the strengthening mechanisms of the HEA in different temperature conditions and guide the exploration of HEAs with superb mechanical properties at cryogenic environments.
36 MATERIALS SCIENCE↗
Assessing the viability of a new subsize tensile specimen geometry for evaluation of structural nuclear and additively manufactured materials
The use of subsize specimens in nuclear materials testing has been a subject of ongoing interest due to radiation safety concerns and resource conservation needs. It is also of interest in additive manufacturing (AM), also known as 3D-printing, as subsize specimens can more accurately represent the behavior of the small, intricate geometries often produced using AM. A novel, extremely small geometry, called the Subsize Teeny (SST) was recently developed and is of interest for implementation. Given its extraordinarily small size and the complexities associated with subsize specimen testing, adequate vetting of this geometry is necessary to ensure data quality. Here, a variety of unirradiated nuclear structural materials were tested in the SST geometry and compared against the well-established SSJ3 geometry. In addition, two case studies implementing the SST as a screening geometry for AM materials were also conducted. The question of SST viability was found to be highly nuanced and will often be dependent on the context or application in question. It was determined, however, that the SST is a largely invalid geometry for exceptionally coarse-grained materials or in cases where the physical defect volume equals or exceeds 0.1 % or where the specimen machining parameters result in significant surface alterations. On the other hand, it was determined that the SST may be employed with confidence if the test material is nearly or totally free of physical defects, isotropic, demonstrates homogeneous plastic deformation, and possesses a fine-grained, nearly or totally homogeneous microstructure with at least twelve slip systems.
Additive manufacturing↗
Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials
Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.
36 MATERIALS SCIENCE↗
Origin of Mechanical Enhancement in Polymer Nanoparticle (NP) Composites with Ultrahigh NP Loading
Polymer nanoparticle composites (PNCs) with ultrahigh loading of nanoparticles (NPs) (>50%) have been shown to exhibit markedly improved strength, stiffness, and toughness simultaneously compared to the neat systems of their components. Recent experimental studies on the effect of polymer fill fraction in these highly loaded PNCs reveal that even at low polymer fill fractions, hardness and modulus increase significantly. In this work, we aim to understand the origin of these performance enhancements by examining the dynamics of both polymer and NPs under tensile deformation. We perform molecular dynamics simulations of coarse-grained, glassy polymer in random-close-packed NP packings with a varying polymer fill fraction. We characterize the mechanical properties of the PNC systems, compare the NP rearrangement behavior, and study the polymer segmental and chain-level dynamics during deformation below the polymer glass transition. Finally, our simulation results confirm the experimentally observed increase in modulus at low polymer fill fractions, and we provide evidence that the source of mechanical enhancement is the polymer bridging effect.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Understanding and quantifying electron beam effects during in situ TEM nanomechanical tensile testing on metal thin films
Transmission electron microscopy (TEM) imaging relies on high energy electrons for atomic scale resolution, however, the electrons themselves interact with and may alter the material being imaged. Using an in situ TEM MEMS-based nanomechanical testing technique, the effect of the electron beam (e-beam) on the deformation behavior of nanocrystalline Al and ultrafine-grained Au is investigated and quantified. We show that the e-beam enhances plastic deformation, leading to an increase in plastic strain rate and a decrease in true activation volume V* in Al (28 to 21b 3 , with b being the Burgers vector length). The e-beam has a much weaker effect on Au. The e-beam effect is not caused by knock-on damage, but rather an effective temperature increase due to additional atomic fluctuations provided by the e-beam. The effective temperature increase is larger for Al than Au. This e-beam effect does not change the deformation mechanisms, but instead accelerates the stress-driven, thermally activated plastic deformation. These experiments provide insight into the effects of the e-beam on plastic deformation in different metals and underscore the importance of understanding and quantifying these effects for proper interpretation of measured mechanical properties during in situ TEM experiments.
36 MATERIALS SCIENCE↗
Processing Temperature Effect on Failure Behavior of Unidirectional Thermoplastic Polymer-fiber-reinforced Polymers (PFRPs)
This study aimed to examine the influence of processing temperature on the mechanical and morphological characteristics of unidirectional (UD) thermoplastic polymer-fiber-reinforced polymers (PFRPs), utilizing UHMWPE-polymer-fiber-reinforced HDPE composites as an example. To achieve this objective, UD thermoplastic PFRPs were produced through filament winding and hot pressing techniques, employing five distinct processing temperatures within the range spanning from the melting onset temperature of the polymer matrix to the melting peak temperature of the reinforcing polymer fiber. By conducting the uni-axial tensile tests on the UD UHMWPE-polymer-fiber-reinforced HDPE composites fabricated at different processing temperatures, it was shown that the optimal longitudinal tensile properties of the composites, comparable with glass-fiber-reinforced thermoset or thermoplastic polymers (GFRPs or GFRTPs) can be achieved when the processing temperature does not significantly exceeds the melting onset temperature of the reinforcing polymer fiber. However, when the processing temperature exceeds this threshold, the mechanical properties of the composites are significantly reduced, as evidenced by the transition in the failure morphology from the presence of significant splitting cracks to the occurrence of plastic necking due to the complete melting of the reinforcing polymer fibers in a composite. Particularly, the ductile behavior of the optimal thermoplastic PFRPs investigated in this study is superior than that of carbon-fiber-reinforced thermoset or thermoplastic polymers (CFRPs or CFRTPs) and even GFRPs and GFRTPs. This study not only provides valuable insights into the proper fabrication of high-performance thermoplastic PFRPs but also offers useful experimental data that can aid in the validation and development of computational models, particularly those related to processing modeling.
Qiao, Yao↗
Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L
A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.
36 MATERIALS SCIENCE↗
The physiochemical alteration of flax fibers structuring components after different scouring and bleaching treatments
Scouring and bleaching are essential steps in flax yarn production; however, in many cases, these treatments have relatively low selectivity on non-cellulosic polysaccharides (NCPs) and lignin. Herein, the specific chemical properties of flax fibers through a variety of scouring and/or bleaching procedures are reviewed to understand their correlations with the mechanical and morphological characteristics. The hydrolysis behaviors of hemicellulose and lignin are different from those of cellulose during chlorine-alkali-oxygen (Cl-AO), enzyme-alkali-oxygen (EAO), and alkali-oxygen (AO) treatments, while the structural hemicellulose polysaccharides fractions were not affected by acid pretreatment followed by alkali scouring (AA) treatment. It was found that the unbleached AA treatment improved scouring efficiency to the greatest extent by decreasing 73.3 % of hemicellulose content and 59.8 % of lignin content compared to the untreated flax fibers and obtained the highest tensile strength (6.58 cN/dtex) and elongation (3.73 %). Delignification was more crucial on fiber tenacity and fineness than hemicellulose removal (R 2 = 0.71, 0.79 vs R 2 = 0.46, 0.61). Within the hemicellulose fractions, a corresponding beneficial relationship between the xylan (XYL) composition and flax fiber properties is presented. The correlation of GM and GGM contents in hemicellulose with flax fiber length was significant with R 2 value 0.97 and 0.99, respectively. This work provides insight into the hydrolysis behavior of hemicellulose and a basis for developing scouring and/or bleaching models that can predict fiber properties.
60 APPLIED LIFE SCIENCES↗