Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal test program”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

IN-STEP inflatable antenna experiment

The objectives of the NASA In-Space Technology Experiments Program (IN-STEP) are to validate the deployment of a 14-m inflatable parabolic reflector structure, measure the reflector surface accuracy, and investigate structural damping characteristics under operational conditions. Here, the accomplishment to date and the approach planned for the remainder of the experiment are discussed. In particular, attention is given to the experiment subsystems, the mechanical thermal, and structural characteristics of the reflector, and the ground-based test program.

Freeland, R. E.↗
NASA NTRS1972

Influence of creep damage on the low cycle thermal-mechanical fatigue behavior of two tantalum base alloys

Low cycle fatigue tests have been performed on the tantalum base alloys T-111 and ASTAR 811C with synchronized, independently programmed temperature and strain cycling. The thermal-mechanical cycles applied fell into three basic categories: these were isothermal cycling, in-phase thermal cycling, and out-of-phase thermal cycling. In-phase cycling was defined as tensile deformation associated with high temperature and compressive deformation with low temperature, while out-of-phase thermal cycling was defined as the reverse case. The in-phase thermal cycling had a pronounced detrimental influence on the fatigue life of both alloys, with the life reduction being greater in the solid solution strengthened T-111 alloy than in the carbide strengthened ASTAR 811C alloy. The out-of-phase tests also showed pronounced effects on the fatigue life of both alloys, although not as dramatic.

Sheffler, K. D.↗
DOE OSTI2025

Multiscale Thermal-hydraulic analysis of the MARVEL micro-reactor using coupled MOOSE Subchannel (SCM) and SAM

MARVEL is a natural-convection-cooled sodium-potassium microreactor that is anticipated to generate 85 kilowatts of thermal energy. It will operate within Idaho National Laboratory’s Transient Reactor Test Facility and is being developed by the DOE Microreactor Program. MARVEL will be used to test microreactor applications, evaluate systems for remote monitoring, and develop autonomous control technologies. A thermal-hydraulic computational model of this facility is a valuable tool to study important transients and calculate the safety limits of the micro-reactor design. For this purpose, the authors have chosen to use a multiscale coupled simulation: SCM for modeling the reactor core and SAM for the reactor’s primary cooling system. SCM is MOOSE physics module for subchannel analysis, which was designed to model single-phase flows through liquid-metal cooled, wire-wrapped fuel pin sub-assemblies, ordered in a triangular lattice. The SCM code was modified to be able to model MARVEL’s unique geometry. SAM is a systems analysis module based on the MOOSE framework. It aims to provide fast-running, whole-plant transient analyses capability with improved-fidelity for various advanced reactor types. The coupling between the two SCM and SAM for MARVEL modeling is done implementing a domain over-lapping approach. The resulting coupled simulation can model transients such as reactor startup/shutdown and provide an intermediate fidelity picture of the temperature field and other variables, in the core. Results for the steady-state simulations are presented in the article as well as flow blockage transient.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1976

Environmental charging of spacecraft surfaces: Tests of thermal control materials for use on the global positioning system flight space vehicle. Part 1: Specimens 1 to 5

The NASA/USAF program on Environmental Charging of Spacecraft Surfaces consists of experimental efforts directed toward evaluating the response of materials to the environmental charged particle flux. Samples of thermal blankets and second surface mirrors of the type to be used on the Global Positioning System Flight Space Vehicle were tested to determine their response to electron flux. The primary result observed was that the ground connection of the metal layers of the blanket, as made by the baseline grounding technique using serrated washers and grommets, deteriorated with time at test. The discharges observed on the blankets were the glow type, not the 'lightning' strike observed on past specimens. Testing was performed at ambient laboratory temperatures.

Stevens, N. J.↗
NASA NTRS1992

Calorimetric thermal-vacuum performance characterization of the BAe 80 K space cryocooler

A comprehensive characterization program is underway at JPL to generate test data on long-life, miniature Stirling-cycle cryocoolers for space application. The key focus of this paper is on the thermal performance of the British Aerospace (BAe) 80 K split-Stirling-cycle cryocooler as measured in a unique calorimetric thermal-vacuum test chamber that accurately simulates the heat-transfer interfaces of space. Two separate cooling fluid loops provide precise individual control of the compressor and displacer heatsink temperatures. In addition, heatflow transducers enable calorimetric measurements of the heat rejected separately by the compressor and displacer. Cooler thermal performance has been mapped for coldtip temperatures ranging from below 45 K to above 150 K, for heatsink temperatures ranging from 280 K to 320 K, and for a wide variety of operational variables including compressor-displacer phase, compressor-displacer stroke, drive frequency, and piston-displacer dc offset.

Kotsubo, V. Y.↗
NASA NTRS1983

Graphite/Larc-160 technology demonstration segment test results

A structural test program was conducted on a Celion/LARC-160 graphite/polyimide technology demonstration segment (TDS) to verify the technology. The 137 x 152 cm (54 x 60 in.) TDS simulates a full-scale section of the orbiter composite body flap design incorporating three ribs and extending from the forward cove back to the rear spar. The TDS was successfully subjected to mechanical loads and thermal environments (-170 to 316 C) simulating 100 shuttle orbiter missions. Successful completion of the test program verified the design, analysis, and fabrication methodology for bonded Gr/PI honeycomb sandwich structure and demonstration that Gr/PI composite technology readiness is established.

Morita, W. H.↗
NASA NTRS1980

Time-temperature-stress capabilities of composite materials for advanced supersonic technology application, phase 1

Implementation of metal and resin matrix composites into supersonic vehicle usage is contingent upon accelerating the demonstration of service capacity and design technology. Because of the added material complexity and lack of extensive service data, laboratory replication of the flight service will provide the most rapid method of documenting the airworthiness of advanced composite systems. A program in progress to determine the time temperature stress capabilities of several high temperature composite materials includes thermal aging, environmental aging, fatigue, creep, fracture, and tensile tests as well as real time flight simulation exposure. The program has two parts. The first includes all the material property determinations and aging and simulation exposures up through 10,000 hours. The second continues these tests up to 50,000 cumulative hours. Results are presented of the 10,000 hour phase, which has now been completed.

Kerr, J. R.↗
NASA NTRS1993

Research and development of high thermal stability fuels

Increases in aircraft performance are leading to increases in the thermal stress on the primary aircraft coolant--the fuel. Fuel thermal stability limitations may offset future aircraft performance gains. The Air Force's Wright Laboratory is sponsoring several research programs to address this problem. The development of an additive package for JP-8 to improve its thermal stability is the primary focus of this paper. This program involves extensive testing of fuels and additives in a variety of test devices, culminating in tests in a fuel system simulator and engine tests. These tests involve Air Force personnel, on-site contractors (University of Dayton Research Institute, Systems Research Laboratories), Pratt and Whitney Aircraft Co., additive manufacturers, and Sandia National Laboratory. The test devices include several flowing and static tests, where the behavior of a fuel is investigated in a wide variety of environments. The study of several baseline fuels in these devices has led to some new insights into the mechanisms of fuel thermal (in)stability. It is becoming clear that a fuel's tendency to oxidize (to form peroxides, for example) is often inversely proportional to its tendency to form insoluble deposits.

T Edwards↗
NASA NTRS2001

Thermal Analysis of Next Generation Space Telescope (NGST) Mirrors During Optical Testing in the X-Ray Calibration Facility (XRCF)

The Next Generation Space Telescope (NGST) program and industry partners are developing extremely lightweight mirror designs. NGST development mirrors are being tested at Marshall Space Flight Center. Target temperature for development mirror testing is 35 K. Conduction and radiation are not sufficient to conduct thermal vacuum testing in a reasonable time. Helium gas is injected into the vacuum chamber to accelerate temperature transitions during testing. Free-molecular conduction can be modeled by adapting present thermal analysis techniques.

Page, Tim↗
NASA NTRS2015

Solar Thermal Upper Stage Liquid Hydrogen Pressure Control Testing

High-energy cryogenic propellant is an essential element in future space exploration programs. Therefore, NASA and its industrial partners are committed to an advanced development/technology program that will broaden the experience base for the entire cryogenic fluid management community. Furthermore, the high cost of microgravity experiments has motivated NASA to establish government/aerospace industry teams to aggressively explore combinations of ground testing and analytical modeling to the greatest extent possible, thereby benefitting both industry and government entities. One such team consisting of ManTech SRS, Inc., Edwards Air Force Base, and Marshall Space Flight Center (MSFC) was formed to pursue a technology project designed to demonstrate technology readiness for an SRS liquid hydrogen (LH2) in-space propellant management concept. The subject testing was cooperatively performed June 21-30, 2000, through a partially reimbursable Space Act Agreement between SRS, MSFC, and the Air Force Research Laboratory. The joint statement of work used to guide the technical activity is presented in appendix A. The key elements of the SRS concept consisted of an LH2 storage and supply system that used all of the vented H2 for solar engine thrusting, accommodated pressure control without a thermodynamic vent system (TVS), and minimized or eliminated the need for a capillary liquid acquisition device (LAD). The strategy was to balance the LH2 storage tank pressure control requirements with the engine thrusting requirements to selectively provide either liquid or vapor H2 at a controlled rate to a solar thermal engine in the low-gravity environment of space operations. The overall test objective was to verify that the proposed concept could enable simultaneous control of LH2 tank pressure and feed system flow to the thruster without necessitating a TVS and a capillary LAD. The primary program objectives were designed to demonstrate technology readiness of the SRS concept at a system level as a first step toward actual flight vehicle demonstrations. More specific objectives included testing the pressure and feed control system concept hardware for functionality, operability, and performance. Valuable LH2 thermodynamic and fluid dynamics data were obtained for application to both the SRS concept and to future missions requiring space-based cryogen propellant management.

Moore, J. D.↗
NASA NTRS1996

Radioactive Transfer Models for Saturn and Titan

The infrared spectra of the earth's atmosphere and planetary atmospheres contains information about atmospheric physical and chemical processes. Atmospheric molecular constituents absorb and emit infrared radiation by rotational and vibrational transition. Observed spectra exhibit characteristic features in the electromagnetic spectrum region. Observation of the absorption or thermal emission spectra may be obtained with space-borne high resolution infrared spectrometers in the 10-5000 cm(exp -1) (2-1000 micro-m) spectral region. Information about the atmospheric thermal structure, composition, and the chemical and physical processes of the observed spectral was accomplished. A preliminary version of a P-T retrieval algorithm for Saturn using all three modes for temperature inversion, e.g., CH4-limb, and H2-nadir spectra was completed and tested for accuracy. Radiative transfer and inversion programs were studied and analyzed for applications to infrared limb thermal emission observations of Saturn and Titan from the Cassini Orbiter, as well as Earth's atmosphere. Analysis and modification of the existing radiative transfer and inversion programs for Earth and planetary atmospheres are being made. Data analysis and retrieval of information form the observations by digital calculations were carried out at UAH and MSFC computer. The working program for generating and reading g-k arrays for using the c-k arrays via the c-k method for radiative transfer calculations for desired atmospheric and instrumental parameters was completed, tested for accuracy and resides at the MSFC computer.

Wu, S. T.↗
NASA NTRS1984

Demonstration of transparent solar array module design

This report discusses the design, development, fabrication and testing of IR transparent solar array modules. Three modules, consisting of a baseline design using back surface reflector cells, and two modules using gridded back contact, IR transparent cells, were subjected to vacuum thermal balance testing to verify analytical predictions of lower operating emperature and increased efficiency. As a result of this test program, LMSC has verified that a significant degree of IR transparency can be designed into a flexible solar array. Test data correlates with both steady state and transient thermal analysis.

Pack, G. J.↗
NASA NTRS1978

Thermal performance evaluation of the Calmac (liquid) solar collector

The procedures used and the results obtained during the evaluation test program on the S. N. 1, (liquid) solar collector are presented. The flat plate collector uses water as the working fluid. The absorber plate is aluminum with plastic tubes coated with urethane black. The glazing consists of .040 in fiberglass reinforced polyester. The collector weight is 78.5 pounds with overall external dimensions of approximately 50.3in. x 98.3in. x 3.8in. The following information is given: thermal performance data under simulated conditions, structural behavior under static loading, and the effects of long term exposure to natural weathering. These tests were conducted using the MSFC Solar Simulator.

Usher, H.↗
NASA NTRS1965

Thermal contact conductance between metals in a vacuum environment

Basic heat transfer data for structural materials used in the Saturn 1B/V 1U component case structural design were obtained. The main emphasis is on thermal contact conductance between dissimilar metallic surfaces, since thermal conductivity values within solids have been sufficiently established previously. The test program outline and test results are described. The following materials were tested: aluminum 6061-T6 (12 samples), aluminum 356 (as cast), almag 35 (as cast), magnesium AZ91C-T4 (4 samples), and mag lithium LA-141 (2 samples).

Source record↗
NASA NTRS2001

Testing and Optimization of Electrically Conductive Spacecraft Coatings

This is the final report discussing the work done for the Space Environments and Effects (SEE) Program. It discusses test chamber design, coating research, and test results on electrically thermal control coatings. These thermal control coatings are being developed to have several orders of magnitude higher electrical conductivity than most available thermal control coatings. Most current coatings tend to have a range in surface resistivity from 1,011 to 1,013 ohms/sq. Historically, spacecraft have had thermal control surfaces composed of dielectric materials of either polymers (paints and metalized films) or glasses (ceramic paints and optical solar reflectors). Very seldom has the thermal control surface of a spacecraft been a metal where the surface would be intrinsically electrically conductive. The poor thermal optical properties of most metals have, in most cases, stopped them from being used as a thermal control surface. Metals low infrared emittance (generally considered poor for thermal control surfaces) and/or solar absorptance, have resulted in the use of various dielectric coatings or films being applied over the substrate materials in order to obtain the required optical properties.

Mell, R. J.↗
NASA NTRS2022

Orbital Trade Study for the PREFIRE Mission

The Polar Radiant Energy in the Far-Infrared Experiment (PREFIRE) is a low-cost cubesat-based Earth Science mission selected for rapid implementation through NASAs Earth Ventures-Instrument program. Two cubesats carrying thermal infrared spectrometers (TIRS) in polar orbits will test long-held assumptions regarding radiative balance at long wavelengths where the cold-dry Arctic and Antarctic surfaces expel significant amounts of the earth's radiant energy. Thermal radiometry with better than one micron sampling at wavelengths beyond 15 microns will provide critical observational bounds for inputs into glacier melt and climate change models through improvements in surface emissivities, longwave greenhouse effect parameterizations, and cloud presence/types. Additional information on potential far-infrared surface/atmosphere feedbacks during rapid melt processes may be captured with sub-diurnal revisits of targeted areas. A baseline mission with two cubesats in different orbits provides a means for optimization of sub-diurnal sampling for science purposes. In this presentation we provide details of orbit studies that inform expected sampling metrics. Candidate orbits are modeled in SGP and then TIRS sampling is projected into surface footprints with appropriate geo-location. Matching algorithms then compile statistics for time-delayed revisits between and within the two orbits. Binning of results by latitude allows for abstraction of precession issues as well as for correlations with surface types as defined by radiometric classification schemes. Multiple acceptable pairs of science-driven orbits were found that optimize sampling in areas known to experience rapid melt events. The final choice of PREFIRE orbital parameters includes the systems trade-space, particularly the power budget, as well as the availability of launch opportunities.

"L'Ecuyer, Tristan"↗
NASA NTRS2003

MAP Propulsion System Thermal Design

The propulsion system of the Microwave Anisotropy Probe (MAP) had stringent requirements that made the thermal design unique. To meet instrument stability requirements the system had to be designed to keep temperatures of all components within acceptable limits without heater cycling. Although the spacecraft remains at a fixed 22 sun angle at L2, the variations in solar constant, property degradation, and bus voltage range all significantly affect the temperature. Large portions of the fuel lines are external to the structure and all components are mounted to non-conductive composite structure. These two facts made the sensitivity to the MLI effective emissivity and bus temperature very high. Approximately two years prior to launch the propulsion system was redesigned to meet MAP requirements. The new design utilized hardware that was already installed in order to meet schedule constraints. The spacecraft design and the thermal requirements were changed to compensate for inadequacies of the existing hardware. The propulsion system consists of fuel lines, fill and drain lines/valve, eight thrusters, a HXCM, and a propulsion tank. A voltage regulator was added to keep critical components within limits. Software was developed to control the operational heaters. Trim resistors were put in series with each operational heater circuits and the tank survival heater. A highly sophisticated test program, which included real time model correlation, was developed to determine trim resistors sizes. These trim resistors were installed during a chamber break and verified during thermal balance testing.

Mosier, Carol L.↗
NASA NTRS1991

Optical figure testing of prototype mirrors for JPL's Precision Segmented Reflector (PSR) program

JPL's PSR program is developing enabling technologies for large space telescopes employing segmented optics, and in particular, lightweight, thermally stable mirrors for telescopes operating at sub-mm wavelengths. JPL's vacuum cryointerferometric optical test facility includes a computer-controlled phase shifting interferometer operating at 10.59 microns and laser metrology for measurement of piston and absolute radius of curvature. The optical metrology has been integrated with a large vacuum chamber including a liquid nitrogen shroud capable of radiatively cooling 1.5 meter aperture mirrors down to 150 K. The facility is now being used to characterize prototype mirrors in both their room-temperature 'as-replicated' condition, and under orbital temperature conditions. The performance and limitations of the optical metrology hardware and software components are noted. Representative test results on prototype one meter-class composite mirrors being developed for PSR and related ground-based programs are also presented.

Hochberg, Eric B.↗