Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Drag and distribution measurements of single-element fuel injectors for supersonic combustors

The drag caused by several vortex generating fuel injectors for scramjet combustors was measured in a Mach 2 to 3.5 airstream. Injector drag was found to be strongly dependent on injector thickness ratio. The distribution of helium injected into the stream was measured both in the near field and the far field of the injectors for a variety of pressure ratios. The far field results differed appreciably from measurements in the near field. Injection pressure ratio was found to profoundly influence the penetration. One of the aerowing configurations tested yielded low drag consistent with desirable penetration and spreading characteristics.

Povinelli, L. A.↗
NASA NTRS1974

Distortion in a full-scale bicone inlet with internal focused compression and 45 percent internal contraction

The distortion characteristics were investigated at the subsonic diffuser exit of a full-scale, Mach 2.5, axisymmetric, mixed compression inlet. Performance and steady-state distortion characteristics were obtained at zero and maximum angle of attack and during an inlet unstart-restart sequence. For the configuration with no cowl bleed, steady-state distortion P(max)P(min)P(bar) ranged from 0.10 for critical inlet operation at 0 deg angle-of-attack to 0.306 for supercritical inlet operation at 6.84 deg angle-of-attack. Vortex generators provided a 50 percent reduction in steady-state distortion for critical operation. Bleed has a smaller effect on steady-stated distortion.

Wasserbauer, J. F.↗
NASA NTRS1974

Development of a Fowler flap system for a high performance general aviation airfoil

A two-dimensional wind-tunnel evaluation of two Fowler flap configurations on the new GA(W)-1 airfoil was conducted. One configuration used a computer-designed 29-percent chord Fowler flap. The second configuration was modified to have increased Fowler action with a 30-percent chord flap. Force, pressure, and flow-visualization data were obtained at Reynolds numbers of 2.2 million to 2.9 million. Optimum slot geometry and performance were found to be close to computer predictions. A C sub L max of 3.8 was achieved. Optimum flap deflection, slot gap, and flap overlap are presented as functions of C sub L. Tests were made with the lower surface cusp filled in to show the performance penalties that result. Some data on the effects of adding vortex generators and hinged-plate spoilers were obtained.

Wentz, W. H., Jr.↗
NASA NTRS1977

F-8 supercritical wing flight pressure, Boundary layer, and wake measurements and comparisons with wind tunnel data

Data for speeds from Mach 0.50 to Mach 0.99 are presented for configurations with and without fuselage area-rule additions, with and without leading-edge vortex generators, and with and without boundary-layer trips on the wing. The wing pressure coefficients are tabulated. Comparisons between the airplane and model data show that higher second velocity peaks occurred on the airplane wing than on the model wing. The differences were attributed to wind tunnel wall interference effects that caused too much rear camber to be designed into the wing. Optimum flow conditions on the outboard wing section occurred at Mach 0.98 at an angle of attack near 4 deg. The measured differences in section drag with and without boundary-layer trips on the wing suggested that a region of laminar flow existed on the outboard wing without trips.

Montoya, L. C.↗
NASA NTRS1977

Buffet characteristics of the F-8 supercritical wing airplane

The buffet characteristics of the F-8 supercritical wing airplane were investigated. Wing structural response was used to determine the buffet characteristics of the wing and these characteristics are compared with wind tunnel model data and the wing flow characteristics at transonic speeds. The wingtip accelerometer was used to determine the buffet onset boundary and to measure the buffet intensity characteristics of the airplane. The effects of moderate trailing edge flap deflections on the buffet onset boundary are presented. The supercritical wing flow characteristics were determined from wind tunnel and flight static pressure measurements and from a dynamic pressure sensor mounted on the flight test airplane in the vicinity of the shock wave that formed on the upper surface of the wing at transonic speeds. The comparison of the airplane's structural response data to the supercritical flow characteristics includes the effects of a leading edge vortex generator.

Deangelis, V. M.↗
NASA NTRS1978

Flight evaluation of the transonic stability and control characteristics of an airplane incorporating a supercritical wing

A TF-8A airplane was equipped with a transport type supercritical wing and fuselage fairings to evaluate predicted performance improvements for cruise at transonic speeds. A comparison of aerodynamic derivatives extracted from flight and wind tunnel data showed that static longitudinal stability, effective dihedral, and aileron effectiveness, were higher than predicted. The static directional stability derivative was slower than predicted. The airplane's handling qualities were acceptable with the stability augmentation system on. The unaugmented airplane exhibited some adverse lateral directional characteristics that involved low Dutch roll damping and low roll control power at high angles of attack and roll control power that was greater than satisfactory for transport aircraft at cruise conditions. Longitudinally, the aircraft exhibited a mild pitchup tendency. Leading edge vortex generators delayed the onset of flow separation, moving the pitchup point to a higher lift coefficient and reducing its severity.

Matheny, N. W.↗
NASA NTRS1976

Results of static tests of a 1/4 scale model of the Boeing YC-14 powered-lift system

One quarter scale static ground tests of the Boeing YC-14 powered lift system were conducted for correlation with full scale test results. The 1/4 scale model utilized a JT-15D turbofan engine to represent the CF6-50D engine employed on the YC-14 advanced medium STOL transport prototype aircraft. The tests included evaluation of static turning performance, static surface pressure and temperature distributions, fluctuating loads, and accelerations of portions of the wing, flaps, and fuselage. Results are presented for the landing flap configuration over an appropriate range of fan pressure ratio as affected by several variables including ground height and vortex generator modifications. Static turning angles of the order of 60 deg were obtained. The highest surface pressures and temperatures were concentrated over the upper surface of the flaps in the region immediately aft of the upper surface blown nozzle.

Hassell, J. L., Jr.↗
NASA NTRS1979

Subsonic wind-tunnel investigation of leading-edge devices on delta wings (data report)

The drag reduction potential of leading edge devices on delta wings at high lift is presented. Fences, pylon type vortex generators, chordwise slots, and sharp plate extensions were tested on wing models with 60 and 74 degree swept blunt leading edges at angles of attack to 32 degrees. Six component balance and leading edge surface pressure measurements were taken with various geometry and spanwise arrangements of the devices. Tables listing the data, without analysis, are presented.

Dhanvada, M. R.↗
NASA NTRS1980

Low speed test of the aft inlet designed for a tandem fan V/STOL nacelle

An approximately .25 scale model of a Tandem Fan nacelle designed for a Type A V/STOL aircraft configuration was tested in a 10-by-10 foot wind tunnel. A 12 inch, tip driven, turbofan simulator was used to provide the suction source for the aft fan inlet. The front fan inlet was faired over for this test entry. Model variables consisted of a long aft inlet cowl, a short aft inlet cowl, a shaft simulator, blow-in door passages and diffuser vortex generators. Inlet pressure recovery, distortion, inlet angle of attack separation limits were evaluated at tunnel velocities from 0 to 240 knots, angles of attack from -10 to 40 degrees and inlet flow rates representative of throat Mach numbers of 0.1 to 0.6. High inlet performance and stable operation was verified at all design forward speed and angle of attack conditions. The short aft inlet configuration provided exceptionally high pressure recovery except at the highest combination of angle of attack and forward speed. The flow quality at the fan face was somewhat degraded by the addition of blow-in door passages to the long aft inlet configuration due to the pressure disturbances generated by the flow entering the diffuser through the auxiliary air passages.

Rhoades, W. W.↗
NASA NTRS1982

Wire Whip Keeps Spray Nozzle Clean

Air-turbine-driven wire whip is clamped near spray-gun mount. When spray gun is installed, wire whip is in position to remove foam buildup from nozzle face. Two lengths of wire 1 to 2 inches long and about 0.03 inch in thickness are used. Foam spray would be prevented from accumulating on nozzle face by increasing purge flow and cutting vortex-generating grooves inside cap and on nozzle flats.

Carroll, H. R.↗
NASA NTRS1981

Additional testing of the inlets designed for a tandem fan V/STOL nacelle

The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

Ybarra, A. H.↗
NASA NTRS1981

Subsonic pitch-up alleviation on a 74 deg delta wing

Fixed leading-edge devices were investigated for alleviating the low speed pitch-up and longitudinal instability of a 74 deg delta wing model. In wind-tunnel tests, Pylon Vortex Generators were shown to be highly effective, compared to leading-edge fences and slots, in raising the pitch-up angle of attack from 8 deg to 28 deg. The subsonic drag penalty was negligible.

Rao, D. M.↗
NASA NTRS1981

Longitudinal grooves for bluff body drag reduction

Wind tunnel test results are presented for four axisymmetric bluff body configurations in order to determine their effect on form and pressure drag. It was found that drag reductions on the order of 40% are obtainable with an afterbody incorporating four longitudinal 'V' grooves. Although this effect may be due to the functioning of the grooves as longitudinal, continuous vortex generators, it is concluded that further research is needed to elucidate the physical basis of the test results. Optimization of the effect will be useful in base drag reduction for such vehicles as automobiles and cargo aircraft with sharply upswept afterbodies.

Quass, B.↗
NASA NTRS1982

Experimental study of delta wing leading-edge devices for drag reduction at high lift

The drag reduction devices selected for evaluation were the fence, slot, pylon-type vortex generator, and sharp leading-edge extension. These devices were tested on a 60 degree flatplate delta (with blunt leading edges) in the Langley Research Center 7- by 10-foot high-speed tunnel at low speed and to angles of attack of 28 degrees. Balance and static pressure measurements were taken. The results indicate that all the devices had significant drag reduction capability and improved longitudinal stability while a slight loss of lift and increased cruise drag occurred.

Johnson, T. D., Jr.↗
NASA NTRS1982

Supercritical maneuvering fighter configuration. Wind-tunnel investigation at Mach numbers of 0.60 to 0.95

A wind tunnel investigation was conducted to study the application of supercritical technology to highly maneuverable combat aircraft. The configuration studied has a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Two supercritical-wing shapes were tested at Mach numbers from 0.60 to 0.95 with angles of attack from -2 deg to 17 deg. On supercritical wing was designed to achieve a high level of transonic maneuver performance at a Mach number of 0.90; however, excessive flow separation developed on this wing at a Mach number of 0.85. A second supercritical wing was tested which had significantly reduced flow separation and improved drag characteristics at a Mach number of 0.85 and maintained the performance of the original wing at the higher Mach numbers. Leading-edge vortex generators did not improve the performance of the second wing; however, a sharp leading-edge flap produced sizable drag reductions at Mach numbers from 0.60 to 0.90.

Mann, M. J.↗
NASA NTRS1974

Dynamic stability characteristics in pitch, yaw, and roll of a supercritical-wing research airplane model

The aerodynamic damping in pitch, yaw, and roll and the oscillatory stability in pitch and yaw of a supercritical-wing research airplane model were determined for Mach numbers of 0.25 to 1.20 by using the small-amplitude forced-oscillation technique. The angle-of-attack range was from -2 deg to 20 deg. The effects of the underwing leading-edge vortex generators and the contributions of the wing, vertical tail, and horizontal tail to the appropriate damping and stability were measured.

Boyden, R. P.↗
NASA NTRS1983

Dynamic Distortion in a Short S-Shaped Subsonic Diffuser with Flow Separation

An experimental investigation of the time varying distortion at the diffuser exit of a subscale HiMAT forebody and inlet was conducted at Mach 0.9 in the Lewis 8 by 6 foot Supersonic Wind Tunnel. A transitory separation was detected within the subsonic diffuser. Vortex generators were installed to eliminate the flow separation. Results from a study of the instantaneous pressure variations at the diffuser exit are presented. The time unsteady total pressures at the diffuser exit are computer interpolated and presented in the form of a movie showing the transitory separation. Limited data showing the instantaneous distortion levels is also presented.

Stumpf, R.↗
NASA NTRS1983

Waterspout, Gust Fronts and Associated Cloud Systems

Nine waterspouts observed on five experimental days during the GATE period of observations are discussed. Primary data used are from 2 aircraft flying in different patterns, one above the other between 30 and 300 m. There is strong evidence associating whirl initiation with cumulus outflow. Computations prepared from estimates of convergence with the region suggest the possibility of vortex generation within 4 minutes. This analysis supports (1) the importance cumulus outflows may have in waterspout initiation and (2) the possibility that sea surface temperature gradients may be important in enabling waterspout development from modest size cumuli.

Simpson, J.↗