SEARCH · Search NASA

Results for “AXIAL FLOW TURBINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Navier-Stokes simulations of rotor-stator interaction using patched and overlaid grids

An accurate numerical analysis of the flows associated with rotor-stator configurations in turbomachinery can be very helpful in optimizing the performance of turbomachinery. In this study the unsteady, thin-layer, Navier-Stokes equations are solved using a system of patched and overlaid grids for a rotor-stator configuration of an axial turbine. The equations necessary for an accurate transfer of information between the several grids are briefly described within the framework of an iterative, implicit algorithm. Results in the form of Mach number contours, time-averaged pressures, unsteady pressures, amplitudes, and phase are presented. The numerical results are also compared with experimental data and the agreement is found to be good.

Rai, M. M.↗

NASA NTRS1976

Small, low cost, expendable turbojet engine. 2: Performance characteristics

A small experimental axial-flow turbojet engine was tested at sea level static conditions and over a range of simulated flight conditions to evaluate its performance as well as to demonstrate the feasibility of low-cost concepts utilized in its design. Testing was conducted at engine speeds as high as 37,000 rpm and at turbine inlet temperatures as high as 1,272 K. For maximum speed the engine produced a net thrust of 3,118 newtons at sea level static operation and 2,318 newtons at its cruise condition of M0 = 0.8 and 6,096 meters. Data obtained over a range of inlet Reynolds number indexes for nominal M0 of 0.38 revealed similar effects or trends on compressor characteristics of those previously established for much larger engines.

Dengler, R. P.↗

NASA NTRS1988

Cryogenic, high speed, turbopump bearing cooling requirements

Although the Space Shuttle Main Engine (SSME) has repeatedly demonstrated the capability to perform during launch, the High Pressure Oxidizer Turbopump (HPOTP) main shaft bearings have not met their 7.5 hour life requirement. A tester is being employed to provide the capability of subjecting full scale bearings and seals to speeds, loads, propellants, temperatures, and pressures which simulate engine operating conditions. The tester design permits much more elaborate instrumentation and diagnostics than could be accommodated in an SSME turbopump. Tests were made to demonstrate the facilities; and the devices' capabilities, to verify the instruments in its operating environment and to establish a performance baseline for the flight type SSME HPOTP Turbine Bearing design. Bearing performance data from tests are being utilized to generate: (1) a high speed, cryogenic turbopump bearing computer mechanical model, and (2) a much improved, very detailed thermal model to better understand bearing internal operating conditions. Parametric tests were also made to determine the effects of speed, axial loads, coolant flow rate, and surface finish degradation on bearing performance.

Dolan, Fred J.↗

DOE OSTI2025

Experimental Investigation of Vapor Formation in Liquid CO2 Flow Through a Converging-Diverging Nozzle

Carbon dioxide is an attractive working fluid for many cycles, including for pumped thermal energy storage (PTES). A challenge with some proposed sCO2 PTES cycles is the operation of sCO2 machinery outside the typical bounds of experience, with local phase change from the liquid state being particularly unknown. Presently, there is insufficient data in the literature regarding multiphase CO2 to adequately design a multiphase-tolerant turbine, so generation of foundational data is required. This experimental study investigates the flow characteristics of sub-sonic liquid CO2 undergoing expansion and phase change in a converging-diverging nozzle. The nozzle is instrumented to measure static pressure, unsteady pressure, temperature, and density. The static pressure transducers are located at 27 axial locations to accurately characterize the pressure profile in the nozzle. High-accuracy RTDs are located at the entrance and exit of the nozzle, and three dynamic pressure transducers are strategically located to capture any unsteady phenomena. During testing, values of mass flow and nozzle inlet pressure are swept to vary the pressure drop and fluid properties. The measured total pressure drop in the nozzle is compared to a homogenous model and the Lockhart-Martinelli correlation method, with the latter predicting loss quite closely. The resulting data set is valuable for validating multiphase numerical models in a simple geometry before implementation of these models in turbomachinery design.

25 ENERGY STORAGE↗

NASA NTRSDate not supplied

Atmospheric, Non-Combusting Droplet Sizing and Spray Imaging Results From a Non-Proprietary Aero Gas Turbine Engine Pressure Swirl Atomizer using Shadowgraphy and Planar Laser Scatter

Members from industry and federal agencies of the United States have developed a collaborating group focused on improving the understanding of the atomization processes common to gas turbine engines. The group is aimed on providing high quality data using x-ray diagnostics in the internal geometry and the near-field dense spray as well as optical diagnostics in the visible spectrum, downstream of the nozzle. This paper reports results from one of the two non-proprietary injectors designs from the group: the primary-secondary injector. In particular, we characterize the spray from only the primary, pressure-swirl atomizing circuit using water through the nozzle. We observed Sauter mean diameter decreased with increased water pressure drop across the nozzle. SMD was also collected at three axial distances and showed decreased size with distance from the nozzle. Planar laser sheet droplet scattering provided qualitative assessment of the spray. Higher water pressure drops provided better atomization than lower pressure drops. The addition of swirling air flow through the injector alleviates and improves the atomization quality, particularly at the lower water pressure drops.

optical diagnostics↗

NASA NTRS1948

Analysis of Effects of Inlet Pressure Losses on Performance of Axial-Flow Type Turbojet Engine

The experimentally determined performance characteristics of an axial-flow turbojet engine have been used to estimate the effects of inlet total-pressure losses on net thrust and specific fuel consumption at a constant engine speed. At low altitudes and flight Mach numbers, inlet pressure losses cause an increase in engine discharge temperature and it is possible that the maximum allowable turbine temperature maybe exceeded. An inlet absolute total-pressure loss of 10 percent will result in a thrust loss of 14 percent and a 15-percent increase in specific fuel consumption based on net thrust. At high altitudes and flight Mach numbers, choking conditions exist in the exhaust nozzle and the inlet pressure losses do not affect the discharge temperatures. Under these conditions, a 10-percent loss in inlet absolute total pressure produces a 22-percent loss in net thrust and a 16-percent increase in specific fuel consumption. If the exhaust-nozzle-outlet area is adjusted to compensate for the effect of inlet losses on discharge temperature in the nonchoking cases (low altitude and Mach numbers), the thrust and fuel consumption will be changed in a manner similar to the results obtained in the choking cases.

Sanders, Newell D↗

NASA NTRS2014

Aerodynamic Measurements of a Variable-Speed Power-Turbine Blade Section in a Transonic Turbine Cascade

The purpose of this thesis is to document the impact of incidence angle and Reynolds number variations on the three-dimensional flow field and midspan loss and turning of a two-dimensional section of a variable-speed power-turbine (VSPT) rotor blade. Aerodynamic measurements were obtained in a transonic linear cascade at NASA Glenn Research Center in Cleveland, Ohio. Steady-state data were obtained for 10 incidence angles ranging from +15.8deg to -51.0deg. At each angle, data were acquired at five flow conditions with the exit Reynolds number (based on axial chord) varying over an order-of-magnitude from 2.12×105 to 2.12×106. Data were obtained at the design exit Mach number of 0.72 and at a reduced exit Mach number of 0.35 as required to achieve the lowest Reynolds number. Midspan tota lpressure and exit flow angle data were acquired using a five-hole pitch/yaw probe surveyed on a plane located 7.0 percent axial-chord downstream of the blade trailing edge plane. The survey spanned three blade passages. Additionally, three-dimensional half-span flow fields were examined with additional probe survey data acquired at 26 span locations for two key incidence angles of +5.8deg and -36.7deg. Survey data near the endwall were acquired with a three-hole boundary-layer probe. The data were integrated to determine average exit total-pressure and flow angle as functions of incidence and flow conditions. The data set also includes blade static pressures measured on four spanwise planes and endwall static pressures.

Flegel, Ashlie B.↗

NASA NTRS1977

Experimental clean combustor program: Turbulence characteristics of compressor discharge flows

The results of turbulence measurements at the entrance to the diffuser duct of a large gas turbine are presented. Hot film and hot wire measurements were conducted over a compressor discharge temperature range of 450K to 608K. It was found that the turbulent intensity at the I.D. and midspan locations increases gradually from 6 + or - 1 percent at idle to 7 + or - 1 percent at approach; the turbulent intensity at the O.D. location increases from 7.5 + or - 0.5 percent at idle to 15 + or - 0.5 percent at approach. The energy in the velocity waves is uniformly distributed over a 0.1 to 5 kHz bandwidth, and the cut-off frequency is not a strong function of the engine operation. The axial length of the Fourier components within this bandwidth varies from 0.021 to 1.05m. The turbulence near the diffuser O.D. is of sufficient amplitude and scale to affect the flow to the front end sections of the burner.

Follansbee, P. S.↗

DOE OSTI2021

The Influence of Pressure on Flame-Flow Characteristics of a Reacting Jet in Crossflow

This work experimentally investigates the effects of elevated combustor pressures on the characteristics of a lean premixed reacting methane/air jet injected into a lean vitiated crossflow using a 12.7 mm axial jet. Experiments were conducted in an axially staged combustor, which implements a reacting jet in crossflow (RJIC) configuration and operates over a pressure range of 1–5 atmospheres. Simultaneous CH* chemiluminescence and particle image velocimetry (PIV) are used to study the flow field and flame behavior. The results show that the reacting jet trajectory exhibits greater penetration with elevated pressure, which is a novel finding compared to available data in the literature. However, the flame liftoff point and ignition delay time both decreased with elevated pressure, which was attributed to decreased vorticity along the flame boundary which corresponds to increased Damköhler numbers (Da). Emissions measurements confirm the NOx increase with pressure as reported in the literature for single-stage gas turbine combustors. Concurrently, emission measurements for the staged configuration show the strong NOx benefit of the RJIC system: the data prove a reduction of global outlet emission levels at elevated pressure with the axially staged configuration. Here, the axial emission reduction was attributed to the decreasing liftoff at elevated pressure levels. Hence, the research emphasizes that the flame and emission characteristics are coupled; they are not only dependent on the geometric parameters and momentum flux ratios but are also a function of pressure.

03 NATURAL GAS↗

NASA NTRS1990

A kinematical/numerical analysis of rotor-stator interaction noise

In this study, the unsteady, thin-layer Navier-Stokes equations are solved using a system of patched grids for a rotor-stator configuration of an axial turbine. The study examines the plurality of spinning modes that are present in such an interaction. The propagation of these modes is analyzed and appropriate grid spacing chosen in the far upstream and downstream regions to attenuate reflections from the computational boundaries. In addition, radiating boundary conditions are implemented based on the farfield acoustical behavior of the flow field. Results in the form of pressure amplitudes and the spectra of turbine tones are presented. Numerical results and experimental data are compared wherever possible. The numerical results are also shown to conform with the predictions of a kinematical analysis of the flowfield.

Rangwalla, Akil A.↗

NASA NTRS1994

Turbine-Driven Pipe-Cleaning Brush

Simple pipe-cleaning device includes small turbine wheel axially connected, by standoff, to circular brush. Turbine wheel turns on hub bearing attached to end of upstream cable. Turbine-and-brush assembly inserted in pipe with cable trailing upstream and brush facing downstream. Water or cleaning solution pumped through pipe. Cable held at upstream end, so it holds turbine and brush in pipe at location to be cleaned. Flow in pipe turns turbine, which turns wheel, producing desired cleaning action. In addition to brushing action, device provides even mixing of cleaning solution in pipe.

Werlink, Rudy J.↗

NASA NTRS1995

Aerodynamic Evaluation of Two Compact Radial-Inflow Turbine Rotors

The aerodynamic evaluation of two highly loaded compact radial turbine rotors was conducted at the NASA Lewis Research Center Small Engine Component Test Facility (SECTF). The experimental results were used for proof-of-concept, for modeling radial inflow turbine rotors, and for providing data for code verification. Two rotors were designed to have a shorter axial length, up to a 10-percent reduced diameter, a lighter weight, and equal or higher efficiencies with those of conventional radial inflow turbine rotors. Three configurations were tested: rotor 1, having a 40-percent shorter axial length, with the design stator (stator 1); rotor 1 with the design stator vanes closed down (stator 2); and rotor 2, slightly shorter axially and having higher loading, with stator 2. The stator had 36 vanes and the rotors each had 14 solid blades. Although presently uncooled, the rotor blades were designed for thicknesses which would allow cooling passages to be added. The overall stage performance measurements and the rotor and stator exit flow field surveys were obtained. Measurements of steady state temperatures, pressures, mass flow rates, flow angles, and output power were made at various operating conditions. Data were obtained at corrected speeds of 80, 90, 100, 110, and 120 percent of design over a range of equivalent inlet-to-exit pressure ratios of 3.5, 4.0, 4.5, and 5.0, the maximum pressure ratio achieved. The test showed that the configuration of rotor 1 with stator 1 running at the design pressure ratio produced a flow rate which was 5.6 percent higher than expected. This result indicated the need to close down the stator flow area to reduce the flow. The flow area reduction was accomplished by restaggering the vanes. Rotor 1 was retested with the closed-down stator vanes and achieved the correct mass flow. Rotor 2 was tested only with the restaggered vanes. The test results of the three turbine configurations were nearly identical. Although the measured efficiencies of the compact designs fell 2 to 3 points below the predicted efficiency of 91 percent, they did meet and exceed by up to 2.5 percentage points the efficiences of state-of-the-art turbines found in the literature.

Simonyi, P. Susan↗

NASA NTRS1999

Blade Heat Transfer Measurements and Prediction in a Transonic Turbine Cascade

Detailed heat transfer measurements and predictions are given for a turbine rotor with 136 deg of turning and an axial chord of 12.7 cm. Data were obtained for inlet Reynolds numbers of 0.5 and 1.0 x 10(exp 6), for isentropic exit Mach numbers of 1.0 and 1.3, and for inlet turbulence intensities of 0.25% and 7.0%. Measurements were made in a linear cascade having a highly three-dimensional flow field resulting from thick inlet boundary layers. The purpose of the work is to provide benchmark quality data for three-dimensional CFD code and model verification. Data were obtained by a steady-state technique using a heated, isothermal blade. Heat fluxes were determined from a calibrated resistance layer in conjunction with a surface temperature measured by calibrated liquid crystals. The results show the effects of strong secondary vortical flows, laminar-to-turbulent transition, shock impingement, and increased inlet turbulence on the surface heat transfer.

Giel, P. W.↗

NASA NTRS1980

Numerical calculation of transonic axial turbomachinery flows

A numerical method and the results of a computer program are presented for solving an exact, three dimensional, full potential equation that models rotating and nonrotating inviscid, absolutely irrotational, homentropic flows. Besides calculating the flows through an arbitrarily shaped rotor or stator blade row mounted on an axisymmetric hub and confined in an axisymmetric duct, the computer program is also capable of analyzing flow fields about arbitrarily shaped wing body combinations, propellers, helicopter rotors in hover, and wind turbine rotors. The governing equation is solved numerically in a fully conservative form by using an artificial time concept, a finite volume technique, rotated type dependent differencing, successive line overrelaxation, and sequential boundary conforming grid refinement. An artificial viscosity is added in fully conservative form, and an initial guess for the potential field is applied, as determined by a two dimensional cascade analysis.

Dulikravich, D. S.↗

NASA NTRS2014

Aerodynamic Effects of Turbulence Intensity on a Variable-Speed Power-Turbine Blade with Large Incidence and Reynolds Number Variations

The effects of inlet turbulence intensity on the aerodynamic performance of a variable speed power turbine blade are examined over large incidence and Reynolds number ranges. Both high and low turbulence studies were conducted in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. The purpose of the low inlet turbulence study was to examine the transitional flow effects that are anticipated at cruise Reynolds numbers. The high turbulence study extends this to LPT-relevant turbulence levels while perhaps sacrificing transitional flow effects. Downstream total pressure and exit angle data were acquired for ten incidence angles ranging from +15.8 to 51.0. For each incidence angle, data were obtained at five flow conditions with the exit Reynolds number ranging from 2.12105 to 2.12106 and at a design exit Mach number of 0.72. In order to achieve the lowest Reynolds number, the exit Mach number was reduced to 0.35 due to facility constraints. The inlet turbulence intensity, Tu, was measured using a single-wire hotwire located 0.415 axial-chord upstream of the blade row. The inlet turbulence levels ranged from 0.25 - 0.4 for the low Tu tests and 8- 15 for the high Tu study. Tu measurements were also made farther upstream so that turbulence decay rates could be calculated as needed for computational inlet boundary conditions. Downstream flow field measurements were obtained using a pneumatic five-hole pitchyaw probe located in a survey plane 7 axial chord aft of the blade trailing edge and covering three blade passages. Blade and endwall static pressures were acquired for each flow condition as well. The blade loading data show that the suction surface separation that was evident at many of the low Tu conditions has been eliminated. At the extreme positive and negative incidence angles, the data show substantial differences in the exit flow field. These differences are attributable to both the higher inlet Tu directly and to the thinner inlet endwall boundary layer that the turbulence grid imposes.

Turbines↗

NASA NTRS1982

Measurement and evaluation of swirl-type flow in labyrinth seals of conventional turbine stages

The effects of load factor and rotor eccentricity were determined on flow conditions in test series for two stages. The results indicate that swirl-type entry flow follows the rules of potential swirl. Within the labyrinth cavities two spatial separated flow areas are considered. A dominating flow in periphera direction nearly fills the space between the sealing strips and the ceiling of the cavity. Below this flow, an area of axial mass transport is situated, with a slight peripheral component, limited on the nearest surroundings of the seals gap and the rotor surface. Between both flows, an exchange of energy takes place. Within the gaps, flow direction depends on axial velocity and therefore on variable flow contraction. A balance of energy within the seal and the cavities interprets the results of lateral force measurements as an influence of friction at the sealing strips surface and the rotating shaft surface. Stages with their blades put together in buckets by means of shrouding segments are particularly influenced by the rotating speed of the shrouding.

Hauck, L.↗

NASA NTRS1994

Computational fluid dynamics analysis in support of the simplex turbopump design

Simplex is a turbopump that is being developed at NASA/Marshall Space Flight Center (MSFC) by an in-house team. The turbopump consists of a single-stage centrifugal impeller, vaned-diffuser pump powered by a single-stage, axial, supersonic, partial admission turbine. The turbine is driven by warm gaseous oxygen tapped off of the hybrid motor to which it will be coupled. Rolling element bearings are cooled by the pumping fluid. Details of the configuration and operating conditions are given by Marsh. CFD has been used extensively to verify one-dimensional (1D) predictions, assess aerodynamic and hydrodynamic designs, and to provide flow environments. The complete primary flow path of the pump-end and the hot gas path of the turbine, excluding the inlet torus, have been analyzed. All CFD analyses conducted for the Simplex turbopump employed the pressure based Finite Difference Navier-Stokes (FDNS) code using a standard kappa-epsilon turbulence model with wall functions. More detailed results are presented by Garcia et. al. To support the team, loading and temperature results for the turbine rotor were provided as inputs to structural and thermal analyses, and blade loadings from the inducer were provided for structural analyses.

Garcia, Roberto↗

NASA NTRS1992

Navier-Stokes analysis of an oxidizer turbine blade with tip clearance

The Gas Generator Oxidizer Turbine (GGOT) Blade is being analyzed by various investigators under the NASA MSFC sponsored Turbine Stage Technology Team design effort. The present work concentrates on the tip clearance region flow and associated losses; however, flow details for the passage region are also obtained in the simulations. The present calculations simulate the rotor blade row in a rotating reference frame with the appropriate coriolis and centrifugal acceleration terms included in the momentum equation. The upstream computational boundary is located about one axial chord from the blade leading edge. The boundary conditions at this location were determined by using a Euler analysis without the vanes to obtain approximately the same flow profiles at the rotor as were obtained with the Euler stage analysis including the vanes. Inflow boundary layer profiles are then constructed assuming the skin friction coefficient at both the hub and the casing. The downstream computational boundary is located about one axial chord from the blade trailing edge, and the circumferentially averaged static pressure at this location was also obtained from the Euler analysis. Results were obtained for the 3-D baseline GGOT geometry at the full scale design Reynolds number. Details of the clearance region flow behavior and blade pressure distributions were computed. The spanwise variation in blade loading distributions are shown, and circumferentially averaged spanwise distributions of total pressure, total temperature, Mach number, and flow angle are shown at several axial stations. The spanwise variation of relative total pressure loss shows a region of high loss in the region near the casing. Particle traces in the near tip region show vortical behavior of the fluid which passes through the clearance region and exits at the downstream edge of the gap.

Gibeling, Howard J.↗