Search NASA⌕ Search

SEARCH · Search NASA

Results for “Accelerated Fuel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Failure investigation and mitigation after experimental research reactor fuel plate deformation in an irradiation device

Experimental research reactor fuel testing is conducted in the Belgian Reactor 2 (BR2) of the Belgian Nuclear Research Centre (SCK CEN) in dedicated irradiation vehicles or rigs. One such vehicle allows flat full-size fuel plates to be irradiated by inserting them into slotted baskets that captures a narrow portion of the longitudinal edges of the plates. The motion of the fuel plates within the baskets is possible within the narrow slots and thus, the plate is considered to be unattached. The design intentionally omits fixing mechanisms of the fuel plates to the baskets to facilitate the inspection and repositioning of the plates between the irradiation cycles and the accommodation of thermal expansion of the plates in the lateral direction. However, loosely inserted fuel plates have weak structural boundary conditions allowing for larger out-of-plane deflections caused by hydrodynamic loads exerted by the flowing coolant, as compared to those of fixed plates. Unexpected large deformations of plates occurred in several irradiation cycles that further resulted in a loss of cladding integrity. These deformations could not be attributed to a single source. This triggered a series of thermal hydraulic, structural, and fluid-structure interaction analyses aiming at understanding the observed phenomenon. The analyses revealed that, for a certain combination of unfavorable manufacturing and assembly tolerances, fuel plate edges could escape out of the slots in the irradiation basket due to the hydrodynamic load. Subsequently, the plate could become wedged inside the basket coolant channel opening. This resulted in reduced coolant flow and accelerated temperature increase and thermal expansion of the plate while under irradiation. This unfavorable feedback loop could then lead to excessive plate surface temperatures, deformed plates and cladding failure, as was observed in the experiments. These analyses not only provided a probable cause of the fuel plate failures, but also resulted in a new and improved design of the irradiation basket to avoid these issues in the future. In conclusion, a series of recent successful irradiations confirm that the sources of failures were identified correctly, and the implemented mitigations were adequate.

BR2↗
DOE OSTI2021

Materials Challenges and Opportunities for Energy Generation, Conversion, Delivery, and Storage (Applied Energy Tri-Laboratory Consortium Workshop Report)

This report documents the outcomes of the Tri-Laboratory Materials Workshop that was held July 31 and August 1, 2019 to begin addressing the needs, opportunities, and challenges associated with the development, fabrication, and testing of the needed materials and components for integrated hybrid energy systems (i.e., incorporating nuclear, fossil, and renewables for electric and thermal applications). This was accomplished by assembling the research program leads and principal investigators at Idaho National Laboratory (INL), National Energy Technology Laboratory (NETL), and National Renewable Energy Laboratory (NREL), who support the research and development of new technology and system integration. The team then identified and prioritized key materials development needs. This effort was intended to enhance communications and synergy among the Tri-Lab partners. Advanced functional and structural materials are central to transformative energy technologies for energy generation, conversion, delivery, and storage. With that in mind, the workshop focused on identifying and assessing the foundational materials research needs at both the basic and applied levels. Materials challenges include the ability to withstand harsh environments, such as high temperatures and pressures, corrosion, oxidation, or irradiation while maintaining flexible mission profiles and long service lifespans. Advanced energy system material challenges and needs range from materials for the capture, upgrading/concentration, storage, and delivery of low-grade heat to materials for high temperature environments that involve liquid metals, molten salt, and very high temperature gas heat delivery and storage systems. Material improvements are needed for hybrid energy systems due to accelerated corrosion and stress-fatigue failure of materials and equipment, which results from increased frequency and amplitude of thermal, mechanical, and electrical cycling of systems components. Multifunctional materials are needed for high temperature solid-oxide fuel cells, advanced electrochemical reactors, and in-process separation. Relative to materials manufacturing, application of advanced additive and subtractive methods need to be understood to develop both thin-layer homogenous materials and materials of graded composition. Materials modeling and machine learning will be critical to accelerate the design and production of power electronics, and nuclear reactor materials and fuel, as well as to gain an understanding of beneficial materials phenomena or deleterious microstructure evolution. There is also a need for standardized models, computational structures, data reporting protocols and modeling tools across the three laboratories. This would allow consistent results, analysis, and data sharing. Combining computational capabilities between the three laboratories (e.g., hardware, software) would greatly increase computational capabilities and throughput. The workshop identified the need for laboratories to anticipate and address problems that will occur during scale-up. Laboratory work must connect with industry to ensure that research focuses on processes that are scalable and marketable. Industry input and perspective are essential to guide laboratory research to meet these requirements and deploy new technology in industrial demonstrations. Another aspect of scale-up is the integration of multiple systems since new challenges often arise at the subsystem interfaces. Establishing a scale-up manufacturing demonstration/pilot plant, potentially as an industrial user facility, would be beneficial to the laboratories and industry. That modular scale-up manufacturing demonstration/pilot plant would allow researchers to find and resolve interface problems that cannot be identified by focusing only on individual parts. Communication exchanges among the organizers, attendees, and workshop survey responses indicate that the workshop was successful in achieving its goal to identify key technology gaps and research needs. Strong positive feedback was received on the sharing of ideas, capabilities, talent, and passion to move forward on the materials-related action items.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemical Characterization of Molten Salt Chemistry During Atmospheric Ingressions

This report describes the salt chemistry and sedimentation studies that were completed in FY23 as part of the Pyrochemical Fuel Cycles – ANL project. The primary objective of these activities was to employ electrochemical methods in order to quantify and gain insights into the reaction mechanisms associated with the interaction of O2 and moisture impurities with the molten chloride salts used for the pyrochemical processing of nuclear materials. If not monitored and controlled, the ingression of these atmospheric impurities can lead to changes in the salt redox conditions and initiate the formation of oxide particles, potentially resulting in operational and safeguards challenges. By elucidating the mechanisms underlying the formation of oxide particles, we can effectively monitor the conditions of the salt and design systems to mitigate the influence of atmospheric O2 and H2O. To achieve these goals, we designed a test system that allowed for precisely controlled gas ingressions into the molten salt vessel. This system included on-line monitoring provided by electrochemical probes that enable near real-time measurements of the salt conditions throughout the course of the experiment. Using this system, we systematically varied experimental conditions, including O2/Ar flow rates and O2 concentrations, to comprehensively understand their impact on solid particle formation. We also used a particle size and shape analyzer to characterize the particles that were generated. Tests in FY23 concentrated on the formation of CeO2 particles, but we also prepared a separate apparatus targeting UO2 particles for use in FY24. We additionally conducted extensive modeling activities in support of this work. This included multiphysics simulations of the gas ingressions along with the development of a machine learning workflow to enable accelerated molecular dynamics modeling of the molten salt chemistry of LiCl-KCl-UCl3. The combination of experimental and modeling tools has allowed us to begin to get a more complete understanding of the reactions that occur when atmospheric ingressions occur in pyroprocessing systems.

Guo, Jicheng↗
DOE OSTI2024

Developing multi-gene CRISPRa/i programs to accelerate DBTL cycles in ABF hosts engineered for chemical production

This project developed and implemented a modular CRISPR activation and interference (CRISPRa/i) platform to accelerate strain optimization and pathway development for industrially relevant microbial hosts. By integrating multiplexed transcriptional perturbation tools with data-driven Design–Build–Test–Learn (DBTL) workflows, the team achieved reductions in cycle time and enhanced production of industrial aromatics, particularly 4-aminocinnamic acid (4-ACA), in Pseudomonas putida. Key accomplishments included: ● Development of a robust, tunable CRISPRa/i system in P. putida that enabled efficient multi-target gene regulation via guide RNA (gRNA) programs ● Completion of two full DBTL cycles, guided by machine learning (ML) models trained on transcriptomic and performance data, reducing engineering time by over 30% ● Optimization of multi-gene regulatory programs to balance expression of host and pathway modules, improve 4-ACA titers, and resolve metabolic bottlenecks ● Demonstration of system portability through a limited proof-of-concept extension in Acinetobacter baylyi, underscoring the generalizability of the approach ● Evaluation of strain performance on lignocellulosic biomass-derived substrates, demonstrating the feasibility of converting renewable carbon into aromatic building blocks These results illustrate the feasibility of applying ML-guided CRISPRa/i perturbation strategies to accelerate strain development in complex microbial systems. The resulting tools and datasets contribute to DOE objectives by improving platform predictability, reducing development costs, and enabling broader access to sustainable, economically viable bioproduction technologies.

09 BIOMASS FUELS↗
DOE OSTI2023

Accelerating polyketide synthase engineering for high TRY production of biofuels and bioproducts (CRADA Final Report)

Polyketide synthase (PKS) enzymes have a modular, deterministic logic that holds the potential to act as a flexible chemical factory for the biological production of a huge diversity of valuable small molecule compounds. However, engineering a custom PKS to produce a specific desired product currently requires years of trial and error, for reasons that remain poorly understood. In this project, we have developed a rapid, high throughput, Design-Build-Test-Learn (DBTL) cycle for polyketide synthases (PKSs) and demonstrate its utility for production of materials precursors. The objectives are 1) to develop a rapid, high-throughput (HT) DBTL cycle for PKSs that will enable production of a large number of unnatural, organic molecules on demand at high titer, rate, and yield (TRY); 2) to demonstrate the utility of the PKS DBTL cycle to produce three molecules: one commodity chemical (caprolactam or valerolactam) and two novel materials precursors (caprolactam or valerolactam derivatives); and 3) to demonstrate the utility of the PKS DBTL cycle to increase the TRY of one molecule (caprolactam or valerolactam). In this project, we have successfully demonstrated our high throughput PKS DBTL pipeline, and have biologically produced valerolactam and several other novel nylon monomers.

09 BIOMASS FUELS↗
DOE OSTI2023

Energy-Efficient Driving in Connected Corridors via Minimum Principle Control: Vehicle-in-the-Loop Experimental Verification in Mixed Fleets

Connected and automated vehicles (CAVs) can plan and actuate control that explicitly considers performance, system safety, and actuation constraints in a manner more efficient than their human-driven counterparts. In particular, eco-driving is enabled through connected exchange of information from signalized corridors that share their upcoming signal phase and timing (SPaT). This is accomplished in the proposed control approach, which follows first principles to plan a free-flow acceleration-optimal trajectory through green traffic light intervals by Pontryagin's Minimum Principle in a feedback manner. Urban conditions are then imposed from exogeneous traffic comprised of a mixture of human-driven vehicles (HVs) - as well as other CAVs. As such, safe disturbance compensation is achieved by implementing a model predictive controller (MPC) to anticipate and avoid collisions by issuing braking commands as necessary. The control strategy is experimentally vetted through vehicle-in-the-loop (VIL) of a prototype CAV that is embedded into a virtual traffic corridor realized through microsimulation. Up to 36% fuel savings are measured with the proposed control approach over a human-modelled driver, and it was found connectivity in the automation approach improved fuel economy by up to 26% over automation without. Additionally, the passive energy benefits realizable for human drivers when driving behind downstream CAVs are measured, showing up to 22% fuel savings in a HV when driving behind a small penetration of connectivity-enabled automated vehicles.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

60 years of science in ICF: from conception to scientific breakeven on the National Ignition Facility

The recent achievements of a burning plasma, fusion ignition, and scientific energy gain with deuterium-tritium (DT) fuel at Lawrence Livermore National Laboratory’s National Ignition Facility (NIF) represents a major milestone in the development of inertial confinement fusion (ICF) and all of fusion research. In these experiments, fuel pressures well in excess of hundreds of GBars were achieved in the compressed fuel, and robust alpha heating of the fuel, far in excess of the energy provided by the implosion, were demonstrated for the first time. These achievements occurred 60 years after the inception of ICF and the first laser demonstration, and were made possible by more than five decades of research at laser facilities around the world. Advances in laser technology both in wavelength and precision, motivated by improved understanding of laser-plasma interaction physics and the demands of targets; improvements in target fabrication inspired by the need to control and minimize hydrodynamic instabilities in the implosion; and multi-dimensional simulations and diagnostics have been critical to this achievement. This paper will summarize the scientific and technical advances, the surprises, and the challenges that had to be overcome to achieve these goals.

fusion↗
DOE OSTI2024

Effect of Thermal Aging on Microstructure and Stress Corrosion Cracking Behavior of an Alloy 152 1st Layer Butter Weldment

Nickel-based Alloy 690 and the associated weld Alloys 52 and 152 are typically used for nozzle penetrations in replacement heads for pressurized water reactor (PWR) vessels, because of their excellent overall resistance to general corrosion and environmental degradation, primarily stress corrosion cracking (SCC). However, many of the existing PWRs are expected to operate for 40- 80 years. Likewise, water-cooled small modular reactors (SMRs) will use Ni-Cr alloys and are expected to receive initial operating licenses for 60 years. Hence, the thermal stability of Ni-Cr alloys is critical for the long-term performance of both existing and advanced nuclear power plants, and possibly spent fuel storage containers. The objective of this research is to understand the microstructural changes occurring in high-Cr, Ni-based Alloy 152 weldments during long time exposure to the reactor operating temperatures, and the effect of these changes on the service performance. One area of particular concern is the potential for long range ordering (LRO), i.e. formation of the intermetallic Ni2Cr phase under prolonged exposure to reactor temperatures and/or irradiation, which can increase strength, decrease ductility, and cause dimensional changes or lead to in-service embrittlement of components made with these alloys. Hence, this research focused on the microstructural evolution and the SCC response of Alloy 152 under accelerated thermal aging. The materials studied involved three heats of Alloy 152 used to produce a dissimilar metal weld (DMW) joining an Alloy 690 plate to an Alloy 533 low alloy steel (LAS) plate, thermally aged at three different temperatures (370°C, 400°C and 450°C) for different durations up to 75,000h (equivalent to 60 years of reactor service). The microstructural characterization by means of synchrotron X-ray conducted in small, 0.2 mm - step line scans in the high-deformation regions of the weld root – covering areas spanning from the weld heat affected zone (HAZ) in Alloy 690 to the weld and weld butter on LAS - did not show evidence of LRO in any of the three Alloy 152 heats aged at 370°C and 450°C to an equivalent of 60 years of service. However, the first weld butter layer has high levels of deformation and is highly susceptible to SCC even in its non-aged condition. Nanohardness testing confirmed the extreme hardening with aging (ΔHV ≅ 100) at two locations within this weldment. In absence of LRO, hardening is suspected to be due to thermally-induced Cr carbide precipitation and coarsening. Testing in a primary water environment of the 1st layer of Alloy 152 weld butter aged at 370°C to a 60-year service equivalent revealed a fatigue and corrosion fatigue crack growth responses similar to those measured on the un-aged alloys. Similarly, the SCC CGR response of the aged weld butter does not appear to show a deterioration in performance, however, the difficult-to-test weldment geometry may affect the test results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Pilot-scale hydrotreating of catalytic fast pyrolysis biocrudes: process performance and product analysis

Catalytic fast pyrolysis (CFP) is a technology option for producing advanced biofuels from hydrocarbon-rich biocrude intermediates. The relatively high oxygen content of biocrudes compared to petroleum intermediates increases hydrogen consumption and the lower thermal stability accelerates catalyst deactivation and reactor fouling hindering the adaptation of hydrotreating technology for biocrude upgrading into biofuels. In this study, four chemically different biocrude feeds were upgraded in a pilot scale hydroprocessing unit at similar process conditions using a commercial hydrodeoxygenation (HDO) catalyst. The biocrude feeds and hydrotreated products were characterized using standard ASTM procedures and advanced analytical techniques (GCxGC-FID and GCxGC-MS). HDO catalyst activity was monitored by changes in physical properties and chemical composition of the upgraded products as a function of time on stream. Aliphatic acids, ketones, aldehydes, and furan derivatives were completely converted during the hydrotreating tests while the concentration of aromatics, aliphatic hydrocarbons and phenolics increased during the hydrotreating tests. The oxygen content, nitrogen content, specific gravity, viscosity and the heavy end of the boiling point range (determined by simulated distillation) of the upgraded products increased with increasing time on stream during hydrotreating. The deactivation rate was the lowest for the biocrude feed that contained the most aliphatic and aromatic hydrocarbons and was the highest for the biocrude feed that had the most anhydrosugars. Overall, the HDO deactivation rate correlates with the total amount of oxygen in the feed (17 wt% to 29 wt%, on a wet basis).

09 BIOMASS FUELS↗
DOE OSTI2024

Enhancing anaerobic digestion of lignocellulosic biomass by mechanical cotreatment

Abstract Background The aim of this study was to increase the accessibility and accelerate the breakdown of lignocellulosic biomass to methane in an anaerobic fermentation system by mechanicalcotreatment: milling during fermentation, as an alternative to conventionalpretreatment prior to biological deconstruction. Effluent from a mesophilic anaerobic digester running with unpretreated senescent switchgrass as the predominant carbon source was collected and subjected to ball milling for 0.5, 2, 5 and 10 min. Following this, a batch fermentation test was conducted with this material in triplicate for an additional 18 days with unmilled effluent as the ‘status quo’ control. Results The results indicate 0.5 – 10 min of cotreatment increased sugar solubilization by 5– 13% when compared to the unmilled control, with greater solubilization correlated with increased milling duration. Biogas concentrations ranged from 44% to 55.5% methane with the balance carbon dioxide. The total biogas production was statistically higher than the unmilled control for all treatments with 2 or more minutes of milling (α = 0.1). Cotreatment also decreased mean particle size. Energy consumption measurements of a lab-scale mill indicate that longer durations of milling offer diminishing benefits with respect to additional methane production. Conclusions Cotreatment in anaerobic digestion systems, as demonstrated in this study, provides an alternative approach to conventional pretreatments to increase biogas production from lignocellulosic grassy material.

Biotechnology & Applied Microbiology↗
DOE OSTI2023

Sulfur poisoning mechanism of LSCF cathode material in the presence of SO 2 : a computational and experimental study

Aiming at the comprehensive understanding of the single sulfur poisoning effect and, eventually, the multiple impurities poisoning phenomena on the SOFC (Solid Oxide Fuel Cell) cathode materials, the sulfur poisoning effect on the (La 0.6 Sr 0.4 ) 0.95 Co 0.2 Fe 0.8 O 3 (LSCF-6428) has been investigated in the presence of 10 ppm SO 2 at 800, 900, and 1000°C, respectively, with a combined computational and experimental approach. The good agreement between the CALPHAD (Computer Coupling of Phase Diagrams and Thermochemistry) simulations and the XRD (X-Ray Diffraction), SEM (Scanning Electron Microscopy), and TEM (Transmission Electron Microscopy) characterization results support the reliability of the CALPHAD approach in the SOFC field. Furthermore, comprehensive simulations were made to understand the impact of temperature, P(SO 2 ), P(O 2 ), and Sr concentration on the threshold of SrSO 4 stability. Results showed that the formation of SrSO4 is thermodynamically favored at lower temperatures, higher P(SO 2 ), higher P(O 2 ), and higher Sr concentration. Finally, comparisons were also made between LSCF-6428 and LSM20 (La 0.8 Sr 0.2 MnO 3 ) using simulations, which confirmed that LSCF-6428 is a poor sulfur-tolerant cathode, in agreement with the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Robotic automation of maintenance work in nuclear power plants a cross-sector survey and roadmap

Nuclear power plants face increasing cost pressures, workforce constraints (aging workforce and skilled labor shortages), and safety requirements that are accelerating interest in robotic systems for inspection and maintenance. We conducted semi-structured interviews with personnel from seven U.S. nuclear utilities and compared deployment models, operational use cases, and integration practices with those reported by participants in the oil, gas, and petrochemical sector. In nuclear plants, robotic use remains concentrated in inspection—particularly indoor unmanned aerial vehicles and submersible remotely operated vehicles—with limited application to physical maintenance tasks. Reported near-term value includes reduced radiological and industrial risk, reduced outage labor, and improved data for planning and condition assessment. Key barriers include integration and data-interoperability constraints, operator qualification requirements, cybersecurity review burden, and difficulty demonstrating reliability in plant-representative environments. Cross-sector benchmarking highlights organizational and deployment practices that may help nuclear plants scale from pilots to routine use. We propose a deployment-oriented roadmap emphasizing modular payload strategies, representative qualification pathways and testing environments, and improved data governance to support safe and economically justified expansion of robotics in operating nuclear power plants.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Synergistic torrefaction of plastic polymers and biomass

This study explores the synergistic torrefaction of biomass and plastics, aimed at enhancing bioenergy production and promoting a circular economy. By leveraging the unique properties of both materials, we investigated the thermochemical transformations occurring during the torrefaction process, from material preparation to the final characteristics of the torrefied product. The biomass used included corn stover (CS) and loblolly pine (LP), while various plastics were categorized from #1 to #7. Torrefaction was conducted at temperatures of 200, 225, and 250 °C, with subsequent extrusion of the torrefied materials and raw materials to produce composite filaments. The results show a consistent decrease in mass yield with increased torrefaction temperature, with notable variations among different biomass-plastic combinations. Co-torrefaction of biomass with polyvinyl chloride and polypropylene resulted in accelerated reaction kinetics, with an observed mass loss rate increase of 15 % at 250 °C compared to the expected rates for individual components. This synergy was quantified, indicating a 20.3 % increase in mass loss for the loblolly pine-polypropylene combination and 23.9 % for corn stover-polypropylene. In contrast, other plastics, including polyethylene terephthalate, high-density polyethylene, low-density polyethylene, polystyrene, and polycarbonate, did not exhibit significant synergistic effects. Mechanical testing indicated that the torrefaction process alters the strength and brittleness of the resulting materials, with implications for their application in bioenergy production and bio-renewable materials. Overall, this research highlights the potential of synergistic torrefaction as a viable strategy for co-processing biomass and plastics, paving the way for innovative solutions in waste management and renewable energy resource development.

09 - BIOMASS FUELS↗
DOE OSTI2024

Highly Efficient Regeneration Module for Carbon Capture Systems in NGCC Applications

The objective of this project is to design, fabricate, and test a highly efficient regeneration module capable of providing an ultra-lean absorption solution that is required for capturing CO 2 from dilute sources at 95% or better efficiency. By integrating this advanced regenerator module with SRI International’s Mixed Salt Process (MSP) absorption modules, SRI expects to demonstrate significant progress toward a reduction in cost of capture versus the DOE reference natural gas combined cycle (NGCC) plant with carbon capture. SRI designed, built, and tested an advanced stripper to enhance the performance of SRI’s MSP for CO 2 capture – a transformational ammonia-based solvent technology – for natural gas (NG) power sources. The testing of the advanced stripper for MSP was conducted at an SRI site using a simulated flue gas stream equivalent to about 10 kWe. The research work included modeling of the advanced stripper and integrating it with the MSP absorbers; studying the strategies for producing very highly alkaline lean solvent with minimized emissions; operating the stripper with advanced heat integration to improve process efficiencies; and collecting critically important data for a detailed techno-economic analysis (TEA). The project tasks were designed to address concerns relating to scale-up and integration of the technology to NG power plants—more specifically, to maximize the carbon capture efficiency achievable with MSP and identify pathways to achieve higher capture efficiencies and ultimately zero net carbon emissions. SRI teamed up with a process modeling company (OLI Systems), a process and chemical engineering company (Trimeric Corporation), and a cost-sharing commercial partner (Baker-Hughes – a leading multinational company that designs, manufactures, and services transformative energy technologies) to execute the project. The research findings will accelerate the MSP development and pave the way for the technology to reach the DOE’s goal, and ultimately commercialization of the MSP technology for low-cost CO 2 capture from NGCC flue gas and other dilute CO 2 sources.

03 NATURAL GAS↗
DOE OSTI2023

Computationally Accelerated Discovery and Experimental Demonstration of High-Performance Materials for Advanced Solar Thermochemical Hydrogen Production

This project achieved its overarching goal of accelerating the discovery and validation of solar thermochemical hydrogen (STCH) materials through a tightly integrated approach that combined high-throughput computational screening, advanced machine learning (ML), and experimental testing. Guided by the objectives outlined in the Statement of Project Objectives (SOPO), our work fulfilled all major milestones across four technical tasks and delivered scientific breakthroughs and practical tools that significantly exceeded the original scope of the project. We began by addressing the challenge of predicting material phase stability through machine learning. A novel Python module was developed to generate thousands of meaningful features from composition, structure, and electronic properties, enabling rapid and reproducible ML model development. Using these tools, we trained a model to predict temperature-dependent Gibbs energies (G(T)) for inorganic crystalline materials with near-chemical accuracy—roughly 40 meV/atom—marking the first such descriptor of its kind. We also introduced a new machine-learned tolerance factor, τ, that accurately predicted perovskite formability with over 90% success, outperforming traditional heuristic models, such as the Goldschmidt tolerance factor. These capabilities allowed for rapid and accurate predictions of phase stability across a vast oxide composition space, setting the stage for high-throughput thermodynamic screening. Building on this foundation, we conducted an extensive computational screening of candidate STCH oxide materials. Over 1.1 million perovskite compositions were evaluated using the τ descriptor, leading to the identification of more than 27,000 predicted stable structures. Using density functional theory (DFT), we refined over 68,000 multinary perovskite structures and computed oxygen vacancy formation energies for over 1,300 ternary and double perovskites. These calculations enabled us to isolate compounds with redox behavior consistent with STCH requirements and resulted in a public dataset now hosted on the Materials Project. Recognizing that thermodynamic screening alone is insufficient, we addressed kinetic limitations by developing a suite of tools to estimate transition state (TS) energies for key redox reactions. We implemented a novel bounding approach that provides lower and upper estimates of TS energies with dramatically reduced computational cost, requiring less than 10% of the CPU time of a full nudged elastic band (NEB) calculation while maintaining high accuracy. This enabled rapid evaluation of over 200 reaction pathways across 90 materials. To further accelerate screening, we developed a SISSO-based ML model to predict diffusion barriers with a 96.7% success rate in classifying fast vs. slow materials, supporting a robust, data-driven framework for assessing redox kinetics. Experimental validation was critical to confirming the predictive power of our models. We synthesized and tested a wide array of candidate materials, including Mn-doped hercynite and several Gd- and La-based perovskites. Notably, Sr 0.4 Gd 0.6 Mn 0.6 Al 0.4 O 3 (SGMA) and Gd 0.5 La 0.5 Co 0.5 Fe 0.5 O 3 (GLCF) emerged as leading STCH materials, exhibiting robust redox cycling and high hydrogen yields exceeding 150 µmol H 2 /g per cycle. These materials also retained over 50% of their hydrogen productivity under high-conversion conditions (H 2 O:H 2 = 1333:1), demonstrating strong thermodynamic favorability and promising performance under industrially relevant scenarios. Additional candidates, such as La 2 MnNiO 6 (L2MN), were found to produce even higher yields than ceria under standard STCH conditions. Our collaborators at Sandia National Laboratories confirmed these findings using high-temperature X-ray diffraction and thermogravimetric analysis, observing stable phase evolution and reversible redox activity. In several respects, the project went beyond the goals initially outlined in the SOPO. We published 17 peer-reviewed articles, including a large dataset of over 66,000 theoretical perovskites and a new structure prediction method (SPuDS-DFT) that accurately identifies ground-state structures at a fraction of the cost of traditional DFT. We demonstrated that our machine-learned G(T) model offers accuracy rivaling quasiharmonic calculations while being orders of magnitude faster. In partnership with the Materials Project, we made our datasets openly available, providing a powerful new resource for the broader materials science community. The combined computational and experimental advances of this project represent a significant advance in STCH materials discovery. By creating a robust, generalizable, and open workflow for thermodynamic and kinetic screening, and validating key findings through synthesis and reactor testing, we have provided a practical and scalable pathway for the rapid identification of new redox-active materials. The tools, data, and materials developed under this project are already supporting ongoing research and have laid the groundwork for the next generation of solar fuel technologies.

08 HYDROGEN↗