Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alumina”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A General Route to Flame Aerosol Synthesis and In Situ Functionalization of Mesoporous Silica

Mesoporous silica is a versatile material for energy, environmental, and medical applications. In this work, for the first time, we report a flame aerosol synthesis method for a class of mesoporous silica with hollow structure and specific surface area exceeding 1000 m 2 /g -1 . We show its superior performance in water purification, drug carrier, and thermal insulation. Moreover, we propose a general route to produce mesoporous nanoshell supported nanocatalysts by in situ decorating active nanoclusters, including noble metal (Pt/SiO 2 ), transition metal (Ni/SiO 2 ), metal oxide (CrO 3 /SiO 2 ), and alumina support (Co/Al 2 O 3 ). As a prototypical application, we perform dry reforming of methane using Ni/SiO 2 , achieving constant 97% CH 4 and CO 2 conversions for more than 200 hours, dramatically outperforming MCM-41 supported Ni catalyst. This work provides a scalable strategy to produce mesoporous nanoshells and proposes an in situ functionalization mechanism to flexible catalysts design for many reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Impact of Alkali and Alkali‐Earth Cations on Ni‐Catalyzed Dimerization of Butene

Abstract The presence of alkali (Na + or Li + ) or alkali‐earth (Ca 2+ or Mg 2+ ) cations adjusting the acid‐base properties on amorphous silica‐alumina influences markedly the catalytic properties of supported Ni for 1‐butene dimerization. The low concentration of Brønsted acid sites on these catalysts reduces the double bond isomerization of butene and inhibits the formation of dimethylhexene as primary product. While the alkali and alkali‐earth cations act as weak Lewis acid sites, only Ni 2+ sites are catalytically active for dimerization of 1‐butene. n ‐Octene and methylheptene are formed selectively as primary products; dimethylhexene is a secondary product. The open environment of the Ni 2+ sites does not induce different reaction pathways compared to Ni 2+ in the pores of zeolites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Hydrotreatment of Nylon 66 and Amide Model Compounds Over Sulfided NiMo Catalysts

Molybdenum sulfide-based catalysts, such as nickel–molybdenum on alumina (NiMoS x /Al 2 O 3 ), are widely used in hydrotreating and have potential for catalyzing waste plastic conversion via hydrogenolysis, yet their performance, such as reaction kinetics and network, for amide-rich polymer feeds is poorly defined. Here we combine Nylon 66 with the amide model compound, N,N-dibutylhexanediamide (DBDAD), to quantify hydrodeoxygenation (HDO) and hydrodenitrogenation (HDN) chemistry in a stirred batch reactor (53 bar H 2 , 280–320°C). DBDAD conversion is near-linear with time, indicating strong adsorption of the substrates on the active sites. Time-resolved product identification indicates parallel C─O first-cleavagedeoxygenation (DO) and C─N first-cleavagedenitrogenation (DN) sequences proceeding through amine and diol intermediates, respectively, to C 4 ─C 6 alkanes. Increasing temperature shifts selectivity toward DN, decreasing the initial r(DO)/r(DN) from 1.38 (280°C) to 0.69 (320°C), with an apparent activation energy of 173 kJ mol −1 for DBDAD conversion. At 300°C, nylon 66 converts faster than DBDAD, producing a complex mixture of oxygen- and nitrogen-containing species and an initial rate ratio r(DO)/r(DN) of 1.6. No heteroaromatic nitrogen products are detected by the method used. These results provide reaction pathways and product signatures relevant to hydro-processing catalysts exposed to polyamide-derived streams.

Nylon 66↗
DOE OSTI2022

Processing and properties of hafnium-doped tin-modified lead zirconate titanate 95/5 ceramics

Niobium (Nb)-doped lead-tin-zirconate-titanate (PSZT) ceramics near the lead-zirconate-titanate 95/5 orthorhombic AFE-rhombohedral FE morphotropic phase boundary (PSZT 13.5/81/5.5 -1.6Nb) were prepared with up to 10 mol.% of hafnium (Hf) substituted for zirconium. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1150°C for 6 h in sealed alumina crucibles with self-same material as the lead vapor source. All compositions were ~98% dense with no detectable secondary phases by X-ray diffraction. The grain size was ~3 μm for all compositions, consisting of equiaxed grains with intergranular porosity. The compositions exhibited remnant polarization values of ~32 μC/cm 2 . Depolarization by the hydrostatic pressure-induced FE-AFE phase transition occurred at 310 MPa for all compositions, resulting in a total depolarization output of 32.4 μC/cm 2 for the PSZT ceramics. Evaluation of the R3c-R3m and R3m-Pm $\bar{3}$ m phase transition temperatures by impedance spectroscopy showed temperatures on heating ranging from 86 to 92°C and 186 to 182°C, respectively, for increasing nominal Hf content. Thermal hysteresis of the phase transitions was also observed in the ceramics, with the transition temperature on cooling being 1–4°C lower. The study demonstrated that the PSZT ceramics are relatively insensitive to variations in Hf content in the range of 0 to 10 mol.%.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Radiative Efficiency and Charge-Carrier Lifetimes and Diffusion Length in Polycrystalline CdSeTe Heterostructures

CdTe-based photovoltaics is a rapidly developing energy technology with one of the lowest levelized costs of electricity. But nonradiative Shockley-Read-Hall (SRH) recombination limits the efficiency of CdTe solar cells. Partial mitigation of bulk and grain-boundary SRH recombination was achieved by alloying CdTe with Se, and CdSe x Te 1-x absorbers are used in high-efficiency solar cells. Recently, interface recombination was significantly reduced with alumina passivation, but other properties of Al 2 O 3 /CdSe x Te 1-x /Al 2 O 3 heterostructures have not yet been investigated. Herein, further progress in understanding and developing polycrystalline heterostructures with x = 0.2 is reported. It is shown that external photoluminescence quantum yield is increased to 0.2%, quasi-Fermi-level splitting to 950 mV, minority carrier lifetimes to 750 ns, and mobility to 100 cm 2 Vs -1 . Such polycrystalline CdSe x Te 1-x electronic characteristics match or exceed CdTe single-crystal properties. The resulting charge-carrier diffusion length of ≈14 $\mu$m is several times greater than the absorber thickness in test structures and in typical CdTe solar cells. Herein, with passivation and absorbers, polycrystalline CdSeTe solar cell open-circuit voltage is increased from the current 76% of the Shockley-Queisser limit to 82%, or close to 1 V is reported.

14 SOLAR ENERGY↗
DOE OSTI2022

Use of Refractory-Volatile Element Deep Eutectic Regions to Grow Single Crystalline Intermetallic Compounds

Compounds containing both refractory and volatile elements present a unique challenge for crystal growth, given the conflicting realities of high melting temperatures and high vapor pressures. Nevertheless, the discovery of superconductivity in FeAs and FeSe based materials and a Weyl semimetal state in TaP are motivations to explore compounds containing such pairs. Here, we discuss use of the low-melting single phase liquid regions above deep M-X eutectics (M=transition metal, X=P, S) as the basis for high temperature solutions for growing intermetallic compounds containing volatile-refractory pairs. We show that Ni-P, Pd-P, Pt-P, and Pd-S compositions form single phase melts at moderate temperatures below 1000 °C and with minimal vapor pressure. We first present the simple case of growing Ni 2 P from Ni-P and next discuss the more complicated growth of RPd 3 S 4 (R=La, Ce, Nd, Eu) from a Pd-S melt. We show how frit-disc alumina crucible sets allow for contamination-free capture of decanted liquid and its reuse in subsequent experiments, demonstrating a fractionation of the CePd 3 S 4 growth to determine the optimal conditions for crystal growth. We conclude by using the single phase liquid regions above the Pt-P and Pd-P eutectics to grow single crystals of MPt 5 P (M=Mn, Fe) and MnPd 5 P. As these materials have primarily been studied in polycrystalline form, we give an overview of the magnetic and transport properties of our single crystals. The examples outlined here illustrate the utility of using the single phase liquid above deep metal-X eutectics for solution growth and materials discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Characterization of the Benefit of APS Flash Coatings in Improving TBC Lifetime

The addition of an air plasma sprayed (APS) “flash” layer on top of a high velocity oxygen fuel (HVOF) bond coating has been shown to extend the lifetime of thermal barrier coatings. A series of furnace cycle tests (FCTs) has been conducted at 1100 °C in air + 10% H 2 O to study the benefit of flash coatings on rod and disk alloy 247 specimens and provide a better mechanistic understanding of their benefit. Flash coatings of NiCoCrAlY and NiCoCrAlYHfSi both improved the FCT lifetime of rod specimens tested in 100-h cycles and disk specimens tested in 1-h cycles. In 1-h cycles, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. Both flash coatings increased the bond coating roughness compared to HVOF. During exposure, the flash layer formed an intermixed alumina-metal layer that appeared to inhibit crack formation. Using a time series of observations, the lower Y + Hf content in the Y-only flash coating appeared to reduce Al consumption. The HVOF layer acted as a source of Al for the adjacent mixed zone. A second series of specimens included a fully APS bond coating where oxide had penetrated through the entire coating to the substrate after only 100, 1-h cycles and lifetime was similar to an HVOF-only bond coating. The inner HVOF layer with the outer APS flash coating prevented this complete penetration from occurring.

Pint, Bruce↗
DOE OSTI2019

Green Synthesis of Aluminium Oxide Nanoparticles and its Applications in Mechanical and Thermal Stability of Hybrid Natural Composites

In the current scenario, biosynthesis has a major trend in the world due to its eco-friendly approach, effectiveness and low cost. In this experiment Aluminium Oxide nano powder was extracted from ‘Muntingia Calabura’ leaf with aluminium nitrate as precursor. An attempt has been made to develop the properties of sisal/coir, sisal/banana and banana/coir based hybrid composite with addition of aluminium oxide (Al{sub 2}O{sub 3}) nano powder. Compression moulding technique was adapted to fabricate the epoxy based natural fiber composites. Nano Al{sub 2}O{sub 3} powder was added in 0, 1, 2 and 3 wt%. The results demonstrate that addition of nano powder up to 3 weight (wt) percentage improvise the tensile, flexural and impact properties for all incorporated hybrid fibers. Residual wt% for sisal/coir, sisal/banana and banana/coir hybrid composites enhanced from 27.15 to 29.14, 26.07 to 31.33% and 23.76 to 27.50% by 3% nano substitution. Degradation temperature improved in different stages of hybrid combinations. Scanning electron microscope (SEM) images clearly showed the reduction of fiber breakage, matrix breakage and void gaps due to alumina nano powder addition.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Exploring Material Solutions for Supercritical CO 2 Applications above 800 °C

There has been recent interest in exploring revolutionary supercritical CO 2 (sCO 2 ) power cycles, and this exploratory investigation was seeking materials with CO 2 compatibility at up to 1200 °C. Here, initial exposures were conducted at 0.1 and 2 MPa CO 2 for up to 1000 h at 900–1200 °C. As expected, specimens of Mo and W that might be used as matrix materials in cermets were rapidly attacked under these conditions. Even an alumina-forming FeCrAlMo alloy showed high mass gains in less than 100 h at 1200 °C due to the formation of Fe-rich oxide. However, at 900–1100 °C, more protective behavior was observed for FeCrAlMo specimens, with or without pre-oxidation, in 0.1 MPa CO 2 , but increased attack was observed in 2 MPa CO 2 . In contrast, most Ni-based alloys exposed at 900–1100 °C showed higher mass gains and thicker reaction products than formed in air. Thus, Ni-based alloys appear less compatible with CO 2 environments above 800 °C compared to lower temperatures. Low mass gains were observed for CVD SiC at 900–1200 °C, but MoSi 2 and Mo(Si,Al) 2 specimens did not form protective scales under these conditions at 1000 and 1100 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Temperature Oxidation Study in a Multi-Oxidant Environment Using 18 O Tracer

The goal of this study was to use 18 O-enriched water to better understand the role of H 2 O in high-temperature oxidation. Seven model and three commercial M-Cr and M-Cr-Al alloys were studied in air with 10% of H 2 O at 800 °C for 5 h. Oxygen from water vapor was more reactive than oxygen from the air and 18 O enriched at the outermost layers of the formed Cr- and Al-rich oxides. Alloys with Al and/or Ti additions showed signs of internal oxidation but 18 O was not enriched inside the alloy in locations with internal oxidation. In conclusion, depending on the alloy Al content, the oxide went from Al oxidation beneath a chromia scale to external alumina scale formation.

18O-enriched water↗
DOE OSTI2022

Investigation of the Mechanisms Underpinning Plasma-Catalyst Interaction for the Conversion of Methane to Oxygenates

Plasma catalysis is a promising approach to further enhance the conversion of methane into value-added products such as methanol. In this work, the mechanisms enabling the conversion of methane to CO, CO 2 and methanol enabled by plasma-enhanced catalysis were investigated. A catalyst reactor was incorporated downstream of the plasma jet to enable the separation between plasma generation and the catalyst bed. An enhancement in CH 3 OH and CO 2 production was observed for the shortest distance between the plasma and catalyst compared to the plasma-only case. Plasma-enabled gas heating was shown not to be responsible for the observed synergy while a gas temperature increase as low as 30-40 K significantly impacted desorption rates of CH 3 OH/C 2 H 5 OH on alumina particles. Correlations between molecular beam mass spectrometry (MBMS) measurements at the inlet and outlet of the catalytic reactor suggest that the observed synergistic effect was caused by radical species most likely the CH 3 O 2 radical. As a result, this study shows that surface reactions induced by radicals such as alkylperoxy radicals might play an important role in surface reactions in plasma-catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Development of a Reliable Kinetic Model for Ladle Refining

Kinetic modeling of ladle refining can be used by steel plants to improve steelmaking and to produce cleaner steels. It can also help researchers to understand the process better. There have been several recent attempts to develop a kinetic model that can predict changes in steel, slag, and inclusion compositions with time. Often the models require parameters that can be difficult to measure under plant conditions, and model limitations have not been discussed in detail. In this study, a two-parameter kinetic model has been developed to predict changes in steel, slag, and inclusion compositions during ladle refining; the two parameters are the mass-transfer coefficient in steel and the inclusion flotation rate constant. The model was based on FactSage macro-processing. Examples of results show that the model can be used to diagnose effects of steel and slag sampling practices and to estimate alloy dissolution time. The model results demonstrate that the presence of solids in slag can significantly reduce the rate of steel–slag reaction while maintaining a high inclusion flotation rate. Some limitations of the model are discussed: the overprediction of calcium transfer to alumina inclusions and the absence of information on inclusions originating from entrained slag.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Red Mud: From Industrial Waste to a Flux for Manufacturing Sustainable Iron/Steel

Here, this study highlights the potential of red mud/bauxite residue, an industrial waste product generated during alumina extraction as a flux for iron and steelmaking. The thermodynamic feasibility of using red mud as a flux in the presence of different reducing agents is evaluated. Potential approaches to decarbonize iron and steel production while utilizing red mud as a flux, as well as the benefits of red mud remnant after iron extraction, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Sensing Capability of Air Plasma-Sprayed SnO{sub 2} Coating in the Presence of Hydrogen and Carbon Monoxide

This report deals with the sensing characteristics of hydrogen (H{sub 2}) and carbon monoxide (CO) gases using a tin oxide (SnO{sub 2}) functional coating deposited on an alumina plate using air plasma spraying technique. This coating exhibits a porous morphology that contains both mesoporous and macroporous regions conducive to superior gas sensing. Initially, gas sensing measurements were performed by varying the operating temperature at a fixed gas concentration using a dynamic sensing setup. The coating showed maximum response % at 275 °C for H{sub 2} and CO gases. However, higher response % was obtained in the presence of H{sub 2} over CO. Sensing performance was further investigated by varying the target gas concentration at 275 °C. The coating exhibited a higher response for H{sub 2} compared to that of other plasma-sprayed SnO{sub 2} coating reported in the literature. The SnO{sub 2} coating under investigation demonstrated good sensor response and repeatability, moderate operating temperature and quick response time.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Role of Oxidation Resistance in High Temperature Alloy Selection for a Future with Green Hydrogen

Hydrogen is being considered integral to the future energy landscape but there is limited mechanistic understanding and a lack of predictive models to describe the combined effects of alloy and gas composition, temperature, thermal cycling and water vapor contents on the oxidation behavior of high-temperature materials. Experimental evaluations were combined with coupled thermodynamic-kinetic modeling to investigate the oxidation behavior of five representative Ni-based superalloys in two water vapor contents (10%, 60% H 2 O) under thermal cycling (1-h, 100-h cyles) conditions at 800°C and 1000°C. The alloy with the highest Ti content demonstrated the poorest cyclic oxidation behavior while the alloy with highest Cr and Al contents was expected to continue to support protective formation of a compact Al 2 O 3 scale. Finally, accelerated degradation of the chromia-forming alloys was observed in the higher water vapor content but the impact on transient oxidation of the alumina-forming alloys needs further investigations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structural complexity of γ-Al 2 O 3 : The nature of vacancy ordering and the structure of complex antiphase boundaries

The structure of γ-Al2O3 remains largely undetermined despite decades of research. This is due to the high degree of disorder, which poses significant challenges for structural analysis using conventional crystallographic approaches. Herein, we study the structure of γ-Al2O3 with Scanning Transmission Electron Microscopy (STEM) and ab-initio calculations to provide a complete structural description. We show that the microstructure can be understood in terms of two key structural features of nanoscale spinel domains and finite thickness segments termed as complex antiphase boundaries (cAPB) that provide the domain interconnectivity. The spinel domains have a distinctive preference for vacancy ordering, which can be rationalized in terms of a structure with a stacking disorder. Tetragonal P4 1 2 1 2 or monoclinic P2 1 models, all based on the identical motif, can be considered as representative ordered forms. Individual spinel domains are interconnected via cAPBs, which adopt a distinct non-spinel bonding environment of δ-Al 2 O 3 . The most common cAPB consists of a single delta motif with thickness of just 0.6 nm on (001), with the resulting displacement a/4 [101]. Remarkably, the cAPBs are shown to energetically stabilize the spinel domains of γ-Al 2 O 3 explaining their high abundance. We demonstrate how the tetragonal distortions naturally arise in this intricate microstructure and place the proposed model in the context of phase transformations to high temperature transition aluminas.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure effects on high velocity microparticle impacts of copper

Constitutive models can fail to predict high-rate deformation behavior due to their inability to account for microstructural effects. In part, this is because of a dearth of experimental benchmarking data in the high strain-rate, low pressure regime, since many high-rate experiments also probe a region of strong shockwaves, at which point microstructure effects no longer play a primary role. This work uses laser-induced particle impact testing to quantitatively study high velocity impacts of small, rigid alumina microspheres on flat copper substrates with varying amounts of initial cold work in the weak shock regime, but at very high strain rates up to ~10 7 s –1 . Through paired experiments and numerical simulations, this work shows that the initial microstructure condition can have significant influence on dynamical mechanical properties in this range. Specifically, prior work hardening of the copper substrate leads to increased rebounding of the microparticles (i.e., less plastic dissipation in the impact) as well as smaller craters. Each of these experimental measurables can be converted into a strength measure, i.e., the dynamic yield strength or dynamic hardness, respectively, neither of which is well predicted consistently by existing constitutive laws. The general trend of hardening can be captured by such models by incorporating an existing “pre-strain,” suggesting that future calibration of the materials parameters may yield a good fit over a broader range of conditions. Our results emphasize the importance of reporting the microstructural condition in dynamic studies, as well as the necessity of accounting for these factors when formulating and optimizing constitutive models.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Physics-coupled data-driven design of high-temperature alloys

We present a materials design loop, which streamlines physics-coupled machine learning (ML) surrogate models to discover new alloy chemistries with improved properties. The efficacy is demonstrated by discovering a high-temperature alumina-forming austenitic (AFA) stainless steel with enhanced creep, followed by experimental validation. The ML models have been trained using a well-curated, highly consistent experimental dataset augmented with synthetic microstructural features from a computational thermodynamic approach. We have populated a large number of hypothetical AFA alloys to explore the high-dimensional composition space and have predicted their creep properties by providing the same synthetic input features obtained from the trained ML models. Uncertainties from the ML training were taken as thresholds for truncating predicted results to identify alloys with improved or deteriorated creep. Individual elemental compositions have been determined via probability density distribution analysis from the group of alloys at the top and bottom of the predicted creep values for further virtual and experimental validations. In conclusion, we anticipate that this workflow can be applied to screen desired conditions, such as chemistry and processing parameters, in high-dimensional space through physics-guided data analytics.

Alloy design↗