Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONDUCTIVE HEAT TRANSFER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Study on Flow Behavior and Heat Transfer Enhancement With Distinct Dimpled Gas Turbine Blade Internal Cooling Channel

Abstract The study presents the investigation on heat transfer distribution along a gas turbine blade internal cooling channel. Six different cases were considered in this study, using the smooth surface channel as a baseline. Three different dimples depth-to-diameter ratios with 0.1, 0.25, and 0.50 were considered. Different combinations of partial spherical and leaf dimples were also studied with the Reynolds numbers of 6,000, 20,000, 30,000, 40,000, and 50,000. In addition to the experimental investigation, the numerical study was conducted using a large eddy simulation (LES) to validate the data. It was found that the highest depth-to-diameter ratio showed the highest heat transfer rate. However, the deepest dimpled channel shows the highest pressure drop, which affects the overall thermal performance of the cooling channel. The results showed that the leaf dimpled surface is the best cooling channel based on the highest Reynolds number's heat transfer enhancement and friction factor. However, at the lowest Reynolds number, partial spherical dimples with a 0.25 depth-to-diameter ratio showed the highest thermal performance.

Energy & Fuels↗
DOE OSTI2020

Residual Stress Modeling with Phase Transformation for Wire Arc Additive Manufacturing of B91 Steel

Wire arc additive manufacturing (WAAM) is an energy-efficient manufacturing technique used for near-net-shape production of functional industrial components. However, heat accumulation during deposition and the associated mechanical and metallurgical changes result in complex residual stress profiles across the cross section of the fabricated components. These residual stresses are detrimental to the service life of the components. In this study, sequentially coupled thermomechanical analysis of WAAM B91 steel is conducted to quantify the residual stress variation across the component. The thermomechanical analysis includes a transient heat transfer model and a static stress model that incorporates the transformation-induced plasticity due to martensitic phase transformation. Here, the experimentally calibrated heat transfer model mirrors the temperature variation of the system during the deposition. The results from the stress model are validated via x-ray diffraction measurements, and the numerical results are in good agreement with the experimental data.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Gas-Phase Temperature Mapping of Evaporating Microdroplets

Evaporation is a ubiquitous and complex phenomenon of importance to many natural and industrial systems. Evaporation occurs when molecules near the free interface overcome intermolecular attractions with the bulk liquid. As molecules escape the liquid phase, heat is removed, causing evaporative cooling. The influence of evaporative cooling on inducing a temperature difference with the surrounding atmosphere as well as within the liquid is poorly understood. Here, we develop a technique to overcome past difficulties encountered during the study of heterogeneous droplet evaporation by coupling a piezo-driven droplet generation mechanism to a controlled micro-thermocouple to probe microdroplet evaporation. The technique allowed us to probe the gas-phase temperature distribution using a micro-thermocouple (50 μm) in the vicinity of the liquid–vapor interface with high spatial (±10 μm) and temporal (±100 ms) resolution. We experimentally map the temperature gradient formed surrounding sessile water droplets having varying curvature dictated by the apparent advancing contact angle (100° ≲ θ ≲ 165°). The experiments were carried out at temperatures below and above ambient for a range of fixed droplet radii (130 μm ≲ R ≲ 330 μm). Our results provide a primary validation of the centuries-old theoretical framework underpinning heterogeneous droplet evaporation mediated by the working fluid, substrate, and gas thermophysical properties, droplet apparent contact angle, and droplet size. We show that microscale droplets residing on low-thermal-conductivity substrates such as glass absorb up to 8× more heat from the surrounding gas compared to droplets residing on high-thermal-conductivity substrates such as copper. Finally, our work not only develops an experimental understanding of the heat transfer mechanisms governing droplet evaporation but also presents a powerful platform for the study and characterization of liquid–vapor transport at curved interfaces wetting and nonwetting advanced functional surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Magnetized ICF implosions: Scaling of temperature and yield enhancement

This work investigates the impact of an applied magnetic field on the yield and hot-spot temperature of inertial confinement fusion implosions. A scaling of temperature amplification due to magnetization is shown to be in agreement with unperturbed two-dimensional (2D) extended-magnetohydrodynamic simulations. A perfectly spherical hot-spot with an axial magnetic field is predicted to have a maximum temperature amplification of 37%. However, elongation of the hot-spot along field lines raises this value by decreasing the hot-spot surface area along magnetic field lines. A scaling for yield amplification predicts that a magnetic field has the greatest benefit for low-temperature implosions; this is in agreement with simplified 1D simulations, but not 2D simulations where the hot-spot pressure can be significantly reduced by heat-flow anisotropy. Simulations including a P2 drive asymmetry then show that the magnetized yield is a maximum when the capsule drive corrects the hot-spot shape to be round at neutron bang time. An applied magnetic field is also found to be most beneficial for implosions that are more highly perturbed, exceeding the theoretical yield enhancement for symmetric hot-spots. Increasing the magnetic field strength past the value required to magnetize the electrons is beneficial due to the additional suppression of perturbations by magnetic tension.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Contribution of the Hydroxyl Group on Interfacial Heat Conduction of Monohydric Alcohols: A Molecular Dynamics Study

Monohydric alcohols have been used as promising phase change materials (PCMs) for low-temperature latent heat storage. However, the heat storage/retrieval rates are limited due to the low thermal conductivity of such alcohols. In this work, nonequilibrium molecular dynamics (NEMD) simulations were performed to study the microscopic heat conduction in example monohydric alcohols, i.e., 1-dodecanol (C12H26O), 1-tetradecanol (C14H30O), and 1-hexadecanol (C16H34O). A simplified ideal crystal model was proposed to exploit the potential for improving the thermal conductivity of monohydric alcohols. The effect of ideal crystalline structures, especially the contribution of the hydroxyl group, on the microscopic heat conduction process was analyzed. The thermal conductivity of the ideal crystals of the various monohydric alcohols was predicted to be more than twice as compared to that of their respective solids. The major thermal resistance in the ideal crystals was found around the molecular interfaces, as a result of the excellent heat conduction performance along the linear molecular chains. The calculated vibrational density of states (VDOS) and interfacial heat transfer were then investigated. When the interfaces are surrounded by hydroxyl groups as walls, strong hydrogen bond (HB) interactions were observed. The interfacial heat transfer coefficient of the ideal crystalline structures of 1-tetradecanol was found to reach up to ~735.6 MW/m2 W. It was elucidated that the high interfacial heat transfer rate is clearly related to the stronger intermolecular interactions.

Engineering↗
DOE OSTI2022

Thermoacoustic Soret separation

In a fluid mixture in a channel with an axial time-averaged temperature gradient, high-amplitude oscillating flow can greatly increase the axial flux of thermal diffusion (Soret) separation of the components of the mixture. The enhancement occurs when the oscillating lateral temperature gradient greatly exceeds the axial gradient, causing a large oscillating concentration that can be favorably time-phased with the oscillating flow. This process can occur even with a negligible pressure oscillation or with a negligible temperature response to pressure, as is the case in most liquid solutions. The thermal boundary condition imposed by realistic solids on thermoacoustic liquids is imperfect, adding mathematical complications that are absent for typical gases, for which the solid surface is temporally isothermal. Compared with gas mixtures, the high Lewis number in typical liquid solutions reduces the separation flux associated with the time-averaged temperature gradient, but it also reduces the remixing associated with the time-averaged mole-fraction gradient. For large enough channels, the second-law separation efficiency is only slightly reduced from that of steady liquid Soret separation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of cold-cap-bottom shear stress on primary foam stability

Here, we analyze the heat transfer between the melt pool and the layer of reacting materials called cold cap, which is the determining factor for the glass production rate in Joule-heated air-bubbled nuclear waste glass melters. We consider the effects of bubbling rate, melt viscosity, melt thermal conductivity, conversion kinetics, and shear rate at the cold-cap bottom, and develop simple relationships for the cold-cap bottom temperature and glass production rate. We show that the melt convection enhances the heat transfer to the cold cap by suppressing the thermal boundary layer and primary foam, while the conversion kinetics opposes these effects. Additionally, we mention how dissolving silica particles affects the primary foam stability and discuss the limitations of the presented approach for vigorously foaming feeds.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Large Eddy Simulation of Low-Reynolds-Number Turbulent Flow of Low-Prandtl-Number Fluid in a Tight Lattice Bundle for Assessment of Reynolds-Averaged Navier-Stokes Turbulence Model

The MARVEL (Microreactor Applications Research Validation and Evaluation) microreactor utilizes natural circulation as core cooling mechanism and liquid metal as a primary coolant. Moreover, the reactor core has a pitch-to-diameter ratio of 1.056, which is considered a tight lattice configuration. Numerous studies have widely reported that Reynolds-Averaged Navier-Stokes (RANS) turbulence models inaccurately predict heat transfer in liquid metals and fail to capture flow pulsations that can occur within tight lattices, leading to further inaccuracies in simulation results. Therefore, evaluating the accuracy of RANS turbulence models in the thermal-hydraulic analysis of the MARVEL microreactor core is crucial for assessing reactor safety. In this study, a Large Eddy Simulation (LES) of the MARVEL microreactor core subchannel was conducted and compared with a RANS simulation to evaluate the accuracies and conservatism of the RANS model. The flow pulsation in a tight lattice predicted by LES enhanced the heat transfer, whereas the RANS model underpredicted it. Consequently, the RANS model predicted the peak cladding temperature higher than the LES model, but the discrepancy between the two approaches was not significant due to the good thermal characteristics of the liquid metal. It can be concluded that the steady-state RANS model is effective for the thermal analysis of liquid-metal-cooled MARVEL microreactor core and can provide conservative predictions from a safety analysis perspective.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2022

Experimental and analytical study of the hydrodynamic and single and two-phase convective heat transfer performance of flexible PDMS microchannels with micropillar arrays

Various copper and silicon based thermal management systems are used in the cooling of electronics. However, the rigid nature of these materials along with their high thermal and electrical conductivity pose a difficulty in developing direct contact embedded flexible cooling systems that can offer robust cooling performance. The low density, thermal stability, chemical inertness, and electrical insulation of Polydimethylsiloxane (PDMS) make it an ideal material to develop lightweight direct contact thermal management systems for electronics. Its ease of fabrication with tunable flexibility provides the opportunity to go beyond traditional electronics and develop advanced active and passive thermal management systems for a wide–range of applications in foldable and wearable electronics, liquid cooling garments, microgravity, and electric motors. In this study, a flexible PDMS based microchannel with micropillar arrays, which enhance the thermal performance of the device through capillary-assisted flow, has been developed. The hydrodynamic and convection heat transfer performance of three PDMS wick pillar geometries, ranging from a porosity of 0.8–0.91, are investigated and compared under single-phase and two-phase conditions. Dielectric coolant FC-3283 is employed and permeability measurements are made for mass fluxes ranging from 53 kg/m 2 s to 369 kg/m 2 s. Given its conformability, the device demonstrates a deviation from Darcy’s Law, within the laminar regime, with an increasing permeability with mass flux at the rate of ~0.5–0.8 Darcy/(kg/m 2 s). A semi-analytical model has been developed and reported to quantify the conformability of the device. The heat transfer performance is experimentally evaluated using the same dielectric fluid for mass flux ranging from 105 kg/m 2 s to 420 kg/m 2 s with heat fluxes ranging from 1.5 W/cm 2 to 16 W/cm 2 . Heat transfer coefficients of up to 7000 W/m 2 K are observed, which are comparable to copper and silicon microchannels. The effect of porosity on the single phase thermal performance has been evaluated against the pumping power to provide a basis for thermal management system design. Finally, high-speed imaging is performed to study the two-phase flow characteristics to provide insight into the vapor formation and removal.

42 ENGINEERING↗
DOE OSTI2021

In-situ thermal transport measurement of flowing fluid using modulated photothermal radiometry

In situ thermal transport measurement of flowing fluid could be useful for the characterization and diagnosis of practical thermal systems such as fluid heat exchangers and thermal energy storage systems. Despite abundant reports on the ex-situ thermal conductivity measurement of stagnant fluids, a suitable technique for the thermal conductivity measurement of flowing fluid has been rarely reported. Here, this paper presents the thermal conductivity measurement of flowing fluid within a pipe using a non-contact modulated photothermal radiometry (MPR) technique, where the surface of the pipe is heated by an intensity-modulated laser and the heat diffuses into the fluid with suitable modulation frequency. We design a tube section with small wall thickness suitable for the MPR measurements to maximize the sensitivity of the thermal response to the fluid properties while minimizing the lateral heat spreading effect. Intrinsic thermal conductivity of different fluids was obtained within a proper range of frequency and flow velocity where the forced convection effect is negligible. The forced convection effect became prominent at high flowing velocity and at low modulation frequency, leading to higher effective thermal conductivity of the fluid. It is found that the intrinsic thermal conductivity could be obtained when the flow velocity is less than 100 mm/sec and Re D 1/2 Pr 1/3 < 100 for DI water and Xceltherm oil under the specified experimental conditions, where Re D is the Reynolds number and Pr is the Prandtl number.

42 ENGINEERING↗
DOE OSTI2025

Local heat transfer measurement in a volumetrically heated TPMS lattice using distributed optical fiber thermal sensing

As additive manufacturing continues to reduce design constraints on heat exchange geometries, methods for high-fidelity local heat transfer measurements in nonconventional channel geometries are critical to their continued development. This study presents a novel method for measuring local heat transfer performance in volumetrically heated lattices using a distributed optical fiber temperature sensor. A diamond-type triply periodic minimal surface (TPMS) lattice, 3D-printed from a conductive polymer, was Joule heated while it was convectively cooled with air. Temperature measurements were taken at the solid–fluid interface across 14 internal locations using a single optical fiber over the Reynolds number range 800–2750. The TPMS lattice achieved up to 312% higher heat transfer coefficients compared to developing flow in a straight tube. A Nusselt number correlation was developed for the diamond TPMS, which showed good agreement with data collected for comparable geometries available in literature. In conclusion, this study presents a robust and new method for experimental measurement of the heat transfer coefficient in complex geometries and helps to understand and quantify the exceptional performance of TPMS heat transfer geometries.

TPMS↗
DOE OSTI2022

Impact of electron transport models on capillary discharge plasmas

Magnetohydrodynamics (MHD) can be used to model capillary discharge waveguides in laser-wakefield accelerators. However, the predictive capability of MHD can suffer due to poor microscopic closure models. Here, we study the impact of electron heating and thermal conduction on the capillary waveguide performance as part of an effort to understand and quantify uncertainties in modeling and designing next-generation plasma accelerators. To do so, we perform two-dimensional high-resolution MHD simulations using an argon-filled capillary discharge waveguide with three different electron transport coefficients models. The models tested include (i) Davies et al., (ii) Spitzer, and (iii) Epperlein–Haines (EH). We found that the EH model overestimates the electron temperature inside the channel by over 20% while predicting a lower azimuthal magnetic field. Furthermore, the Spitzer model, often used in MHD simulations for plasma-based accelerators, predicts a significantly higher electron temperature than the other models suggest.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Effects of Heat Treatment on Microstructure, Thermal Transport and Stability in SRF Niobium

Efficient heat transfer and thermal stability are critical for preventing thermal quench and ensuring the high performance and reliability of superconducting radiofrequency (SRF) cavities, especially under high RF fields. In this article, we investigate thermal conductivity and heat capacity of high-purity cold-worked niobium used in SRF applications, with a particular focus on the effects of high-temperature heat treatments. Our measurements reveal a pronounced sensitivity of thermal transport and thermodynamic properties to the underlying microstructure such as grain size and dislocation density. The results show the critical role of controlled heat treatment processes in optimizing the thermal performance of SRF niobium, providing valuable insights for improving cavity fabrication and processing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Redox conduction facilitates direct interspecies electron transport in anaerobic methanotrophic consortia

Anaerobic methanotrophic archaea (ANME) and sulfate-reducing bacteria (SRB) form syntrophic partnerships in marine sediments to consume greenhouse gas methane. While direct interspecies electron transport is proposed to enable ANME/SRB symbiosis, its electrochemical properties remain uncharacterized. Here, using sediment-free enrichment cultures, we measured the electron transport capabilities of marine consortia under physiological conditions. Diverse ANME/SRB consortia exhibited high dry conductance close to electrogenic biofilms. This conductance diminished upon exposure to heat or oxygen but was preserved following paraformaldehyde fixation, indicating a biomolecular origin for this electric charge transfer. Cyclic voltammetry revealed redox activity centered at 28 ± 11, 94 ± 6, and 24 ± 7 millivolts for ANME-1/Desulfofervidus, ANME-2a/Seep-SRB1, and ANME-2a+2c/Seep-SRB1+2 consortia, respectively. Generator-collector measurements further demonstrated that these redox components facilitate electron transport over micrometer-scale distances, sufficient to link archaeal and bacterial partners. Collectively, our results establish that marine ANME/SRB symbiosis uses redox conduction, consistent with multiheme cytochromec, for direct interspecies electron transport.

Science & Technology - Other Topics↗
DOE OSTI2025

Carbon nanotube coated metal mesh: Bridging nanoscale and macroscale

A novel hybrid structure has been developed by growing carbon nanotubes (CNTs) on a metal mesh that functions as a literally unlimitedly extendable backbone. This hybrid material structure provides a new approach of extending CNTs’ advantageous properties such as ultrahigh thermal and electrical conductivities, high sensitivity to gases, and distinctive wettability for different liquids with chemical inertness to macroscale—otherwise available only in nano- and microscales. In this feasibility work, CNTs were grown on a Type 316 stainless steel (SS) mesh by self-catalytical chemical vapor deposition (CVD) without the need of an externally added catalyst or catalyst support. For the radially aligned and entangled CNT forest on the SS mesh, the average CNT diameter is around 50 nm, while the length varies from 20 to 25 µm. High-resolution transmission electron microscopy analysis revealed the multiwall structure of the CNTs with >30 rolled-up graphitic sheets. Raman spectra of the CNTs showed a dominant G band, indicating a well-ordered graphitic nanostructure. Being highly hydrophobic with a water contact angle of ∼145° and oleophilic, the CNT-coated SS mesh could be used in fluid separation and organic contaminant removal from water. Moreover, CNTs are recognized for their exceptional thermal conductivity and the CNT-coated mesh offers a supportive structure with directly connected CNTs for efficient heat transfer. Proof of concept has been achieved for the CNT-coated mesh’s potentials as a liquid filter and an thermal interface material (TIM). Specifically, the CNT-coated mesh demonstrated the capability of capturing water from a water-organic mixture with a 100 % efficiency while allowing organic liquids to pass through the filter. Furthermore, when used as a TIM, the CNT-coated mesh reduced the interfacial thermal impedance by >30 %.

Carbon nanotubes (CNTS)↗
DOE OSTI2021

Evaluation of the Passive Cooling Potential of Thermal Mass Inherent in Medium to Large Commercial Buildings

Typical commercial construction inherently contains large surface areas of relatively thin mass located in the floor slabs. This research asks how effective this mass could be for passive cooling, relative to other mass depths, if it were to be exposed and used as thermal mass. Although much of the rich literature on thermal mass has been conducted with far greater mass depths, a more limited amount of research suggests that because the surface heat transfer rate is limited, the focus should be on the surface area of exposed mass, not its depth. This presents an opportunity for more buildings to behave more thermally massively, if the mass inherent in typical floor slabs contains utility, particularly over diurnal cycles. In all climates analyzed, it was found that there is a pronounced shoulder where energy savings from passive cooling of increasing mass depths was steep until roughly 7.5–10 cm, and beyond this point the achieved energy savings diminished rapidly. When considering the embodied energy of concrete, the incremental benefit of added mass beyond a typical topping slab of 10 cm does not justify the incremental embodied energy cost from a total energy standpoint alone.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Coupling Subsurface and Above-Surface Models for Optimizing the Design of Borefields and District Heating and Cooling Systems

Accurate dynamic energy simulation is important for the design and sizing of district heating and cooling systems with geothermal heat exchange for seasonal energy storage. Current modeling approaches in building and district energy simulation tools typically consider heat conduction through the ground between boreholes without flowing groundwater. While detailed simulation tools for subsurface heat and mass transfer exist, these fall short in simulating above-surface energy systems. To support the design and operation of such systems, the study developed a coupled model including a software package for building and district energy simulation, and software for detailed heat and mass transfer in the subsurface. For the first, it uses the open-source Modelica Buildings Library, which includes dynamic simulation models for building and district energy and control systems. For the heat and mass transfer in the soil, it uses the TOUGH simulator. The TOUGH family of codes can model heat and multi-phase, multi-component mass transport for a variety of fluid systems, as well as chemical reactions, in fractured porous media. The study validated the coupled modeling approach by comparing the simulation results with one from the g-function based ground response model. It then looked into effects when the water table and the regional groundwater flow are considered in the ground, from the perspective of heat exchange between borehole and ground, and the electrical consumption of the district heating and cooling systems. To access the simulation models, please find the links in the submission: -- For coupled approach validation: see model Buildings.Fluid.Geothermal.Borefields.Examples.BorefieldsWithTough and Buildings.Examples.DistrictReservoirNetworks.Examples.Reservoir3Variable_TOUGH from the "Modelica Building Library" resource, branch issue1495_tough_interface, commit a2667c0. -- For the study of the effect of water table: see model Buildings.Examples.DistrictReservoirNetworks.Examples.Reservoir3Variable_TOUGH from he "Modelica Building Library" resource, branch issue1495_tough_interface_moreIO, commit 760de49. -- For the study of the effect of regional groundwater flow: see Buildings.Examples.DistrictReservoirNetworks.Examples.Reservoir3Variable_TOUGH from he "Modelica Building Library" resource, branch issue1495_tough_interface_moreIO_3D, commit c2a2d2a. The coupling interface script "GrounResponse.py" can be found from the above links in the folder Buildings/Resources/Python-Sources. Also, the needed files for TOUGH simulation are in the folder Buildings/Resources/Python-Sources/ToughFiles that can be accessed through the above links. A brief description of these files is given below; detailed specifications for the first three files may be found in the TOUGH3 Users Guide (Jung et al., 2018) https://tough.lbl.gov/documentation/tough-manuals/. (1) INCON - initial conditions for each grid block (2) INFILE - main input file with material properties and control parameters (3) MESH - description of the computational grid (4) readsave - Modelica/TOUGH interface program: read the final output of TOUGH simulation after TOUGH time step and prepare for transfer to Modelica for next Modelica time step (5) readsave.inp - input parameters for program readsave (6) writeincon - Modelica/TOUGH interface program: write the output of Modelica after Modelica time step and prepare for transfer to TOUGH as initial conditions for the next TOUGH step (7) writeincon.inp - input parameters for program writeincon

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Operating Hardware Impact on the Heat Transfer Properties of Windows

Despite significant advancements in fenestration technology in the last two decades, the thermal transmittance of fenestration products is still significantly higher than that of walls. This corresponds to 60% of the total energy loss of a modern building envelope through the windows. Hence, further development and improvements of fenestration products are necessary. Increasingly stringent codes and standards for fenestration stimulate industry to work on improved solutions. Thus, it is crucial that assessment techniques are able to account for innovations accurately. The thermal effects of non-continuous hardware in window frames are currently ignored by international rating procedures. A preliminary investigation conducted by our team showed significant performance degradation in two of the three out-opening casement profiles caused by the presence of operating hardware. Frames with the structure made of vinyl and fiberglass consist of many air cavities that are penetrated by operating hardware made of highly conductive materials. In these frames, in order to have an accurate assessment, it may be required to employ three-dimensional modeling due to the convective nature of heat transfer within the cavities. However, in this study, we demonstrate that the three-dimensional (3D) effects of non-continuous hardware can be approximated accurately with simpler two-dimensional (2D) simulations. We then develop a simplified model based on weighted average capable of replacing the time- and computation-intensive 3D simulations with 2D simulations and validate it against market available frames and their corresponding hardware. Validation results show that our approximation technique results in discrepancies lower than 0.05 W/(m2K), or 3% of the total thermal transmittance. Thus, we conclude that simplified 2D simulation models may be used for predicting hardware impact in window frames with reasonable accuracy. As windows and glazing structures are becoming ever better thermally insulated, it is becoming even more important to be able to model the impact of the operating hardware on the total thermal performance in order to design the best windows possible and not let the operating hardware ruin an otherwise well-proven design, which is hence addressed in this study.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗