Search NASA⌕ Search

SEARCH · Search NASA

Results for “Data engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

The International Heat Pipe Experiment

On October 4, 1974, the International Heat Pipe Experiment was launched aboard a Black Brant sounding rocket from White Sands, New Mexico. The flight provided six min of near zero gravity during which a total of ten separate heat pipe experiments was performed. The fifteen heat pipes tested represent some of the latest American and European technology. This flight provided the first reported zero gravity data on cryogenic and flat plate vapor chamber heat pipes. Additionally, valuable design and engineering data were obtained on several other heat pipe configurations. The payload and several of its experiments are discussed.

Mcintosh, R.↗

Engine induced structural-borne noise in a general aviation aircraft

This paper describes a study of engine induced structural-borne noise in a single engine light aircraft. Cabin noise and fuselage vibration levels were recorded during ground tests for engine-attached, engine-detached, interior-installed, and interior-removed configurations. By comparisons of the data, engine induced structure-borne noise is shown to be a primary source of cabin noise. Corresponding fuselage vibration levels were quite high with energy concentrated mainly in the lower frequencies. A measure of the noise control effectiveness of the interior trim was also obtained.

Unruh, J. F.↗

LITE data processing

The Lidar In-space Technology Experiment (LITE) was a payload onboard the Space Shuttle Discovery as part of the September 1994 STS-64 mission. LITE successfully made both atmospheric and surface measurements at the 355 nm, 532 nm, and 1064 nm wavelengths [Winker et al., 1996]. At mission completion, nearly 45 Gbytes of data had been obtained. As the data were collected they were organized into three data sets. The largest of these data sets contained the single-shot full resolution digitized lidar signals for all three wavelengths. The other two data sets contained the instrument status data block (ISDB) and the quick look science data (QLSD). ISDB information was generated once per second and contained timing parameters and engineering data related to the health, status, and configuration of the instrument. The QLSD are 100shot averages of the 355 nm and 532 nm lidar signals and were generated at ten second intervals. As the LITE data were generated, they were output to low-rate and high-rate telemetry streams. The low-rate data contained the ISDB and QLSD. The lowrate data were transmitted to the ground by the Shuttle S-band system through the Tracking and Data Relay Satellite System (TDRSS). The high-rate data contained the full resolution digitized lidar signals for all three wavelengths, the ISDB, and QLSD. The high-rate data were transmitted in real time by the Ku-band system through TDRSS downlink to the LITE operations center at the Johnson Space Center (JSC). High-rate data were only obtained when the orbiter and TDRSS telemetry link coincided with the real-time operations of LITE. The low-rate data were backed up by a Shuttle recorder during periods when the telemetry link was unavailable, and the entire lowrate data stream was transferred to the ground over the course of the mission. A total of 53 hours of lowrate data and 45.5 hours of high-rate data were acquired. All of the LITE raw telemetry data have been archived at the NASA Langley Research Center (LaRC), and the LITE high-rate data have been processed to the level 1 data product. This paper describes the data processing steps required to convert the LITE raw, high-rate telemetry data to the LITE level 1 data product.

Powell, Kathleen A.↗

Program Analyzes Radar Altimeter Data

A computer program has been written to perform several analyses of radar altimeter data. The program was designed to improve on previous methods of analysis of altimeter engineering data by (1) facilitating and accelerating the analysis of large amounts of data in a more direct manner and (2) improving the ability to estimate performance of radar-altimeter instrumentation and provide data corrections. The data in question are openly available to the international scientific community and can be downloaded from anonymous file-transfer- protocol (FTP) locations that are accessible via links from altimetry Web sites. The software estimates noise in range measurements, estimates corrections for electromagnetic bias, and performs statistical analyses on various parameters for comparison of different altimeters. Whereas prior techniques used to perform similar analyses of altimeter range noise require comparison of data from repetitions of satellite ground tracks, the present software uses a high-pass filtering technique to obtain similar results from single satellite passes. Elimination of the requirement for repeat-track analysis facilitates the analysis of large amounts of satellite data to assess subtle variations in range noise.

Vandemark, Doug↗

An Investigation of State-Space Model Fidelity for SSME Data

In previous studies, a variety of unsupervised anomaly detection techniques for anomaly detection were applied to SSME (Space Shuttle Main Engine) data. The observed results indicated that the identification of certain anomalies were specific to the algorithmic method under consideration. This is the reason why one of the follow-on goals of these previous investigations was to build an architecture to support the best capabilities of all algorithms. We appeal to that goal here by investigating a cascade, serial architecture for the best performing and most suitable candidates from previous studies. As a precursor to a formal ROC (Receiver Operating Characteristic) curve analysis for validation of resulting anomaly detection algorithms, our primary focus here is to investigate the model fidelity as measured by variants of the AIC (Akaike Information Criterion) for state-space based models. We show that placing constraints on a state-space model during or after the training of the model introduces a modest level of suboptimality. Furthermore, we compare the fidelity of all candidate models including those embodying the cascade, serial architecture. We make recommendations on the most suitable candidates for application to subsequent anomaly detection studies as measured by AIC-based criteria.

Martin, Rodney Alexander↗

On Certain Theoretical Developments Underlying the Hilbert-Huang Transform

One of the main traditional tools used in scientific and engineering data spectral analysis is the Fourier Integral Transform and its high performance digital equivalent - the Fast Fourier Transform (FFT). Both carry strong a-priori assumptions about the source data, such as being linear and stationary, and of satisfying the Dirichlet conditions. A recent development at the National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC), known as the Hilbert-Huang Transform (HHT), proposes a novel approach to the solution for the nonlinear class of spectral analysis problems. Using a-posteriori data processing based on the Empirical Mode Decomposition (EMD) sifting process (algorithm), followed by the normalized Hilbert Transform of the decomposed data, the HHT allows spectral analysis of nonlinear and nonstationary data. The EMD sifting process results in a non-constrained decomposition of a source real-value data vector into a finite set of Intrinsic Mode Functions (IMF). These functions form a nearly orthogonal derived from the data (adaptive) basis. The IMFs can be further analyzed for spectrum content by using the classical Hilbert Transform. A new engineering spectral analysis tool using HHT has been developed at NASA GSFC, the HHT Data Processing System (HHT-DPS). As the HHT-DPS has been successfully used and commercialized, new applications pose additional questions about the theoretical basis behind the HHT and EMD algorithms. Why is the fastest changing component of a composite signal being sifted out first in the EMD sifting process? Why does the EMD sifting process seemingly converge and why does it converge rapidly? Does an IMF have a distinctive structure? Why are the IMFs nearly orthogonal? We address these questions and develop the initial theoretical background for the HHT. This will contribute to the development of new HHT processing options, such as real-time and 2-D processing using Field Programmable Gate Array (FPGA) computational resources,

Kizhner, Semion↗

Preliminary summary of the ETF conceptual studies

Power plant studies have shown the attractiveness of MHD topped steam power plants for baseload utility applications. To realize these advantages, a three-phase development program was initiated. In the first phase, the engineering data and experience were developed for the design and construction of a pilot plant, the Engineering Test Facility (ETF). Results of the ETF studies are reviewed. These three parallel independent studies were conducted by industrial teams led by the AVCO Everett Research Laboratory, the General Electric Corporation, and the Westinghouse Corporation. A preliminary analysis and the status of the critical evaluation of these results are presented.

Seikel, G. R.↗

Special Report on the Data Collection Programs for the Ground Based Nitrogen Washout Experiment. Volume 2 - Detailed Program Descriptions, Listings, Examples and Hardware Specifications

Personal data input, decompression data, nitrogen washout, nitrogen data, and update computer programs are described. Input data and formats; program output, reports, and data; program flowcharts; program listings; sample runs with input and output pages; hardware operation; and engineering data are provided.

Source record↗

The Mars Science Laboratory (MSL) Entry, Descent And Landing Instrumentation (MEDLI): Hardware Performance and Data Reconstruction

The Mars Science Laboratory (MSL) Entry, Descent and Landing Instrumentation (MEDLI) hardware was a first-of-its-kind sensor system that gathered temperature and pressure readings on the MSL heatshield during Mars entry on August 6, 2012. MEDLI began as challenging instrumentation problem, and has been a model of collaboration across multiple NASA organizations. After the culmination of almost 6 years of effort, the sensors performed extremely well, collecting data from before atmospheric interface through parachute deploy. This paper will summarize the history of the MEDLI project and hardware development, including key lessons learned that can apply to future instrumentation efforts. MEDLI returned an unprecedented amount of high-quality engineering data from a Mars entry vehicle. We will present the performance of the 3 sensor types: pressure, temperature, and isotherm tracking, as well as the performance of the custom-built sensor support electronics. A key component throughout the MEDLI project has been the ground testing and analysis effort required to understand the returned flight data. Although data analysis is ongoing through 2013, this paper will reveal some of the early findings on the aerothermodynamic environment that MSL encountered at Mars, the response of the heatshield material to that heating environment, and the aerodynamic performance of the entry vehicle. The MEDLI data results promise to challenge our engineering assumptions and revolutionize the way we account for margins in entry vehicle design.

Little, Alan↗

Integrating computer programs for engineering analysis and design

The design of a third-generation system for integrating computer programs for engineering and design has been developed for the Aerospace Vehicle Interactive Design (AVID) system. This system consists of an engineering data management system, program interface software, a user interface, and a geometry system. A relational information system (ARIS) was developed specifically for the computer-aided engineering system. It is used for a repository of design data that are communicated between analysis programs, for a dictionary that describes these design data, for a directory that describes the analysis programs, and for other system functions. A method is described for interfacing independent analysis programs into a loosely-coupled design system. This method emphasizes an interactive extension of analysis techniques and manipulation of design data. Also, integrity mechanisms exist to maintain database correctness for multidisciplinary design tasks by an individual or a team of specialists. Finally, a prototype user interface program has been developed to aid in system utilization.

Wilhite, A. W.↗

End-to-end deep learning pipeline for real-time Bragg peak segmentation: from training to large-scale deployment

X-ray crystallography reconstruction, which transforms discrete X-ray diffraction patterns into three-dimensional molecular structures, relies critically on accurate Bragg peak finding for structure determination. As X-ray free electron laser (XFEL) facilities advance toward MHz data rates (1 million images per second), traditional peak finding algorithms that require manual parameter tuning or exhaustive grid searches across multiple experiments become increasingly impractical. While deep learning approaches offer promising solutions, their deployment in high-throughput environments presents significant challenges in automated dataset labeling, model scalability, edge deployment efficiency, and distributed inference capabilities. We present an end-to-end deep learning pipeline with three key components: (1) a data engine that combines traditional algorithms with our peak matching algorithm to generate high-quality training data at scale, (2) a modular architecture that scales from a few million to hundreds of million parameters, enabling us to train large expert-level models offline while deploying smaller, distilled models at the edge, and (3) a decoupled producer-consumer architecture that separates specialized data source layer from model inference, enabling flexible deployment across diverse computing environments. Using this integrated approach, our pipeline achieves accuracy comparable to traditional methods tuned by human experts while eliminating the need for experiment-specific parameter tuning. Although current throughput requires optimization for MHz facilities, our system's scalable architecture and demonstrated model compression capabilities provide a foundation for future high-throughput XFEL deployments.

Wang, Cong↗

Pansophy data as used to develop metrics and evaluate trends across SRF projects and facilities to further quality improvement initiatives

Pansophy, a JLAB SRF engineering data management system (EDMS), is composed of a collection of technolo-gies that together provide for the collection, management and analysis of data for the production and testing of cavities and cryomodules. From its inception in 2000, when data collection was a priority for such projects as SNS, CEBAF 12GeV upgrade, LCLS-II, and in the future the SNS-PPU, the focus has turned to data analysis and reporting on quality metrics and key performance indica-tors (KPIs). Reporting enhancements include monthly quality metrics, project specific KPIs, and trending across projects. With the use of Pareto Charts to help analyze vendor quality and non-conformance, timelines of pro-ject and facility metrics, project managers and subject matter experts (SME) are able to look for trends and pre-pare further quality improvement initiatives for their projects.

McDonald, M. G.↗

External Insulation of Masonry Walls and Wood Framed Walls

The use of exterior insulation on a building is an accepted and effective means to increase the overall thermal resistance of the assembly that also has other advantages of improved water management and often increased air tightness of building assemblies. For thin layers of insulation (1” to 1 ½”), the cladding can typically be attached directly through the insulation back to the structure. For thicker insulation layers, furring strips have been added as a cladding attachment location. This approach has been used in the past on numerous Building America test homes and communities (both new and retrofit applications), and has been proven to be an effective and durable means to provide cladding attachment. However, the lack of engineering data has been a problem for many designers, contractors, and code officials. This research project developed baseline engineering analysis to support the installation of thick layers of exterior insulation on existing masonry and frame walls. Furthermore, water management details necessary to integrate windows, doors, decks, balconies and roofs were created to provide guidance on the integration of exterior insulation strategies with other enclosure elements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Effect of Correlation on Multi-Engine Rocket Propulsion Systems

A matter of great concern in the design and operation of multi-engine rocket propulsion systems is the effect of the premature shutdown of one engine on the vehicle. This probability that a premature shutdown will cause a vehicle loss is termed correlation. Based on airbreathing experiences as well as rocket engine data the best estimate of this correlation is made and then applied to the overall multi-engine reliability problem to demonstrate its potential effect. At this point, follow-on analyses are pointed out that illustrate how any potential failures that may cause a correlatable event can be eliminated; thus bringing this correlation to almost 0.

Baker, J. R.↗

Project Galileo: completing Europa, preparing for Io

Galileo has completed the Europa leg of the Galileo Europa Mission, and is now pumping down the apojove in each succeeding orbit in preparation for the Io phase. Including three encounters earlier in the primary mission, the total of ten close passes by Europa have provided a wealth of interesting and provocative information about this intriguing body. The results presented include new and exciting information about Europa's interactions with Jupiter's magnetosphere, its interior structure, and its tantalizing surface features, which strongly hint at a watery subsurface layer. Additional data concerning Callisto, and its own outlook for a subsurface ocean are also presented. In addition the engineering aspects of operating the spacecraft during the past year are explored, as well as a brief examination of what will be the challenges to prepare for the Io encounters. The steadily increasing radiation dosage that the spacecraft is experiencing is well beyond the original design parameters, and is contributing to a number of spacecraft problems and concerns. The ability of the flight team to analyze and solve these problems, even at the reduced staffing levels of an extended mission, is a testament to their tenacity and loyalty to the mission. The engineering data being generated by these continuing radiation-induced anomalies will prove invaluable to designers of future spacecraft to Jupiter and its satellites. The lessons learned during this arduous process are presented. c 2000 International Astronautical Federation. Published by Elsevier Science Ltd. All rights reserved.

long duration↗

Automated cataloging and characterization of space-derived data

One of the most significant technical issues that NASA must address and resolve is the problem of managing the enormous amounts of scientific and engineering data that will be generated by the next generation of remote sensing systems such as the Hubble Space Telescope (HST) and the Earth Observing System (EOS). The amount of data these sensors are expected to produce will be orders of magnitude greater than NASA has ever experienced. Consequently new solutions must be developed for managing, accessing, and automatically inputting the data into a database in some expressive fashion that will provide a meaningful understanding and effective utilization of this data in a multidisciplinary environment. Presently, scientific data provided by satellites and other sources are processed, cataloged, and archived according to narrow mission or project-specific requirements with little regard to the semantics of the overall research. Scientists therefore lack knowledge of or access to potentially valuable data outside their own field. What is needed is an innovative approach that will allow collected data to be automatically cataloged, characterized, and managed in a domain-community. A concept and design approach that employs expert system-based knowledge controllers combined with advanced spatial database systems and graphical data structures is discussed.

Campbell, William J.↗

Automated cataloging and characterization of space-derived data

One of the most significant technical issues that NASA must address and resolve is the problem of managing the enormous amounts of scientific and engineering data that will be generated by the next generation of remote sensing systems such as the Hubble Space Telescope (HST) and the Earth Observing System (EOS). The amount of data these sensors are expected to produce will be orders of magnitude greater than NASA has ever experienced. Consequently, new solutions must be developed for managing, accessing, and automatically inputting the data into a database in some expressive fashion that will provide a meaningful understanding and effective utilization of this data in a multidisciplinary environment. Presently, scientific data provided by satellites and other sources are processed, cataloged, and archived according to narrow mission or project-specific requirements with little regard to the semantics of the overall research. Scientists therefore lack knowledge of or access to potentially valuable data outside their own field. What is needed is an innovative approach that will allow collected data to be automatically cataloged, characterized, and managed in a domain-community. A concept and design approach that employs expert system-based knowledge controllers combined with advanced spatial database systems and graphical data structures is discussed.

Campbell, William J.↗

Glenn's Telescience Support Center Provided Around-the-Clock Operations Support for Space Experiments on the International Space Station

NASA Glenn Research Center s Telescience Support Center (TSC) allows researchers on Earth to operate experiments onboard the International Space Station (ISS) and the space shuttles. NASA s continuing investment in the required software, systems, and networks provides distributed ISS ground operations that enable payload developers and scientists to monitor and control their experiments from the Glenn TSC. The quality of scientific and engineering data is enhanced while the long-term operational costs of experiments are reduced because principal investigators and engineering teams can operate their payloads from their home institutions.

Malarik, Diane C.↗