Search NASA⌕ Search

SEARCH · Search NASA

Results for “F LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Controlling forebody asymmetries in flight: Experience with boundary layer transition strips

The NASA Dryden Flight Research Center has an ongoing program to investigate aircraft flight characteristics at high angles of attack. As part of this investigation, longitudinal boundary layer transition strips were installed on the F-18 HARV forebody, a preproduction F/A-18 radome with a nose-slice tendency, and the X-31 aircraft forebody and noseboom to reduce asymmetric yawing moments at high angles of attack. The transition strips were effective on the F-18 HARV at angles of attack above 60 deg. On the preproduction F/A-18 radome at an angle of attack near 50 deg the strips were not effective. When the transition strips were installed on the X-31 noseboom, a favorable effect was observed on the yawing moment dynamics but the magnitude of the yawing moment was not decreased.

David F Fisher↗
NASA NTRS2004

Thermodynamic Vent System Test in a Low Earth Orbit Simulation

A thermodynamic vent system for a cryogenic nitrogen tank was tested in a vacuum chamber simulating oxygen storage in low earth orbit. The nitrogen tank was surrounded by a cryo-shroud at -40 F. The tank was insulated with two layers of multi-layer insulation. Heat transfer into cryogenic tanks causes phase change and increases tank pressure which must be controlled. A thermodynamic vent system was used to control pressure as the location of vapor is unknown in low gravity and direct venting would be wasteful. The thermodynamic vent system consists of a Joule-Thomson valve and heat exchanger installed on the inlet side of the tank mixer-pump. The combination is used to extract thermal energy from the tank fluid, reducing temperature and ullage pressure. The system was sized so that the tank mixer-pump operated a small fraction of the time to limit motor heating. Initially the mixer used sub-cooled liquid to cool the liquid-vapor interface inducing condensation and pressure reduction. Later, the thermodynamic vent system was used. Pressure cycles were performed until steady-state operation was demonstrated. Three test runs were conducted at tank fills of 97, 80, and 63 percent. Each test was begun with a boil-off test to determine heat transfer into the tank. The lower tank fills had time averaged vent rates very close to steady-state boil-off rates showing the thermodynamic vent system was nearly as efficient as direct venting in normal gravity.

VanOverbeke, Thomas J.↗
NASA NTRS1992

A kappa-epsilon calculation of transitional boundary layers

A recently proposed kappa-epsilon model for low Reynolds number turbulent flows was modified by introducing a new damping function f(sub mu). The modified model is used to calculate the transitional boundary layer over a flat plate with different freestream turbulence levels. It is found that the model could mimic the transitional flow. However, the predicted transition is found to be sensitive to the initial conditions.

Yang, Z.↗
NASA NTRS2023

Experimental Aeroheating Study in NASA LaRC 20-Inch Mach 6 Air Tunnel: Discrete Roughness on BOLT – Test 7071

An experimental study of the effect of discrete roughness (trips) on boundary layer transition was conducted in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel on the BOLT shape. This study was intended to obtain results that could eventually be compared against experimental results from other facilities, as well as from flight. The trip locations for the present study were selected to correspond to those used for the flight vehicle, but the heights of these discrete roughness elements were varied. Infrared thermography was used to obtain images of the effect of these trips on the behavior of the boundary layer. This report is intended as a quick release of experimental results.

hypersonic↗
NASA NTRS2008

Detection and Characterization of Boundary-Layer Transition in Flight at Supersonic Conditions Using Infrared Thermography

Infrared thermography is a powerful tool for investigating fluid mechanics on flight vehicles. (Can be used to visualize and characterize transition, shock impingement, separation etc.). Updated onboard F-15 based system was used to visualize supersonic boundary layer transition test article. (Tollmien-Schlichting and cross-flow dominant flow fields). Digital Recording improves image quality and analysis capability. (Allows accurate quantitative (temperature) measurements, Greater enhancement through image processing allows analysis of smaller scale phenomena).

Banks, Daniel W.↗
NASA NTRS1992

Digital data acquisition and preliminary instrumentation study for the F-16 laminar flow control vehicle

Preliminary studies have shown that maintenance of laminar flow through active boundary-layer control is viable. Current research activity at NASA Langley and NASA Dryden is utilizing the F-16XL-1 research vehicle fitted with a laminar-flow suction glove that is connected to a vacuum manifold in order to create and control laminar flow at supersonic flight speeds. This experimental program has been designed to establish the feasibility of obtaining laminar flow at supersonic speeds with highly swept wing and to provide data for computational fluid dynamics (CFD) code calibration. Flight experiments conducted as supersonic speeds have indicated that it is possible to achieve laminar flow under controlled suction at flight Mach numbers greater than 1. Currently this glove is fitted with a series of pressure belts and flush mounted hot film sensors for the purpose of determining the pressure distributions and the extent of laminar flow region past the stagnation point. The present mode of data acquisition relies on out-dated on board multi-channel FM analogue tape recorder system. At the end of each flight, the analogue data is digitized through a long laborious process and then analyzed. It is proposed to replace this outdated system with an on board state-of-the-art digital data acquisition system capable of a through put rate of up to 1 MegaHertz. The purpose of this study was three-fold: (1) to develop a simple algorithm for acquiring data via 2 analogue-to-digital convertor boards simultaneously (total of 32 channels); (2) to interface hot-film/wire anemometry instrumentation with a PCAT type computer; and (3) to characterize the frequency response of a flush mounted film sensor. A brief description of each of the above tasks along with recommendations are given.

Ostowari, Cyrus↗
NASA NTRS1972

Additional three-dimensional boundary-layer computations for a finite swept wing

Calculations have been made of the three-dimensional, compressible, turbulent boundary layer on the finite supercritical wing of the NASA modified F-8 transonic research airplane. The calculations were based on the wing pressure distribution measured in flight at M = 0.90, instead of on wind tunnel data at M = 0.50 and 0.99. Data on the boundary-layer thickness, displacement thickness, skin-friction components, and integrated streamwise skin friction are presented for points along the streamwise stations at which pressure measurements were made.

Nash, J. F.↗
NASA NTRS1974

Influence of low temperatures of friction and wear

A brief review of studies on low-temperature friction are briefly reviewed. A facility and technique for studying friction both in air and in vacuum at temperatures of +20 and -190 C is described. Results of a wear study of structural steels operating together with chromium steel are presented. It is shown that reduction of the test temperature in vacuum leads in certain cases to marked increase of the wear magnitude and friction coefficient. This is associated not only with the general change of the mechanical properties of the materials but also with the influence of temperature reduction on the hardening and structural formation taking place in the surface layers during friction.

Udovenko, V. F.↗