SEARCH · Search NASA

Results for “FRICTION FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Comparison of predicted and measured low-speed performance of two 51 centimeter-diameter inlets at incidence angle

Theoretical and experimental internal flow characteristics of two 51-cm-diameter inlets are compared. Theoretical flow characteristics along the inlet surface were obtained from an axisymmetric potential flow and boundary layer analysis. The experimental data were obtained from low-speed tests of a high-bypass-ratio turbofan engine simulator. Comparisons between calculated internal surface pressure distributions and experimental data are presented for a free-system velocity of 45 m/sec and for incidence angles from 0 deg to 50 deg. Analysis of boundary layer separation on the inlet lip at incidence angle is the major emphasis of this report. Theoretical boundary layer shape factors, skin friction coefficients, and velocity profiles in the boundary layer are presented, along with the location of the transition region. Theoretical and experimental separation locations are also discussed.

Albers, J. A.↗

NASA NTRS1973

Internal friction of rocks and volatiles on the moon

Internal friction quality factors Q up to 2200 have been observed in a strongly outgassed terrestrial analog of lunar basalt. This was accomplished by successively cycling a bar shaped sample vibrating in its fundamental longitudinal mode at 15 kHz to higher and higher temperatures in a vacuum between 100 and 10 nanotorr. After each cycle, Q measured at room temperature in the vacuum was observed to decrease with time suggesting that gas reabsorption was taking place even at these low pressures. A study of the effect of exposing a sample to a variety of gases and vapors showed that of the volatiles most likely to be present in the lunar environment H2O was by far the most effective in lowering Q.

Tittmann, B. R.↗

NASA NTRS1976

Reduction of acoustic losses by outgassing

Heat treatment procedure at low pressure increases internal-friction quality factor of treated samples. Method can reduce propagation losses in porous ferroelectric ceramics by as much as a factor of 100.

Cirlin, E. H.↗

NASA NTRS1978

Laboratory measurements of p-wave seismic Q on lunar and analog rocks

The longitudinal-wave, internal friction quality factor (Qp) of out-gassed rock subjected to hydrostatic confining pressure was measured by a technique of aerodynamically shaping the sample ends to remove most of the air drag. Q values of about 1000 and 100 were obtained at 100 MPa and in laboratory air, respectively. The temperature dependence of Q in lunar rock 70215.85 and an analog of lunar basalt was investigated over the range -100 to 450 deg C. A systematic increase in Q was observed at 50 Hz, 5 kHz and 50 kHz. When the temperature was lowered to -100 deg C moderate decreases in Q were observed from 100 to 250 deg C, and high Q values were obtained at 450 deg C. The temperature and pressure dependences of Q suggest that high lunar seismic Q values imply a very dry crust to depths of at least 50 km. These results further indicate that elastic waves are damped in volatile-rich rock by an absorption mechanism which involves changes in the bonding, structure and coverage of the molecular, physisorbed and chemisorbed H2O at crack and grain boundaries.

Tittmann, B. R.↗

NASA NTRS1979

Seismic Q and velocity at depth

Measurements of the p-wave and s-wave internal friction quality factors (Q) and velocities of samples of a moderately outgassed terrestrial analog of lunar basalt exposed simultaneously to temperatures and hydrostatic confining pressures in accordance with the best available estimates of the lunar selenotherm are presented. Q values and velocities are found to increase with simulated depth, and an extrapolation of the Q value to a thoroughly outgassed states provides a Q value in reasonable agreement with those derived from lunar seismic data, suggesting a very dry lunar crust. Results also imply that similar seismic determinations for Mars would be able to distinguish between a dry crust and a crust containing water trapped beneath a layer of ice. Results of thermal cracking tests which demonstrate that high degrees of cracking associated with thermal cycling, as during the lunar day, are not inconsistent with high Q in a dry environment are presented, and it is shown that volatiles with diple moments comparable to H2O can greatly affect Q. Possible attenuation mechanisms are then considered, and velocity measurements on a synthetic anorthosite are presented.

Tittmann, B. R.↗

NASA NTRS1992

Effect of fiber orientation on the fracture toughness of brittle matrix composites

The effective fracture toughness of brittle matrix materials can be increased through the addition of short, poorly bonded fibers which bridge the growing crack. The orientation distribution of the fibers is likely to be biased, and not in an ideal random or aligned state. A micromechanical model is formulated for the postcracking behavior using the force-displacement relation for an arbitrary fiber bridging a crack, the fiber orientation density function, and the fiber location density function. This model is then used to determine an effective traction law for the bridging fibers, as well as the steady state bridging toughness increment. In most cases, the results may be placed in the form of a product of the aligned fiber results times a modifying integrated orientation factor. The frictional shear stress on fiber pull-out is allowed to vary during pull-out, modeling the effects of matrix breakdown, fiber surface smoothing or wear debris accumulation. Results are presented for a variety of representative planar and three-dimensional fiber orientation states.

Jain, L. K.↗

NASA NTRS1996

Demonstration of the Feasibility of High Temperature Bearing Lubrication From Carbonaceous Gases

Research has been conducted on silicon nitride pin-on-disk sliding contacts at temperatures of up to 520 C, and four-ball rolling contacts with silicon nitride balls and 52100 steel or silicon nitride races at 590 C. These tests were conducted in a variety of gaseous environments in order to determine the effects of simulated engine exhaust gas on the carbonaceous gas decomposition lubrication scheme. In rolling tests with steel races and exhaust gas the wear track depth was roughly half that of tests run in nitrogen gas alone. The deposition of lubricous microcrystalline graphitic carbon on the rolling surfaces, generated from the carbon monoxide within the exhaust gas mixture, was verified by microfocused Raman spectroscopy. Ten-fold reductions in rolling wear could be achieved by the exhaust gas atmosphere in cases where water vapor was removed or not present. The exhaust gas mixture alone was not found to provide any lubricating effect on silicon nitride sliding contacts, where the rate of wear greatly exceeds the rate of carbon deposition. Directed admixture of acetylene (as low as 5% of the exhaust gas flow rates), has provided reductions in both wear volume and coefficient of friction by factors of 60X and 20X respectively for sliding contacts during the initial 80 m of sliding distance. Exhaust gas atmosphere with the acetylene admixture provided 65OX reductions in steady state wear rate compared to that measured for sliding contacts in dry N2. Such acetylene admixture also augments the ability of the exhaust gas atmosphere to lubricate high-temperature rolling contacts, with up to 25-fold reductions in wear track depth compared to those measured in the presence of N2 alone. In addition to providing some lubricating benefit itself, an important potential role of the exhaust gas from rich mixtures would be to shield bearings from 02. Such shielding enables surface deposition of lubricous pyrolytic carbon from the acetylene admixture, instead of combustion, rendering feasible the continuously replenished solid lubrication of high-temperature bearing surfaces.

Blanchet, Thierry A.↗

NASA NTRSDate not supplied

Packed Bed Reactor Experiment (PBRE)-2: Pressure Drop Measurements in Microgravity

Single and two-phase flow through porous media are encountered on ground and in space in numerous applications related to life support systems, fuel cells, chemical/materials processing and transporting nutrients to plants. These systems operate differently in the microgravity environment encountered in space travel because the density differences no longer cause the phases to separate or “drain” under the body force of gravity. In the absence of gravity, the interfacial or capillary forces play a more significant role in determining the operational variables such as phase distribution, liquid holdup, and pressure drop especially when the liquid inertia and viscous forces are at minimum. Lower liquid flow rates in air-water two-phase flows represent the case for most of the space processes that depend on two-phase flows in porous media. The Packed Bed Reactor Experiment (PBRE) was developed and flown on the International Space Station (ISS) by NASA to extend a series of fundamental studies of gas-liquid flows through porous media. The goal of the this series of flight experiments (PBRE-1 and PBRE-2) is to better understand the hydrodynamics of two phase flows in porous media in flow regimes dominated by inertia and viscous effects and understanding the role of the interfacial forces and their role in determining the flow dynamics. The flight experiments were preceded by a series of low gravity experiments performed on the low gravity aircraft. These experiments led to the development of a semi-empirical two-phase pressure drop and flow pattern transition in support of a number of reactor beds planned for water reclamation processes onboard of the international space station. The PBRE flight experiment was designed to deliver a wide range of tightly controlled gas (nitrogen) and liquid (water) flows to one of two interchangeable test sections differing only in the type of internal packing material. In this paper, we describe the PBRE-2 experiment and present preliminary low gravity data on pressure drop and compare with semi-empirical model pressure drop predictions. This work is supported by the National Aeronautics and Space Administration (NASA) under grant no. 80NSSC20K0830

Suratman Number↗

NASA NTRSDate not supplied

Two-Phase Flow in Filters and Orifices: In preparation for Measurements on ISS Packed Bed Reactor Experiment-Water Recovery Series (PBRE-WRS)

Understanding the hydrodynamics of adiabatic two-phase flows in packed bed reactors offers numerous benefits. It enables the optimization of chemical reactions rates and products, crucial for pharmaceuticals and energy production industries. Additionally, this understanding aids in designing more efficient and compact reactors, reducing space and resource requirements. Insights gained from studying such flows in microgravity contribute to advancements of space technologies and the enhancement of our capabilities for undertaking future long duration safe, and sustainable space exploration missions. The Packed Bed Reactor Experiment-Water Recovery Series (PBRE-WRS) is a flight experiment planned for operation on the Microgravity Science Glove box (MSG) facility of the International Space Station (ISS). The objective of the experiment is to validate hydrodynamic models at a range of gas and liquid flow rates. The microgravity environment allows for measurement and observation of aspects of fluid dynamics that are unique when compared to observations made in full or partial gravity environments. The experiment consists of testing two-phase flow hydrodynamics in three different filters, four (4) orifices and one check valve test articles. The experiment utilizes the hardware of the previously flown PBRE and PBRE-2 with packed beds of different packings materials and sizes. The fluid system of the PBRE-WRS consists of a nitrogen gas delivery and water delivery subsystems. The gas delivery subsystem can accommodate two ranges of gas flow rates, just as for the water delivery system. The nitrogen gas loop is open whereas the water loop is closed. Gas is separated from the water using a gas-liquid phase separator which is located in the water delivery module. Preliminary results from ground testing show the pressure drop increasing at different rates with the liquid and gas flow rates in the Brine filter. In this work, a detailed system description is presented along with a summary of results from ground performance testing of different test sections in an end-to-end preflight testing campaign.

Packed Bed Reactor Experiment↗

NASA NTRSDate not supplied

Flow Boiling and Condensation Experiment Overview

A brief overview of the Flow Boiling and Condensation Experiment will be presented at the Technical Interchange Meeting between NASA-GRC Scientists and Engineers and the Korea Aerospace Research Institute (KARI). The presentation describes the development of the FBCE, its constraints, and the on-going testing that had been and continues to be executed onboard of the International Space Station (ISS).

International Space Station↗

DOE OSTI2016

The effect of pebble friction on pattern of pebble packing - 18371

To study the influence of friction coefficient of fuel pebble on pebble packing structure in the pebble bed type high temperature reactor (HTR), 3D numerical simulation has been carried out. To reveal the packing structure, the packing fraction distribution, contact number distribution and Delaunay/Voronoi based cell volume distributions are investigated. It demonstrates that friction plays a pivotal role in determining the final static packing in pebble beds, and attention should be paid to the change of friction coefficient of pebbles when packing structure is particularly concerned in a pebble bed reactor. Furthermore, by digging out the regular tetrahedrons, it reveals that there are not concentrated regular structures near the wall. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2016

Sic-Sic Composite Interphase Evaluation via Small Scale Mechanical Testing

Silicon carbide (SiC) has emerged as a highly capable engineering material for extreme environment applications. It has proven particularly useful for high temperature applications where it exhibits exceptional strength, relative chemical inertness, and low coefficient of thermal expansion. Recent studies have shown that SiC also has excellent neutronic properties including low thermal neutron absorption, low tritium permeability, and high radiation tolerance. As a result, SiC-SiC composites are being considered for application in accident tolerant fuel cladding and other structural components for fission and fusion reactors. The standard crystalline form of SiC is inherently brittle and therefore subject to low damage tolerance. In order to increase the material toughness, SiC-SiC fiber-matrix composites have been developed. These composites are divided into three constituents; a highly crystalline and near stoichiometric SiC fiber (commonly Hi-Nicalon{sup TM} Type-S or Tyranno{sup TM}-SA), a (layered) interphase of graphitized pyrolytic carbon (PyC) around the fiber, and a chemical vapor infiltrated (CVI) SiC matrix that consolidates the material. Increased toughness is achieved through two primary mechanisms: increasing the crack length by introducing more barriers, and fiber pullout via interphase shear within the matrix. As a result, it has become critically important to understand the fundamental properties of SiC-SiC composites. However, comprehensive material properties are difficult to predict unless we have an in depth knowledge of the individual constituents (fiber, matrix, interphase) and how their properties interact with one another at the micro-scale. Of specific interest to this work are the interfacial properties of the fiber-matrix interface. This includes the internal friction coefficient and interfacial debond shear stress. (authors)

36 MATERIALS SCIENCE↗

NASA NTRS1992

Environmental effects on friction and wear of diamond and diamondlike carbon coatings

Reciprocating sliding friction experiments were conducted with a natural diamond flat, diamond film, and low and high density diamondlike carbon (DLC) films in contact with pin specimens of natural diamond and silicon nitride (Si3N4) both in humid air and dry air nitrogen. The results indicated that for natural diamond pin contacts the diamond films and the natural diamond flat were not susceptible to moisture but that moisture could increase both the coefficient of friction and the wear factors of the DLC films. The coefficients of friction and wear factors of the diamond films were generally similar to those of the natural diamond flat both in humid air and dry air nitrogen. In dry nitrogen the coefficients of friction of the high density DLC films in contact with pin specimens of both diamond and Si3N4 were generally low (about 0.02) and similar to those of the natural diamond flat and the diamond films. The wear factors of the materials in contact with both natural diamond and Si3N4 were generally in the ascending order of natural diamond flat, diamond film, high density DLC film, and low density DLC film. The moisture in the environment increased the coefficients of friction for Si3N4 pins in contact with all the materials. This increase in friction is due to the silicon oxide film produced on the surface of Si3N4 pins in humid air.

Miyoshi, Kazuhisa↗

DOE OSTI2017

Stiffness of frictional contact of dissimilar elastic solids

The classic Sneddon relationship between the normal contact stiffness and the contact size is valid for axisymmetric, frictionless contact, in which the two contacting solids are approximated by elastic half-spaces. Deviation from this result critically affects the accuracy of the load and displacement sensing nanoindentation techniques. This study gives a thorough numerical and analytical investigation of corrections needed to the Sneddon solution when finite Coulomb friction exists between an elastic half-space and a flat-ended rigid punch with circular or noncircular shape. Because of linearity of the Coulomb friction, the correction factor is found to be a function of the friction coefficient, Poisson's ratio, and the contact shape, but independent of the contact size. Two issues are of primary concern in the finite element simulations – adequacy of the mesh near the contact edge and the friction implementation methodology. Although the stick or slip zone sizes are quite different from the penalty or Lagrangian methods, the calculated contact stiffnesses are almost the same and may be considerably larger than those in Sneddon's solution. For circular punch contact, the numerical solutions agree remarkably well with a previous analytical solution. For non-circular punch contact, the results can be represented using the equivalence between the contact problem and bi-material fracture mechanics. Finally, the correction factor is found to be a product of that for the circular contact and a multiplicative factor that depends only on the shape of the punch but not on the friction coefficient or Poisson's ratio.

36 MATERIALS SCIENCE↗

NASA NTRS2005

High Temperature Wear of Advanced Ceramics

It was initially hypothesized that advanced ceramics would exhibit favorable high te- friction and wear properties because of their high hot hardness and low achievable surface roughness welding observed in metals does not occur in ceramics. More recent tribological studies of many nitride, carbide, oxide and composite ceramics, however, have revealed that ceramics often exhibit high friction and wear in non-lubricated, high temperature sliding contacts. A summary is given to measure friction and wear factor coefficients for a variety of ceramics from self mated ceramic pin-on-disk tests at temperatures from 25 to up to 1200 C. Observed steady state friction coefficients range from about 0.5 to 1.0 or above. Wear factor coefficients are also very high and range from about to 10(exp -5) to 10(exp -2) cubic millimeters per N-m. By comparison, oil lubricated steel sliding results in friction coefficients of 0.1 or less and wear factors less than 10(exp -9) cubic millimeters per N-m.

DellaCorte, C.↗

DOE OSTI2018

Lateral bearing capacity of hybrid monopile-friction wheel foundation for offshore wind turbines by centrifuge modelling

The hybrid monopile-friction wheel foundation is an innovative alternative for offshore wind turbines. The concept has wider adaptability and can be used as reinforcement method for existing monopiles. A series of centrifuge tests was performed to investigate the lateral bearing capacities of the hybrid foundation under monotonic loads. Five foundation models and two soil types were considered. According to the recorded responses, the hybrid foundation demonstrated better lateral behaviors that both lateral bearing capacity and stiffness are enhanced. Two analytical methods were proposed and compared with the centrifuge test results. The bearing capacity of the hybrid foundation is smaller than the sum of individual pile and friction wheel, and a reduction factor is suggested for both friction wheels. The friction wheel restrains rotations of monopile and provides extra restoring moments; their effects are idealized as equivalent moments acting on the pile head. The analytical results provide possible solutions in estimating the lateral bearing capacity of the innovative hybrid foundation system for offshore wind turbines by using traditional theories.

17 WIND ENERGY↗

NASA NTRS2004

Oxide Ceramic Films Grown on 55Ni-45Ti for NASA and Department of Defense Applications: Unidirectional Sliding Friction and Wear Evaluation

An investigation was conducted to examine the friction and wear behavior of the two types of oxide ceramic films furnished by the U.S. Army Research Laboratory, Development and Engineering Center (ARDEC) under Space Act Agreement SAA3 567. These two types of oxide ceramics were grown on 55Ni-45Ti (60 wt% Ni and 40 wt% Ti) substrates: one was a TiO2 with no other species (designated the B film) and the other was a TiO2 with additional species (designated the G film). Unidirectional ball-on-disk sliding friction experiments were conducted with the oxide films in contact with sapphire at 296 K (23 C) in approx. 50-percent relative humidity laboratory air in this investigation. All material characterization and sliding friction experiments were conducted at the NASA Glenn Research Center. The results indicate that both films greatly improve the surface characteristics of 55Ni-45Ti, enhancing its tribological characteristics. Both films decreased the coefficient of friction by a factor of 4 and increased wear resistance by a two-figure factor, though the B film was superior to the G film in wear resistance and endurance life. The levels of coefficient of friction and wear resistance of both films in sliding contact with sapphire were acceptable for NASA and Department of Defense tribological applications. The decrease in friction and increase in wear resistance will contribute to longer wear life for parts, lower energy consumption, reduced related breakdowns, decreased maintenance costs, and increased reliability.

Miyoshi, Kazuhisa↗

NASA NTRS1972

Cold-welding test environment

A flight test was conducted and compared with ground test data. Sixteen typical spacecraft material couples were mounted on an experimental research satellite in which a motor intermittently drove the spherical moving specimens across the faces of the fixed flat specimens in an oscillating motion. Friction coefficients were measured over a period of 14-month orbital time. Surface-to-surface sliding was found to be the controlling factor of generating friction in a vacuum environment. Friction appears to be independent of passive vacuum exposure time. Prelaunch and postlaunch tests identical to the flight test were performed in an oil-diffusion-pumped ultrahigh vacuum chamber. Only 50% of the resultant data agreed with the flight data owing to pump oil contamination. Identical ground tests were run in an ultrahigh vacuum facility and a ion-pumped vacuum chamber. The agreement (90%) between data from these tests and flight data established the adequacy of these test environments and facilities.

Wang, J. T.↗