SEARCH · Search NASA

Results for “Flat surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Establishment of a strain analysis capability using photoelastic coatings

In accordance with the Research Plan prepared at the beginning of the Fellowship Program, the summer activities consisted of: training the personnel of the Structural Test Division of the Structures and Dynamics Laboratory in the theory and practice of strain analysis using photoelastic coatings; and performing strain analysis using photoelastic coatings on appropriate test articles. In support of these activities, the following actions were taken: (1) equipment and supplies necessary for strain analysis using photoelastic coatings were specified, purchased, and checked out; (2) four engineers were trained in the theory and practice of strain analysis using photoelastic coatings; (3) four technicians were trained in the practice of preparing and applying photoelastic coatings to both curved and flat surfaces; (4) in addition to the final program seminar, three seminars on the fundamentals and use of photoelastic coatings were presented to a total of 43 members of the various laboratories at MSFC; (5) a photoelastic coating was applied to and used in a test of a thrust vector control corner section; (6) to further assist the engineers with the use and understanding of photoelastic coatings, fifteen journal articles were located and copied, and camera settings for photographic fringe patterns were determined and recorded; and (7) two proposals for providing technical assistance in strain analysis at MSFC and testing of selected components/assemblies at the University of Alabama in Tuscaloosa were written for submission to NASA.

Gambrell, Samuel C., Jr.↗

NASA NTRS1990

A unique high heat flux facility for testing hypersonic engine components

This paper describes the Hot Gas Facility, a unique, reliable, and cost-effective high-heat-flux facility for testing hypersonic engine components developed at the NASA Lewis Research Center. The Hot Gas Facility is capable of providing heat fluxes ranging from 200 Btu/sq ft per sec on flat surfaces up to 8000 Btu/sq ft per sec at a leading edge stagnation point. The usefulness of the Hot Gas Facility for the NASP community was demonstrated by testing hydrogen-cooled structures over a range of temperatures and pressures. Ranges of the Reynolds numbers, Prandtl numbers, enthalpy, and heat fluxes similar to those expected during hypersonic flights were achieved.

Melis, Matthew E.↗

NASA NTRS1990

Numerical study of twin-jet impingement upwash flow

Two horizontally spaced jets impinging normally on a flat surface create a fountain upwash flow due to the collision of the radially flowing wall jets. This fountain flow is of importance to the dynamics and propulsion of STOVL aircraft. The fountain flow influences the lift forces on the aircraft and the ingestion of hot gases and debris by the engine inlet. In this paper, a multigrid based finite-difference numerical procedure has been applied to solve the equations governing this three-dimensional flow. The standard k-epsilon turbulence model has been used. Comparisons with experimental data reveal that while the mean velocities are predicted with reasonable accuracy, the turbulent kinetic energies are seriously in error. The reasons for this discrepancy could be the intense unsteadiness and large-scale structures of the flow in the near-wall region, which cannot be captured well by any Reynolds-averaged turbulence model.

Pegues, W. J.↗

NASA NTRS1991

Evolution and dynamics of shear-layer structures in near-wall turbulence

Near-wall flow structures in turbulent shear flows are analyzed, with particular emphasis on the study of their space-time evolution and connection to turbulence production. The results are obtained from investigation of a database generated from direct numerical simulation of turbulent channel flow at a Reynolds number of 180 based on half-channel width and friction velocity. New light is shed on problems associated with conditional sampling techniques, together with methods to improve these techniques, for use both in physical and numerical experiments. The results clearly indicate that earlier conceptual models of the processes associated with near-wall turbulence production, based on flow visualization and probe measurements need to be modified. For instance, the development of asymmetry in the spanwise direction seems to be an important element in the evolution of near-wall structures in general, and for shear layers in particular. The inhibition of spanwise motion of the near-wall streaky pattern may be the primary reason for the ability of small longitudinal riblets to reduce turbulent skin friction below the value for a flat surface.

Johansson, Arne V.↗

NASA NTRS1991

The climbing crawling robot (a unique cable robot for space and Earth)

Some of the greatest concerns in robotic designs have been the high center of gravity of the robot, the irregular or flat surface that the robot has to work on, the weight of the robot that has to handle heavy weights or use heavy forces, and the ability of the robot to climb straight up in the air. This climbing crawling robot handles these problems well with magnets, suction cups, or actuators. The cables give body to the robot and it performs very similar to a caterpillar. The computer program is simple and inexpensive as is the robot. One of the important features of this system is that the robot can work in pairs or triplets to handle jobs that would be extremely difficult for single robots. The light weight of the robot allows it to handle quite heavy weights. The number of feet give the robot many roots where a simple set of feet would give it trouble.

Kerley, James J.↗

NASA NTRS1992

Boundary-layer receptivity due to a wall suction and control of Tollmien-Schlichting waves

A numerical study of the generation of Tollmien-Schlichting (T-S) waves due to the interaction between a small free-stream disturbance and a small localized suction slot on an otherwise flat surface was carried out using finite difference methods. The nonlinear steady flow is of the viscous-inviscid interactive type while the unsteady disturbed flow is assumed to be governed by the Navier-Stokes equations linearized about this flow. Numerical solutions illustrate the growth or decay of T-S waves generated by the interaction between the free-stream disturbance and the suction slot, depending on the value of the scaled Strouhal number. An important result of this receptivity problem is the numerical determination of the amplitude of the T-S waves and the demonstration of the possible active control of the growth of T-S waves.

Bodonyi, R. J.↗

NASA NTRS1992

Direct numerical simulation of instabilities in parallel flow with spherical roughness elements

Results from a direct numerical simulation of laminar flow over a flat surface with spherical roughness elements using a spectral-element method are given. The numerical simulation approximates roughness as a cellular pattern of identical spheres protruding from a smooth wall. Periodic boundary conditions on the domain's horizontal faces simulate an infinite array of roughness elements extending in the streamwise and spanwise directions, which implies the parallel-flow assumption, and results in a closed domain. A body force, designed to yield the horizontal Blasius velocity in the absence of roughness, sustains the flow. Instabilities above a critical Reynolds number reveal negligible oscillations in the recirculation regions behind each sphere and in the free stream, high-amplitude oscillations in the layer directly above the spheres, and a mean profile with an inflection point near the sphere's crest. The inflection point yields an unstable layer above the roughness (where U''(y) is less than 0) and a stable region within the roughness (where U''(y) is greater than 0). Evidently, the instability begins when the low-momentum or wake region behind an element, being the region most affected by disturbances (purely numerical in this case), goes unstable and moves. In compressible flow with periodic boundaries, this motion sends disturbances to all regions of the domain. In the unstable layer just above the inflection point, the disturbances grow while being carried downstream with a propagation speed equal to the local mean velocity; they do not grow amid the low energy region near the roughness patch. The most amplified disturbance eventually arrives at the next roughness element downstream, perturbing its wake and inducing a global response at a frequency governed by the streamwise spacing between spheres and the mean velocity of the most amplified layer.

Deanna, R. G.↗

NASA NTRS1992

Sublimation rates of carbon monoxide and carbon dioxide from comets at large heliocentric distances

Using a simple model for outgassing from a small flat surface area, the sublimation rates of carbon monoxide and carbon dioxide, two species more volatile than water ice that are known to be present in comets, are calculated for a suddenly activated discrete source on the rotating nucleus. The instantaneous sublimation rate depends upon the comet's heliocentric distance and the Sun's zenith angle at the location of the source. The values are derived for the constants of CO and CO2 in an expression that yields the local rotation-averaged sublimation rate as a function of the comet's spin parameters and the source's cometocentric latitude.

Sekanina, Zdenek↗

NASA NTRS1993

Hypersonic engine component experiments in high heat flux, supersonic flow environment

A major concern in advancing the state-of-the-art technologies for hypersonic vehicles is the development of an aeropropulsion system capable of withstanding the sustained high thermal loads expected during hypersonic flight. Even though progress has been made in the computational understanding of fluid dynamics and the physics/chemistry of high speed flight, there is also a need for experimental facilities capable of providing a high heat flux environment for testing component concepts and verifying/calibrating these analyses. A hydrogen/oxygen rocket engine heat source was developed at the NASA Lewis Research Center as one element in a series of facilities at national laboratories designed to fulfill this need. This 'Hot Gas Facility' is capable of providing heat fluxes up to 450 w/sq cm on flat surfaces and up to 5,000 w/sq cm at the leading edge stagnation point of a strut in a supersonic flow stream. Gas temperatures up to 3050 K can also be attained. Two recent experimental programs conducted in this facility are discussed. The objective of the first experiment is to evaluate the erosion and oxidation characteristics of a coating on a cowl leading edge (or strut leading edge) in a supersonic, high heat flux environment. Macrophotographic data from a coated leading edge model show progressive degradation over several thermal cycles at aerothermal conditions representative of high Mach number flight. The objective of the second experiment is to assess the capability of cooling a porous surface exposed to a high temperature, high velocity flow environment and to provide a heat transfer data base for a design procedure. Experimental results from transpiration cooled surfaces in a supersonic flow environment are presented.

Gladden, Herbert J.↗

NASA NTRS1993

The effects of buoyancy on the critical heat flux in forced convection

The critical heat flux (CHF) in forced convection over a flat surface at relatively low flow velocities has been found, not unexpectedly, to depend upon the orientation of the buoyancy. The CHF for R-113 was measured at various heating surface orientations for test section Reynolds numbers ranging between 3000 and 6500. In this flow range, the buoyancy force acting on the vapor generally dominates over the flow inertia, yet the inertia would still be substantial were gravity to be reduced. In the experiments of this study, the CHF is determined for heating surface orientations ranging from 0 deg to 360 deg, for flow velocities between 4 cm/s and 35 cm/s, and for subcoolings between 2.8 C and 22.2 C. The results presented here demonstrate the strong influence of buoyancy at low flow velocities, which diminishes as the flow velocity and subcooling are increased.

Brusstar, Matthew J.↗

NASA NTRS1993

Shear buckling response of tailored, rectangular, composite plates

The concept of stiffness tailoring for improved shear buckling resistance of rectangular composite plates is investigated analytically. The tailoring involves only the redistribution of the given material with given orientations to create beneficial stiffening patterns across the planform of the plate. The resulting local nonuniformities in thickness and membrane and bending stiffness combine to change the buckling response of the plate. The weight and average membrane shear stiffness are essentially unaffected by the tailoring. Practical limitations on the degree to which the tailoring may be carried out are shown to govern most designs. Improvements in the shear buckling load on the order of 50 percent are shown possible with monolithic tailoring. Tailored sandwich concepts, in which a light-weight core material is added to keep both plate surfaces flat, can produce improvements well over 100 percent in specific buckling loads compared with uniform composite plates.

Biggers, Sherrill B.↗

NASA NTRS1992

Issues related to waveform computations for radar altimeter applications

An algorithm has been developed to model the average return power waveforms available from general radar altimeter systems, such as the Multimode Airborne Radar Altimeter (MARA) system operated at NASA Goddard Space Flight Center - Wallops Flight Facility. The algorithm is based on a convolutional model comprised of three functions: the average flat surface impulse response (FSIR), the radar system point target response (PTR), and the height pdf of the specular points on the sea surface. The FSIR is modified to account for the asymmetric antenna beam used by the MARA system, and then certain properties of this modified SIR are exploited to obtain closed-form expressions that can be rapidly evaluated. An FFT convolution routine is used to further speed up the computations. The result is an algorithm that can be used to study the effects of pointing errors in surface measurements.

Newkirk, Michael H.↗

NASA NTRS1993

Heat Transfer from Radiatively Heated Material in a Low Reynolds Number Microgravity Environment

A mathematical model of the transient three-dimensional heat transfer between a slowly moving ambient gas stream and a thermally thick or thin flat surface heated by external radiation in a microgravity environment is presented. The problem is motivated in part by fire safety issues in spacecraft. The gas phase is represented by variable property convection-diffusion energy and mass conservation equations valid at low Reynolds numbers. The absence of gravity and low Reynolds number together permit the flow to be represented by a self-consistent velocity potential determined by the ambient velocity and the thermal expansion in the gas. The solid exchanges energy with the gas by conduction/convection and with the surroundings by surface absorption and re-emission of radiation. Heat conduction in the solid is assumed to be one dimensional at each point on the surface as a consequence of the limited times (of order of 10 seconds) of interest in these simulations. Despite the apparent simplicity of the model, the results show a complex thermally induced flow near the heated surface. The thermal exchange between the gas and solid produces an outward sourcelike flow upstream of the center of the irradiated area and a sinklike flow downstream. The responses of the temperature fields and the associated flows to changes in the intensity of the external radiation and the ambient velocity are discussed.

Yamashita, H.↗

NASA NTRS1993

Fluid dynamics and convective heat transfer in impinging jets through implementation of a high resolution liquid crystal technique

A combined convective heat transfer and fluid dynamics investigation in a turbulent round jet impinging on a flat surface is presented. The experimental study uses a high resolution liquid crystal technique for the determination of the convective heat transfer coefficients on the impingement plate. The heat transfer experiments are performed using a transient heat transfer method. The mean flow and the character of turbulent flow in the free jet is presented through five hole probe and hot wire measurements, respectively. The flow field character of the region near the impingement plate plays an important role in the amount of convective heat transfer. Detailed surveys obtained from five hole probe and hot wire measurements are provided. An extensive validation of the liquid crystal based heat transfer method against a conventional technique is also presented. After a complete documentation of the mean and turbulent flow field, the convective heat transfer coefficient distributions on the impingement plate are presented. The near wall of the impingement plate and the free jet region is treated separately. The current heat transfer distributions are compared to other studies available from the literature. The present paper contains complete sets of information on the three dimensional mean flow, turbulent velocity fluctuations, and convective heat transfer to the plate. The experiments also prove that the present nonintrusive heat transfer method is highly effective in obtaining high resolution heat transfer maps with a heat transfer coefficient uncertainty of 5.7 percent.

Kim, K.↗

NASA NTRS1952

On Reflection of Shock Waves from Boundary Layers

Measurements are presented at Mach numbers from about 1.3 to 1.5 of reflection characteristics and the relative upstream influence of shock waves impinging on a flat surface with both laminar and turbulent boundary layers. The difference between impulse and step waves is discussed and their interaction with the boundary layer is compared. General considerations on the experimental production of shock waves from wedges and cones and examples of reflection of shock waves from supersonic shear layers are also presented.

Liepmann, H W↗

NASA NTRS1933

Aerodynamic Forces and Moments of a Seaplane on the Water

This report gives the results of wind-tunnel tests with a seaplane model as a contribution to the solution of the aerodynamic problems. In the tests it was assumed that the seaplane rested motionless on the water and was exposed, in various positions with respect to the supposedly flat surface of the water, to a uniform air current 0 to 360 degrees.

Kohler, M↗

NASA NTRS1993

Shallow crustal discontinuities and graben and scarp formation in the Tharsis region of Mars

We recently obtained photoclinometric profiles across all simple grabens and erosional landforms (e.g., troughs, pits, wall-valley heads, and scarps that are bounded above and below by flat surfaces) that occur within Tempe Terra. These data, together with similar data that we obtained for Syria, Sinai, and Lunae Plana and the Alba Patera region, allow regional examination of shallow crust Al discontinuities between latitude 30 deg. S and 50 deg. N and longitude 50 deg. W and 112 deg. W. The profile for each simple graben was used with an appropriate structural model to estimate the depth to the base of the faulted layer. The depths of erosional wall scarps may also indicate the depths of mechanical discontinuities such as a local lithologic or cryospheric boundary. Examination of these data indicates a surprisingly consistent set of shallow crust Al discontinuities for the Tharsis region at depths of 0.4-0.6 km, 1.0-1.4 km, and 2 km; the maximum depth of the features in most study areas appears to be about 4 km. The concentration of values between 0.4 and 0.6 km in most scarp and some faulted-layer depth data is similar to the range in estimated thicknesses of individual exposed Noachian and Hesperian plains units in the Tharsis region. The regional depth data also show two modes near 1 and 2 km in some study areas and a maximum depth near 4 km in most study areas; the faulted-layer depths in excess of 4 km at Alba Patera occur near the summit of the caldera and could be attributed to volcanic loading. Our detailed examination of these depth data includes the following observations: (1) The mode at 1.0-1.4 km depth transcends age and geologic setting in this broad study area; (2) The 2-km mode is most obvious at Alba Patera and moderately well developed at Syria and Sinai Plana, but it is muted at Tempe Terra, which is in the same latitude range as Alba Patera but older; and (3) The 2-km-depth mode is not present in all areas that have features of Amazonian age. We suggest two possible explanations for our observations in the Tharsis region.

Davis, P. A.↗

NASA NTRS1993

Study on the mechanism of liquid phase sintering (M-12)

The objectives were to (1) obtain the data representing the growth rate of solid particles in a liquid matrix without the effect of gravity; and (2) reveal the growth behavior of solid particles during liquid phase sintering using the data obtained. Nickel and tungsten are used as the constituent materials in liquid phase sintering. The properties of the constituent metals are given. When a compact of the mixture of tungsten and nickel powders is heated and kept at 1550 C, nickel melts down but tungsten stays solid. As the density of tungsten is much greater than that of nickel, the sedimentation of tungsten particles occurs in the experiment on Earth. The difference between the experiments on Earth and in space is illustrated. The tungsten particles sink to the bottom and are brought into contact with each other. The resulting pressure at the contact point causes the accelerated dissolution of tungsten. Consequently, flat surfaces are formed at the contact sites. As a result of dissolution and reprecipitation of tungsten, the shape of particles changes to a polygon. This phenomenon is called 'flattening.' An example of flattening of tungsten particles is shown. Thus, the data obtained by the experiment on Earth may not represent the exact growth behavior of the solid particles in a liquid matrix. If the experiments were done in a microgravity environment, the data corresponding to the theoretical growth behavior of solid particles could be achieved.

Kohara, S.↗