Search NASA⌕ Search

SEARCH · Search NASA

Results for “Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Friction damping studies in multiple turbine blade systems by lumped mass method

Analytical studies were conducted on multiple turbine blade systems using the lumped mass method. Each blade was idealized by a two mass-two spring model whose modal values were determined from the known frequencies corresponding to the first two bending modes and the frequency corresponding to the platform lockup condition. Two friction damping models were considered namely, the blade-to-blade and the blade-damper-blade. The equations of motion derived on the basis of these models were solved by a method of harmonic balance, assuming, in effect, that under cyclic excitation the blades will exhibit cyclic response at the same frequency. The solutions for 8 blade, 16 blade, and 4 blade systems were obtained using the computer program BLADE. The levels of damping produced by the two friction damping models were compared and evaluated. The optimal values of the friction force, for which the tip amplitude of the blades had a minimum value, were determined.

Raju, B. B.↗
NASA NTRS1983

Measurement of rolling friction by a damped oscillator

An experimental method for measuring rolling friction is proposed. The method is mechanically simple. It is based on an oscillator in a uniform magnetic field and does not involve any mechanical forces except for the measured friction. The measured pickup voltage is Fourier analyzed and yields the friction spectral response. The proposed experiment is not tailored for a particular case. Instead, various modes of operation, suitable to different experimental conditions, are discussed.

Dayan, M.↗
NASA NTRS1984

Friction behavior of silicon in contact with titanium, nickel, silver and copper

Sliding friction experiments are conducted with the semiconductor silicon in contact with the metals titanium, nickel, copper, and silver. Sliding is on the (111) plane of single-crystal silicon in the 112 crystallographic direction both in dry and lubricated (mineral oil) sliding. The friction coefficient in dry sliding is controlled by adhesion and the surface chemical activity of the metal. The more active the metal the stronger the adhesion and the higher the friction. In lubricated sliding the lubricant absorbs to the surfaces and reduces the importance of metal chemical effects. In lubricated sliding, silicon ceases to behave in a brittle manner and undergoes plastic deformation under load.

Mishina, H.↗
NASA NTRS1983

Forced response of a cantilever beam with a dry friction damper attached. I - Theory. II - Experiment

A theoretical and experimental study of the forced vibration response of a cantilevered beam with Coulomb damping nonlinearity is described. Viscous damping in the beam is neglected. Beam and dry friction damper configurations of interest for applications to turbine blade vibrations are considered. It is shown that the basic phenomena found by Dowell (1983) for a simply supported beam with an attached dry friction damper of specific geometry also apply to a cantilevered beam and a more general representation of the dry friction damper and its associated mass and stiffness.

Dowell, E. H.↗
NASA NTRS1986

Two-Axis, Self-Nulling Skin-Friction Balance

Two-dimensional aerodynamic skin-friction force measured directly. Disk-shaped prototype design has overall dimensions of 1.25 (3.18 centimeters) diameter and 0.5 inch (1.27 centimeters) height. Unique mechanism consisting of two flexural pivoted arms connected in tandem but at right angle with each other designed to impart plane motion needed to sense two-axis flow over sensing element of balance. Sensing element, 0.370 inch (0.940 centimeter) in diameter, attached to end of second arm is servoed by two restoring-force motors orthogonally mounted in plane of airflow. Mechanism allows free plane motion of sensing element with no friction, and balance self-nulled to provide direct plane skin-friction force measurements continuously.

Tcheng, P.↗
NASA NTRS1986

Centaur engine gimbal friction characteristics under simulated thrust load

An investigation was performed to determine the friction characteristics of the engine gimbal system of the Centaur upper stage rocket. Because the Centaur requires low-gain autopilots in order to meet all stability requirements for some configurations, control performance (response to transients and limit-cycle amplitudes) depends highly on these friction characteristics. Forces required to rotate the Centaur engine gimbal system were measured under a simulated thrust load of 66,723 N (15,000 lb) and in an altitude/thermal environment. A series of tests was performed at three test conditions; ambient temperature and pressure, ambient temperature and vacuum, and cryogenic temperature and vacuum. Gimbal rotation was controlled, and tests were performed in which rotation amplitude and frequency were varied by using triangular and sinusoidal waveforms. Test data revealed an elastic characteristic of the gimbal, independent of the input signal, which was evident prior to true gimbal sliding. The torque required to initiate gimbal sliding was found to decrease when both pressure and temperature decreased. Results from the low amplitude and low frequency data are currently being used in mathematically modeling the gimbal friction characteristics for Centaur autopilot performance studies.

Askew, J. W.↗
NASA NTRS1985

Comparison of the contact stress and friction behavior of SiC and ZrO2 materials

Studies were performed to further elucidate the friction and contact-stress characteristics of structural ceramic materials. New data for fully stabilized and partially stabilized zirconia ceramics are compared with prior test results for sintered SiC. The comparison provides further evidence that the high temperature friction characteristics of sintered SiC are strongly influenced by the presence of a viscous surface layer. The results also show that a ceramic material with lower coefficient of friction and higher fracture toughness has increased resistance to strength-reducing surface damage due to contact stress.

Lindberg, L. J.↗
NASA NTRS1986

Recent skin friction techniques for compressible flows

A brief review is given of developments over the last decade in techniques for the measurement of skin friction in compressible airflows. Emphasis is placed on mean measurements beneath turbulent boundary layers in the supersonic and hypersonic flow regimes. Recent improvements in existing techniques such as the skin friction balance, Preston tube, sublayer fence, and heat transfer analogy are discussed. New or potential techniques including optical and acoustic measurements are also treated. Finally, new results are presented on the adaptation of the recently-developed laser interferometer skin friction meter for use in high-speed wind tunnels.

Settles, G. S.↗
NASA NTRS1985

Frequency domain solutions to multi-degree-of-freedom, dry friction damped systems under periodic excitation

The anticipated low damping level in large space structures (LSS) has been a major concern for the designers of these structures. Low damping degrades the free response and complicates the design of shape and attitude controllers for flexible spacecraft. Dry friction damping has been considered as a means of increasing the passive damping of LSS, by placing it in the joints and connecting junctures of structures. However, dry friction is highly nonlinear and, hence, analytical investigations are difficult to perform. Here, a multi-harmonic, frequency domain solution technique is developed and applied to a multi-DOF, dry friction damped system. It is seen that the multi-harmonic method is much more accurate than traditional, one harmonic solution methods. The method also compares well with time integration. Finally, comparisons are made with experimental results.

Ferri, A. A.↗
NASA NTRS1987

The effects of crack surface friction and roughness on crack tip stress fields

A model is presented which can be used to incorporate the effects of friction and tortuosity along crack surfaces through a constitutive law applied to the interface between opposing crack surfaces. The problem of a crack with a saw-tooth surface in an infinite medium subjected to a far-field shear stress is solved and the ratios of Mode-I stress intensity to Mode-II stress intensity are calculated for various coefficients of friction and material properties. The results show that tortuosity and friction lead to an increase in fracture loads and alter the direction of crack propagation.

Ballarini, Roberto↗
NASA NTRS1986

Friction and wear of sintered Alpha SiC sliding against IN-718 alloy at 25 to 800 C in atmospheric air at ambient pressure

The sliding friction and wear of the SiC-nickel based alloy IN-718 couple under line contact test conditions in atmospheric air at a linear velocity of 0.18 m/sec and a load of 6.8 kg (67N) was investigated at temperatures of 25 to 800 C. It was found that the coefficient of friction was 0.6 up to 350 C then decreased to 0.3 at 500 and 800 C. It is suggested that the sharp decrease in the friction in the range of 350 to 550 C is due to the lubrication value of oxidation products. The wear rate reaches a minimum of 1 x 10 to the -10 to 2 x 10 to the -10 cu cm/cm/kg at 400 to 600 C.

Deadmore, Daniel L.↗
NASA NTRS1987

Friction and wear behaviour of ion beam modified ceramics

In the present study, the sliding friction coefficients and wear rates of carbide, oxide, and nitride materials for potential use as sliding seals (ring/liner) were measured under temperature, environmental, velocity, and loading conditions representative of a diesel engine. In addition, silicon nitride and partially stabilized zirconia discs were modified by ion mixing with TiNi, nickel, cobalt and chromium, and subsequently run against carbide pins, with the objective of producing reduced friction via solid lubrication at elevated temperature. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above. However, the coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combinations, by the ion implantation of TiNi or cobalt. This beneficial effect was found to derive from lubricious titanium, nickel, and cobalt oxides.

Lankford, J.↗
NASA NTRS1988

Adhesion, friction and micromechanical properties of ceramics

The adhesion, friction, and micromechanical properties of ceramics, both in monolithic and coating form, are reviewed. Ceramics are examined in contact with themselves, other harder materials, and metals. For the simplicity of discussion, the tribological properties of concern in the processes are separated into two parts. The first part discusses the pull-off force (adhesion) and the shear force required to break the interfacial junctions between contacting surfaces. The role of chemical bonding in adhesion and friction, and the effects of surface contaminant films and temperature on tribological response with respect to adhesion and friction are discussed. The second part deals with abrasion of ceramics. Elastic, plastic, and fracture behavior of ceramics in solid state contact is discussed. The scratch technique of determining the critical load needed to fracture interfacial adhesive bonds of ceramic deposited on substrates is also addressed.

Miyoshi, Kazuhisa↗
NASA NTRS1987

The effects of crack surface friction and roughness on crack tip stress fields

A model is presented which can be used to incorporate the effects of friction and tortuosity along crack surfaces through a constitutive law applied to the interface between opposing crack surfaces. The problem of a crack with a saw-tooth surface in an infinite medium subjected to a far-field shear stress is solved and the ratios of mode I stress intensity to mode II stress intensity are calculated for various coefficients of friction and material properties. The results show that tortuosity and friction lead to an increase in fracture loads and alter the direction of crack propagation.

Ballarini, Roberto↗
NASA NTRS1987

An integrated approach for friction damper design

A procedure is outlined for determining the optimal design of friction dampers for high speed turbomachinery blading. The procedure includes: an integration of bench test results with finite element analysis and a single mode blade model to ensure accuracy of the analytical model and improve reliability of the friction damper design; an extension of the single mode blade model to predict the engine behavior of friction dampers; and a new way of viewing analytical and experimental results to determine optimal design parameters when the levels of excitation and damping in the system are unknown. Analysis and experiments are performed on a test disk in order to demonstrate and verify the accuracy of the design procedure.

Cameron, T. M.↗
NASA NTRS1988

Frequency domain solutions to multi-degree-of-freedom, dry friction damped systems

Dry friction damping has been considered as a means of increasing the passive damping of a variety of systems including large space structures and turbomachinery blades. However, dry friction is highly nonlinear, and hence, analytical investigations are difficult to perform. Here, a multiharmonic, frequency domain solution technique is developed and applied to a multi-degree-of-freedom, dry friction damped system. It is seen that the multiharmonic method is more accurate than traditional, one-harmonic solution methods. The method also compares favorably with time integration. Finally, comparisons are made with experimental results.

Ferri, A. A.↗
NASA NTRS1989

Flight Balance For Skin-Friction Measurements

Skin-friction balance (flight balance) for use in flight on aircraft fuselage incorporates type-one, closed-loop control to make direct skin-friction force measurements. Curved surface element 2 in. (5.08 cm) in diameter used to sense tangential force of airstream passed over it. Linear electromagnetic force motor exerts restoring force that nulls position of sensing element. Applied skin-friction force measured by sensing amount of current through motor necessary to maintain null position. Unit is rugged, accurate, reliable, and easy to operate. Insensitivity of balance to background rectilinear vibrations and ability to sustain large transient loads during takeoffs and landings make it attractive for flight testing.

Tcheng, Ping↗
NASA NTRS1988

A robust control scheme for flexible arms with friction in the joints

A general control scheme to control flexible arms with friction in the joints is proposed in this paper. This scheme presents the advantage of being robust in the sense that it minimizes the effects of the Coulomb friction existing in the motor and the effects of changes in the dynamic friction coefficient. A justification of the robustness properties of the scheme is given in terms of the sensitivity analysis.

Rattan, Kuldip S.↗