Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hot structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Structural Behavior of Monolithic Fuel Plates During Hot Isostatic Pressing and Annealing

This paper presents results of the stress analysis in the monolithic fuel plates during thermal transients performed using COMSOL finite element analysis software. Large difference in the thermal expansion between the U-Mo foil and Al cladding is the main load origin during heating and cooling of the fuel plates. In addition, the mechanical behavior of the plate is affected by the difference in yield points between the foil and the cladding. This is manifested by the plastic deformation and permanent strains in the cladding, and elastic deformation of the foil. The results show existence of the critical temperature points at which the stresses change from compressive to tensile. The paper highlights principal differences in mechanical behavior between monolithic and dispersion fuel plates, underlines the need for mechanical property data, especially for the U-Mo alloys, and discusses the methodology for mechanical analysis of the monolithic plates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The outer atmosphere of Procyon (Alpha CMi F5IV-V) - Evidence of supergranulation or active regions

Observations made with the Einstein X-ray observatory and Exosat have shown Procyon (Alpha CMi) to have a measurable X-ray flux. The flux observed is similar to the upper limits previously reported. The interpretation of the X-ray data in the context of models made previously by Brown and Jordan (1981) based on spectra obtained with the IUE satellite. The X-ray data lead to a higher electron pressure than does the UV spectrum. These results support the conclusion by Brown and Jordan that the UV data cannot be reconciled with a hot corona in a spherically symmetric uniform model. Two types of models are explored; one in which the X-ray emission originates from an isothermal corona but the UV emission is restricted to limited regions of the disk, analogous to solar supergranulation structure; the other in which hot loop structures are embedded in a cool (T(e) of about 300,000 K) corona. Monitoring of Procyon to search for variability is urgently required to distinguish between these models. Some comparisons with the predictions of scaling laws are made. This hot isothermal coronal model agrees quite well with the predictions of Hearn's (1977) minimum flux model.

Jordan, C.↗

Constitutive modeling for isotropic materials

The third and fourth years of a 4-year research program, part of the NASA HOST Program, are described. The program goals were: (1) to develop and validate unified constitutive models for isotropic materials, and (2) to demonstrate their usefulness for structural analysis of hot section components of gas turbine engines. The unified models selected for development and evaluation were those of Bodner-Partom and of Walker. The unified approach for elastic-viscoplastic constitutive equations is a viable method for representing and predicting material response characteristics in the range where strain rate and temperature dependent inelastic deformations are experienced. This conclusion is reached by extensive comparison of model calculations against the experimental results of a test program of two high temperature Ni-base alloys, B1900+Hf and Mar-M247, over a wide temperature range for a variety of deformation and thermal histories including uniaxial, multiaxial, and thermomechanical loading paths. The applicability of the Bodner-Partom and the Walker models for structural applications has been demonstrated by implementing these models into the MARC finite element code and by performing a number of analyses including thermomechanical histories on components of hot sections of gas turbine engines and benchmark notch tensile specimens. The results of the 4-year program have been published in four annual reports. The results of the base program are summarized in this report. The tasks covered include: (1) development of material test procedures, (2) thermal history effects, and (3) verification of the constitutive model for an alternative material.

Chan, K. S.↗

User's Manual and Final Report for Hot-SMAC GUI Development

A new software package called Higher Order Theory-Structural/Micro Analysis Code (HOT-SMAC) has been developed as an effective alternative to the finite element approach for Functionally Graded Material (FGM) modeling. HOT-SMAC is a self-contained package including pre- and post-processing through an intuitive graphical user interface, along with the well-established Higher Order Theory for Functionally Graded Materials (HOTFGM) thermomechanical analysis engine. This document represents a Getting Started/User's Manual for HOT-SMAC and a final report for its development. First, the features of the software are presented in a simple step-by-step example where a HOT-SMAC model representing a functionally graded material is created, mechanical and thermal boundary conditions are applied, the model is analyzed and results are reviewed. In a second step-by-step example, a HOT-SMAC model of an actively cooled metallic channel with ceramic thermal barrier coating is built and analyzed. HOT-SMAC results from this model are compared to recently published results (NASA/TM-2001-210702) for two grid densities. Finally, a prototype integration of HOTSMAC with the commercially available HyperSizer(R) structural analysis and sizing software is presented. In this integration, local strain results from HyperSizer's structural analysis are fed to a detailed HOT-SMAC model of the flange-to-facesheet bond region of a stiffened panel. HOT-SMAC is then used to determine the peak shear and peel (normal) stresses between the facesheet and bonded flange of the panel and determine the "free edge" effects.

Yarrington, Phil↗

Crystallographic Structure of Truncated CCL21 and the Putative Sulfotyrosine-Binding Site

CCL21 chemokine binds the G protein-coupled receptor CCR7, aiding not only in immune response but also in cancer metastasis. Compared with other chemokines, CCL21 has a unique extended unstructured C-terminus that is truncated in some naturally occurring variants. We have determined the X-ray crystallographic structure of a truncated CCL21 (residues 1–79) lacking the extended C-terminus and identified, via two-dimensional nuclear magnetic resonance (NMR), a putative sulfotyrosine-binding site that may recognize such post-translationally modified tyrosine residues on the receptor. Compared to the previously determined NMR structure of full-length CCL21, the crystal structure presents new druggable binding hot spots resulting from an alternative N-loop conformation. In addition, whereas the previous NMR structure did not provide any structural information after residue 70, the C-terminus of the truncated CCL21, ordered up to Ala77 in our crystal structure, is placed near the N-loop and sulfotyrosine-binding site, indicating that the extended C-terminus of full-length CCL21 can interact with this important region for receptor binding. These observations suggest a potential origin for the autoinhibition of CCL21 activity that was recently described. In conclusion, the new crystal structure and binding hot spot analysis have important implications for the function of the CCL21 C-terminus and drug discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SILCC – VII. Gas kinematics and multiphase outflows of the simulated ISM at high gas surface densities

ABSTRACT We present magnetohydrodynamic (MHD) simulations of the star-forming multiphase interstellar medium (ISM) in stratified galactic patches with gas surface densities Σgas = 10, 30, 50, and 100 $\mathrm{M_\odot \, pc^{-2}}$. The silcc project simulation framework accounts for non-equilibrium thermal and chemical processes in the warm and cold ISM. The sink-based star formation and feedback model includes stellar winds, hydrogen-ionizing UV radiation, core-collapse supernovae, and cosmic ray (CR) injection and diffusion. The simulations follow the observed relation between Σgas and the star formation rate surface density ΣSFR. CRs qualitatively change the outflow phase structure. Without CRs, the outflows transition from a two-phase (warm and hot at 1 kpc) to a single-phase (hot at 2 kpc) structure. With CRs, the outflow always has three phases (cold, warm, and hot), dominated in mass by the warm phase. The impact of CRs on mass loading decreases for higher Σgas and the mass loading factors of the CR-supported outflows are of order unity independent of ΣSFR. Similar to observations, vertical velocity dispersions of the warm ionized medium (WIM) and the cold neutral medium (CNM) correlate with the star formation rate as $\sigma _\mathrm{z} \propto \Sigma _\mathrm{SFR}^a$, with a ∼ 0.20. In the absence of stellar feedback, we find no correlation. The velocity dispersion of the WIM is a factor ∼2.2 higher than that of the CNM, in agreement with local observations. For $\Sigma _\mathrm{SFR} \gtrsim 1.5 \times 10^{-2}\, \mathrm{M}_\odot \, \mathrm{yr}^{-1}\, \mathrm{kpc}^{-2}$ the WIM motions become supersonic.

Astronomy & Astrophysics↗

Effects of surface chemistry on hot corrosion life

Baseline burner rig hot corrosion with Udimet 700, Rene' 80; uncoated and with RT21, Codep, or NiCoCrAlY coatings were tested. Test conditions are: 900C, hourly thermal cycling, 0.5 ppm sodium as NaCl in the gas stream, velocity 0.3 Mach. The uncoated alloys exhibited substantial typical sulfidation in the range of 140 to 170 hours. The aluminide coatings show initial visual evidence of hot corrosion at about 400 hours, however, there is no such visual evidence for the NiCoCrAlY coatings. The turbine components show sulfidation. The extent of this distress appeared to be inversely related to the average length of mission which may, reflect greater percentage of operating time near ground level or greater percentage of operation time at takeoff conditions (higher temperatures). In some cases, however, the location of maximum distress did not exhibit the structural features of hot corrosion.

Fryxell, R. E.↗

JUPITER WILL BECOME A HOT JUPITER: CONSEQUENCES OF POST-MAIN-SEQUENCE STELLAR EVOLUTION ON GAS GIANT PLANETS

When the Sun ascends the red giant branch (RGB), its luminosity will increase and all the planets will receive much greater irradiation than they do now. Jupiter, in particular, might end up more highly irradiated than the hot Neptune GJ 436b and, hence, could appropriately be termed a 'hot Jupiter'. When their stars go through the RGB or asymptotic giant branch stages, many of the currently known Jupiter-mass planets in several-AU orbits will receive levels of irradiation comparable to the hot Jupiters, which will transiently increase their atmospheric temperatures to {approx}1000 K or more. Furthermore, massive planets around post-main-sequence stars could accrete a non-negligible amount of material from the enhanced stellar winds, thereby significantly altering their atmospheric chemistry as well as causing a significant accretion luminosity during the epochs of most intense stellar mass loss. Future generations of infrared observatories might be able to probe the thermal and chemical structure of such hot Jupiters' atmospheres. Finally, we argue that, unlike their main-sequence analogs (whose zonal winds are thought to be organized in only a few broad, planetary-scale jets), red-giant hot Jupiters should have multiple, narrow jets of zonal winds and efficient day-night redistribution.

79 ASTRONOMY AND ASTROPHYSICS↗

Processing and characteristics of transparent Gd 3 TaO 7 polycrystalline ceramics

Transparent polycrystalline Gd 3 TaO 7 ceramics were successfully developed. A sol-gel process was used to synthesize Gd 3 TaO 7 powder with a uniform composition and an estimated average particle size of 100 nm. Simultaneous thermal gravimetric analysis and differential thermal analysis (TGA/DTA) was used to identify the decomposition sequence as a function of temperature for the as-synthesized sol-gel powders. Crystallization was confirmed by X-ray diffraction (XRD) and a single phase was achieved by calcining at 1000°C. The calcined powders were hot-pressed at 1400°C to achieve >96% theoretical density with closed pore structure followed by a hot isostatic pressing at 1400°C at 207 MPa to achieve a fully dense structure. Microstructural characterization shows a uniform grain size distribution with an average grain size of about 7 μm. In-line transmission measurements revealed high transparency in the red and infrared. Thermal conductivity was measured to be >1.6 W/mK at room temperature, decreasing to ~1.3 W/mK by 500°C. Dielectric properties remain stable with relative permittivity values just above 200 and loss tangents <0.005 up to 350°C.

36 MATERIALS SCIENCE↗

Dynamically hot galaxies. II - Global stellar populations

The global relationship between the stellar populations and the structural properties of dynamically hot galaxies (DHGs) is investigated using the same sample as was analyzed by Bender et al. (1992), which includes giant ellipticals, low-luminosity ellipticals, compact ellipticals, diffuse dwarf ellipticals, dwarf spheroidals, and bulges. It was found that all DHGs follow a single relationship between global stellar population (represented by Mg2 index or B-V color) and central velocity dispersion sigma(0), and that the Mg2-sigma(0) relation is significantly tighter than the relation between the Mg2 index and absolute luminosity. The relation between central Mg2 index and bulk B-V color was also found to be tight.

Bender, Ralf↗

Large structural, thin-wall castings made of metals subject to hot tearing, and their fabrication

An article, such as a gas turbine engine mixer, is made by providing a mold structure defining a thin-walled, hollow article, and a base metal that is subject to hot tear cracking when cast in a generally equiaxed polycrystalline form, such as Rene' 108 and Mar-M247. The article is fabricated by introducing the molten base metal into the mold structure, and directionally solidifying the base metal in the mold structure to form a directionally oriented structure. The directionally oriented structure may be formed of a single grain or oriented multiple grains.

Smashey, Russell W.↗

FAR-ULTRAVIOLET SPECTRAL IMAGES OF THE ORION-ERIDANUS SUPERBUBBLE REGION

The far-ultraviolet (FUV) continuum and spectral images of C IV and H{sub 2} emission lines for the region of the Orion-Eridanus Superbubble are hereby presented and compared with maps obtained in other wavelengths. While the region shows complex structures, consisting of hot gases and cold dust, a close examination reveals that the FUV emission in this region can be understood reasonably as the result of their interactions. We confirm the origin of most diffuse FUV continuum to be starlight scattered by dust, but we also find that ionized gas contributes 50%-70% of the total FUV intensity in the regions of H{alpha} arcs. We note the bright diffuse FUV continuum in the eastern part of the northern region, which has a lot of dust, and attribute it to a greater abundance of bright, early-type stars in this region than in the west, as the amount of dust itself does not seem to be much different across 'arc A', which separates the two regions. In addition, two P Cygni-type stars are identified in this eastern region and their peculiar spectral profiles around the C IV emission line are manifested in the scattered diffuse spectrum. Besides this, the C IV emission is generally enhanced at the boundaries of the hot X-ray cavities where thin dust regions are located, confirming the thermal interface nature of the origin of this cooling emission line. The morphology of the H{sub 2} emission shows a general correlation with dust extinction features but its intensity peaks are located in thin dust areas, rather than the peak dust regions. Furthermore, H{sub 2} emission is weak in the arc A region even though the arc passes through the center of the dust-rich area. Hence, the H{sub 2} emission and dust features, together with those of X-ray and ion line emissions, show the stratified structure of arc A quite well, again confirming its thermal interface nature.

79 ASTRONOMY AND ASTROPHYSICS↗

Towards Next Generation TATB-based Explosives by Understanding Voids and Microstructure from 10 nm to 1 cm

TATB-based explosives have been investigated on length scales spanning several orders of magnitude, from just under 10 nm to larger than 1 cm. This has been accomplished using a combination of ultra-small angle x-ray scattering (USAXS), ultra-small angle neutron scattering (USANS), and x-ray computed tomography (XRCT). USAXS determines distributions the smallest structures including hot-spot voids from hundreds of nanometers to a few microns, USANS extends this range to about 10 microns, and two variants of XRCT cover sizes from microns to centimeters. Several examples are presented for LX-17, a triaminotrinitrobenzene based plastic bonded explosive using Kel-F 800. As an extension of previous USAXS results, in these proceedings, an alternate binder results in a more uniform microstructure for the PBX, useful towards design of next-generation TATB-based explosives. These data are an important step to understanding microstructural mechanisms that affect the mechanical properties of TATB-based explosives, and provide complete a comprehensive characterization of the structure of LX-17 from nanometers to centimeters that can be used as empirical input to computational models of detonation, and in determining the relationship between voids and microstructure to detonation properties.

36 MATERIALS SCIENCE↗

The Angular Power Spectrum of BATSE 3B Gamma-Ray Bursts

We compute the angular power spectrum C(sub l) from the BATSE 3B catalog of 1122 gamma-ray bursts and find no evidence for clustering on any scale. These constraints bridge the entire range from small scales (which probe source clustering and burst repetition) to the largest scales (which constrain possible anisotropics from the Galactic halo or from nearby cosmological large-scale structures). We develop an analysis technique that takes the angular position errors into account. For specific clustering or repetition models, strong upper limits can be obtained down to scales l approx. equal to 30, corresponding to a couple of degrees on the sky. The minimum-variance burst weighting that we employ is visualized graphically as an all-sky map in which each burst is smeared out by an amount corresponding to its position uncertainty. We also present separate bandpass-filtered sky maps for the quadrupole term and for the multipole ranges l = 3-10 and l = 11-30, so that the fluctuations on different angular scales can be inspected separately for visual features such as localized 'hot spots' or structures aligned with the Galactic plane. These filtered maps reveal no apparent deviations from isotropy.

Tegmark, Max↗

An Investigation of the Rotamers of Butadiene by High-Resolution Infrared Spectroscopy

A wide-ranging investigation of the high-resolution infrared spectrum of 1,3-butadiene was undertaken with the prime objective of finding subbands in the rotational structure attributable to the gauche rotamer, from which information about the molecular structure could be derived. The one band near 750 cm-1, which had previously been assigned to the gauche rotamer, has been shown to be a difference tone for the trans rotamer. Despite careful searching, no subbands attributable to the gauche rotamer have been found. Two weak Q branches at 463.82 and 462.19 cm-1 might arise from the gauche rotamer. The rotational structure, including two hot bands, was analyzed in the C-type band for the v12(au) mode near 525 cm-1 and the Ctype band near 162 cm-1 for the v13(au) mode. A rotational analysis was also done for the A-type band for the v24(bu) band near 300 cm-1. An unsuccessful attempt was made to extend the analysis of the B-type component of the A/B-type band for v17(bu) near 3000 cm-1. With the exception of the two weak Q branches near 460 cm-1, no new evidence for the gauche rotamer was found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Search for FeH in Hot-Jupiter Atmospheres with High-dispersion Spectroscopy

Most of the molecules detected thus far in exoplanet atmospheres, such as water and CO, are present for a large range of pressures and temperatures. In contrast, metal hydrides exist in much more specific regimes of parameter space, and so can be used as probes of atmospheric conditions. Iron hydride (FeH) is a dominant source of opacity in low-mass stars and brown dwarfs, and evidence for its existence in exoplanets has recently been observed at low resolution. We performed a systematic search of archival CARMENES near-infrared data for signatures of FeH during transits of 12 exoplanets. These planets span a large range of equilibrium temperatures (600 ≲ T eq ≲ 4000 K) and surface gravities (2.5 ≲ logg ≲ 3.5). We did not find a statistically significant FeH signal in any of the atmospheres, but obtained potential low-confidence signals (signal-to-noise ratio ~ 3) in two planets, WASP-33b and MASCARA-2b. Previous modeling of exoplanet atmospheres indicate that the highest volume mixing ratios (VMRs) of 10 -7 to 10 -9 are expected for temperatures between 1800 and 3000 K and log g≳3. The two planets for which we find low-confidence signals are in the regime where strong FeH absorption is expected. We performed injection and recovery tests for each planet and determined that FeH would be detected in every planet for VMRs &NestedGreaterGreater;10 -6 , and could be detected in some planets for VMRs as low as 10 -9.5 . Additional observations are necessary to conclusively detect FeH and assess its role in the temperature structures of hot-Jupiter atmospheres.

79 ASTRONOMY AND ASTROPHYSICS↗

Fine grained fully lamellar structure acquisition and microstructure characteristics of Ti-44Al-4Nb-4V-0.3Mo-Y alloy

Highlights: • Cellular structure is the component of the microstructure of hot forging in α + β two-phase-field. • Inhomogeneous lamellar structure could be eliminated by hot forging in β+γ binary phase field. • After hot forging and annealing at β+γ two-phase-region, fine grained fully-lamellar microstructure is obtained. - Abstract: In this paper, the microstructure characteristic of a β solidifying TiAl alloy Ti-44Al-4Nb-4V-0.3Mo-Y (at. %) was investigated systematically. Cylindrical blanks were isothermal forged at 1250 °C within (α + β) two-phase-field and 1200 °C within (β + γ) two-phase-field under the strain rate of 0.02 s{sup −1} and 0.03 s{sup −1}, with a total reduction of 75%. The microstructure of the alloy forged in α + β two-phase-field consists of lamellar colonies (only represents α{sub 2}/γ lamellar colonies), mixture structure of β/B2 phase and γ phase as well as β/γ lamellae resulted from cellular reaction. However, a large amount of equiaxed γ grains appear with no β/γ lamellae available under forging in β + γ two-phase-field, and the average size of γ grain is about 10 μm. By further annealed at 900 °C for about 0.5 h, the structure of hot forging at 1250 °C is composed of β/B2 phase and equiaxed γ grains with the mean size about 5 μm. After heat treated at 1200 °C for 2 h, the microstructure of this annealed samples is characterized by fine grained fully lamellar (FFL) structure with size of 20 μm. A specially designed hot forging process is proposed, which prevents the existence of inhomogeneous lamellar structure.

36 MATERIALS SCIENCE↗

Hydrothermal synthesis of lutetium disilicate nanoparticles

A simple, low-cost hydrothermal method was developed to synthesize irregular-and rod-shaped lutetium disilicate (Lu{sub 2}Si{sub 2}O{sub 7}) powders with sizes ranging from 71 to 340 nm. The synthesis temperature was 260 Degree-Sign C, which is nearly 1300 Degree-Sign C lower than that required for the solid-state reaction. The results indicated that both the hydrothermal temperature and pH values had great influences on the composition, crystalline phase and morphology of the powders. The formation mechanism, basic thermophysical properties, stability and anticorrosion properties of the Lu{sub 2}Si{sub 2}O{sub 7} powders were also investigated. The obtained powders possessed low thermal conductivity, a suitable thermal expansion coefficient (3.92-5.17 Multiplication-Sign 10{sup -6} K{sup -1}) with the silicon-based substrate and excellent thermal and structural stability. During hot corrosion testing, the surfaces of the samples appeared to react with the water and molten salt vapors, but no serious failure occurred. - Graphical abstract: An image for the as-prepared Lu{sub 2}Si{sub 2}O{sub 7} powders (left) and XRD pattern (right) (inset shows the SEM graph of powders). Highlights: Black-Right-Pointing-Pointer We synthesized Lu{sub 2}Si{sub 2}O{sub 7} powders via a hydrothermal process at 260 Degree-Sign C. Black-Right-Pointing-Pointer Crystalline phase and morphology of the powders changed with experimental parameter. Black-Right-Pointing-Pointer Hot corrosion was determined in an airflow environment containing alkaline vapor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗