Results for “Instability waves” — Page 18

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗

NASA NTRS1994

Effect of nonzero surface admittance on receptivity and stability of compressible boundary layer

The effect of small-amplitude short-scale variations in surface admittance on the acoustic receptivity and stability of two-dimensional compressible boundary layers is examined. In the linearized limit, the two problems are shown to be related both physically and mathematically. This connection between the two problems is used, in conjunction with some previously reported receptivity results, to infer the modification of stability properties due to surface permeability. Numerical calculations are carried out for a self-similar flat-plate boundary layer at subsonic and low supersonic speeds. Variations in mean suction velocity at the perforated admittance surface can also induce receptivity to an acoustic wave. For a subsonic boundary layer, the dependence of admittance-induced receptivity on the acoustic-wave orientation is significantly different from that of the receptivity produced via mean suction variation. The admittance-induced receptivity is generally independent of the angle of acoustic incidence, except in a relatively narrow range of upstream-traveling waves for which the receptivity becomes weaker. However, this range of angles is precisely that for which the suction-induced receptivity tends to be large. At supersonic Mach numbers, the admittance-induced receptivity to slow acoustic models is relatively weaker than that in the case of the fast acoustic modes. We also find that purely real values for the surface admittance tend to have a destabilizing effect on the evolution of an instability wave over a slightly permeable surface. The limits on the validity of the linearized approximation are also assessed in one specific case.

Choudhari, Meelan↗

NASA NTRS1993

On the secondary instability of the most dangerous Goertler vortex

Recent studies have demonstrated the most unstable Goertler vortex mode is found in flows, both two and three-dimensional, with regions of (moderately) large body curvature and these modes reside within a thin layer situated at the base of the conventional boundary layer. Further work concerning the nonlinear development of the most dangerous mode demonstrates that the flow results in a self induced flow reversal. However, prior to the point at which flow reversal is encountered, the total streamwise velocity profile is found to be highly inflectional in nature. Previous work then suggests that the nonlinear vortex state will become unstable to secondary, inviscid, Rayleigh wave instabilities prior to the point of flow reversal. Our concern is with the secondary instability of the nonlinear vortex states, which result from the streamwise evolution of the most unstable Goertler vortex mode, with the aim of determining whether such modes can induce a transition to a fully turbulent state before separation is encountered.

Otto, S. R.↗

NASA NTRS1990

Perpendicular heating of electrons by upper hybrid waves generated by a ring distribution

Satellite observations of electron conical distributions with enhanced fluxes just outside the loss cone suggest that telectrons have been heated perpendicularly to the magnetic field in the mid-altitude polar magnetosphere. To understand electron conical distributions, plasma simulations are conducted to examine an upper hybrid wave instability of a ring electron distribution perpendicular to the magnetic field in a cold electron background. The simulations indicate that both the cold and ring distributions are heated perpendicularly during the saturation stage. From the plasma data, a ring distribution can be identified as a trapped distribution function with an enhancement near 90-deg pitch angle in the phase space density plot. It is suggested that the ring distribution might provide an additional free energy source for generating upper hybrid waves associated with electron conical events.

Lin, C. S.↗

NASA NTRS1980

Broadband jet noise amplification by a pure tone excitation

A model is proposed for the change in turbulent structure of a round jet in the presence of an acoustic excitation. The excitation is initial amplitude at the jet exit. As these waves propagate downstream they extract energy from the mean flow and transfer it to the random turbulence. This results in an increase in the levels of the turbulence and a resulting increase in the radiated broadband noise. An examination is made of the effect of excitation level and frequency on the jet flow. The numerical procedure allows for radial as well as axial variations in the averaged properties of jet to be calculated. The results indicate that the presence of a finite amplitude instability wave increases the spreading of the jet.

Morris, P. J.↗

NASA NTRS1990

Boundary layer receptivity phenomena in three-dimensional and high-speed boundary layers

The process by which the boundary layer internalizes the environmental disturbances in the form of instability waves is known as the boundary-layer receptivity. The paper discusses the importance of receptivity in transition research. The receptivity scenario for three-dimensional and high-speed boundary layers is examined. It is found that, while receptivity mechanisms present in the low-speed case are also operative in these complex flows, certain uniquely 'compressible' receptivity mechanisms may come into play as well. Both numerical, and where convenient, asymptotic procedures are utilized to develop quantitative predictions of the localized generation of a variety of instability types (Tollmien-Schlichting, inflectional, higher modes, crossflow vortices) in boundary layer flows relevant to the National Aero-Space Plane (NASP).

Choudhari, Meelan↗

DOE OSTI2025

Dynamic mode decomposition for gyrokinetic eigenmode analysis

Dynamic mode decomposition (DMD) is a post-processing approach to decompose a complex time series into a set of modes via spectral analysis. DMD provides a new and powerful method to recover gyrokinetic drift-wave eigenfrequencies and eigenfunctions based only on the solution of the gyrokinetic-Maxwell initial value problem with almost no added cost to the initial value solver. In the present paper, DMD is applied to the CGYRO gyrokinetic code using a newly-developed CGYRO-DMD post-processor. CGYRO-DMD is numerically efficient, even on a single CPU. It does not set any restrictions on the plasma shape, beta (ratio of the plasma pressure to the magnetic field pressure), collisionality or number of species, and allows one to resolve numerous eigenmodes, even of comparable growth rates. In addition, DMD is not limited to unstable modes, but rather can capture stable and unstable branches simultaneously. In this work, we illustrate the accuracy of DMD through gyrokinetic analysis of mode transition for electromagnetic drift wave instabilities.

drift-wave eigenmodes↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle of attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane, specifically near both ends of the azimuthal region of a thick boundary layer in the middle, where this region rapidly changes to a thinner boundary layer on either side. At the t = 28.8767 s condition from the ascent part of the anticipated flight trajectory with a flight Mach number of M ∞ = 5.53 and unit Reynolds number of 4.25 x 10 6 /m, either type of departure from the design condition is shown to have a considerable impact on the structure of the basic state rollup within the region of interest and, hence, also on the amplification characteristics of instability waves within the resulting streaks. Yet, for a yaw angle of β = 4 degrees, the computations indicate only a slight reduction with respect to the peak N-factor of nearly 11 at the design condition of zero degrees yaw and zero degrees angle of attack. In contrast, an angle of attack equal to α = 4 degrees, the peak N-factor decreases to nearly 6 on the leeward side and increases above 16 on the windward side, making the onset of transition highly likely on the windward side. Computations also highlight the role of streak instabilities that originate as Mack mode disturbances and also demonstrate the potential pitfalls in using surface pressure sensors alone to gauge the magnitude of instability amplification.

Boundary layer transition↗

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration (Effect of Nonzero AoA and Yaw)

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle of attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane, specifically near both ends of the azimuthal region of a thick boundary layer in the middle, where this region rapidly changes to a thinner boundary layer on either side. At the t = 28.8767 s condition from the ascent part of the anticipated flight trajectory with a flight Mach number of M ∞ = 5.53 and unit Reynolds number of 4.25 x 10 6 /m, either type of departure from the design condition is shown to have a considerable impact on the structure of the basic state rollup within the region of interest and, hence, also on the amplification characteristics of instability waves within the resulting streaks. Yet, for a yaw angle of β = 4 degrees, the computations indicate only a slight reduction with respect to the peak N-factor of nearly 11 at the design condition of zero degrees yaw and zero degrees angle of attack. In contrast, an angle of attack equal to α = 4 degrees, the peak N-factor decreases to nearly 6 on the leeward side and increases above 16 on the windward side, making the onset of transition highly likely on the windward side. Computations also highlight the role of streak instabilities that originate as Mack mode disturbances and also demonstrate the potential pitfalls in using surface pressure sensors alone to gauge the magnitude of instability amplification.

Boundary layer transition↗

DOE OSTI2020

Evidence and modeling of turbulence bifurcation in L-mode confinement transitions on Alcator C-Mod

Analysis and modeling of rotation reversal hysteresis experiments show that a single turbulent bifurcation is responsible for the Linear to Saturated Ohmic Confinement (LOC/SOC) transition and concomitant intrinsic rotation reversal on Alcator C-Mod. Plasmas on either side of the reversal exhibit different toroidal rotation profiles and therefore different turbulence characteristics despite the profiles of density and temperature, which are indistinguishable within measurement uncertainty. Elements of this bifurcation are also shown to persist for auxiliary heated L-modes. The deactivation of subdominant (in the linear growth rate and contribution to heat transport) ion temperature gradient and trapped electron mode instabilities is identified as the only possible change in turbulence within a reduced quasilinear transport model across the reversal, which is consistent with the measured profiles and inferred heat and particle fluxes. Experimental constraints on a possible change from strong to weak turbulence, outside the description of the quasilinear model, are also discussed. These results indicate an explanation for the LOC/SOC transition that provides a mechanism for the hysteresis through the dynamics of subdominant modes and changes in their relative populations and does not involve a change in the most linearly unstable ion-scale drift-wave instability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1993

Roughness-induced generation of crossflow vortices in three-dimensional boundary layers

The receptivity theory of Goldstein and Ruban is extended within the nonasymptotic (quasi-parallel) framework of Zavol'skii et al to predict the roughness-induced generation of stationary and nonstationary instability waves in three-dimensional, incompressible boundary layers. The influence of acoustic-wave orientation, as well as that of different types of roughness geometries, including isolated roughness elements, periodic arrays, and two-dimensional lattices of compact roughness shapes, as well as random, but spatially homogeneous roughness distributions, is examined. The parametric study for the Falkner-Skan-Cooke family of boundary layers supports our earlier conjecture that the initial amplitudes of roughness-induced stationary vortices are likely to be significantly larger than the amplitudes of similarly induced nonstationary vortices in the presence of acoustic disturbances in the free stream. Maximum unsteady receptivity occurs when the acoustic velocity fluctuation is aligned with the wavenumber vector of the unsteady vortex mode. On the other hand, roughness arrays that are oriented somewhere close to the group velocity direction are likely to produce higher instability amplitudes. Limitations of the nonasymptotic theory are discussed, and future work is suggested.

Choudhari, Meelan↗

NASA NTRS2021

Coupling of the FUN3D Unstructured Flow Solver and the LASTRAC Stability Code to Model Transition

We develop an iterative automated method to predict transition locations in boundary-layer flows by using the FUN3D solver to perform flow simulations and the LASTRAC code for linear stability computations. The coupling of FUN3D and LASTRAC allows for a robust physics-based approach to model boundary-layer transition by analyzing the growth of different instability waves and then using that information to iteratively update the resulting transition location. There is no user involvement during the iterative computations. We apply this automated method to subsonic flow over a flat plate with a sharp leading edge. The final solution has regions of laminar and turbulent flow with a transition onset location that agrees with experiments and stability-based correlations. This iterative automated method is also applied to an NLF(1)-0416 airfoil for conditions with and without a separation bubble. Along with predicting transition locations, we compare the streamwise distributions of surface-pressure and skin-friction coefficients to a transport-equation-based model. We consider a 6:1 prolate spheroid at three angles of attack, namely, five, ten, and fifteen degrees, where mixed-mode transition occurs due to both Tollmien-Schlichting and crossflow instabilities. The skin-friction contours and transition fronts at every angle of attack from our iterative automated method show good agreement with past experimental and computational results in the literature for the 6:1 prolate spheroid.

Transition↗

NASA NTRS1986

Eddy processes in the general circulation of the Jovian atmospheres

Two fundamentally different views of the general circulation of Jovian atmospheres have emerged. According to one view, the observed jet streams at the cloud tops are controlled by the vorticity transfers of small scale eddies generated by planetary wave instabilities within a shallow atmospheric layer. According to the alternate point of view, the zonal jets are surface manifestations of deep interior convection organized into cylindrical motion with axes parallel to the planetary rotation axis. Both approaches may be considered in the context of the very different roles assumed by the potential vorticity. A possible reconciliation of the two kinds of dynamical systems is considered in which the interior motion is overlaid with a statically stable cappling layer driven by turbulent energy injection from below. A simple model for the eddy driving of quasi-geostrophic dynamics in the capping layer is presented which is consistent with the tentative evidence for up-gradient momentum flux on Jupiter and IRIS observations of thermal contrast correlations with cyclonic and anticyclonic shear zones. Certain synoptic-scale cloud features in Jupiter's atmosphere are interpreted as breaking waves, which may also influence the lateral mixing of tracers such as the ortho-para hydrogen ratio.

Leovy, Conway↗

NASA NTRS2008

Boundary Layer Receptivity due to Roughness and Freestream Sound for Supersonic Flows over Axisymmetric Cones

The receptivity of supersonic boundary layers due to the interaction of a two-dimensional acoustic wave with a three-dimensional roughness is numerically investigated over a 5-degree sharp tipped straight cone at a free stream Mach number of 3.5 and a high Reynolds number of 10(exp 6)/inch. Both the steady and unsteady solutions are obtained by solving the full Navier-Stokes equations using the fifth-order accurate weighted essentially non-oscillatory (WENO) scheme for spatial discretization and using third-order total-variation-diminishing (TVD) Runge-Kutta scheme for temporal integration. The simulations are performed with different roughness heights and roughness locations. The steady computations with the roughness reveal that the perturbations induced by the roughness remain very close to the wall and do not penetrate to the outer part of the boundary layer. The effects of the roughness persist for about 10 boundary layer thicknesses downstream of each element. The unsteady simulation shows the generation of unstable three-dimensional first mode disturbances within a short distance from the roughness. However, the amplitudes of the instability waves are very small near the neutral point, on the order of 10(exp -4) compared to the free stream disturbances. The receptivity coefficients due to the roughness elements located very close to the tip are one order of magnitude smaller than those due to the roughness elements located closer to the neutral point.

Balakumar, P.↗

NASA NTRSDate not supplied

Large Eddy Simulations of Upper-Ocean Turbulence Across the Equatorial Pacific Cold Tongue

Turbulence in the equatorial Pacific cold tongue plays multiple roles in the sea-surface temperature budget. However, observations of turbulence are limited to a handful of field experiments lasting from a few days to one month at 0 N , 140 W, and the key turbulent fluxes can only be inferred. Although explicit simulations of turbulence resolve these fluxes, the required large eddy simulations (LES) are costly and thus also limited to a few weeks. A two-fold hypothesis motivates this contribution to the PUMP pre-field modelling experiments in support of TPOS: 1) that there exist useful relationships between the surface wind, wave, and buoyancy forcing, oceanic shear and stratification, and turbulent mixing, but 2) these relationships differ between regions of equatorial dynamics (f~0) and higher latitudes, such that the state space is insufficiently sampled to understand these relationships and represent them in ocean general circulation models (OGCM). To address the lack of observations, we simulated 35 continuous days of upper ocean turbulence using LES during October-November 1985 at sites in two regions (70 days in total) of the cold tongue: 0 N, 140 W and 3 N, 140 W. The model reproduces many features of the observed turbulence at 0,140W, including the “deep-cycle” observed by Gregg et al. (1985) Nature and the turbulent pulses every few hours during the night and in the early morning. Furthermore, the results at 3 N support the hypothesis advanced by Cherian et al. (2021) JPO that strong, but intermittent deep-cycle turbulence is observed to the north of the equator in the presence of strong shear associated with Tropical Instability Waves. Comparisons with the K-profile parameterization (KPP) scheme show that additional tuning of the KPP parameters can reduce differences between the turbulent fluxes produced by KPP and LES at both sites. The results will suggest modifications to OGCMs and already emphasize the need for a more extensive measurements of vertical profiles of shear, stratification and turbulent mixing to reveal the spatio-temporal structure of turbulence and how it relates to forcing, shear and stratification across the equatorial Pacific Cold tongue.

Large Eddy Simulations↗

NASA NTRS2019

Disentangling Planets from Photoelectric Instability in Gas-rich Optically Thin Dusty Disks

Structures in circumstellar disks such as gaps and rings are often attributed to planets. This connection has been difficult to show unequivocally, as other processes may also produce these features. In particular, a photoelectric instability (PEI) has been proposed, operating in gas-rich optically thin disks, that generates structures predicted by planet–disk interactions. We examine the question of how to disentangle the planetary effects on disk structure from the effects of the PEI. We use the Pencil Code to perform 2D global hydrodynamical models of the dynamics of gas and dust in a thin disk with and without planetary perturbers. Photoelectric heating is modeled with an equation of state where pressure is proportional to dust surface density. The drag force on grains and its backreaction on the gas are included. Analyzing the situation without PEI, we find that gas–dust interactions alter the shape of the planetary gap from the dust-free case when the local dust-to-gas ratio ε approaches unity. This result also applies to primordial disks, because dust drifting inward accumulates at the edge of the planetary gap, and any initial dust-to-gas ratio eventually achieves ε = 1 if the dust reservoir is sufficient. We find a result particular to high dust-to-gas ratio disks as well: as dust drifts inward, the dust front becomes a sharp transition, and the backreaction triggers the Rossby wave instability. When PEI is included, we find that it obscures structures induced by planets unless the planet's mass is sufficiently large to carve a noticeable gap. Specifically, the instability generates arcs and rings of regular spacing: a planet is discernible when it carves a dust gap wider than the wavelength of the PEI.

Areli Castrejon↗

NASA NTRS2003

The Langley Stability and Transition Analysis Code (LASTRAC) : LST, Linear and Nonlinear PSE for 2-D, Axisymmetric, and Infinite Swept Wing Boundary Layers

During the past two decades, our understanding of laminar-turbulent transition flow physics has advanced significantly owing to, in a large part, the NASA program support such as the National Aerospace Plane (NASP), High-speed Civil Transport (HSCT), and Advanced Subsonic Technology (AST). Experimental, theoretical, as well as computational efforts on various issues such as receptivity and linear and nonlinear evolution of instability waves take part in broadening our knowledge base for this intricate flow phenomenon. Despite all these advances, transition prediction remains a nontrivial task for engineers due to the lack of a widely available, robust, and efficient prediction tool. The design and development of the LASTRAC code is aimed at providing one such engineering tool that is easy to use and yet capable of dealing with a broad range of transition related issues. LASTRAC was written from scratch based on the state-of-the-art numerical methods for stability analysis and modem software technologies. At low fidelity, it allows users to perform linear stability analysis and N-factor transition correlation for a broad range of flow regimes and configurations by using either the linear stability theory (LST) or linear parabolized stability equations (LPSE) method. At high fidelity, users may use nonlinear PSE to track finite-amplitude disturbances until the skin friction rise. Coupled with the built-in receptivity model that is currently under development, the nonlinear PSE method offers a synergistic approach to predict transition onset for a given disturbance environment based on first principles. This paper describes the governing equations, numerical methods, code development, and case studies for the current release of LASTRAC. Practical applications of LASTRAC are demonstrated for linear stability calculations, N-factor transition correlation, non-linear breakdown simulations, and controls of stationary crossflow instability in supersonic swept wing boundary layers.

Chang, Chau-Lyan↗