Search NASA⌕ Search

SEARCH · Search NASA

Results for “Interference Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A flow visualization and aerodynamic force data evaluation of spanwise blowing on full and half span delta wings

A wind-tunnel investigation has been performed to quantify the effects of a jet on the leading-edge vortices generated by a 70-deg-sweep sharp-edged delta wing at low Reynolds numbers. Efforts were made ot optimize the jet nozzle position with respect to maximum lift increments. Both half-span force-balance testing and half- and full-span flow visualization tests were conducted. Two angles of attack were investigated, 30 and 35 deg, at Reynolds numbers of 150,000 and 200,000. Aerodynamic enhancement, including lift and drag gains of about 20 and 17 percent respectively, were measured. Results indicate an optimum jet nozzle location to be close to the leading edge, tangent to the upper wing surface, and in a direction aligned parallel to the leading edge. Nozzle interference effects, especially near the apex, were not negligible.

Visser, K. D.↗
NASA NTRS1976

Upper Surface Nacelle Influence on SCAR Aerodynamic Characteristics at Transonic Speeds

The arrow-wing transport configuration with detached engines located over the wing to produce upper surface exhaust flow effects was tested at angles of attack from -4 deg to 8 deg and jet total-pressure ratios from 1 (Jet off) to approximately 10. Wing tip leading edge flap deflections of -10 deg to 10 deg were tested with the wing-body configuration only (no nacelles). Tests were made with various nacelle chordwise, spanwise, and vertical height locations over the Mach number, angle of attack, and jet total-pressure ratio ranges. Deflecting the wing tip leading edge flap from 0 deg to -10 deg increased maximum lift to drag ratio by 1.0 at subsonic speeds. Installation of upper surface nacelles (no wing/nacelle pylons) increased the wing-body pitching moment at all Mach numbers and decreased the drag of the wing-body configuration at subsonic Mach numbers. Jet exhaust interference effects were negligible.

Mercer, C. E.↗
NASA NTRS2004

Strategy Developed for Selecting Optimal Sensors for Monitoring Engine Health

Sensor indications during rocket engine operation are the primary means of assessing engine performance and health. Effective selection and location of sensors in the operating engine environment enables accurate real-time condition monitoring and rapid engine controller response to mitigate critical fault conditions. These capabilities are crucial to ensure crew safety and mission success. Effective sensor selection also facilitates postflight condition assessment, which contributes to efficient engine maintenance and reduced operating costs. Under the Next Generation Launch Technology program, the NASA Glenn Research Center, in partnership with Rocketdyne Propulsion and Power, has developed a model-based procedure for systematically selecting an optimal sensor suite for assessing rocket engine system health. This optimization process is termed the systematic sensor selection strategy. Engine health management (EHM) systems generally employ multiple diagnostic procedures including data validation, anomaly detection, fault-isolation, and information fusion. The effectiveness of each diagnostic component is affected by the quality, availability, and compatibility of sensor data. Therefore systematic sensor selection is an enabling technology for EHM. Information in three categories is required by the systematic sensor selection strategy. The first category consists of targeted engine fault information; including the description and estimated risk-reduction factor for each identified fault. Risk-reduction factors are used to define and rank the potential merit of timely fault diagnoses. The second category is composed of candidate sensor information; including type, location, and estimated variance in normal operation. The final category includes the definition of fault scenarios characteristic of each targeted engine fault. These scenarios are defined in terms of engine model hardware parameters. Values of these parameters define engine simulations that generate expected sensor values for targeted fault scenarios. Taken together, this information provides an efficient condensation of the engineering experience and engine flow physics needed for sensor selection. The systematic sensor selection strategy is composed of three primary algorithms. The core of the selection process is a genetic algorithm that iteratively improves a defined quality measure of selected sensor suites. A merit algorithm is employed to compute the quality measure for each test sensor suite presented by the selection process. The quality measure is based on the fidelity of fault detection and the level of fault source discrimination provided by the test sensor suite. An inverse engine model, whose function is to derive hardware performance parameters from sensor data, is an integral part of the merit algorithm. The final component is a statistical evaluation algorithm that characterizes the impact of interference effects, such as control-induced sensor variation and sensor noise, on the probability of fault detection and isolation for optimal and near-optimal sensor suites.

Source record↗
DOE OSTI2025

Dynamic Excitonic Beam Switching with Atomically‐Thin Binary Blazed Gratings

Abstract Beam steering metasurfaces are ultra‐compact optical coatings that offer on‐demand redirection of optical power to specific diffraction orders. To achieve this, spatial gradients are commonly introduced in the phase of light scattered by plasmon or Mie resonant nanoparticles within the metasurface grating's unit cell. However, these phase gradients are oftentimes difficult to tune post‐fabrication. Recently, excitons in monolayer 2D semiconductors have emerged as a new metasurface building block, due to their strong and electrically‐tunable resonant light‐matter interaction. These 2D excitonic metasurfaces offer the tantalizing prospect of beam switching within a single monolayer. Here, it is demonstrated how the 2D analog of binary blazed gratings enables such beam switching by mere nanopatterning of a large monolayer WS 2 , even though nanoscale ribbons of WS 2 do not support geometrical resonances. By introducing a gradient in the nanoribbon width within the metasurface unit cell, an amplitude gradient combined with a small phase gradient in the scattered fields results in asymmetric diffraction efficiencies. Using a scattered‐field analysis, it is shown that these gradients can be further engineered via interference effects with the substrate reflection. Finally, the electrical tunability of the exciton resonance is leveraged to achieve selective and dynamic beam switching with an atomically‐thin metasurface.

Guarneri, Ludovica [Van der Waals‐Zeeman Institute↗
DOE OSTI2026

Precision measurements of Higgs hadronic decay modes at the FCC-ee

The expected precision at the FCC-ee on the product $σ$ x $\mathcal{B} \large{(}H → b\bar{b}, c\bar{c}, s\bar{s}, gg\large{)}$ of Higgs boson production cross sections times branching ratios of hadronic decays is presented. This study provides the first comprehensive determination of all major hadronic Higgs decay modes in a combined fit at future $e^+e^−$ colliders, using both Higgs-strahlung $(ZH)$ and Vector boson fusion $(v\bar{v}H)$ production processes, with a full treatment of interference effects in the $v\bar{v}jj$ final state. It assumes four identical IDEA detectors collecting $e^+e^−$ collisions at $\sqrt{s}$ = 240 and 365 GeV. The combination of all channels across both energies, with full covariance between production and decay modes, yields a production cross-section times branching-ratio precision at the percent to per-mil level for the dominant hadronic final states $(b\bar{b}, c\bar{c}, gg)$. These results provide a comprehensive input to the determination of Higgs coupling projections at the FCC-ee, and they establish for the first time sensitivity to the rare decay $H → s\bar{s}$, demonstrating that FCC-ee has the potential to provide evidence of the strange-quark Yukawa coupling.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Non-perturbative quarkonium dissociation rates in strongly coupled quark-gluon plasma

Heavy quarks and quarkonia are versatile probes of the transport properties of the hot QCD medium produced in ultra-relativistic heavy-ion collisions (URHICs). A robust description of heavy-flavor transport coefficients requires a microscopic approach that treats the open and hidden heavy-flavor sectors on the same footing. Here, we employ the quantum many-body T -matrix formalism to evaluate the dissociation rates of heavy quarkonia in the quark-gluon plasma (QGP). The basic ingredient is the heavy-light T -matrix, which utilizes a nonperturbative driving kernel constrained by lattice-QCD data. Its resummation in a ladder series provides a much enhanced interaction strength compared to a previously used perturbative coupling to the quasiparticle partons in the QGP. The in-medium quarkonium properties, particularly their temperature-dependent binding energies, are obtained from selfconsistent calculations with the same interaction kernel, including interference effects (also referred to as the imaginary part of the heavy-quark potential) as well as off-shell parton spectral functions. We systematically investigate the interplay of these effects and elaborate on the connections to the dipole approximation used in effective field theory.

effective field theories of QCD↗
DOE OSTI2024

Measurement of the impact-parameter dependent azimuthal anisotropy in coherent $ρ$ 0 photoproduction in Pb–Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV

This Letter presents the first measurement of the impact-parameter dependent angular anisotropy in the decay of coherently photoproduced $ρ$ 0 mesons. The $ρ$ 0 mesons are reconstructed through their decay into pion pairs. The measured anisotropy corresponds to the amplitude of the cos(2φ) modulation, where φ is the angle between the two vectors formed by the sum and the difference of the transverse momenta of the pions, respectively. The measurement was performed by the ALICE Collaboration at the LHC using data from ultraperipheral Pb–Pb collisions at a center-of-mass energy of $\sqrt{s_{NN}}$ = 5.02 TeV per nucleon pair. Different impact-parameter regions are selected by classifying the events in nuclear-breakup classes. The amplitude of the cos(2φ) modulation is found to increase by about one order of magnitude from large to small impact parameters. Theoretical calculations describe the measured cos(2φ) anisotropy and its impact-parameter dependence as the result of a quantum interference effect at the femtometer scale, arising from the ambiguity regarding which of the nuclei is the photon source in the interaction.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Spontaneous Formation of Single-Crystalline Spherulites in a Chiral 2D Hybrid Perovskite

In two-dimensional (2D) chiral metal-halide perovskites (MHPs), chiral organic spacers induce structural chirality and chiroptical properties in the metal-halide sublattice. This structural chirality enables reversible crystalline-glass phase transitions in (S-NEA) 2 PbBr 4 , a prototypical chiral 2D MHP where NEA + represents 1-(1-naphthyl)ethylammonium. Here, in this study, we investigate two distinct spherulite states of (S-NEA) 2 PbBr 4 , exhibiting either radial-like or stripe-like banded patterns depending on the annealing conditions of the amorphous film. Despite similarities in optical absorption and photoluminescence, the stripe-like, banded spherulite exhibits higher crystallinity and improved optical transparency compared to those of radial-like spherulite. X-ray nanoprobe measurements reveal tilting-angle modulations in the octahedral plane of stripe-like spherulites, correlating with the film’s surface geometry. Transfer matrix calculations indicate that the optical contrast in stripe-like patterns, seen in bright-field optical microscopy, arises from optical interference effects, differing from the contrast mechanism observed in polymer spherulites. Ultrafast carrier dynamics experiments suggest that the stripe-like spherulites resemble single crystals more closely than radial-like spherulites, while electrical conductivity measurements show enhanced charge carrier transport in stripe-like spherulites. These findings offer insights into MHP spherulite states with a single composition but different morphologies, previously observed only in polymers, highlighting their potential for optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Purcell enhancement of directional edge photocurrent in a van der Waals self-cavity

Cavities provide a means to manipulate the optical and electronic responses of quantum materials by selectively enhancing light-matter interaction at specific frequencies and momenta. While cavities typically involve external structures, exfoliated flakes of van der Waals (vdW) materials can form intrinsic self-cavities due to their small finite dimensions, confining electromagnetic fields into plasmonic cavity modes, characterized by standing-wave current distributions. While cavity-enhanced phenomena are well-studied at optical frequencies, the impact of self-cavities on nonlinear electronic responses—such as directional photocurrent—remains largely unexplored, particularly in the terahertz regime, critical for emerging ultrafast optoelectronic technologies. Here, we report a self-cavity-induced Purcell enhancement of directional photocurrents in the vdW semimetal WTe 2 . Using ultrafast optoelectronic circuitry, we measured coherent near-field THz emission resulting from nonlinear photocurrents excited at the sample edges. We observed enhanced emission at finite frequencies, tunable via excitation fluence and sample geometry, which we attribute to plasmonic interference effects controlled by the cavity boundaries. We developed an analytical theory that captures the cavity resonance conditions and spectral response across multiple devices. Our findings establish WTe 2 as a bias-free, geometry-tunable THz emitter and demonstrate the potential of self-cavity engineering for controlling nonlinear, nonequilibrium dynamics in quantum materials.

condensed-matter physics↗
DOE OSTI2026

Non-adiabatic quantum interference and complex formation in ultracold collisions of Rb with KRb

Ultracold elastic collisions of 87 Rb with 40 K 87 Rb in its ground vibrational and rotational state are investigated using a first principles based theoretical methodology. Full-dimensional ab initio computed potential energy surfaces are reported that include the two lowest-lying electronic states, their conical intersection, non-adiabatic couplings and an accurate long-range behavior. A numerically exact time-independent quantum dynamics method in hyperspherical coordinates is used to compute the elastic scattering cross sections, rate coefficients and collision lifetime spectrum. The quantum scattering calculations include all degrees of freedom and treat both electronic states and their non-adiabatic couplings using a two-state diabatic representation. The theoretically computed elastic rate coefficient is in good agreement with the recently reported experimental value. Significant non-adiabatic quantum interference effects are shown to originate from the unique properties of ultracold collisions and the geometric phase associated with the conical intersection. A high-resolution collision energy grid is used to investigate the origin of the experimentally reported long-lived 3-body collision complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Enhanced quantum efficiency from optical interference in alkali antimonide photocathodes: Modeling and experimental results

We present measurements of enhanced quantum efficiency (QE) in thin film alkali antimonide photocathodes from optical interference in the cathode-substrate multilayer. Modulations in the spectral response are observed over a range of visible wavelengths and are shown to increase the QE by more than a factor of two at specific wavelengths. We present a model describing the QE modulations based on the three step photoemission process incorporating cases of both constant density of states and density functional theory-derived density of states and show that the calculated results are in good agreement with the measurements. Model predictions demonstrate that QE can be enhanced by more than a factor of 5 by optimization of cathode and substrate layer thicknesses. Additionally, these calculations reveal that optical interference can yield higher quantum efficiencies in thin films compared to thick, optically dense films. We model the QE vs excitation wavelength of multiple alkali antimonide compounds at different thicknesses. We then discuss the advantages of this interference effect for electron accelerators.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Relaxing Direct Ptychography Sampling Requirements via Parallax Imaging Insights

Direct ptychography enables the retrieval of information encoded in the phase of an electron wave passing through a thin sample by deconvolving the interference effects of a converged probe with known aberrations. Under the weak phase object approximation, this permits the optimal transfer of information using noniterative techniques. However, the achievable resolution of the technique is traditionally limited by the probe step size—setting stringent Nyquist sampling requirements. At the same time, parallax imaging has emerged as a dose-efficient phase technique which relaxes sampling requirements and enables scan-upsampling. Here, we formulate parallax imaging as a quadratic approximation to part of the direct ptychography kernel and use this insight to enable upsampling in direct ptychography. We validate our analytical results numerically using simulated and experimental reconstructions.

direct ptychography, parallax imaging, scan Nyquis↗
DOE OSTI2025

Attosecond X-Ray Core-Level Chronoscopy of Aromatic Molecules

Attosecond photoemission or photoionization delays are a unique probe of the structure and the electronic dynamics of matter. However, the spectral congestion of valence photoelectron spectra sets fundamental limits to the complexity of systems that can be studied, and the delocalization of valence electron wave functions blurs the spatial origin of the photoelectron wave packet. Using attosecond x-ray pulses from LCLS, we demonstrate the key advantages of measuring core-level delays: The photoelectron spectra remain atomlike, the measurements become element specific, and the observed scattering dynamics originate from a pointlike source when multicenter interference effects are negligible. We exploit these unique features to reveal the effects of changing functional groups (C-H vs N) and symmetry on attosecond scattering dynamics by measuring and calculating the photoionization delays between N−1⁢𝑠 and C−1⁢𝑠 core shells of a series of aromatic azabenzene molecules. Remarkably, the delays increase with the number of nitrogen atoms in the molecule and reveal multiple resonances. We identify two previously unknown mechanisms regulating the associated attosecond dynamics, namely the enhanced confinement of the trapped wave function with the replacement of C-H groups by N atoms and the decrease of the coupling strength among the photoemitted partial waves with increasing symmetry. This study demonstrates the unique opportunities opened by measurements of core-level photoionization delays for unraveling attosecond electron dynamics in complex matter.

Ji, Jia-Bao [Eidgenoessische Technische Hochschule↗
DOE OSTI2024

Accessing the gluon GTMD F 1 , 4 in exclusive π 0 production in e p collisions

We demonstrate that the longitudinal single target-spin asymmetry in exclusive π 0 production in e p collisions can give access to the imaginary part of the gluon generalized transverse momentum distribution (GTMD) F 1 , 4 . Such a longitudinal spin asymmetry that results from the Coulomb-nuclear interference effect, leads to a characteristic azimuthal angular correlation of sin 2 ϕ , where ϕ is the azimuthal angle between the scattered lepton transverse momentum and the recoil proton’s transverse momentum. We also present a numerical estimate of the asymmetry for the kinematics accessible at EIC and EicC. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Event generator for jet tomography in electron-ion collisions

We develop the first event generator, the electron-heavy-ion-jet-interaction-generator (eHIJING), for the jet tomography study of electron-ion collisions. In this generator, energetic jet partons produced from the initial hard scattering undergo multiple collisions with the nuclear target. The collision rate is proportional to the transverse-momentum-dependent (TMD) gluon density in the nucleus, which is given by a simple model inspired by the physics of gluon saturation. Medium-modified QCD splitting functions within the higher-twist (HT) and generalized higher-twist (GHT) frameworks are utilized to simulate parton showering in the nuclear medium that takes into account the non-Abelian Landau-Pomeranchuck-Midgal interference effect. Employing eHIJING, we revisit hadron production in semi-inclusive deep inelastic scattering (SIDIS) as measured by EMC, HERMES, and recent CLAS experiments. eHIJING with both GT and GHT frameworks gives reasonably good descriptions of these experimental data. Predictions for experiments at the future electron-ion colliders are also provided. It is demonstrated that future measurements of the transverse momentum broadening of single hadron spectra can be used to map out the two-dimensional kinematic (Q 2 , x B ) dependence of the jet transport coefficient $\hat{q}$ in cold nuclear matter.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

Weak localization and universal conductance fluctuations in large-area twisted bilayer graphene

We study diffusive magnetotransport in highly 𝑝-doped large-area twisted bilayer graphene in 1∘, 7∘, 9∘, and 20∘ samples. All samples exhibit weak localization, from which we extract the phase coherence length and intervalley scattering lengths, and from that determine that dephasing is caused by electron-electron scattering and intervalley scattering is caused by point defects. We observe signatures of universal conductance fluctuations in the 9∘ sample, which has high mobility and is near the van Hove singularity. Further improvements in sample quality and applications to large-area moiré materials will open new avenues to observe quantum interference effects.

Talkington, Spenser [University of Pennsylvania]↗