Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

First-principles investigation of thermodynamic, elastic and electronic properties of Al{sub 3}V and Al{sub 3}Nb intermetallics under pressures

The thermodynamic, elastic, and electronic properties of D0{sub 22}-type Al{sub 3}V and Al{sub 3}Nb intermetallics were studied using the first-principle method. The results showed the pressure has profound effects on the structural, mechanical and electronic properties in both Al{sub 3}V and Al{sub 3}Nb. Thermodynamically, the formation enthalpies for Al{sub 3}V and Al{sub 3}Nb were derived, which agreed well with available experimental and theoretical values. Comparably, Al{sub 3}Nb was a more stable phase with the more negative H{sub f} than Al{sub 3}V. Mechanically, the calculated elastic constants showed linearly increasing tendencies, and satisfied the Born's criteria from 0–20 GPa, indicating the mechanically stability of Al{sub 3}V and Al{sub 3}Nb under this pressure range. Further, the mechanical parameters (i.e., bulk modulus (B), shear modulus (G), and Young's modulus (E)) were derived using the Voigt-Reuss-Hill (VRH) method, and in good agreement with available experimental results at the ground state. All these parameters presented the linearly increasing dependences on the external pressure. The B/G ratios and Poisson's ratio indicated that the Al{sub 3}V and Al{sub 3}Nb crystals should exhibit brittle behavior at 0–20 GPa. Additionally, the bulk modulus can be obtained through fitting the Birch-Murnaghan equation (B{sub 0}), computing by VRH method (B{sub H}), and deriving from the elastic theory (B{sub relax}) in both intermetallics. The uniformity of these calculated bulk moduli in each compound exhibited the excellent reliability and self-consistency. In addition, Debye temperature was estimated from the average sound velocity. The Debye temperature showed an increasing dependence on the pressures. Finally, through density of states analysis, Al{sub 3}V and Al{sub 3}Nb were suggested to possess naturally metallic behavior. Under pressures, it was noted that the shapes of peaks and pseudogaps exhibited relative few changes, suggesting Al{sub 3}V and Al{sub 3}Nb has kept structurally stable up to 20 GPa. At zero pressure, Al{sub 3}Nb was considered as a more structurally stable phase with the more number of bonding electrons per atom than Al{sub 3}V. This conclusion was in consistent with the one drawn from the thermodynamic analysis.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Elastic anisotropy, vibrational, and thermodynamic properties of U{sub 2}Ti intermetallic compound with AlB{sub 2}-type structure under high pressure up to 100 GPa

Structural, elastic anisotropy, dynamical, and thermodynamic properties of U{sub 2}Ti have been studied by employing density functional theory and density functional perturbative theory. The optimized lattice parameters a, c, unit volume V, bulk modulus B, and bond lengths d{sub U-U}, d{sub U-Ti} of U{sub 2}Ti are in favorable agreement with the available experimental data and other theoretical values. The elastic constants under pressure were obtained using “energy-strain” method. The polycrystalline modulus, Poisson's ratio, brittle/ductile characteristics, Debye temperature and the integration of elastic wave velocities over different directions, and hardness under pressure are also evaluated successfully. The anisotropy of the directional bulk modulus and the Young's modulus is systematically predicted for the first time. It turns out that U{sub 2}Ti should be stabilized mechanically up to 100 GPa, this compound just possesses slightly elastic anisotropy at zero pressure; however, the anisotropy becomes more and more significant with the increasing pressure. In particular, the phonon dispersion curves and phonon density of state under pressure are reported for the first time. The Raman and infrared-active phonon modes at Γ point are further assigned. Our results indicate that U{sub 2}Ti is also stable dynamically up to 100 GPa. Additionally, within the calculated phonon density of states, the thermodynamic properties are predicted.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modelling of single walled carbon nanotube cylindrical structures with finite element method simulations

In this study, the modulus of elasticity and shear modulus values of single-walled carbon nanotubes SWCNTs were modelled by using both finite element method and the Matlab code. Initially, cylindrical armchair and zigzag single walled 3D space frames were demonstrated as carbon nanostructures. Thereafter, macro programs were written by the Matlab code producing the space truss for zigzag and armchair models. 3D space frames were introduced to the ANSYS software and then tension, compression and additionally torsion tests were performed on zigzag and armchair carbon nanotubes with BEAM4 element in obtaining the exact values of elastic and shear modulus values. In this study, two different boundary conditions were tested and especially used in torsion loading. The equivalent shear modulus data was found by averaging the corresponding values obtained from ten different nodal points on the nanotube path. Finally, in this study it was determined that the elastic constant values showed proportional changes by increasing the carbon nanotube diameters up to a certain level but beyond this level these values remained stable.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

FP-LAPW study of structural, electronic, elastic, mechanical and thermal properties of AlFe intermetallic

The structural, electronic, elastic, mechanical and thermal properties of AlFe intermetallic compound in B{sub 2}-type (CsCl) structure have been investigated using first-principles calculations. The exchange-correlation term was treated within generalized gradient approximation. Ground state properties i.e. lattice constants (a{sub 0}), bulk modulus (B) and first-order pressure derivative of bulk modulus (B’) are presented. The density of states are derived which show the metallic character of present compound. Our results for C{sub 11}, C{sub 12} and C{sub 44} agree well with previous theoretical data. Using Pugh’s criteria (B/G{sub H} < 1.75), brittle character of AlFe is satisfied. In addition shear modulus (G{sub H}), Young’s modulus (E), sound wave velocities and Debye temperature (θ{sub D}) have also been estimated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental equation of state of 11 lanthanide nitrides (NdN to LuN) and pressure induced phase transitions in NdN, SmN, EuN, and GdN

Through an extensive data analysis of powder X-ray diffraction data obtained at pressures up to at least 78 GPa, we report the experimental equations of state for all lanthanide nitrides between NdN and LuN, excluding the radioactive Pm. By fitting the obtained unit cell volumes as a function of pressure with the third order Birch–Murnaghan equation of state, we find that the bulk modulus increases with an increasing lanthanide number from K 0 = 146(12) GPa for NdN to 182(7) GPa in EuN. Hereafter, the bulk modulus reaches a plateau for the rest of the series except for TmN which has a lower bulk modulus. We find that the first derivative of the bulk modulus is around 4 for all compounds except TbN, which displays a significantly different compression behavior. In addition, we find a B1 to B10 pressure-induced phase transition in NdN, SmN, EuN, and GdN at increasingly higher pressures. In fact, we observe that the onset pressure of the phase transition increases linearly with Ln atomic number. From TbN and onwards, we do not observe any sign of a B1 to B10 transition indicating that the transition pressure exceeds the studied pressure range. Therefore, we believe that, for the heavier lanthanides, the linear relationship between the onset pressure and the lanthanide number does not hold and even higher pressures are needed to observe the transition. This coherent study of the series of lanthanide nitrides offers a unique opportunity for benchmark studies of computational methods applied to compounds with 4f electrons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Carbon Nanofiber Clustering on the Micromechanical Properties of a Cement Paste

The use of carbon nanofibers (CNFs) in cement systems has received significant interest over the last decade due to their nanoscale reinforcing potential. However, despite many reports on the formation of localized CNF clusters, their effect on the cement paste micromechanical properties and relation to the mechanical response at the macroscopic scale are still not fully understood. In this study, grid nanoindentation coupled with scanning electron microscopy and energy dispersive spectroscopy was used to determine the local elastic indentation modulus and hardness of a portland cement paste containing 0.2% CNFs with sub-micro and microscale CNF clusters. The presence of low stiffness and porous assemblage of phases (modulus of 15–25 GPa) was identified in the cement paste with CNFs and was attributed primarily to the interfacial zone surrounding the CNF clusters. The CNFs favored the formation of higher modulus C–S–H phases (>30 GPa) in the bulk paste at the expense of the lower stiffness C–S–H. Nanoindentation results combined with a microscale–macroscale upscaling homogenization method further revealed an elastic modulus of the CNF clusters in the range from 18 to 21 GPa, indicating that the CNF clusters acted as compliant inclusions relative to the cement paste.

36 MATERIALS SCIENCE↗

Correlation between failure and local material property in chopped carbon fiber chip-reinforced sheet molding compound composites under tensile load

To develop further understanding towards the role of a heterogeneous microstructure on tensile crack initiation and failure behavior in chopped carbon fiber chip-reinforced composites, uni-axial tensile tests are performed on coupons cut from compression molded plaque with varying directions. Our experimental results indicate that failure initiation is relevant to the strain localization, and a new criterion with the nominal modulus to predict the failure location is proposed based on the strain analysis. Furthermore, optical microscopic images show that the nominal modulus is determined by the chip orientation distribution. At the area with low nominal modulus, it is found that chips are mostly aligning along directions transverse to loading direction and/or less concentrated, while at the area with high nominal modulus, more chips are aligning to tensile direction. On the basis of failure mechanism analysis, it is concluded that transversely-oriented chips or resin-rich regions are easier for damage initiation, while longitudinally-oriented chips postpone the fracture. Good agreement is found among failure mechanism, strain localization and chip orientation distribution.

36 MATERIALS SCIENCE↗

Effect of laminae count and manufacturing methods on mechanical properties of thin‐ply woven composites

Abstract Thin‐ply woven composites exhibit exceptional mechanical performance by delaying the onset of damage, making them suitable for high‐performance structural applications. This study outlines the impact of manufacturing techniques (vacuum bagging and hot pressing), ply count, and fiber waviness on the mechanical properties of aromatic thermosetting copolyester/carbon‐fiber (ATSP/CF) composites. The analysis encompasses several different ply counts, evaluating their effects on the in‐plane elastic modulus (0°–90°) and tensile strength. Results demonstrate that reducing the waviness (or crimp) ratio significantly enhances the in‐plane elastic modulus, with improvements up to 188%, highlighting the importance of fiber alignment. Vacuum bagging produced ply thicknesses from 128 to 58 μm for 1–36 plies, with in‐plane elastic moduli from 30.3 to 87.2 GPa, and 4‐ and 8‐ply samples showed approximately 40% higher stiffness than those made by hot pressing. ATSP resin with high thermal stability (up to 400°C) and recyclability was used. Furthermore, this study highlights the microstructural enhancements achieved through vacuum bagging, as revealed by scanning electron and optical microscopy, and micro‐computed tomography imaging. This paper provides insights into damage mitigation and achieving enhanced mechanical properties by controlling fiber waviness using vacuum bagging and higher ply count in thin‐ply ATSP/CF composites. Highlights Crimp ratio reduction enhances elastic in‐plane elastic modulus up to 188%. Vacuum bagging increases modulus over the hot pressing manufacturing method by 40%. Lowering thickness‐per‐ply increases failure strain from 0.8% to 1.2%. Explored the performance of a novel ATSP matrix with high recyclability and thermal stability.

Kushwaha, Shashank [The Grainger College of Engine↗

Inverse measurement of stiffness by the normalization technique for J-integral fracture toughness

The single specimen normalization technique for J-integral fracture toughness has been successfully employed by several researchers to study the strongly non-linear fracture response of ductile semicrystalline polymers. As part of the normalization technique the load and the plastic component of displacement are normalized. The normalized data is then fit with a normalization function that approximates a power law for small displacements that are dominated by blunting and smoothly transitions to a linear relationship for large displacements that are dominated by stable crack extension. Particularly for very ductile polymers the compliance term used to determine the plastic displacement can dominate the solution and small errors in determining the elastic modulus can lead to large errors in the normalization or even make it ill-posed. This can be further complicated for polymers where the elastic modulus is strong strain rate dependent and simply using a 'quasistatic' modulus from a dogbone measurement may not equate to the dominant strain rate in the compact tension specimen. The current work proposes directly measuring the compliance of the compact tension specimen in the solution of J-integral fracture toughness and then solving for the elastic modulus. By comparison with a range of strain rate data the dominant strain rate can then be determined.

36 MATERIALS SCIENCE↗

Assessment and Response of Treated Cocos nucifera Reinforced Toughened Epoxy Composite Towards Fracture and Viscoelastic Properties

The current research work is dedicated to addressing the fibre orientation problem and environmental issues through the development of micron-sized coir particle reinforced epoxy composite with enhanced fracture toughness and viscoelastic properties. A ‘specific grade’ standard epoxy adhesive based polymer composite is produced with reinforcement of surface modified coir particle filler. The surface modification on raw coir filler is carried out by NaOH and confirmed by Fourier transform infrared spectroscopy (FTIR), X-ray diffractogram and thermogravimetric analysis (TGA). The reduced intensity of hydroxide functional group as well as the enhanced thermal stability of surface modified coir filler is observed by FTIR and TGA respectively. The properties of produced composite samples are investigated by tensile test with low to high strain rate, fracture toughness test and dynamic mechanical analysis. The investigation revealed an improvement in tensile strength, fracture toughness and storage modulus values of toughened coir–epoxy composite with filler loading. The maximum value of ultimate tensile strength, modulus of elasticity and fracture toughness were 27.58 MPa, 0.738 GPa and 1.792 MPa m{sup 1/2}. The constraints like strain rate and filler content demarcated some critical effects on tensile strength, Young’s modulus and modulus of rupture. The research work suggests the applicability of the developed material as household items, replacement of timber product for indoor and outdoor decorations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of Oxygen on the Tribomechanical Properties of Single Crystals of YBa{sub 2}Cu{sub 3}O{sub 7−δ}

This paper reports a study on the mechanical and tribological properties of ab- and a (b) c−planes of YBa{sub 2}Cu{sub 3}O{sub 7−δ} single crystals. The single crystals were grown using a CuO-BaO self-flux method. The oxygenation effect on the mechanical and tribological properties of ab- and a (b) c−planes is reported. For the ab- plane, the hardness and elastic modulus were around 6 and 50 GPa, respectively. In this case, significant differences were not observed among the hardness and elastic modulus at different oxygenation states. However, the hardness and elastic modulus for as-grown and oxygenated YBa{sub 2}Cu{sub 3}O{sub 7−δ} single crystals were different from that of the a (b) c−plane, and were observed to be slightly higher for the as-grown than for the oxygenated samples. For as-grown and oxygenated samples, we observed hardness values around 4.7 and 2.0 GPa, respectively. Regarding the elastic modulus, the values were 75 and 40 GPa, respectively. The indentation fracture toughness values on the ab- plane for the as-grown and oxygenated YBa{sub 2}Cu{sub 3}O{sub 7−δ} single crystal were 3.7 ± 1.2 and 2.9 ± 1.2 MPa m{sup 1/2}, respectively. For the ab- plane, the scratch resistance of the as-grown sample was higher than that of the oxygenated sample and the scratches under load were deeper for the oxygenated sample. As regards the a (b) c−plane, the scar features were seemingly constant through all the scratch lengths and the scratches under load were deeper and larger for the oxygenated than that for the as-grown sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Exploration of fibers produced from petroleum based-mesophase pitch and pet blends for carbon fiber production

Petroleum-derived mesophase pitch and polyethylene terephthalate (PET) were blended and melt-extruded to create precursor fibers. The raw blends, heat treated bulk materials, and fibers were all examined to determine compatibility between petroleum-derived mesophase pitch and PET. Thermal investigation of the raw blends showed the presence of both the pitch and PET in separate phases suggesting no interactions had occurred during mixing. Here, the heat-treated bulk material also showed multiple phases under polarized light while Fourier-transform infrared spectroscopy indicated that the two materials did not fully separate during extrusion. Elemental scans of the precursor fibers showed areas of high oxygen concentrations averaging 11.7% as compared to a 2% oxygen concentration across the majority of the cross-section. Tensile tests of the precursor fibers showed a decrease in average modulus as compared to pure pitch fibers; however, the depressed modulus of the blended fibers was found to be independent of the PET weight percentage. Fibers created from 5 wt.% PET had a strength value within 10% of pure pitch and a 200% increase in modulus and were therefore found to be the most promising for carbon fiber production. Pure pitch and the 5 wt.% PET fibers were stabilized and carbonized to 1000 °C. Both types of fibers were tensile tested to determine their strength and stiffness. Pure pitch carbon fibers maintained a higher strength while the carbon fibers produced from 5 wt.% PET possessed a stiffer modulus which can be attributed to their radial microstructure.

36 MATERIALS SCIENCE↗

Thermal Cycling Effects on the Thermoelectric Properties of n-Type In, Ce based Skutterudite Compounds

N-type In-filled CoSb3 are known skutterudite compounds that have shown promising thermoelectric (TE) properties resulting in high dimensionless figure of merit values at elevated temperatures. Their use in various waste heat recovery applications will require that they survive and operate after exposure to harsh thermal cycling environments. This research focused on uncovering the thermal cycling effects on thermoelectric properties of n-type In0.2Co4Sb12 and In0.2Ce0.15Co4Sb12 skutterudite compositions as well as quantifying their temperature-dependent structural properties (elastic modulus, shear modulus, and Poisson's ratio). It was observed that the Seebeck coefficient and resistivity increased only slightly in the double-filled In,Ce skutterudite materials upon thermal cycling. In the In-filled skutterudites the Seebeck coefficient remained approximately the same on thermal cycling, while electrical resistivity increased significantly after thermal cycling. Results also show that thermal conductivity marginally decreases in the case of In-filled skutterudites, whereas the reduction is more pronounced in In, Ce-based skutterudite compounds. The possible reason for this kind of reduction can be attributed to grain pinning effects due to formation of nano inclusions. High temperature structural property measurements (i.e., Young's modulus and shear modulus) are also reported and the results show that these structural properties decrease slowly as temperature increases and the compounds are structurally stable after numerous thermal cycles.

36 MATERIALS SCIENCE↗

Static and Dynamic Mechanical Properties of Graphene Oxide-Incorporated Woven Carbon Fiber/Epoxy Composite

This study investigates the synergistic effects of graphene oxide (GO) on the woven carbon fiber (CF)-reinforced epoxy composites. The GO nanofiller was incorporated into the epoxy resin with variations in the content, and the CF/epoxy composites were manufactured using a vacuum-assisted resin transfer molding process and then cured at 70 and 120 °C. An analysis of the mechanical properties of the GO (0.2 wt.%)/CF/epoxy composites showed an improvement in the tensile strength, Young’s modulus, toughness, flexural strength and flexural modulus by ~ 34, 20, 83, 55 and 31%, respectively, when compared to the CF/epoxy composite. The dynamic mechanical analysis of the composites exhibited an enhancement of ~ 56, 114 and 22% in the storage modulus, loss modulus and damping capacity (tanδ), respectively, at its glass transition temperature. The fiber–matrix interaction was studied using a Cole–Cole plot analysis.

36 MATERIALS SCIENCE↗

Characterizing Transformation Phenomena and Elastic Moduli of Austenite and Oriented Martensite of Superelastic Thin NiTi Wire through Isothermal Dynamic Mechanical Analysis

In this paper, superelastic behavior of nickel-titanium thin wires is characterized using the method of dynamic mechanical analysis. Nominal dynamic storage modulus E{sup ′} is measured as function of nominal strain and stress during isothermal superelastic tensile tests at three testing temperatures above the reverse martensitic transformation finish temperature. The method brings new information on deformation mechanisms compared to the consideration of only tensile stress–strain curves. It is shown that determination of the elastic moduli E, especially at high strain, requires to calculate the true storage modulus E{sub t}{sup ′}. Using E{sub t}{sup ′} and not E{sup ′}, elastic modulus of oriented martensite E{sub M} is determined equal to 73 GPa of the same order than the elastic modulus of austenite E{sub A} equal to 70 GPa. Two models are then proposed to simulate experimental storage moduli evolution during the tests. A first model explains the E{sup ′} evolution during stress plateau by the localization phenomenon; it leads to express E{sup ′} as function of the nominal strain. A second model describes the evolution of E{sub t}{sup ′} after the stress plateau as function of true stress and test temperature. This model permits to determine the Clausius–Clapeyron coefficient of the forward transformation.

36 MATERIALS SCIENCE↗

The high-temperature elastic moduli of polycrystalline PbTe measured by resonant ultrasound spectroscopy

The thermoelectric material PbTe has been used in a wide variety of power generator applications. However, there is limited mechanical property data available for PbTe for temperatures above room temperature. This paper reports dynamic elastic moduli measured via resonant ultrasound spectroscopy on undoped and PbI2-doped polycrystalline PbTe between room temperature and 773 K; in addition, the room temperature carrier concentration was measured by a Hall effect experiment. The Young s modulus and shear modulus of PbTe decreased linearly with temperature above room temperature, while the Poisson s ratio exhibited either monotonic increase or decrease with temperature. The Young s modulus and shear modulus values obtained during heating and cooling agreed to within 1%. The dynamic elastic moduli data obtained in this study compared well in general with literature data. The difference observed between the current study and other literature studies is explained in terms of the carrier concentration effect on elastic moduli.

36 MATERIALS SCIENCE↗

Pressure induced reactions amongst calcium aluminate hydrate phases

The compressibilities of two AFm phases (straetlingite and calcium hemicarboaluminate hydrate) and hydrogarnet were obtained up to 5 GPa by using synchrotron high-pressure X-ray powder diffraction with a diamond anvil cell. The AFm phases show abrupt volume contraction regardless of the molecular size of the pressure-transmitting media. This volume discontinuity could be associated to a structural transition or to the movement of the weakly bound interlayer water molecules in the AFm structure. The experimental results seem to indicate that the pressure-induced dehydration is the dominant mechanism especially with hygroscopic pressure medium. The Birch-Murnaghan equation of state was used to compute the bulk modulus of the minerals. Due to the discontinuity in the pressure-volume diagram, a two stage bulk modulus of each AFm phase was calculated. The abnormal volume compressibility for the AFm phases caused a significant change to their bulk modulus. The reliability of this experiment is verified by comparing the bulk modulus of hydrogarnet with previous studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effective properties of a fly ash geopolymer: Synergistic application of X-ray synchrotron tomography, nanoindentation, and homogenization models

Microstructural and micromechanical investigation of a fly ash-based geopolymer using: (i) synchrotron X-ray tomography (XRT) to determine the volume fraction and tortuosity of pores that are influential in fluid transport, (ii) mercury intrusion porosimetry (MIP) to capture the volume fraction of smaller pores, (iii) scanning electron microscopy (SEM) combined with multi-label thresholding to identify and characterize the solid phases in the microstructure, and (iv) nanoindentation to determine the component phase elastic properties using statistical deconvolution, is reported in this paper. The phase volume fractions and elastic properties are used in multi-step mean field homogenization (Mori–Tanaka and double inclusion) models to determine the homogenized macroscale elastic modulus of the composite. The homogenized elastic moduli are in good agreement with the flexural elastic modulus determined on macroscale paste beams. The combined use of microstructural and micromechanical characterization tools at multiple scales provides valuable information towards the material design of fly ash geopolymers.

36 MATERIALS SCIENCE↗