Search NASA⌕ Search

SEARCH · Search NASA

Results for “Plasma Facing Components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Deuterium pellet fueling in type-III ELMy H-mode plasmas on EAST superconducting tokamak

Type-III ELMy H-mode plasmas are a valuable operating scenario, as they may simultaneously achieve fusion power gain of Q = 10 and acceptable steady-state and peak power fluxes to the plasma-facing components. It is important to investigate cryogenic deuterium pellet injection fueling in this kind of H-mode plasma since it has been chosen as a main plasma fueling technique for ITER. Recently, pellet fueling experiments have been successfully carried out on EAST, an ITER-like tokamak. A maximum electron density of 0.73 × n GW has been obtained. It is found that ELM behavior was modified immediately and a string of small ELMs were induced when pellets were injected at a low velocity from ¯40 cm above the mid-plane on the low field side, which is different from the fact that pellets trigger signal ELMs in Type-I ELMy H-mode plasmas in other tokamaks. Furthermore, the decreased edge temperature caused by the cryogenic pellet was proposed as the reason for this ELM modification. These results will provide a useful reference for the pellet fueling in a Type-III ELMy H-mode plasma on ITER in the future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First feedback-controlled divertor detachment in W7-X: Experience from TDU operation and prospects for operation with actively cooled divertor

In the last experimental campaign (OP1.2b) of the stellarator Wendelstein 7-X (W7-X), boronisation as a mean for first wall conditioning was applied for the first time which led to strongly reduced impurity fluxes from plasma-facing components. Thermal detachment at the uncooled target plates of the test divertor unit (TDU) was reached at higher plasma densities and was accompanied by high recycling of neutrals at the target plate. A feedback control system was established in W7-X to actively control the gas injection (actuator) for plasma fuelling and impurity seeding [3] through the divertors. It allowed very successful stabilisation of the detached plasma condition state as well as mitigation of thermal overloads to some baffle tiles. Different routinely available diagnostic signals were used as input parameters (sensors). We describe the setup of the feedback control system, its performance and provide some example results with the main focus on the development of the control scheme which led to the detachment stabilisation over the entire longest (30 s) high-power discharge at W7-X so far. In view of the achieved very successful detachment stabilisation and the necessity to include simultaneous optimisation of the core performance in the future, the feedback control system is being upgraded for the upcoming campaign (OP2.1) in which the water cooled and hereby inherently steady-state capable divertor has been currently installed. The prospects and some experiment ideas for active detachment control are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development progress of the Materials Analysis and Particle Probe

The Materials Analysis and Particle Probe (MAPP) is a compact in vacuo surface science diagnostic, designed to provide in situ surface characterization of plasma facing components in a tokamak environment. MAPP has been implemented for operation on the Lithium Tokamak Experiment at Princeton Plasma Physics Laboratory (PPPL), where all control and analysis systems are currently under development for full remote operation. Control systems include vacuum management, instrument power, and translational/rotational probe drive. Analysis systems include onboard Langmuir probes and all components required for x-ray photoelectron spectroscopy, low-energy ion scattering spectroscopy, direct recoil spectroscopy, and thermal desorption spectroscopy surface analysis techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NSTX Plasma Response to Lithium Coated Divertor

NSTX experiments have explored lithium evaporated on a graphite divertor and other plasma facing components in both L- and H- mode confinement regimes heated by high-power neutral beams. Improvements in plasma performance have followed these lithium depositions, including a reduction and eventual elimination of the HeGDC time between discharges, reduced edge neutral density, reduced plasma density, particularly in the edge and the SOL, increased pedestal electron and ion temperature, improved energy confinement and the suppression of ELMs in the H-mode. However, with improvements in confinement and suppression of ELMs, there was a significant secular increase in the effective ion charge Zeff and the radiated power in H-mode plasmas as a result of increases in the carbon and medium-Z metallic impurities. Lithium itself remained at a very low level in the plasma core, <0.1%. Initial results are reported from operation with a Liquid Lithium Divertor (LLD) recently installed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advanced grazing-emission X-ray fluorescence spectroscopy with small-angle neutron scattering for in-vivo surface composition and defect/morphology surface evolution in tokamak PMI

The dynamic and extreme conditions of thermonuclear fusion tokamak plasmas render material surfaces almost impossible to examine in real-time, surface-sensitive conditions. However, combining particle-probe techniques that are not charge-state dependent open the possibilities of in-vivo diagnosis of the plasma-material interface. The reconstituted surfaces of plasma-facing components ranging from first-wall to divertor-component regions in the device vary depending on the complex plasma transport characteristics of the device. For example, in ITER it is predicted that fluxes of the order 10 22 to 10 24 and incident charged-particle energies of 100’s to 1000’s of eV will reach the surface while in the divertor regions within the private-flux and near the inner and outer-strike points would vary from a few eV to 100’s of eV governed by the complex Chodura magnetic sheath dynamics. This means that the penetration range of most charged-particle fluxes would range between 1-100’s of nm (e.g. for fuel particles of D and T and He).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NSTX plasma response to lithium coated divertor

NSTX experiments have explored lithium evaporated on a graphite divertor and other plasma-facing components in both L- and H- mode confinement regimes heated by high-power neutral beams. Improvements in plasma performance have followed these lithium depositions, including a reduction and eventual elimination of the HeGDC time between discharges, reduced edge neutral density, reduced plasma density, particularly in the edge and the SOL, increased pedestal electron and ion temperature, improved energy confinement and the suppression of ELMs in the H-mode. However, with improvements in confinement and suppression of ELMs, there was a significant secular increase in the effective ion charge Z(eff) and the radiated power in H-mode plasmas as a result of increases in the carbon and medium-Z metallic impurities. Lithium itself remained at a very low level in the plasma core, < 0.1%. Initial results are reported from operation with a Liquid Lithium Divertor (LLD) recently installed. (C) 2010 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of EMC3-Eirene to NCSX

The National Compact Stellarator eXperiment (NCSX) is a quasi-axisymmetric stellarator under construction at the Princeton Plasma Physics Laboratory. The three field period device has a major radius of 1.4 m and an average aspect ratio of 4.4, with up to 6 MW of neutral beam injection planned. The edge of a typical NCSX magnetic configuration is characterized by a region of stochastic magnetic field lines, with areas of large flux expansion that allow the isolation of plasma-wall interactions. We have investigated the use of toroidally non-continuous target plates to collect the plasma exhaust power; magnetic field line calculations have shown that such a design is capable of intercepting the majority of the power flux. As part of the design of plasma facing components for NCSX, the EMC3-EIRENE code has been implemented to model the scrape-off-layer plasma. EMC3 uses a Monte Carlo technique to solve the fluid transport equations in three dimensions and has been coupled to the neutral transport code EIRENE, allowing the self consistent calculation of plasma/neutral transport in the scrape-off layer (SOL) and the expected particle and heat fluxes to target plates. In this paper, we present the results of the application of the full set of transport equations in EMC3-EIRENE, including energy, mass, momentum, and impurity transport, to model NCSX SOL plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal energy mitigation and toroidal peaking effects in JET disruptions

Previous investigations on JET suggest half or less of plasma stored thermal energy W th is radiated (f rad,th ≲ 0.5) using either massive gas injection (MGI) or shattered pellet injection (SPI) disruption mitigation. We investigate whether the apparent incomplete f rad,th is explained by radiation peaking near the injection plume. High toroidal peaking throughout the pre-thermal quench is found in argon–deuterium MGI on JET, with typically >3× higher radiation near the injector than toroidally distant. Previously unexplained toroidal bolometry measurements in neon–deuterium SPI are reproduced with similar peaking using the Emis3D radiation analysis code. These observations align with results from Alcator C-Mod and KSTAR. This peaking is not captured by previous JET studies that found poor thermal mitigation. Two sets of neon–deuterium SPI and two sets of argon–deuterium MGI are analyzed using Emis3D. In SPI, f rad,th rises from no-plume estimates of 0.31 and 0.66 to lower bounds of 0.84 and 0.92, respectively, and f rad,th ∼ 1 is possible. In MGI, the toroidal spread of the peaking feature is poorly constrained. f rad,th up to 0.85 and 0.65 are possible using the largest possible spread, increasing from 0.42 and 0.28, although f rad,th ∼ 1 does not appear to be reached. Revised mitigation estimates on JET suggest a lower melt risk to the divertor in mitigated disruptions on ITER and SPARC than previously thought. However, peaking near injectors could increase flash melting risk on nearby plasma facing components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quantum-Classical Science for the Plasma-Material Interface in NSTXU (Final Technical Report)

Plasma facing surfaces (PFS) have a profound influence on plasma performance and choice of material for PFSs is a burning issue for tokamak reactors. Using lithium wall conditioning in NSTX has resulted in a beneficial influence on plasma behavior including control of hydrogen recycling and improvements in energy confinement, longer confinement times, edge density control, and the elimination of Edge Localized Modes. A major challenge for the NSTX-U (increased power flux, increased campaign time) as well as for other magnetic fusion devices is to extend high-performance plasmas for very long durations, and to integrate this high performance with plasma facing components (PFCs) that can withstand very high heat and particle fluxes while maintaining structural integrity with minimal retention of fusion fuel. This project directly contributed to filling up the knowledge gaps and data for the dynamics of the plasma-facing interfaces in the NSTX-U at nano and nano-to-micro scales. This was achieved by both deciphering the poorly understood nanoscale phenomenology of plasma-surface interactions and providing the connection and comparison with the experiments which provide understanding at the mesoscopic scales. We modelled the dynamic response and evolution of a mixed material surfaces (D, Li, C, B, O) to bombardment by plasma particles, and investigated microstructure changes, erosion, surface chemistry, deuterium implantation and permeation. The main objectives of the project are i) a comparison of Li and B effects when deposited on carbon, and ii) the role of oxygen and other impurities (e.g. carbon, boron) in the lithium performance. In addition to predicting and understanding the phenomenology of the processes, the project achieved deliverables on the i) plasma induced erosion rates of PFCs (outer wall, divertor, etc.), including chemical and physical sputtering yields at various temperatures (300-700K), ii) deuterium uptake/recycling rates, and iii) accurate probability rates for the processes and reactions in i-ii which were used to understand the experimental results of the J.P. Allain and B. Koel NSTX-U projects. Lithium was a distinctive focus of the project. It easily charges in contact with other fusion material atoms, giving partially or fully its external electron cloud to other atoms in its vicinity and polarizing the mixed material. Our research strategy used experimentally validated multiscale theory applied to the large, multicomponent material surface systems. With the use of US supercomputing facilities we simulated evolution of atomic charges, chemistry, retention of deuterium, sputtering and morphology by introducing the corrections to the classical molecular dynamics, like are electronegativity equalization method (EEM) and quantum-classical molecular dynamics (QCMD). The goal was to understand and quantify the dynamics of the creation and evolution of the plasma-material interface under irradiation by atoms and molecules at boronized carbon, lithiated carbon, and boronized-lithiated carbon for both solid and self-healing liquid-metal divertor.

36 MATERIALS SCIENCE↗

Conceptual Design and Analysis of In-Vessel Components for the Materials Plasma Exposure eXperiment (MPEX)

The materials plasma exposure experiment (MPEX) is a linear plasma divertor simulator currently undergoing conceptual design. The facility will expose material samples to steady-state plasma fluxes to examine plasma–material interactions (PMIs) that are expected in the next generation of fusion devices. The plasmas will be generated by a helicon source, with electron and ion heating sources of up to 800 kW possible. The peak heat fluxes of the target are expected to be up to 10 MW/m 2 . The facility will be capable of handling low-activation neutron-irradiated samples in order to examine the multivariate effects of neutron damage and plasma fluence. Neutron-irradiated samples are planned to be roughly of 10-mm diameter; however, plasma-facing components up to 60×600 mm can be accommodated. The steady-state nature of the device will require the magnetic confinement of the plasma to be achieved with superconducting magnets, with a maximum on-axis field of 2.5 T. In addition, since MPEX will be a steady-state device, in-vessel components need to be water cooled. The primary in-vessel components will be the target, the dump plate, the limiter, the skimmers, and the microwave absorber. The conceptual design of these components is presented here, including analyses that confirm that the designs are adequate to meet the requirements of MPEX operation.

Lumsdaine, Arnold↗

Sorption of atmospheric gases by bulk lithium metal

Lithium conditioning of plasma facing components has enhanced the performance of several fusion devices. Elemental lithium will react with air during maintenance activities and with residual gases (H 2 O, CO, CO 2 ) in the vacuum vessel during operations. We have used a mass balance (microgram sensitivity) to measure the mass gain of lithium samples during exposure of a ~1 cm 2 surface to ambient and dry synthetic air. For ambient air, we found an initial mass gain of several mg/h declining to less than 1 mg/h after an hour and decreasing by an order of magnitude after 24 h. A 9 mg sample achieved a final mass gain corresponding to complete conversion to Li 2 CO 3 after 5 days. Exposure to dry air resulted in a 30 times lower initial rate of mass gain. The results have implications for the chemical state of lithium plasma facing surfaces and for safe handling of lithium coated components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Propagation And Damping Of High Harmonic Fast Waves And Electron Cyclotron Waves In The Nstx-U-Device

For the spherical torus and for conventional tokamaks to be viable means of producing fusion energy there are two important requirements. The first is to heat the plasma in the experimental devices to high temperatures; preferably, to fusion relevant temperatures. The second is to drive a current in the plasma so that the fusion device operates in a steady-state mode. A pulsed fusion reactor for energy production is not desirable. A favored means to achieve both of these requirements is through the use of microwaves, commonly referred to as radio frequency waves. This proposal was to understand observations from the National Spherical Torus Experiment Upgrade (NSTX-U) device on radio frequency wave heating of the confined plasma during operations with high harmonic fast waves. The proposed research was also directed toward assisting in the optimization of the experimental modes of operation so as to maximize the heating efficiency. A detailed analysis of the experiments has shown that about one-third of the input radio frequency power does not make it into the core region of the plasma where heating is required. The losses are believed to occur primarily in the edge region where the radio frequency power is initially coupled into the plasma. Using sophisticated computational codes and theoretical models, that have been developed for the NSTX-U experimental program, this research quantified the physical processes which occur in the edge plasma and lead to a decrease in the heating efficiency. The effect of edge turbulence on the scattering of radio frequency waves was studied for waves in the ion cyclotron and electron cyclotron range of frequencies. For high harmonic fast waves in the ion cyclotron range of frequencies, simulations were carried out using a full-wave solver that was extended to the vacuum vessel wall. These simulations successfully reproduced trends that were observed experimentally. This simulation capability was also used to study the interaction of high harmonic fast waves with the scrape-off layer plasma. More recently, a new technique has been developed for the calculation of radio frequency waves in toroidal geometry that enables the simultaneous incorporation of antenna geometry, plasma facing components, the scrape off-layer, and core propagation in the high harmonic fast wave regime. The effect of turbulent plasmas on the mode conversion of extraordinary electromagnetic waves in the electron cyclotron range of frequencies in the NSTX-U plasma has been studied theoretically. In the over-dense plasmas of NSTX-U, the traditional electromagnetic waves are not effective for delivering energy and momentum to the core plasma. However, electron Bernstein waves generated by mode conversion are efficient carriers of wave energy and momentum to the core. The mode conversion occurs in the turbulent edge region. A theory for mode conversion in such plasmas has been developed. The parameters that can optimize the mode conversion can be readily determined. Also, the model is useful for experimentalists to analyze observation on a shot-to-shot basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Imaging crystal spectrometer for high-resolution x-ray measurements on electron beam ion traps and tokamaks

Here, we describe a crystal spectrometer implemented on the Livermore electron beam ion traps that employ two spherically bent quartz crystals and a cryogenically cooled back-illuminated charge-coupled device detector to measure x rays with a nominal resolving power of λ/Δλ ≥ 10 000. Its focusing properties allow us to record x rays either with the plane of dispersion perpendicular or parallel to the electron beam and, thus, to preferentially select one of the two linear x-ray polarization components. Moreover, by choice of dispersion plane and focussing conditions, we use the instrument either to image the distribution of the ions within the 2 cm long trap region, or to concentrate x rays of a given energy to a point on the detector, which optimizes the signal-to-noise ratio. We demonstrate the operation and utility of the new instrument by presenting spectra of Mo 34+ , which prepares the instrument for use as a core impurity diagnostic on the NSTX-U spherical torus and other magnetic fusion devices that employ molybdenum as plasma facing components.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Wall reflection issues for optical diagnostics in fusion devices

The problem of light reflection has been raised as a high priority issue for optical diagnostics in next step fusion devices where metallic wall environment will generate significant perturbations in the diagnostics measurements. Tore Supra is a large size tokamak equipped with water-cooled stainless-steel panels used to sustain the plasma long shot radiations. These panels are highly reflective and affect significantly optical systems. In particular, we show that the infrared imaging diagnostic, which surveys the plasma facing component surface temperature for safety purposes, can give incorrect information due to reflected light coming from the bottom limiter. In the visible range, motional Stark effect and Zeff measurements experience important drifts during the plasma heating phases due to parasitic light coming from the limiter, but also from the plasma itself when the viewing lines are facing the reflecting walls. In the next step fusion devices such as ITER, the possibility to use optical measurements needs to be accessed by a modeling of the diagnostic light in its machine environment and the development of new techniques of online correction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The influence of helium on deuterium retention in beryllium co-deposits

Tritium co-deposition with materials from the plasma-facing components is expected to be the main contributor to tritium retention in ITER. Since He will also be present in the plasma as fusion ash during the DT campaign, this study focuses on the effect of He on D retention in Be co-deposits. The PISCES-B linear plasma device was used to create co-deposited Be-D-He layers for various deposition temperatures (295 K - 475 K) and He concentrations in D - αHe plasma mixtures (0 ≤ α ≤ 0.1). Thermal desorption spectroscopy and nuclear reaction analysis were used to determine the D concentration in co-deposits. For the lowest He concentration (1%) an increase of D retention was observed for the deposition at room temperature, whereas for higher He concentrations a declining trend of D retention was found. Including 10% of He in the plasma is found to reduce D retention at deposition temperatures below 425 K and have a negligible effect at higher deposition temperatures.

36 MATERIALS SCIENCE↗

Kinetic Plasma Simulation Capabilities in the MOOSE Framework: Verification of Particle-Particle Collisions

High-fidelity simulations of complex plasma systems allow researchers to gain key insights into and understanding of these systems. To facilitate massively parallel high-fidelity plasma simulations, finite-element-based particle-in-cell capabilities are being developed within the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) based framework called Software for Advanced Large-scale Analysis of MAgnetic confinement for Numerical Design, Engineering & Research (SALAMANDER). While SALAMANDER’s primary objective is modeling edge plasmas and plasma-facing components in fusion devices, the particle-in-cell capabilities being developed are general and will support modeling low-temperature plasmas as well. Previously, collisionless magnetostatic simulation capabilities have been verified with the two-stream and Dorey-Guest-Harris instabilities, and single particle motion. Collisions were implemented using the direct simulation Monte Carlo method, and verification of this capability will be presented here several verification problems: relaxation of a randomly initialized gas to a Maxwellian distribution, Fourier heat flow, and comparison of reaction rates to both analytic calculations and those calculated using a multi-term Boltzmann solver.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Energetic ions in ITER plasmas

This paper discusses the behaviour and consequences of the expected populations of energetic ions in ITER plasmas. It begins with a careful analytic and numerical consideration of the stability of Alfvén Eigenmodes in the ITER 15 MA baseline scenario. The stability threshold is determined by balancing the energetic ion drive against the dominant damping mechanisms and it is found that only in the outer half of the plasma (r/a>0.5) can the fast ions overcome the thermal ion Landau damping. This is in spite of the reduced numbers of alpha-particles and beam ions in this region but means that any Alfvén Eigenmode-induced redistribution is not expected to influence the fusion burn process. The influence of energetic ions upon the main global MHD phenomena expected in ITER's primary operating scenarios, including sawteeth, neoclassical tearing modes and Resistive Wall Modes, is also reviewed. Fast ion losses due to the non-axisymmetric fields arising from the finite number of toroidal field coils, the inclusion of ferromagnetic inserts, the presence of test blanket modules containing ferromagnetic material, and the fields created by the Edge Localised Mode (ELM) control coils in ITER are discussed. The greatest losses and associated heat loads onto the plasma facing components arise due to the use of the ELM control coils and come from neutral beam ions that are ionised in the plasma edge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗