SEARCH · Search NASA

Results for “Predictive analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Jupiter orbiter lifetime - The hazard of Galilean satellite collision

An assessment of the long-term collision risk is made for an uncontrolled orbiting spacecraft that repeatedly enters the spatial region occupied by the satellites. Numerical data are obtained for 50-year orbit propagations which account approximately for the major perturbative effects of Jupiter oblateness, solar gravity and satellite gravity. A broad statistical viewpoint regarding the question of collision likelihood is adopted and is based on a total sample size of 480 initial orbits distributed among 4 orbit classes, 8 inclinations and 15 initial epochs. Numerical results compare favorably with an analytical prediction formula which shows that eccentric low-inclination orbits have high collision probability.

Friedlander, A. L.↗

NASA NTRS1976

Effects of multi-element acoustic treatment on compressor inlet noise

An analytic and experimental study was conducted with the objective of developing both a basic understanding of axially segmented inlet acoustic treatment liners, and design procedures for enhancing the suppression of compressor inlet radiated noise. Anechoic chamber measurements demonstrated that the multielement treatment produced significantly more low frequency suppression than uniform treatment. Further, in-duct spinning mode patterns generated by the rotating vehicle were successfully measured and used as input to an analytical prediction procedure, providing significant improvement in inlet suppression predictions. The study indicated that phased inlet liners can be designed to provide increased noise suppression compared to uniform treatment.

Kraft, R. E.↗

NASA NTRS1976

Analysis and tests of NASA coverted groove heat pipe

A low-cost thermal control heat pipe having nearly covered grooves extruded in aluminum was developed at NASA. Analytical predictions of transport capability are in excellent agreement with experimental results using ammonia. Axial heat transport predictions as a function of fluid charge are presented also for methane, ethane, propane, and butane. Experimental tests show performance considerably better than that of open groove extruded pipes and comparing favorably with that of more complicated arterial/wick configurations. For ammonia at 20 C, the covert groove pipe obtained a static wicking height of 2.5 cm and an axial heat transport capability of 143 W-m.

Source record↗

NASA NTRS1975

Hydrogen-enrichment-concept preliminary evaluation

A hydrogen-enriched fuels concept for automobiles is described and evaluated in terms of fuel consumption and engine exhaust emissions through multicylinder (V-8) automotive engine/hydrogen generator tests, single cylinder research engine (CFR) tests, and hydrogen-generator characterization tests. Analytical predictions are made of the fuel consumption and NO/sub x/ emissions which would result from anticipated engine improvements. The hydrogen-gas generator, which was tested to quantify its thermodynamic input-output relationships was used for integrated testing of the V-8 engine and generator.

Ecklund, E. E.↗

NASA NTRS1977

Solution to the Delta vehicle second stage pogo problem

A discussion of the pogo phenomenon observed on the Delta launch vehicle second stage is presented. The pressure-fed engine and the high frequency of the oscillation (125 Hz) required unique analysis and extensive testing to support analysis detail. In addition, the need to continue a one vehicle per month launch rate required both an immediate interim and a timely long-term solution to the problem. The development and implementation of a program involving analysis, ground test, and flight instrumentation is described. An analytical model was developed and used to investigate both structural and propulsion system modifications. The factors which influenced the final suppression system selection, the analytical predictions for that system, and flight data which validate that system's effectiveness are presented.

Markowitz, M.↗

NASA NTRS1977

An investigation of induced drag reduction through over-the-wing blowing

An investigation has been conducted in the Langley 16-foot transonic tunnel to verify analytically predicted benefits in climb and cruise performance due to blowing the jet exhaust over the wing for a transport configuration. A wing-body model - powered-nacelle rig combination was tested at Mach numbers of 0.5 and 0.8 at angles of attack from -2 to 4 deg and jet total pressure ratios from jet off to 3 or 4 (depending on Mach number) for a variety of nacelle locations relative to the wing. Results from this investigation show that the induced drag for the wing-body (nacelles were nonmetric) was reduced for virtually all configurations. In addition to the experimental results, comparisons of the data with available prediction methods are included to show their validity and capabilities.

Reubush, D. E.↗

NASA NTRS1976

An analytical and experimental evaluation of the plano-cylindrical Fresnel lens solar concentrator

Plastic Fresnel lenses for solar concentration are attractive because of potential for low-cost mass production. An analytical and experimental evaluation of line-focusing Fresnel lenses with application potential in the 200 to 370 C range is reported. Analytical techniques were formulated to assess the solar transmission and imaging properties of a grooves-down lens. Experimentation was based primarily on a 56 cm-wide lens with f-number 1.0. A sun-tracking heliostat provided a non-moving solar source. Measured data indicated more spreading at the profile base than analytically predicted. The measured and computed transmittances were 85 and 87% respectively. Preliminary testing with a second lens (1.85 m) indicated that modified manufacturing techniques corrected the profile spreading problem.

Hastings, L. J.↗

NASA NTRS1977

Ceramic composite protection for turbine disc bursts

Ceramic composite turbine disc protection panels for the A300B were developed using armor technology. Analytical predictions for modifying the ballistic projectile armor system were verified by a test program conducted to qualify the rotor containment system. With only a slight change in the areal density of the armor system a more than two-fold increase in kinetic energy protection level was achieved. Thickness of the fiberglass reinforced plastic backing material was increased to achieve an optimum ratio of ceramic thickness to backing thickness for the different ballistic defeat condition.

Gardner, P. B.↗

NASA NTRS1978

Fabrication and test of a variable conductance heat pipe

A variable conductance heat pipe (VCHP) with feedback control was fabricated with a reservoir-condenser volume ratio of 10 and an axially grooved action section. Tests of the heat transport capability were greater than or equal to the analytical predictions for the no gas case. When gas was added, the pipe performance degraded by 18% at zero tilt as was expected. The placement of the reservoir heater and the test fixture cooling fins are believed to have caused a superheated vapor condition in the reservoir. Erroneously high reservoir temperature indications resulted from this condition. The observed temperature gradients in the reservoir lend support to this theory. The net result was higher than predicted reservoir temperatures. Also, significant increases in minimum heat load resulted for controller set point temperatures higher than 0 C. At 30 C, control within the tolerance band was maintained, but high reservoir heater power was required. Analyses showed that control is not possible for reasonably low reservoir heater power. This is supported by the observation of a significant reservoir heat leak through the condenser.

Lehtinen, A. M.↗

NASA NTRS1978

JT9D jet engine performance deterioration

The analytical techniques utilized to examine the effects of flight loads and engine operating conditions on performance deterioration are presented. The role of gyroscopic, gravitational, and aerodynamic loads are shown along with the effect of variations in engine build clearances. These analytical results are compared to engine test data along with the correlation between analytically predicted and measured clearances and rub patterns. Conclusions are drawn and important issues are discussed.

Jay, A.↗

NASA NTRS1978

Effect of steady flight loads on JT9D-7 performance deterioration

Short term engine deterioration occurs in less than 250 flights on a new engine and in the first flights following engine repair; while long term deterioration involves primarily hot section distress and compression system losses which occur at a somewhat slower rate. The causes for short-term deterioration are associated with clearance changes which occur in the flight environment. Analytical techniques utilized to examine the effects of flight loads and engine operating conditions on performance deterioration are presented. The role of gyroscopic, gravitational, and aerodynamic loads are discussed along with the effect of variations in engine build clearances. These analytical results are compared to engine test data along with the correlation between analytically predicted and measured clearances and rub patterns. Conclusions are drawn and important issues are discussed.

Jay, A.↗

NASA NTRS1978

Measurements of acoustic sources in motion

Results of the far-field pressures measured from three different types of moving sources are presented. These acoustic sources consist of a point monopole, a small model jet, and an aircraft. Results for the pressure time history produced by the point source show good agreement with those predicted analytically. Both actual and simulated forward motion of the model jet show reductions in noise levels with forward speed at all angles between the source and observer. Measurement with the aircraft over both an anechoic floor and over the ground yields a method for evaluating the transfer function for ground reflections at various angles between the moving aircraft and measurement position.

Maestrello, L.↗

NASA NTRS1979

Experimental investigation of three helicopter rotor airfoils designed analytically

Three helicopter rotor airfoils designed analytically were investigated in a wind tunnel at Mach numbers from about 0.30 to 0.90 and Reynolds from about 0.8 to 2.3 x 10 to the 6th power. The airfoils had thickness-to-chord ratios of 0.08, 0.10, and 0.12 with maximum thickness at 40 percent chord. The camber distribution of each section was the same with maximum camber at 35 percent chord. The 10-percent-thick airfoil was also investigated at Reynolds numbers from 4.8 to 9.4 x 10 to the 6th power. The drag divergence Mach number of the 10-percent-thick airfoil is about 0.83 at a normal-force coefficient of 0 and about 0.72 at a normal-force coefficient of 0.6 at Reynolds numbers near 9 x 10 to the 6th power. The maximum normal-force coefficient is slightly less than that of the NACA 0012 airfoil tested in the same facility. The results indicate that a qualitative evaluation of the drag divergence can be made at normal-force coefficients up to the onset of boundary-layer separation by analytically predicting the onset of sonic flow at the airfoil crest. The qualitative results are conservative with respect to experimental values with the experimental drag divergence Mach number up to 0.05 higher than that indicated by analysis.

Bingham, G. J.↗

NASA NTRS1979

Modeling of premixing-prevaporizing fuel-air mixing passages

The development of a computer program for the analytical prediction of the distribution of liquid and vapor fuel in the premixing-prevaporizing passage by the direct injection method is described. The technical approach adopted for this program is to separate the problem into three parts each with its own computer code. These three parts are: calculation of the two-dimensional or axisymmetric air flow; calculation of the three-dimensional fuel droplet evaporation; and calculation of the fuel vapor diffusion. This method of approach is justified because premixing passages operate at lean equivalence ratios. Hence, a weak interaction assumption can be made wherein the airflow can affect the fuel droplet behavior but the fuel droplet behavior does not affect the airflow.

Anderson, O. L.↗

NASA NTRS1978

An analytical and experimental study of sound propagation and attenuation in variable-area ducts

The performance of sound suppression techniques in ducts that produce refraction effects due to axial velocity gradients was evaluated. A computer code based on the method of multiple scales was used to calculate the influence of axial variations due to slow changes in the cross-sectional area as well as transverse gradients due to the wall boundary layers. An attempt was made to verify the analytical model through direct comparison of experimental and computational results and the analytical determination of the influence of axial gradients on optimum liner properties. However, the analytical studies were unable to examine the influence of non-parallel ducts on the optimum linear conditions. For liner properties not close to optimum, the analytical predictions and the experimental measurements were compared. The circumferential variations of pressure amplitudes and phases at several axial positions were examined in straight and variable-area ducts, hard-wall and lined sections with and without a mean flow. Reasonable agreement between the theoretical and experimental results was obtained.

Nayfeh, A. H.↗

NASA NTRS1979

Analytical core loss calculations for magnetic materials used in high frequency high power converter applications

The basic magnetic properties under various operating conditions encountered in the state-of-the-art DC-AC/DC converters are examined. Using a novel core excitation circuit, the basic B-H and loss characteristics of various core materials may be observed as a function of circuit configuration, frequency of operation, input voltage, and pulse-width modulation conditions. From this empirical data, a mathematical loss characteristics equation is developed to analytically predict the specific core loss of several magnetic materials under various waveform excitation conditions.

Triner, J. E.↗

NASA NTRS1978

Observations on instabilities of cavitating inducers

Experimental observations of instability of cavitating inducers were made for two different inducers operating at different flow coefficients. In general, instability occurred just before head breakdown. Auto-oscillation and rotating cavitation were observed. Analysis of small-amplitude behavior of the inducer and hydraulic system is carried out, and analytical predictions of stability limits were compared with experiment.

Braisted, D.↗

NASA NTRS1979

A study of the blown flap/jet flap analogy

A study of the blown flap/jet flap analogy has been undertaken. Analytical predictions were made using both improved lifting line and optimized vortex lattice models for the jet flap. Results were compared with experimental data for three propulsive lift systems; the jet augmented flap, the externally blown flap, and the upper surface blown flap. Force increments due to changes in geometry and jet parameters were well approximated in most cases, although the absolute values of the aerodynamic forces were usually underestimated. The relatively simple jet-flap models gave performance predictions of accuracy comparable to more complex analyses.

Hough, G. R.↗