Search NASA⌕ Search

SEARCH · Search NASA

Results for “Processing temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A thermotropic liquid crystal enables efficient and stable perovskite solar modules

Perovskite solar cells have seen impressive progress in performance and stability, yet maintaining efficiency while scaling area remains a challenge. Here we find that additives commonly used to passivate large-area perovskite films often co-precipitate during perovskite crystallization and aggregate at interfaces, contributing to defects and to spatial inhomogeneity. Here we develop design criteria for additives to prevent their evaporative precipitation and enable uniform passivation of defects. We explored liquid crystals with melting point below the perovskite processing temperature, functionalization for defect passivation and hydrophobicity to improve device stability. We find that thermotropic liquid crystals such as 3,4,5-trifluoro-4'-(trans-4-propylcyclohexyl)biphenyl enable large-area perovskite films that are uniform, low in defects and stable against environmental stress factors. We demonstrate modules with a certified stabilized efficiency of 21.1% at an aperture area of 31 cm 2 and enhanced stability under damp-heat conditions (ISOS-D-3, 85% relative humidity, 85 °C) with T 86 (the duration for the efficiency to decay to 86% of the initial value) of 1,200 h, and reverse bias with (ISOS-V-1, negative maximum-power-point voltage) and without bypass diodes.

14 SOLAR ENERGY↗
DOE OSTI2023

Defect graph neural networks for materials discovery in high-temperature clean-energy applications

We present a graph neural network approach that fully automates the prediction of defect formation enthalpies for any crystallographic site from the ideal crystal structure, without the need to create defected atomic structure models as input. Here we used density functional theory reference data for vacancy defects in oxides, to train a defect graph neural network (dGNN) model that replaces the density functional theory supercell relaxations otherwise required for each symmetrically unique crystal site. Interfaced with thermodynamic calculations of reduction entropies and associated free energies, the dGNN model is applied to the screening of oxides in the Materials Project database, connecting the zero-kelvin defect enthalpies to high-temperature process conditions relevant for solar thermochemical hydrogen production and other energy applications. The dGNN approach is applicable to arbitrary structures with an accuracy limited principally by the amount and diversity of the training data, and it is generalizable to other defect types and advanced graph convolution architectures. In conclusion, it will help to tackle future materials discovery problems in clean energy and beyond.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Room temperature facile synthesis of olivine-Co 2 SiO 4 nanoparticles utilizing a mechanochemical method

Co 2 SiO 4 is a ceramic pigment and promising battery material of significant technological interest, as well as a model end-member of one of the most important mineral families in the Earth's crust and upper mantle. All previously developed methods for synthesis of Co 2 SiO 4 require high-temperature processing, which promotes grain growth, while the nanocrystalline form is required for some important technological applications. Here, we report a successful method for synthesizing nanocrystalline Co 2 SiO 4 via a simple and inexpensive high-energy ball milling mechanochemical process. Products of the synthesis were characterized by a combination of XRD and TEM, and their crystal structures and elemental compositions are reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Improving molecular alignment and charge percolation in semiconducting polymer films with highly localized electronic states through tailored thermal annealing

Here, we have recently developed a strategy to improve charge percolation efficiency in a renowned family of naphthalene-diimide bithiophene (PNDI-T2) copolymers, based on the application of a tailored thermal treatment on pre-aligned films. Here we show that the accurate choice of thermal post-processing temperatures can induce a notable lamellar thickening and an improvement of molecular alignment, the latter being favored by alkyl chains with longer branches. Correspondingly, enhanced transport properties are observed. Interestingly, these are found to be independent of lamellar thickness. In fact, within this family of molecules, characterized by a locked non-planar conformation and strong intramolecular charge localization, the orientational order within charge percolation paths was found to be the only factor dictating charge transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

RF sheath induced sputtering on Proto-MPEX. I. Sheath equivalent dielectric layer for modeling the RF sheath

The pulsed linear plasma device Prototype Material Plasma Exposure eXperiment (Proto-MPEX) uses a radio frequency (RF) helicon antenna with an aluminum nitride ceramic window for plasma production. The RF sheath created under the helicon antenna is sufficient to cause ion impact energies to be greater than the sputtering threshold of the AlN helicon window material and for impurities to be created. In this study, we investigate the RF sheath on the inner diameter of the helicon window and its impact on the impurity production rates in Proto-MPEX. Three models—a 3D COMSOL finite element RF model of the Proto-MPEX helicon region, a rectified DC sheath potential model, and the 3D Global Impurity TRansport code—are coupled together to study impurity production and transportation. This novel method of impurity generation and transport modeling spans length scales ranging from the sheath (millimeters or less) up to the full device (meters) and can be applied to other radio frequency sources and antennas in a wide range of plasma physics studies, including basic plasmas, low-temperature processing plasmas, plasma thrusters, and fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Ferroelectric behavior of sputter deposited Al 0.72 Sc 0.28 N approaching 5 nm thickness

Ferroelectric Al 1-x Sc x N has raised much interest in recent years due to its unique ferroelectric properties and complementary metal oxide semiconductor back-end-of-line compatible processing temperatures. Potential applications in embedded nonvolatile memory, however, require ferroelectric materials to switch at relatively low voltages. One approach to achieving a lower switching voltage is to significantly reduce the Al 1-x Sc x N thickness. In this work, ferroelectric behavior in 5-27 nm films of sputter deposited Al 0.72 Sc 0.28 N has been studied. We find that the 10 kHz normalized coercive field increases from 4.4 to 7.3 MV/cm when reducing the film thickness from 27.1 to 5.4 nm, while over the same thickness range, the characteristic breakdown field of a 12.5 μm radius capacitor increases from 8.3 to 12.1 MV/cm. In conclusion, the 5.4 nm film demonstrates ferroelectric switching at 5.5 V when excited with a 500 ns pulse and a switching speed of 60 ns.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Engineering of niobium surfaces through accelerated neutral atom beam technology for quantum applications

A major roadblock to scalable quantum computing is phase decoherence and energy relaxation caused by qubits interacting with defect-related two-level systems (TLSs). Native oxides present on the surfaces of superconducting metals used in quantum devices are acknowledged to be a source of TLS that decrease qubit coherence times. Reducing microwave loss by “surface engineering” (i.e., replacing the uncontrolled native oxide of superconducting metals with a thin, stable surface with predictable characteristics) can be a key enabler for pushing performance forward with devices of higher intrinsic quality factor. In this work, we present a novel approach to replace the native oxide of niobium (typically formed in an uncontrolled fashion when its pristine surface is exposed to air) with an engineered oxide, using a room-temperature process that leverages accelerated neutral atom beam (ANAB) technology at 300 mm wafer scale. This ANAB is composed of a mixture of argon and oxygen, with tunable energy per atom, which is rastered across the wafer surface. The ANAB-engineered Nb-oxide thickness was found to vary from 2 to 6 nm depending on ANAB process parameters. The modeling of variable-energy x-ray photoelectron spectroscopy data confirms the thickness and compositional control of Nb surface oxide by the ANAB process. Furthermore, these results correlate well with those from transmission electron microscopy and x-ray reflectometry. Since ANAB is broadly applicable to material surfaces, the present study indicates its promise for modification of the surfaces of superconducting quantum circuits to achieve longer coherence times.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Improved Glow Discharge Polymer Removal from Beryllium Capsules Using Ozone

Copper-doped beryllium spheres are an attractive ablator for inertial confinement fusion experiments. Beryllium spheres are made by sputtering beryllium onto spherical plastic mandrels which must then be removed through a hole that is laser drilled through the shell wall. The currently used mandrel material is glow discharge polymer. This material cannot be removed by solvent and must be “burned” out. The burnout process was originally performed by etching with dry air at 425°C, but this process can substantially roughen the inner surface, which can seed instabilities and increase mix during implosion experiments. In this paper, we explore the use of pure oxygen and ozone to reduce process temperature and improve inner and outer surface quality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Aluminum Boron Nitride Ferroelectric Field-Effect Transistors With ZnO Semiconductor Channel

The discovery of ferroelectricity in hafnium zirconium oxide (HfxZr 1−x O2) and related fluorite materials has spurred interest in ferroelectric devices suitable for integration with silicon integrated circuits (ICs), especially those that can be embedded in the back-end-of-line (BEOL) process. More recently, ferroelectricity has been found in wurtzite aluminum nitride-based materials, such as scandium and boron-doped aluminum nitride (Al 1−x ScxN and Al 1−x BxN). Although these materials currently have undesirably large coercive electric fields, and small breakdown electric field-to-coercive electric field ratio, their low processing temperatures and large remanent polarization offer intriguing possibilities for device applications. Furthermore, we report ferroelectric field-effect transistors (FeFETs) with a 15 nm thick Al0.88B0.12N layer and an 11 nm ZnO semiconductor channel, achieving a memory window >1 V and switching voltages ( V switch ) <±10 V.

42 ENGINEERING↗
DOE OSTI2020

Piezoelectric Actuation of Graphene-Coated Polar Structures

Ferroelectric materials based on lead zirconate titanate (PZT) are widely used as sensors and actuators because of their strong piezoelectric activity. However, their application is limited because of the high processing temperature, brittleness, lack of conformal deposition, and a limited possibility to be integrated with the microelectromechanical systems (MEMS). Recent studies on the piezoelectricity in the 2-D materials have demonstrated their potential in these applications, essentially due to their flexibility and integrability with the MEMS. In this work, we deposited a few layer graphene (FLG) on the amorphous oxidized Si 3 N 4 membranes and studied their piezoelectric response by sensitive laser interferometry and rigorous finite-element modeling (FEM) analysis. Modal analysis by FEM and comparison with the experimental results show that the driving force for the piezoelectric-like response can be a polar interface layer formed between the residual oxygen in Si 3 N 4 and the FLG. The response was about 14 nm/V at resonance and could be further enhanced by adjusting the geometry of the device. These phenomena are fully consistent with the earlier piezoresponse force microscopy (PFM) observations of the piezoelectricity of the graphene on SiO 2 and open up an avenue for using graphene-coated structures in the MEMS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Chemical vapor infiltration of additively manufactured preforms: Pore-resolved simulations and experimental validation

The densification of additively manufactured porous preforms by chemical vapor infiltration (CVI) is studied using pore-resolved simulations and experiments. Experimentally, 3D printed silicon carbide (SiC) preforms are subject to CVI synthesis using methyltrichlorosilane (MTS) precursor to obtain high purity SiC/SiC composites. Optical images of the cross sections of the processed preforms are analyzed to obtain the spatial porosity distribution. The numerical method is based on a level set formulation to capture the spatial distribution and time evolution of the pore scale microstructural characteristics. The coupled transport and kinetic effects are represented using a dimensionless Thiele modulus. Simulations are initialized using representative synthetic preform geometries comprising of packed particles based on the size distribution of the powder used for 3D printing. The simulation results are validated against the experimental observations in terms of total density and the distribution of residual porosity. The densification characteristics, porosity classification, concentration profiles, and structure functions are analyzed as functions of processing temperature and Thiele modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Alkali Vapor Corrosion of Spinel (MgAl 2 O 4 ) and Gahnite (ZnAl 2 O 4 ) Refractories—A Comparative Study

Alkali vapor corrosion is critical for refractories used in the kilns and furnaces of diverse high-temperature processing and manufacturing sectors such as gasifiers, cement production, and glass making. Gahnite (ZnAl 2 O 4 ) is being investigated as a potential chrome-free refractory because of its similarity with the structure and properties of magnesium aluminate (MgAl 2 O 4 ) spinel. The alkali vapor corrosion of ZnAl 2 O 4 , MgAl 2 O 4 , and Mg 0.5 Zn 0.5 Al 2 O 4 was studied, according to ASTM C987-10, at 1371°C for 24 h using sodium carbonate (Na 2 CO 3 ). The surface and the polished cross-sections of the corroded ZnAl 2 O 4 , MgAl 2 O 4 , and Mg 0.5 Zn 0.5 Al 2 O 4 specimens were analyzed using x-ray diffraction (XRD), microscopy, and energy-dispersive spectroscopy (EDS) techniques. MgO in MgAl 2 O 4 , ZnO in ZnAl 2 O 4 , Mg 0.77 Zn 0.23 O, and NaAlO 2 were detected as the corrosion products for these specimens. The extent of corrosion substantially varied among the specimens despite the similarity in the corrosion products. The corrosion resistance increased in the following order: Mg 0.5 Zn 0.5 Al 2 O 4 > MgAl 2 O 4 > ZnAl 2 O 4 . The formation of a dense MgO and Mg 0.77 Zn 0.23 O layer for MgAl 2 O 4 and Mg 0.5 Zn 0.5 Al 2 O 4 , respectively, contributed to their superior resistance to alkali vapor corrosion. The underlying corrosion mechanisms are discussed based on experimental observations supported by thermodynamic analysis. Additionally, the results suggest that a partial Zn 2+ substitution for Mg 2+ in MgAl 2 O 4 can enhance the resistance to alkali vapor corrosion.

alkali corrosion↗
DOE OSTI2023

Stabilized hole-selective layer for high-performance inverted p-i-n perovskite solar cells

P-i-n geometry perovskite solar cells (PSCs) offer simplified fabrication, greater amenability to charge extraction layers, and low-temperature processing over n-i-p counterparts. Self-assembled monolayers (SAMs) can enhance the performance of p-i-n PSCs but ultrathin SAMs can be thermally unstable. Here we report a thermally robust hole-selective layer comprised of nickel oxide (NiO x ) nanoparticle film with a surface-anchored (4-(3,11-dimethoxy-7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid (MeO-4PADBC) SAM that can improve and stabilize the NiO x /perovskite interface. The energetic alignment and favorable contact and binding between NiO x /MeO-4PADBC and perovskite reduced the voltage deficit of PSCs with various perovskite compositions and led to strong interface toughening effects under thermal stress. The resulting 1.53–electron-volt devices achieved 25.6% certified power conversion efficiency and maintained >90% of their initial efficiency after continuously operating at 65 degrees Celsius for 1200 hours under 1-sun illumination.

14 SOLAR ENERGY↗
DOE OSTI2024

Dry etching of epitaxial InGaAs/InAlAs/InAlGaAs structures for fabrication of photonic integrated circuits

A dry etching process to transfer the pattern of a photonic integrated circuit design for high-speed laser communications is described. The laser stack under consideration is a 3.2-µm-thick InGaAs/InAlAs/InAlGaAs epitaxial structure grown by molecular beam epitaxy. The etching was performed using Cl2-based inductively-coupled-plasma and reactive-ion-etching (ICP-RIE) reactors. Four different recipes are presented in two similar ICP-RIE reactors, with special attention paid to the etched features formed with various hard mask compositions, in-situ passivations, and process temperatures. The results indicate that it is possible to produce high-aspect-ratio features with sub-micron separation on this multilayer structure. Additionally, the results of the etching highlight the tradeoffs involved with the corresponding recipes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Particle size of several plutonium-238 oxide fuel samples from oxalate precipitation processes

Particle size of 238 PuO 2 powders is an important factor in determining the structural integrity of fuel pellets hot-pressed from the oxide powder. Understanding the evolution of particle size during aqueous processing is a first step in assuring control of particle size throughout the pellet formation process. Measured particle sizes are reported here, and discussed in terms of measured particle size changes occurring during calcining, observed aggregation of particulate, and particle morphology. Morphology and aggregation are related to surface energy, which governs granule formation and hot pressing behavior. Results are discussed in terms of reported dependence of oxide morphology on process temperatures and reagent concentrations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Impact Response of Cold Spray Deposited Materials

Solid-state cold spraying (CS) of metals and respective blends is becoming increasingly attractive compared to conventional high temperature processes due to the unique properties such as increased yield strength, low ductility, and differences in tensile and compressive strengths that result from microstructural features due to the CS process. Here we report the results of plate impact experiments applied to CS deposits of tantalum (Ta), niobium (Nb), and a tantalum- niobium blend (TaNb). These methods allowed for definition of the Hugoniot for each material type and allowed for assessment of the Hugoniot Elastic Limit (HEL). Scanning electron microscopy was used on recovered samples to characterize the fracture mechanism during spallation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microwave Plasma Flash Pyrolysis for Coal-to-Product Applications

Since 2010, the US coal industry has experienced a precipitous decline, with coal production volumes dropping by as much as 35% according to EIA. This decline is hardly surprising given that 90% of domestic coal use is allocated to electricity production: While coal generation supplied about 45% of the nation's power in 2010, its share is projected to fall to only 22% in 2020. Fortunately, alternative uses for coal as a feedstock rather than as energy source are available. Coal tar is an established feedstock for chemicals and high-value carbon products including carbon fiber and battery-grade graphites. At present, growth of these uses is constrained by the low availability, purity, and yields of currently available coal liquids, and high energy- and CO2-intensity of current methods of production (i.e. coking). Previously reported work conducted in a partnership with Pacific Northwest National Laboratory demonstrated technical and economic viability of flash pyrolysis of coal in a microwave plasma environment at bench scales targeting production of fuel feedstocks (synthetic oil). H Quest’s work since then indicated promise of microwave-derived coal liquids to be uniquely suited for the lower-cost production of carbon materials, including synthetic graphite, carbon fiber, and composites. Low bulk process temperatures, subsecond residence times, and ambient pressure operation enable small-scale deployment, reduce capital and operating costs, and suppress formation of impurities, including QI material, typical in conventional coal tars. With no inherent production of CO2 or water consumption, microwave plasma flash pyrolysis presents a viable route to the sustainable production of both platform chemicals and carbon-based materials. Most recently, H Quest developed a novel, ruggedized microwave plasma reactor, which departs from the proof-of-concept approach and addresses the problems typically encountered in scaling laboratory microwave plasma apparata (e.g. eliminating fragile quartz enclosures prone to coking and fouling). This reactor has been integrated with a 15kW microwave power supply, a pulverized coal injection system, and a product recovery system. A series of screening tests across a range of coals (including hv-, lv-bituminous and subbituminous PRB), entrainment gas flows and compositions and microwave energy inputs are performed to evaluate conversion rates within the novel, scaled-up system, confirm yields of liquid products, and to perform compositional (GC/MS and elemental) analyses of the products. Results of these tests will be presented and discussed.

Skoptsov, George↗