Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A theoretical study of the application of jet flap circulation control for reduction of rotor vibratory forces

The results of a study to investigate the theoretical potential of a jet-flap control system for reducing the vertical and horizontal non-cancelling helicopter rotor blade root shears are presented. A computer simulation describing the jet-flap control rotor system was developed to examine the reduction of each harmonic of the transmitted shears as a function of various rotor and jet parameters, rotor operating conditions and rotor configurations. The computer simulation of the air-loads included the influences of nonuniform inflow and blade elastic motions. (no hub motions were allowed.) The rotor trim and total rotor power (including jet compressor power) were also determined. It was found that all harmonics of the transmitted horizontal and vertical shears could be suppressed simultaneously using a single jet control.

Piziali, R. A.↗
NASA NTRS1974

Perturbation solutions for the influence of forward flight on helicopter rotor flapping stability

The stability of the flapping motion of a helicopter rotor blade in forward flight is investigated, using a perturbation technique which gives analytic expressions for the eigenvalues, including the influence of the periodic aerodynamic forces in forward flight. The perturbation solutions are based on small advance ratio (the ratio of the helicopter forward speed to the rotor tip speed). The rotor configurations considered are a single, independent blade; a teetering rotor; a gimballed rotor with three, four, and five or more blades; and a rotor with N independent blades. The constant coefficient approximation with the equations and degrees of freedom in the nonrotating frame represents the flap dynamic reasonably well for the lower frequency modes, although it cannot, of course, be completely correct. The transfer function of the rotor flap response to sinusoidal pitch input is examined, as an alternative to the eigenvalues as a representation of the dynamic characteristics of the flap motion.

Johnson, W.↗
NASA NTRS1975

On the investigation of cascade and turbomachinery rotor wake characteristics

The objective of the investigation reported in this thesis is to study the characteristics of a turbomachinery rotor wake, both analytically and experimentally. The constitutive equations for the rotor wake are developed using generalized tensors and a non-inertial frame of reference. Analytical and experimental investigation is carried out in two phases; the first phase involved the study of a cascade wake in the absence of rotation and three dimensionality. In the second phase the wake of a rotor is studied. Simplified two- and three-dimensional models are developed for the prediction of the mean velocity profile of the cascade and the rotor wake, respectively, using the principle of self-similarity. The effect of various major parameters of the rotor and the flow geometry is studied on the development of a rotor wake. Laws governing the decay of the wake velocity defect in a cascade and rotor wake as a function of downstream distance from the trailing edge, pressure gradient and other parameters are derived.

Raj, R.↗
NASA NTRS1975

Optimum performance and potential flow field of hovering rotors

Rotor and propeller performance and induced potential flowfields were studied on the basis of a rotating actuator disk concept, with special emphasis on rotors hovering out of ground effect. A new theory for the optimum performance of rotors hovering OGE is developed and presented. An extended theory for the optimum performance of rotors and propellers in axial motion is also presented. Numerical results are presented for the optimum distributions of blade-bound circulation together with axial inflow and ultimate wake velocities for the hovering rotor over the range of thrust coefficient of interest in rotorcraft applications. Shapes of the stream tubes and of the velocities in the slipstream are obtained, using available methods, for optimum and off-optimum circulation distributions for rotors hovering in and out of ground effect. A number of explicit formulae useful in computing rotor and propeller induced flows are presented for stream functions and velocities due to distributions of circular vortices over axi-symmetric surfaces.

Wu, J. C.↗
NASA NTRS1974

The rotor systems research aircraft - A flying wind tunnel

The Sikorsky Aircraft division of United Aircraft Corporation is constructing two uniquely designed Rotor Systems Research Aircraft (RSRA). These aircraft will be used through the 1980's to comparatively test many different types of rotors - articulated, hingeless, teetering, and gimballed, as well as advanced rotor concepts, such as reverse velocity and variable diameter rotors. The RSRA combines a new airframe with existing Sikorsky H-3 (S-61) dynamic components. A force measurement system is incorporated to permit accurate evaluation of significant rotor characteristics. Both rotor and fixed-wing control systems are provided, appropriately integrated for operation in the pure helicopter mode, compound helicopter mode, and fixed-wing mode. The RSRA is the first rotary wing aircraft designed with a crew escape system, including a pyrotechnic system to sever the main rotor blades.

Linden, A. W.↗
NASA NTRS1975

Experimental evaluation of multiplane-multispeed rotor balancing through multiple critical speeds

The experimentally proven range of application of the influence-coefficient balancing method, especially the least-squares procedure, is extended to include the case of multiple bending critical speeds within the operating range of a test rotor. Tests were conducted on a laboratory quality machine capable of speeds up to 18,000 rpm in order to investigate several distinct practical aspects of flexible-rotor balancing. These include: (1) balancing for operation through four bending critical speeds, (2) balancing of rotors mounted in both rigid and flexible bearing supports, (3) balancing of rotors with various amounts of measured vibration-response data and different numbers of correction planes, and (4) balancing of rotors with different arbitrary initial-unbalance configurations. The results show that a lightly damped, flexible rotor can be balanced systematically and efficiently through four bending critical speeds. It is concluded that the influence-coefficient method should be equally applicable to rotors or shafts having more than four bending critical speeds in their operating-speed ranges.

Tessarzik, J. M.↗
NASA NTRS1976

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

Preliminary estimates are presented of vibratory loads and stresses in hingeless and teetering rotors for the proposed NSF-NASA Mod-0 wind power system. Preliminary blade design utilizes a tapered tubular aluminum spar which supports nonstructural aluminum ribs and skin and is joined to the rotor hub by a steel shank tube. Stresses in the shank of the blade are calculated for static, rated, and overload operating conditions. Blade vibrations were limited to the fundamental flapping modes, which were elastic cantilever bending for hingeless rotor blades and rigid-body rotation for teetering rotor blades. The MOSTAB-C computer code was used to calculate aerodynamic and mechanical loads. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. The hingeless rotor analyzed does not appear to be structurally stable during overloads.

Spera, D. A.↗
NASA NTRS1976

A general rotor model system for wind-tunnel investigation of rotorcraft aerodynamics and acoustics

A complex rotorcraft model system has been developed by the NASA Langley Research Center and the U.S. Army Air Mobility R&D Laboratory, Langley Directorate, for aerodynamic and acoustic experimental investigations in the NASA Langley V/STOL tunnel. This generalized rotor model system has a powered main rotor, tail rotor, and auxiliary engine capability. It may be configured to represent a variety of rotorcraft configurations. The first investigation was conducted to determine the performance, acoustic, stability and control characteristics of the NASA/Army Rotor Systems Research Aircraft with an articulated rotor. In a second investigation, a quarter-scale AH-1G configuration with a teetering rotor is being represented to determine if a V-tail will improve the directional characteristics. Future programs are planned to investigate advanced rotor blade airfoils for improved performance and acoustic characteristics.

Wilson, J. C.↗
NASA NTRS1976

Correlation of full-scale helicopter rotor performance in air with model-scale Freon data

An investigation was conducted in a transonic dynamics tunnel to measure the performance of a 1/5 scale model helicopter rotor in a Freon atmosphere. Comparisons were made between these data and full scale data obtained in air. Both the model and full scale tests were conducted at advance ratios between 0.30 and 0.40 and advancing tip Mach numbers between 0.79 and 0.95. Results show that correlation of model scale rotor performance data obtained in Freon with full scale rotor performance data in air is good with regard to data trends. Mach number effects were found to be essentially the same for the model rotor performance data obtained in Freon and the full scale rotor performance data obtained in air. It was determined that Reynolds number effects may be of the same magnitude or smaller than rotor solidity effects or blade elastic modeling in rotor aerodynamic performance testing.

Yeager, W. T., Jr.↗
NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗
NASA NTRS1980

Effects of rotor parameter variations on handling qualities of unaugmented helicopters in simulated terrain flight

A coordinated analysis and ground simulator experiment was performed to investigate the effects on single rotor helicopter handling qualities of systematic variations in the main rotor hinge restraint, hub hinge offset, pitch-flap coupling, and blade lock number. Teetering rotor, articulated rotor, and hingeless rotor helicopters were evaluated by research pilots in special low level flying tasks involving obstacle avoidance at 60 to 100 knots airspeed. The results of the experiment are in the form of pilot ratings, pilot commentary, and some objective performance measures. Criteria for damping and sensitivity are reexamined when combined with the additional factors of cross coupling due to pitch and roll rates, pitch coupling with collective pitch, and longitudinal static stability. Ratings obtained with and without motion are compared. Acceptable flying qualities were obtained within each rotor type by suitable adjustment of the hub parameters, however, pure teetering rotors were found to lack control power for the tasks. A limit for the coupling parameter L sub q/L sub p of 0.35 is suggested.

Talbot, P. D.↗
NASA NTRS1981

A full-scale wind tunnel investigation of a helicopter bearingless main rotor

A helicopter bearingless main rotor was tested. Areas of investigation included aeroelastic stability, aerodynamic performance, and rotor loads as a function of collective pitch setting, RPM, airspeed and shaft angle. The rotor/support system was tested with the wind tunnel balance dampers installed and, subsequently, removed. Modifications to the rotor hub were tested. These included a reduction in the rotor control system stiffness and increased flexbeam structural damping. The primary objective of the test was to determine aeroelastic stability of the fundamental flexbeam/blade chordwise bending mode. The rotor was stable for all conditions. Damping of the rotor chordwise bending mode increases with increased collective pitch angle at constant operating conditions. No significant decrease in rotor damping occured due to frequency coalescence between the blade chordwise fundamental bending mode and the support system.

Warmbrodt, W.↗
NASA NTRS1981

Wind-tunnel investigation of the effects of blade tip geometry on the interaction of torsional loads and performance for an articulated helicopter rotor

The Langley transonic dynamics tunnel was used to determine the degree of correlation between rotor performance and the dynamic twist generated by changes in blade tip geometry using an articulated rotor with four different tip geometries at advance ratios of 0.20, 0.30 and 0.35. Based on the data obtained, it is concluded that: (1) there appears to be no strong correlation between blade torsion loads and rotor performance prediction; (2) for a given rotor task at each advance ratio investigated, both the azimuthal variation of torsional moment and the mean torsional moment at 81% radius are configuration dependent; (3) reducing the nose down twist on the advancing blade appears to be more important to forward flight performance than increasing the nose down twist on the retreating blade; (4) the rotor inflow model used was important in predicting the performance of the adaptive rotor; and (5) neither rigid blade solidity effects, inflow environment, nor blade torsion loads can be used alone to accurately predict active rotor performance.

Yeager, W. T.↗
NASA NTRS1982

An analytical investigation of the free-tip rotor for helicopters

A rotor configuration called the free-tip rotor was analytically investigated for its potential to improve helicopter forward-flight performance characteristics. This rotor differs from a conventional rotor only in the blade tip region. In this configuration, the tip is self-adjusting in pitch with respect to the rest of the blade, in accordance with a moment balance about its pitch axis. With this self-adjusting capability, the resulting pitch motion generates a more uniform airload distribution around the azimuth. Computer math models were used to compare performance characteristics of the free tip rotor with those of a conventional rotor operation at flight speeds from 130 to 160 knots. The results of this analysis indicate that the free-tip rotor improves cruise lift-drag ratio by at least 22%.

Stroub, R. H.↗
NASA NTRS1982

An investigation of rotor harmonic noise by the use of small scale wind tunnel models

Noise measurements of small scale helicopter rotor models were compared with noise measurements of full scale helicopters to determine what information about the full scale helicopters could be derived from noise measurements of small scale helicopter models. Comparisons were made of the discrete frequency (rotational) noise for 4 pairs of tests. Areas covered were tip speed effects, isolated rotor, tandem rotor, and main rotor/tail rotor interaction. Results show good comparison of noise trends with configuration and test condition changes, and good comparison of absolute noise measurements with the corrections used except for the isolated rotor case. Noise measurements of the isolated rotor show a great deal of scatter reflecting the fact that the rotor in hover is basically unstable.

Sternfeld, H., Jr.↗
NASA NTRS1980

Performance improvements with the free-tip rotor

A new rotor configuration called the free-tip rotor was investigated for its potential to improve helicopter forward-flight performance characteristics. This rotor differs from a conventional rotor only in the blade tip region. Free tip is self-adjusting in pitch with respect to the rest of the blade. With this capability, the resulting pitch motion generated a more uniform airload distribution around the azimuth. Computer math models were used to compare performance characteristics of the free-tip rotor with those of a conventional rotor operating at flight speeds from 130 to 160 knots. The free-tip rotor is shown to improve cruise L/DE by at least 22%.

Stroub, R. H.↗
NASA NTRS1981

Predesign study for a modern 4-bladed rotor for RSRA

The feasibility of providing a modern four-bladed rotor for flight research testing on a rotor system aircraft was evaluated. The capabilities of a state of the art rotor system and the contributions of key design parameters to these capabilities were investigated. Three candidate rotors were examined: the UH-60A BLACK HAWK rotor with and without root extenders and the H-3 composite blade rotor. It was concluded that the technical/cost objectives could best be accomplished using the basic BLACK HAWK rotor (i.e. without root extenders). Further, the availability of three existing sets of blade tip of varying design, together with a demonstrated capability for altering airfoil geometry should provide early research information on important design variables at reduced cost.

Davis, S. J.↗
NASA NTRS1982

Study of rotor gust response by means of the local momentum theory

The vertical gust response of the helicopter rotor in cruising flight is studied analytically by means of the local momentum theory (LMT) and experimentally in a wind tunnel utilizing a gust generator. By introducing the unsteady aerodynamic effects into the LMT and by considering the elastic deformation of the rotor blade, the vibratory characteristics of flapping blades and of the rotor forces can be obtained. Since the LMT makes it possible to calculate the instantaneous load distribution along the rotor blade in desired azimuthal or timewise intervals, the effects of gradual penetration of the rotor into the gust can be studied and the Fourier analysis or power spectrum analysis of the rotor response applied to any kind of gust input. Some results obtained analytically are verified by the experimental tests performed in the wind tunnel which generates step, sinusoidal and random vertical gusts by the motion of a series of cascaded vanes upstream of the rotor.

Azuma, A.↗