Results for “SPRAY NOZZLE” — Page 18

NASA NTRS1992

ASRM Process Development in Aqueous Cleaning

Viewgraphs are included on process development in aqueous cleaning which is taking place at the Aerojet Advanced Solid Rocket Motor (ASRM) Division under a NASA Marshall Space and Flight Center contract for design, development, test, and evaluation of the ASRM including new production facilities. The ASRM will utilize aqueous cleaning in several manufacturing process steps to clean case segments, nozzle metal components, and igniter closures. ASRM manufacturing process development is underway, including agent selection, agent characterization, subscale process optimization, bonding verification, and scale-up validation. Process parameters are currently being tested for optimization utilizing a Taguci Matrix, including agent concentration, cleaning solution temperature, agitation and immersion time, rinse water amount and temperature, and use/non-use of drying air. Based on results of process development testing to date, several observations are offered: aqueous cleaning appears effective for steels and SermeTel-coated metals in ASRM processing; aqueous cleaning agents may stain and/or attack bare aluminum metals to various extents; aqueous cleaning appears unsuitable for thermal sprayed aluminum-coated steel; aqueous cleaning appears to adequately remove a wide range of contaminants from flat metal surfaces, but supplementary assistance may be needed to remove clumps of tenacious contaminants embedded in holes, etc.; and hot rinse water appears to be beneficial to aid in drying of bare steel and retarding oxidation rate.

Swisher, Bill↗

NASA NTRS2008

Lagrangian Trajectory Modeling of Lunar Dust Particles

Apollo landing videos shot from inside the right LEM window, provide a quantitative measure of the characteristics and dynamics of the ejecta spray of lunar regolith particles beneath the Lander during the final 10 [m] or so of descent. Photogrammetry analysis gives an estimate of the thickness of the dust layer and angle of trajectory. In addition, Apollo landing video analysis divulges valuable information on the regolith ejecta interactions with lunar surface topography. For example, dense dust streaks are seen to originate at the outer rims of craters within a critical radius of the Lander during descent. The primary intent of this work was to develop a mathematical model and software implementation for the trajectory simulation of lunar dust particles acted on by gas jets originating from the nozzle of a lunar Lander, where the particle sizes typically range from 10 micron to 500 micron. The high temperature, supersonic jet of gas that is exhausted from a rocket engine can propel dust, soil, gravel, as well as small rocks to high velocities. The lunar vacuum allows ejected particles to travel great distances unimpeded, and in the case of smaller particles, escape velocities may be reached. The particle size distributions and kinetic energies of ejected particles can lead to damage to the landing spacecraft or to other hardware that has previously been deployed in the vicinity. Thus the primary motivation behind this work is to seek a better understanding for the purpose of modeling and predicting the behavior of regolith dust particle trajectories during powered rocket descent and ascent.

Lane, John E.↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

DOE OSTI2021

High Temperature Thermal Barrier Coating Evaluation of Yttrium Aluminum Garnet for Gas Turbine Applications

The Solution Precursor Spray Process (SPPS) process has been shown to overcome the durability and property challenges of applying yttrium aluminum garnet (YAG) coating for high temperature thermal barrier coating (TBC) applications (1200°C+) but only limited testing has been performed in representative application environments. In this study, YAG coatings were developed to optimize microstructure and tailor properties for combustion components in an industrial gas turbine. Thermal conductivity, erosion resistance and furnace cycling durability were used to validate YAG properties against the standard yttria-stabilized zirconia coating (YSZ). Graded and multi-layered microstructures were applied to enhance performance while maintaining durability. Further YAG process development was required to replicate coating properties and optimize deposition on more complex fuel injector nozzle and combustion liner components. Rig testing of both components was performed and compared against the baseline YSZ coating validating the high temperature capability and lower thermal conductivity of the SPPS YAG coating. The components in both tests were cycled for a minimum of ten cycles with the fuel injector test targeting a higher operating temperature while the combustor liner operated at standard conditions. A development engine test is planned to further validate performance in a gas turbine engine of this promising material.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Residual stress of controlled atmosphere plasma spray blended metal deposits measured via in-situ substrate curvature method

The preliminary use of the in-situ curvature measurement technique for analyzing the planar stress evolution of controlled atmosphere plasma spray (CAPS) refractory metal deposits was performed with SNL-NM org. 1834’s CAPS system. A porous refractory metal exemplar of Ta-Nb was sprayed onto Ni-200, Ti-6Al-4V, and Al 7075-T6 substrates using a constant plasma torch parameter setting and deposition toolpath. Residual stresses of the deposits were found to be largely influenced by the substrate coefficient of thermal expansion and were calculated to be 49, 90, and -136 MPa for Ni 200, Ti-6Al-4V, and Al 7075-T6, respectively. The “Evolving stress” of the Ta-Nb deposits, which more accurately describes the mean intrinsic splat quenching stress of the spray material during deposition, was calculated to be 67, 92, and 129 MPa for Ni-200, Ti-6Al-4V, and Al 7075-T6, respectively. Notable difference in curvature measurement for the 1st coating pass for the Al 7075- T6 substrate was observed, with interface micrograph evidence suggesting potential softening and/or melting of the Al 7075-T6 substrate surface during deposition. Substrate temperature measurements prior to Ta-Nb deposition were used to calculate thermal energy absorbed from the hot gas plume by the different substrates and were found to correlate to the substrate’s thermal effusively. These calculated thermal energies were also found to be ~10 to 15% of the calculated energy output from the plasma torch’s nozzle exit for these experimental conditions.

36 MATERIALS SCIENCE↗

NASA NTRS2005

Baseline Computational Fluid Dynamics Methodology for Longitudinal-Mode Liquid-Propellant Rocket Combustion Instability

A computational method for the analysis of longitudinal-mode liquid rocket combustion instability has been developed based on the unsteady, quasi-one-dimensional Euler equations where the combustion process source terms were introduced through the incorporation of a two-zone, linearized representation: (1) A two-parameter collapsed combustion zone at the injector face, and (2) a two-parameter distributed combustion zone based on a Lagrangian treatment of the propellant spray. The unsteady Euler equations in inhomogeneous form retain full hyperbolicity and are integrated implicitly in time using second-order, high-resolution, characteristic-based, flux-differencing spatial discretization with Roe-averaging of the Jacobian matrix. This method was initially validated against an analytical solution for nonreacting, isentropic duct acoustics with specified admittances at the inflow and outflow boundaries. For small amplitude perturbations, numerical predictions for the amplification coefficient and oscillation period were found to compare favorably with predictions from linearized small-disturbance theory as long as the grid exceeded a critical density (100 nodes/wavelength). The numerical methodology was then exercised on a generic combustor configuration using both collapsed and distributed combustion zone models with a short nozzle admittance approximation for the outflow boundary. In these cases, the response parameters were varied to determine stability limits defining resonant coupling onset.

Litchford, R. J.↗

NASA NTRS1996

Velocity and drop size measurements in a confined, swirl-stabilized, combusting spray

Drop size and velocity measurements in a confined, swirl-stabilized, reacting spray are presented. The configuration consisted of a center-mounted research air-assist atomizer surrounded by a coflowing air stream. A quartz tube surrounded the burner and provided the confinement. Both the air-assist and coflow streams had swirl imparted to them in the same direction with 45-degree-angle swirlers. The fuel and air entered the combustor at ambient temperature. The gas-phase measurements reported were obtained from the velocity drops with a mean diameter of four microns. Heptane fuel was used for all the experiments. Measurements of drop size and velocity, gas-phase velocity and drop number flux are reported for axial distances of 23, 5, 10, 15, 25, and 50 mm downstream of the nozzle. The measurements were performed using a two-component phase/Doppler particle analyzer. Profiles across the entire flowfield are presented.

Bulzan, Daniel L.↗

NASA NTRS1986

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗

NASA NTRS1986

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗

DOE OSTI2020

Influence of pilot-fuel mixing on the spatio-temporal progression of two-stage autoignition of diesel-sprays in low-reactivity ambient fuel-air mixture

The spatial and temporal locations of autoignition for direct-injection compression-ignition engines depend on fuel chemistry, temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into both fuel-chemistry and physical effects by varying fuel reactivities and engine operating conditions. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural-gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include high-speed (15kfps) cool-flame chemiluminescence-imaging as an indicator of low-temperature heat-release (LTHR) and OH* chemiluminescence-imaging as an indicator high-temperature heat-release (HTHR). NG prolongs the ignition delay of the pilot fuel and increases the combustion duration. Zero-dimensional chemical-kinetics simulations provide further understanding by replicating a Lagrangian perspective for mixtures evolving along streamlines originating either at the fuel nozzle or in the ambient gas, for which the pilot-fuel concentration is either decreasing or increasing, respectively. The zero-dimensional simulations predict that LTHR initiates most likely on the air streamlines before transitioning to HTHR, either on fuel-streamlines or on air-streamlines in regions of near-constant φ. Due to the relatively short pilot-fuel injection-durations, the transient increase in entrainment near the end of injection (entrainment wave) is important for quickly creating auto-ignitable mixtures. To achieve desired combustion characteristics, e.g., multiple ignition-kernels and favorable combustion phasing and location (e.g., for reducing wall heat-transfer or optimizing charge stratification), adjusting injection parameters could tailor mixing trajectories to offset changes in fuel ignition chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Enhanced energy conversion efficiency promoted by cavitation in gasoline direct injection

High-pressure direct fuel injection plays the most crucial role in energy conversion and improving engine combustion efficiency and emission. The optimization of turbulent and multiphase fuel injection has focused on controlling hydrodynamic parameters such as injection pressure. While the thermodynamic influence is often considered in the flash boiling situation, we inquire into how gasoline-type fuel’s hydro- and thermodynamic properties impact the injection dynamics by fuel-temperature induced cavitation. The turbulent and cavitating flows emanating from the direct-injection nozzle is visualized by ultrafast x-ray imaging with an unprecedented spatiotemporal resolution. The ultrafast liquid-fuel dynamics are dominated by injection pressure as well as fuel temperature through cavitation, an important thermodynamic parameter but often difficult to control in engine combustion. With the most direct and quantitative measurement, we discovered that the near-nozzle fuel-jet dynamics can be perfectly scaled by a single dimensionless parameter, cavitation number, particularly sensitive to the fuel temperature, in a wide operation range. This universal scaling shows that cavitation can be harnessed to elevate the pneumatic-hydraulic to kinetic energy conversion efficiency, critical for promoting fuel atomization and engine combustion performance. This enhancement effect will have even more impact on engine combustion using alternative low-emission fuels with higher saturated vapor pressure.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1993

Velocity and drop size measurements in a swirl-stabilized, combusting spray

Velocity and drop size measurements are reported for a swirl-stabilized, combusting spray. For the gas phase, three components of mean and fluctuating velocity are reported. For the droplets, three components of mean and fluctuating velocity, diameter, and number flux are reported. The liquid fuel utilized for all the tests was heptane. The fuel was injected using an air-assist atomizer. The combustor configuration consisted of a center-mounted, air-assist atomizer surrounded by a coflowing air stream. Both the coflow and the atomizing air streams were passed through 45 degree swirlers. The swirl was imparted to both streams in the same direction. The combustion occurred unconfined in stagnant surroundings. The nonintrusive measurements were obtained using a two-component phase/Doppler particle analyzer. The laser-based instrument measured two components of velocity as well as droplet size at a particular point. Gas phase measurements were obtained by seeding the air streams with nominal 1 micron size aluminum-oxide particles and using the measured velocity from that size to represent the gas phase velocity. The atomizing air, coflow air, and ambient surroundings were all seeded with the aluminum-oxide particles to prevent biasing. Measurements are reported at an axial distance of 5 mm from the nozzle. Isothermal single-phase gas velocities are also reported for comparison with the combusting case.

Bulzan, Daniel L.↗

DOE OSTI2023

A sui generis whipping-instability-based self-sequencing multi-monodisperse 2D spray from an anisotropic microfluidic liquid jet device

Well-defined aerosols pave the way for versatile basic and applied research. Here, we demonstrate a unique whipping instability that generates from a high-aspect-ratio microfluidic device resulting in a unique steady-state gas-focused whipping jet (WJ) without any need for electrification. This WJ device emanates a multi-monodisperse whipping spray jet with a two-dimensional (2D) profile. We demonstrate this phenomenon based on various fluidic parameters theoretically and experimentally. The 2D WJ’s unique behavior is derived using analytical fluid dynamics to explain jet diameter, whipping regime, and spreading angle. The phenomenon is further characterized experimentally by measuring the angle with respect to the flow rate, the distances between droplets, the droplet shapes, and the reproducibility of these parameters. We also explain the precise fabrication of such inexpensive devices. Lastly, we highlight these devices’ potential use as sample environments in versatile applications ranging from cryoelectron microscopy over mass spectrometry to drug formulation and structural studies at X-ray free-electron lasers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2010

NASA Tech Briefs, May 2010

Topics covered include: Instrument for Analysis of Greenland's Glacier Mills Cryogenic Moisture Apparatus; A Transportable Gravity Gradiometer Based on Atom Interferometry; Three Methods of Detection of Hydrazines; Crossed, Small-Deflection Energy Analyzer for Wind/Temperature Spectrometer; Wavefront Correction for Large, Flexible Antenna Reflector; Novel Micro Strip-to-Waveguide Feed Employing a Double-Y Junction; Thin-Film Ferro Electric-Coupled Microstripline Phase Shifters With Reduced Device Hysteresis; Two-Stage, 90-GHz, Low-Noise Amplifier; A 311-GHz Fundamental Oscillator Using InP HBT Technology; FPGA Coprocessor Design for an Onboard Multi-Angle Spectro-Polarimetric Imager; Serrating Nozzle Surfaces for Complete Transfer of Droplets; Turbomolecular Pumps for Holding Gases in Open Containers; Triaxial Swirl Injector Element for Liquid-Fueled Engines; Integrated Budget Office Toolbox; PLOT3D Export Tool for Tecplot; Math Description Engine Software Development Kit; Astronaut Office Scheduling System Software; ISS Solar Array Management; Probabilistic Structural Analysis Program; SPOT Program; Integrated Hybrid System Architecture for Risk Analysis; System for Packaging Planetary Samples for Return to Earth; Offset Compound Gear Drive; Low-Dead-Volume Inlet for Vacuum Chamber; Simple Check Valves for Microfluidic Devices; A Capillary-Based Static Phase Separator for Highly Variable Wetting Conditions; Gimballing Spacecraft Thruster; Finned Carbon-Carbon Heat Pipe with Potassium Working Fluid; Lightweight Heat Pipes Made from Magnesium; Ceramic Rail-Race Ball Bearings; Improved OTEC System for a Submarine Robot; Reflector Surface Error Compensation in Dual-Reflector Antennas; Enriched Storable Oxidizers for Rocket Engines; Planar Submillimeter-Wave Mixer Technology with Integrated Antenna; Widely Tunable Mode-Hop-Free External-Cavity Quantum Cascade Laser; Non-Geiger-Mode Single-Photon Avalanche Detector with Low Excess Noise; Using Whispering-Gallery-Mode Resonators for Refractometry; RF Device for Acquiring Images of the Human Body; Reactive Collision Avoidance Algorithm; Fast Solution in Sparse LDA for Binary Classification; Modeling Common-Sense Decisions in Artificial Intelligence; Graph-Based Path-Planning for Titan Balloons; Nanolaminate Membranes as Cylindrical Telescope Reflectors; Air-Sea Spray Airborne Radar Profiler Characterizes Energy Fluxes in Hurricanes; Large Telescope Segmented Primary Mirror Alignment; and Simplified Night Sky Display System.

Source record↗

NASA NTRS2003

High-Temperature Sprayable Phosphor Coating Developed for Measuring Surface Temperatures

The use of phosphor thermography for noncontact temperature measurements in harsh environments has been proven over the last decade, but it has suffered from difficult application procedures such as vapor deposition or sputtering techniques. We have developed a high-temperature-sensitive paint that is easily applied with commercially available paint-spraying equipment and have successfully demonstrated it to temperatures up to 1500 C. Selected phosphors have also shown measurable signals to 1700 C, thus allowing a combination of phosphors to be used in high-temperature binders to make surface temperature measurements from ambient to over 1500 C. Phosphor thermography is an optical technique that measures the time response of fluorescence light, which is a function of the phosphor temperature. The phosphors are excited with short wavelength light (ultraviolet or blue), and they emit light at a longer wavelength. This technique has a benefit over other temperature measurements, such as thermocouples and infrared thermography, in difficult environments such as high blackbody backgrounds, vibration, flames, high electromagnetic noise, or where special windows may be needed. In addition, the sprayable phosphor paints easily cover large or complicated structures, providing full-surface information with a single measurement. Oak Ridge National Laboratories developed and tested the high-temperature binders and phosphors under the direction of the NASA Glenn Research Center. Refractory materials doped with rare earth metals were selected for their performance at high temperature. Survivability, adhesion, and material compatibility tests were conducted at high temperatures in a small furnace while the fluorescent response from the phosphors was being measured. A painted sample in a furnace with a clearly visible fluorescing dot excited by a pulsed laser is shown. Measuring the decay time of this fluorescence yields the surface temperature. One new paint was recently tested in a rocket test stand at Glenn. The floor of a square duct nozzle was painted, and full-field lifetime decay measurements were acquired for multiple firings of the rocket. Good agreement with predicted results was obtained, matching temperature gradients along the length of the nozzle and clearly showing shock structures. These good results were very satisfactory given that the measurements were made looking through the combustion plume. Infrared pyrometry was incapable of making the surface measurements because of the interference from the rocket exhaust, which contaminated the infrared signature.

Bencic, Timothy J.↗

DOE OSTI2022

Experimental Investigation of Cavitation-Induced Erosion Using X-Ray Imaging and Tomography

High injection pressure in diesel engines can lead to cavitation-induced erosion in injector nozzles. One important factor affecting the severity of erosion is the fuel and its properties. Traditionally, modeling and simulation studies have used single-component representations of fuels, but realistic fuels feature a multitude of components and can even include volatile additives such as water and alcohol. To provide realistic benchmarks and comparisons, experimental measurements quantifying erosion characteristics were made using ultra-low sulfur diesel (ULSD) and two alternative diesel fuels (ADF). X-ray imaging and computed tomography were used to investigate cavitation-induced erosion onset and progression. Hard X-ray tomography revealed injector internal geometry, including details such as surface marks from the manufacturing process and erosion patterns from repeated injections. Erosion progression was measured using X-ray tomography and imaging performed between injections. The critical erosion site was found to be similar across different fuel blends, while the erosion rate and incubation time were sensitive to the fuel blend. The injector geometry and the erosion characteristics were also prepared for numerical model development and validation.

42 ENGINEERING↗