Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Alleviation of side force on tangent-ogive forebodies using passive porosity

An experimental investigation to determine the effectiveness of porosity for alleviating side forces on forebodies was conducted in the NASA Langley Research Center 7 x 10 ft High-Speed Wind Tunnel. The study consisted of a comparison of experimental force, moment, and surface pressure results obtained on a fineness ratio 5.0 tangent-ogive porous forebody with 0.020 in. hole diameter and 22 percent porosity with results obtained on a solid forebody. The forebodies were tested with cylindrical afterbodies. The solid forebody was tested with transition grit to simulate fully turbulent conditions and without transition grit to simulate free transition conditions. The extent of porosity on the forebody was varied to determine the extent of porosity needed to alleviate side forces. Static longitudinal and lateral-directional stability and surface pressure data were obtained at Mach numbers of 0.2, 0.5, and 0.8. The angle of attack range was from 5 to 45 deg and roll angles from -90 to 180 deg. The solid forebody exhibited large asymmetries at moderate to high angles of attack causing large side forces and yawing moments. The porous forebody exhibited no significant side forces or yawing moments at any angle of attack tested.

Bauer, Steven X. S.↗
NASA NTRS1992

Correlation of forebody pressures and aircraft yawing moments on the X-29A aircraft at high angles of attack

In-flight pressure distributions at four fuselage stations on the forebody of the X-29A aircraft have been reported at angles of attack from 15 to 66 deg and at Mach numbers from 0.22 to 0.60. At angles of attack of 20 deg and higher, vortices shed from the nose strake caused suction peaks in the pressure distributions that generally increased in magnitude with angle of attack. Above 30 deg-angle of attack, the forebody pressure distributions became asymmetrical at the most forward station, while they remained nearly symmetrical until 50 to 55 deg-angle of attack for the aft stations. Between 59 to 66 deg-angle of attack, the asymmetry of the pressure distributions changed direction. Yawing moments for the forebody alone were obtained by integrating the forebody pressure distributions. At 45 deg-angle of attack, the aircraft yaws to the right and at 50 deg and higher, the aircraft yaws to the left. The forebody yawing moments correlated well with the aircraft left yawing moment at an angle of attack of 50 deg or higher. At a 45 deg-angle of attack, the forebody yawing moments did not correlate well with the aircraft yawing moment, but it is suggested that this was due to asymmetric pressures on the cockpit region of the fuselage which was not instrumented. The forebody was also shown to provide a positive component of directional stability of the aircraft at angles of attack of 25 deg or higher. A Mach number effect was noted at angles of attack of 30 deg or higher at the station where the nose strake was present. At this station, the suction peaks in the pressure distributions at the highest Mach number were reduced and much more symmetrical as compared to the lower Mach number pressure distributions.

Fisher, David F.↗
NASA NTRS1992

In-flight flow visualization results from the X-29A aircraft at high angles of attack

Flow visualization techniques were used on the X-29A aircraft at high angles of attack to study the vortical flow off the forebody and the surface flow on the wing and tail. The forebody vortex system was studied because asymmetries in the vortex system were suspected of inducing uncommanded yawing moments at zero sideslip. Smoke enabled visualization of the vortex system and correlation of its orientation with flight yawing moment data. Good agreement was found between vortex system asymmetries and the occurrence of yawing moments. Surface flow on the forward-swept wing of the X-29A was studied using tufts and flow cones. As angle of attack increased, separated flow initiated at the root and spread outboard encompassing the full wing by 30 deg angle of attack. In general, the progression of the separated flow correlated well with subscale model lift data. Surface flow on the vertical tail was also studied using tufts and flow cones. As angle of attack increased, separated flow initiated at the root and spread upward. The area of separated flow on the vertical tail at angles of attack greater than 20 deg correlated well with the marked decrease in aircraft directional stability.

Delfrate, John H.↗
NASA NTRS1993

Subsonic aerodynamic characteristics of a proposed advanced manned launch system orbiter configuration

The Advanced Manned Launch System is a proposed near-term technology, two-stage, fully reusable launch system that consists of an unmanned glide-back booster and a manned orbiter. An orbiter model that featured a large fuselage and an aft delta wing with tip fins was tested in the Langley 7- by 10-Foot High-Speed Tunnel. A crew cabin, large payload fairing, and crew access tunnel were mounted on the upper body. The results of the investigation indicated that the configuration was longitudinally stable to an angle of attack of about 6 deg about a center-of-gravity position of 0.7 body length. The model had an untrimmed lift-drag ratio of 6.6, but could not be trimmed at positive lift. The orbiter model was also directionally unstable. The payload fairing was responsible for about half the instability. The tip-fin controllers, which are designed as active controls to produce artificial directional stability, were effective in producing yawing moment, but sizable adverse rolling moment occurred at angles of attack above 6 deg. Differential deflection of the elevon surfaces was effective in producing rolling moment with only small values of adverse yawing moment.

Ware, George M.↗
NASA NTRS1992

In-Flight Flow Visualization Results From the X-29A Aircraft at High Angles of Attack

Flow visualization techniques were used on the X-29A aircraft at high angles of attack to study the vortical flow off the forebody and the surface flow on the wing and tail. The forebody vortex system was studied because asymmetries in the vortex system were suspected of inducing uncommanded yawing moments at zero sideslip. Smoke enabled visualization of the vortex system and correlation of its orientation with flight yawing moment data. Good agreement was found between vortex system asymmetries and the occurrence of yawing moments. Surface flow on the forward-swept wing of the X-29A was studied using tufts and flow cones. As angle of attack increased, separated flow initiated at the root and spread outboard encompassing the full wing by 30° angle of attack. In general, the progression of the separated flow correlated well with subscale model lift data. Surface flow on the vertical tail was also studied using tufts and flow cones. As angle of attack increased, separated flow initiated at the root and spread upward. The area of separated flow on the vertical tail at angles of attack ≥ 20° correlated well with the marked decrease in aircraft directional stability.

Flight Testing↗
NASA NTRS1992

Correlation of Forebody Pressures and Aircraft Yawing Moments on the X-29A Aircraft at High Angles of Attack

In-flight pressure distributions at four fuselage stations on the forebody of the X-29A aircraft have been reported at angles of attack from 15 to 66° and at Mach numbers from 0.22 to 0.60. At angles of attack of 20° and higher, vortices shed from the nose strake caused suction peaks in the pressure distributions that generally increased in magnitude with angle of attack. Above 30° -angle of attack, the fore body pressure distributions became asymmetrical at the most forward station, while they remained nearly symmetrical until 50- to 55°-angle of attack for the aft stations. Between 59- to 66°-angle of attack, the asymmetry of the pressure distributions changed direction. Yawing moments for the forebody alone were obtained by integrating the forebody pressure distributions. At 45°-angle of attack, the aircraft yaws to the right and at 50° and higher, the aircraft yaws to the left. The fore body yawing moments correlated well with the aircraft left yawing moment at an angle of attack of 50° or higher. At a 45°-angle of attack, the forebody yawing moments did not correlate well with the aircraft yawing moment, but it is suggested that this was due to asymmetric pressures on the cockpit region of the fuselage which was not instrumented. The forebody was also shown to provide a positive component of directional stability of the aircraft at angles of attack of 25° or higher. A Mach number effect was noted at angles of attack of 30° or higher at the station where the nose strake was present. At this station, the suction peaks in the pressure distributions at the highest Mach number were reduced and much more symmetrical as compared to the lower Mach number pressure distributions.

Flight Testing↗
NASA NTRS1938

The estimation of the rate of change of yawing moment with sideslip

Wind-tunnel data are presented on the rate of change of yawing moment with sideslip for tests of 9 complete airplane models, 20 fuselage shapes, and 3 wing models with various combinations of dihedral, sweepback, and twist. The data were collected during a survey of existing information, which was made to find a reliable method of computing the yawing moment due to sideslip. Important errors common to methods of computation used at present appear to be due to large interference effects, the investigation of which will undoubtedly require an extensive program of systematic wind-tunnel tests. At present it is necessary to place considerable reliance on past design experience in proportioning an airplane so as to obtain a reasonable degree of directional stability.

Imlay, Frederick H↗
NASA NTRS1953

Some Effects of Frequency on the Contribution of a Vertical Tail to the Free Aerodynamic Damping of a Model Oscillating in Yaw

The damping in yaw and the directional stability of a model freely oscillating in yaw were measured tail-off and tail-on and compared with the values obtained by theoretical consideration of the unsteady lift associated with an oscillating vertical tail. A range of low frequencies comparable to those of the lateral motions of airplanes was covered. The analysis includes the effects of vertical-tail aspect ratio and the two-dimensional effects of compressibility.

Bird, John D↗
NASA NTRS1994

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Ware, George M.↗
NASA NTRS1993

Experimental investigation of advanced hub and pylon fairing configurations to reduce helicopter drag

New hub and pylon fairing designs were tested on a one-fifth scale Bell Helicopter Textron Model 222 helicopter with a bearingless main rotor hub. The blades were not installed for this test. The fairings were designed by NASA and Bell Helicopter Textron under a joint program and tested in the Ames Research Center 7-by 10-Foot Wind Tunnel. All six aircraft forces and moments were measured using the tunnel scales system. Previous research has identified the integrated hub and pylon fairing approach as the most efficient in reducing helicopter drag. Three hub fairings and three pylon fairings were tested (in various combinations) resulting in a total of 16 different configurations, including the baseline helicopter model without fairings. The geometry of the new fairings is described in detail. Test results are presented in the form of plots of the six model forces and moments. The data show that model drag can be reduced by as much as 20 percent by combining a small hub fairing (that has a circular arc upper surface and a flat lower surface) integrated with a nontapered pylon fairing. To minimize drag, the gap between the lower surface of the hub and upper surface of the pylon fairing must be kept to a minimum. Results show that the aerodynamic effects of the fairings on static longitudinal and directional stability can also be important.

Martin, D. M.↗
NASA NTRS1996

Effects of Winglets on the Drag of a Low-Aspect-Ratio Configuration

A wind-tunnel investigation has been performed to determine the effect of winglets on the induced drag of a low-aspect-ratio wing configuration at Mach numbers between 0.30 and 0.85 and a nominal angle-of-attack range from -2 deg to 20 deg. Results of the tests at the cruise lift coefficient showed significant increases in lift-drag ratio for the winglet configuration relative to a wing-alone configuration designed for the same lift coefficient and Mach number. Further, even larger increases in lift-drag ratio were observed at lift coefficients above the design value at all Mach numbers tested. The addition of these winglets had a negligible effect on the static lateral-directional stability characteristics of the configuration. No tests were made to determine the effect of these winglets at supersonic Mach numbers, where increases in drag caused by winglets might be more significant. Computational analyses were also performed for the two configurations studied. Linear and small-disturbance formulations were used. The codes were found to give reasonable performance estimates sufficient for predicting changes of this magnitude.

Smith, Leigh Ann↗
NASA NTRS1996

Wind-tunnel development of an SR-71 aerospike rocket flight test configuration

A flight experiment has been proposed to investigate the performance of an aerospike rocket motor installed in a lifting body configuration. An SR-71 airplane would be used to carry the aerospike configuration to the desired flight test conditions. Wind-tunnel tests were completed on a 4-percent scale SR-71 airplane with the aerospike pod mounted in various locations on the upper fuselage. Testing was accomplished using sting and blade mounts from Mach 0.6 to Mach 3.2. Initial test objectives included assessing transonic drag and supersonic lateral-directional stability and control. During these tests, flight simulations were run with wind-tunnel data to assess the acceptability of the configurations. Early testing demonstrated that the initial configuration with the aerospike pod near the SR-71 center of gravity was unsuitable because of large nosedown pitching moments at transonic speeds. The excessive trim drag resulting from accommodating this pitching moment far exceeded the excess thrust capability of the airplane. Wind-tunnel testing continued in an attempt to find a configuration suitable for flight test. Multiple configurations were tested. Results indicate that an aft-mounted model configuration possessed acceptable performance, stability, and control characteristics.

Smith, Stephen C.↗
NASA NTRS1996

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Lepsch, Roger A., Jr.↗
NASA NTRS1959

Measurements Obtained During the First Landing of the North American X-15 Research Airplane

The first landing of the X-15 airplane was made at 8:43 a.m., June 8, 1959, on the hard surface of Rogers Dry Lake. One purpose of the first-glide flight was to evaluate the effectiveness of the landing-gear system. Some results are presented of the landing-approach characteristics, the impact period, and the runout phase of the landing maneuver. The results indicate that the touchdown was accomplished at a vertical velocity of 2.0 feet per second for the main gear and 13.5 feet per second for the nose gear. These vertical velocities were within the values of sinking speeds established by structural design limitations. However, permanent structural deformation occurred in the main-landing-gear system as a result of the landing, and a reevaluation of the gear is being made by the manufacturer. The landing occurred at a true ground speed of 158 knots for main-gear touchdown at an angle of attack of 8.50. The incremental acceleration at the main gear was 2.7g and 7.39 at the nose gear as a result of the landing. The incremental acceleration at the center of gravity of the airplane was 0.6g for the main-gear impact and 2.4g for the nose-gear impact. The incremental acceleration at the main gear as a result of the nose-gear impact was 4.8g. The extreme rearward location of the main-gear skids appears to offer satisfactory directional stability characteristics during the run- out phase of the landing. No evidence of nosewheel shimmy was indicated during the impact and runout phase of the landing despite the absence of a shimmy damper on the nose gear. The maximum amount of skid wear as a result of the landing was on the order of 0.005 inch. No appreciable amount of tire wear was indicated for the dual, corotating nosewheels.

McKay, James M.↗
NASA NTRS1959

Launch, Low-Speed, and Landing Characteristics Determined from the First Flight of the North American X-15 Research Airplane

The first flight of the North American X-15 research airplane was made on June 8, 1959. This was accomplished after completion of a series of captive flights with the X-15 attached to the B-52 carrier airplane to demonstrate the aerodynamic and systems compatibility of the X-15//B-52 combination and the X-15 subsystem operation. This flight was planned as a glide flight so that the pilot need not be concerned with the propulsion system. Discussions of the launch, low-speed maneuvering, and landing characteristics are presented, and the results are compared with predictions from preflight studies. The launch characteristics were generally satisfactory, and the X-15 vertical tail adequately cleared the B-52 wing cutout. The actual landing pattern and landing characteristics compared favorably with predictions, and the recommended landing technique of lowering the flaps and landing gear at a low altitude appears to be a satisfactory method of landing the X-15 airplane. There was a quantitative correlation between flight-measured and predicted lift-drag-ratio characteristics in the clean configuration and a qualitative correlation in the landing configuration. A longitudinal-controllability problem, which became severe in the landing configuration, was evident throughout the flight and, apparently, was aggravated by the sensitivity of the side-located control stick. In the low-to-moderate angle-of-attack range covered, the longitudinal and directional stability were indicated to be adequate.

Finch, Thomas W.↗
NASA NTRS1999

An Experimental Database for Conventional and Alternate Control Concepts on the HSR 1.675% Reference H Model

The objective was to experimentally evaluate the longitudinal and lateral-directional stability and control characteristics of the Reference H configuration at supersonic and transonic speeds. A series of conventional and alternate control devices were also evaluated at supersonic and transonic speeds. A database on the conventional and alternate control devices was to be created for use in the HSR program.

McMillin, Naomi↗
NASA NTRS1949

A Preliminary Analysis of the Flying Qualities of the Consolidated Vultee MX-813 Delta-Wing Airplane Configuration at Transonic and Low Supersonic Speeds as Determined from Flights of Rocket-Powered Models

A preliminary analysis of the flying qualities of the Consolidated Vultee MX-813 delta-wing airplane configuration has been made based on the results obtained from the first two 1/8 scale models flown at the NACA Pilotless Aircraft Research Station, Wallop's Island, VA. The Mach number range covered in the tests was from 0.9 to 1.2. The analysis indicates adequate elevator control for trim in level flight over the speed range investigated. Through the transonic range there is a mild trim change with a slight tucking-under tendency. The elevator control effectiveness in the supersonic range is reduced to about one-half the subsonic value although sufficient control for maneuvering is available as indicated by the fact that 10 deg elevator deflection produced 5g acceleration at Mach number of 1.2 at 40,000 feet.The elevator control forces are high and indicate the power required of the boost system. The damping. of the short-period oscillation is adequate at sea-level but is reduced at 40,000 feet. The directional stability appears adequate for the speed range and angles of attack covered.

Mitcham, Grady L.↗