Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, LATERAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Tradeoff studies in multiobjective insensitive design of airplane control systems

A computer aided design method for multiobjective parameter-insensitive design of airplane control systems is described. Methods are presented for trading off nominal values of design objectives against sensitivities of the design objectives to parameter uncertainties, together with guidelines for designer utilization of the methods. The methods are illustrated by application to the design of a lateral stability augmentation system for two supersonic flight conditions of the Shuttle Orbiter. Objective functions are conventional handling quality measures and peak magnitudes of control deflections and rates. The uncertain parameters are assumed Gaussian, and numerical approximations of the stochastic behavior of the objectives are described. Results of applying the tradeoff methods to this example show that stochastic-insensitive designs are distinctly different from deterministic multiobjective designs. The main penalty for achieving significant decrease in sensitivity is decreased speed of response for the nominal system.

Schy, A. A.↗
NASA NTRS1983

Exploratory low-speed wind-tunnel investigation of advanced commuter configurations including an over-the-wing propeller design

A recent low-speed wind-tunnel investigation of a three-surface regional transport configuration has shown large favorable power effects on longitudinal and lateral stability and marginal engine-out trim characteristics for some aft engine and empennage configurations. The present paper discusses these results in terms of static force test information obtained for power-off and power-on conditions. Also discussed in this paper are wind-tunnel results which indicate that mounting propellers over the wing can introduce large favorable slipstream interference effects which significantly reduce the wing drag at climb power conditions.

Johnson, J. L., Jr.↗
NASA NTRS1986

Adapted head- and eye-movement responses to added-head inertia

Adaptation to inertia added to the head was studied in men by mounting masses on a rigidly attached helmet until two- to ten-fold increases of inertia were produced, while an overhead suspension compensated for the weights. The observed changes in the eye and head movement coordination included increased head movement latencies, as well as changes in the eye movement amplitude, and later stabilizing alternate contractions of the neck muscles. Oscillopsia, or continual displacement or instability of the visual world, which is a symptom of a breakdown of space constancy, was prominent and consistent in the perceptual reports of the subjects. Although adaptation resulting from adding inertia to the head occurred much faster than that induced by adding prisms or lenses, it has similar perceptual and motor components that may be objectively studied in detail.

Gauthier, G. M.↗
NASA NTRS1984

Tradeoff methods in multiobjective insensitive design of airplane control systems

The latest results of an ongoing study of computer-aided design of airplane control systems are given. Constrained minimization algorithms are used, with the design objectives in the constraint vector. The concept of Pareto optimiality is briefly reviewed. It is shown how an experienced designer can use it to find designs which are well-balanced in all objectives. Then the problem of finding designs which are insensitive to uncertainty in system parameters are discussed, introducing a probabilistic vector definition of sensitivity which is consistent with the deterministic Pareto optimal problem. Insensitivity is important in any practical design, but it is particularly important in the design of feedback control systems, since it is considered to be the most important distinctive property of feedback control. Methods of tradeoff between deterministic and stochastic-insensitive (SI) design are described, and tradeoff design results are presented for the example of the a Shuttle lateral stability augmentation system. This example is used because careful studies have been made of the uncertainty in Shuttle aerodynamics. Finally, since accurate statistics of uncertain parameters are usually not available, the effects of crude statistical models on SI designs are examined.

Schy, A. A.↗
NASA NTRS1987

Grabber arm mechanism for the Italian Research Interim Stage (IRIS)

Two deployable arms, named grabbers, were designed and manufactured to provide lateral stability of the perigee spinning stage which will be deployed from the Space Shuttle cargo bay. The spinning stage is supported by a spin table on a cradle at its base. The Italian Research Interim Stage (IRIS) is designed to carry satellites of intermediate mass up to 900 kg. The requirements are defined and the mechanism is described. Functional test results are presented.

Turci, Edmondo↗
NASA NTRS1988

Experimental investigation of non-planar sheared outboard wing planforms

The outboard planforms of wings have been found to be of prime importance in studies of induced drag reduction. This conclusion is based on an experimental and theoretical study of the aerodynamic characteristics of planar and nonplanar outboard wing forms. Six different configurations; baseline rectangular, planar sheared, sheared with dihedral, sheared with anhedral, rising arc, and drooping arc were investigated for two different spans. Span efficiencies as much as 20 percent greater than baseline can be realized with nonplanar wing forms. Optimization studies show that this advantage can be achieved along with a bending moment benefit. Parasite drag and lateral stability estimations were not included in the analysis.

Naik, D. A.↗
NASA NTRS1989

Transonic aerodynamic characteristics of a proposed Assured Crew Return Capability (ACRC) lifting-body configuration

The investigation was conducted in the Calspan 8-Ft Transonic wind tunnel at Mach numbers from 0.6 to 1.2. The 0.07-scale model had a low aspect ratio body with a flat undersurface. A center fin and two tip fins were mounted on the aft upper body. The tip fins were rolled outboard 40 deg from the vertical. Elevon surfaces made up the trailing edges of the outboard fins and body flaps were located on the upper and lower aft fuselage. Results of the investigation indicated that the model was longitudinally and laterally stable about a center-of-gravity position of 0.54 body length. The maximum trimmed lift-drag ratio was about 3.1 at M = 0.6. The small center fin contributed only a small positive increment to lateral stability but was effective as a yaw control device. Protuberances on the forebody had little effect on the aerodynamic characteristics of the configuration. The model with pitch controls undeflected had desirable longitudinal trim characteristics.

Ware, George M.↗
NASA NTRS1990

Project Dawdler: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

In direct response to Request for Proposals: Flight at very low Reynolds numbers - a station keeping mission, the members of Design Squad E present Project Dawdler: a remotely-piloted airplane supported by an independently controlled take-off cart. A brief introduction to Project Dawdler's overall mission and design, is given. The Dawdler is a remotely-piloted airplane designed to fly in an environmentally-controlled closed course at a Reynolds number of 10(exp 5) and at a cruise velocity of 25 ft/s. The two primary goals were to minimize the flight Reynolds number and to maximize the loiter time. With this in mind, the general design of the airplane was guided by the belief that a relatively light aircraft producing a fairly large amount of lift would be the best approach. For this reason the Dawdler utilizes a canard rather than a conventional tail for longitudinal control, primarily because the canard contributes a positive lift component. The Dawdler also has a single vertical tail mounted behind the wing for lateral stability, half of which is used as a rudder for yaw control. Due to the fact that the power required to take-off and climb to altitude is much greater than that required for cruise flight and simple turning maneuvers, it was decided that a take-off cart be used. Based on the current design, there are two unknowns which could possibly threaten the success of Project Dawdler. First, the effect of the fully-movable canard with its large appropriation of total lift on the performance of the plane, and secondly, the ability of the take-off procedure to go as planned are examined. These are questions which can only be answered by a prototype.

Bartilotti, Rich↗
NASA NTRS1989

Investigations of modifications to improve the spin resistance of a high-wing, single-engine, light airplane

A general aviation aircraft with drooped leading edge modifications for improvement of lateral stability at high angles of attack has been flight tested in combination with a ventral fin which improves directional stability. The two modifications were assessed in light of spin-resistance criteria proposed for incorporation into FAA certification regulations. The configuration combining outboard wing leading-edge droop and a ventral fin yielded a substantial increase in spin resistance, but fell short of all requirements encompassed by the proposed spin-resistance criteria.

Manuel, G. S.↗
NASA NTRS1991

Final design proposal: Zeta group-Valkyrie. A proposal in response to a commercial air transportation study

The Valkyrie flying wing concept is a remotely piloted technology demonstrator designed to serve as a high volume commuter transport in Aeroworld. The 5.02 lb Valkyrie has a planform area of 1440 sq in and a wingspan of 84 in, which results in an aspect ratio of 4.9. The Valkyrie uses the NACA 2R(2)12 airfoil section. A leading edge wing sweep of 13.2 deg and a 2 deg dihedral were incorporated to provide lateral stability. The Valkyrie is semi-monocoque structure manufactured from spruce and balsa wood covered in plastic Mylar skin. The AstroFlight Cobolt 25 electric engine will power the Valkyrie with a Tornado 10-6 propeller. The Valkyrie is designed to take off in less than 20 ft. To eliminate the difficulties associated with rotating the aircraft at takeoff, the wing is mounted on its landing gear at the take off angle of attack of 8 deg. The Valkyrie provides a greater payload to weight ratio than a conventionally configured aircraft of comparable weight. Considering the requirements, the Valkyrie is the most efficient design for the specified mission.

Source record↗
NASA NTRS1992

Laboratory evaluation of footings for lunar telescopes

Presented here are the results of laboratory experiments with diffferent footing shapes for lunar telescopes. These experiments used a variety of soils including some to simulate regolith response. Based on what is known of regolith and regolith-structure interaction, a shallow-multiple-contact points footing foundation can be adequately designed to support lunar telescopes. Plane-strain load-displacement tests were conducted with different footings and different lunar simulants in a deep transparent plexiglass container. The model footings considered include the rectangular, hemispherical, and spudcan designs. Simulants used to reproduce the mechanical properties of the lunar regolith were fly ash, crushed basalt with and without glass, and a processed lunar simulant. Load-displacement curves were obtained for the different footings in Ottawa sand and in the crushed basalt with glass. The spudcan footing was found to be self-digging and yet stiff, thus providing excellent lateral stability in a large variety of soils.

Chua, Koon M.↗
NASA NTRS1930

Span Load Distribution on Two Monoplanes Wing Models as Affected by Twist and Sweepback

The results presented in this note show the effect of twist and sweepback on the span load distribution over two monoplane wing models. The tests were made in the Atmospheric Wind Tunnel of the Langley Memorial Aeronautical Laboratory. The data are taken from the results of an investigation dealing primarily with lateral stability. As presented, they are suitable as an aid in the structural design of certain monoplane wings.

Knight, Montgomery↗
NASA NTRS1933

Wind tunnel research concerning lateral control devices, particularly at high angles of attack VII : Handley Page tip and full-span slots with ailerons and spoilers

Tests were made with ordinary ailerons and different sizes of spoilers on rectangular Clark Y wing models with Handley Page tip and full span slots. The tests showed the effect of the control devices on the general performance of the wings as well as on the lateral control and lateral stability characteristics.

Weick, Fred E↗
NASA NTRS1938

The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J

The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.

House, R O↗
NASA NTRS1947

Wind-tunnel investigation of the effect of power and flaps on the static lateral characteristics of a single-engine low-wing airplane model

Tests were made in the Langley 7- by 10-foot tunnel to determine the lateral-stability characteristics with and without power of a model of a typical low-wing single-engine airplane with flaps neutral, with a full-span single slotted flap, and with a full-span double slotted flap. Power decreased the dihedral effect regardless of flap condition, and the double-slotted flap configuration showed the most marked decrease. The usual effect of power in increasing the directional stability was also shown. Deflection of the single slotted flap produced negative dihedral effect, but increased the directional stability. The effects of deflecting the double slotted flap were erratic and marked changes in both effective dihedral and directional stability occurred. The addition of the tail surfaces always contributed directional stability and generally produced positive dihedral effect.

Tamburello, Vito↗
NASA NTRS1952

Aerodynamic Characteristics of a Refined Deep-step Planing-tail Flying-boat Hull with Various Forebody and Afterbody Shapes

An investigation was made in the Langley 300-mph 7- by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes and, for comparison, a streamline body simulating the fuselage of a modern transport airplane. The results of the tests indicated that the configurations incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the configurations incorporating a forebody with length-beam ratio of 5. The lowest minimum drag coefficients, which were considerably less than that of a conventional hull and slightly less than that of a streamline body, were obtained on the length-beam-ratio-7 forebody, alone and with round center boom. Drag coefficients and longitudinal- and lateral-stability parameters presented include the interference of a 21-percent-thick support wing.

SEAPLANES - GENERAL STUDIES↗
NASA NTRS1935

Wind-tunnel Tests of a Wing with a Trailing-edge Auxiliary Airfoil Used as a Flap

This report gives the characteristics of a wing with an auxiliary airfoil mounted near its trailing edge and used as a flap. The tests were made with a 10 by 60 inch Clark Y main airfoil and an NACA 0012 flap having a chord equal to 15 percent of the main wing chord. The axis of the flap in all cases was on the flap chord and 20 percent back from its leading edge. The optimum location of the flap axis relative to the main wing for maximum lift was found to be 1.25 percent of the main wing chord behind the trailing edge and 2.5 percent below the chord. In this position C(sub L max) was increased from 1.250 (for the plain wing) to 1.810 at 45 degrees deflection of the flap and C(sub D min) was decreased form 0.0155 to 0.0146 at minus 5 degrees deflection, the coefficient in each case being based on the sum of the flap and wing areas. No serious adverse change in lateral stability was found to result from the use of the flap in the optimum position.

WING FLAPS-WRAGG↗