Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sensor control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Extended Impedance Control Using Real and Virtual Sensors for Redundant Manipulators

Control of a redundant manipulator based on an impedence control framework with multiple simultaneous control sources is described. Each control source provides a different behavior type. An application is decomposed into multiple simultaneous behaviors whose resultant behavior will provide the motion necessary to execute the task. The simultaneous control inputs are merged using impedance control to compute a resultant command to the manipulator. The task space of each behavior can have the dimensionality of the mechanism being controlled. Control of a seven degree of freedom manipulator is described here with an available task space for each behavior of dimensionality seven.

telerobotics control architecture simultaneous beh↗

Buffet induced structural/flight-control system interaction of the X-29A aircraft

High angle-of-attack flight regime research is currently being conducted for modern fighter aircraft at the NASA Ames Research Center's Dryden Flight Research Facility. This flight regime provides enhanced maneuverability to fighter pilots in combat situations. Flight research data are being acquired to compare and validate advanced computational fluid dynamic solutions and wind-tunnel models. High angle-of-attack flight creates unique aerodynamic phenomena including wing rock and buffet on the airframe. These phenomena increase the level of excitation of the structural modes, especially on the vertical and horizontal stabilizers. With high gain digital flight-control systems, this structural response may result in an aeroservoelastic interaction. A structural interaction on the X-29A aircraft was observed during high angle-of-attack flight testing. The roll and yaw rate gyros sensed the aircraft's structural modes at 11, 13, and 16 Hz. The rate gyro output signals were then amplified through the flight-control laws and sent as commands to the flaperons and rudder. The flight data indicated that as the angle of attack increased, the amplitude of the buffet on the vertical stabilizer increased, which resulted in more excitation to the structural modes. The flight-control system sensors and command signals showed this increase in modal power at the structural frequencies up to a 30 degree angle-of-attack. Beyond a 30 degree angle-of-attack, the vertical stabilizer response, the feedback sensor amplitude, and control surface command signal amplitude remained relatively constant. Data are presented that show the increased modal power in the aircraft structural accelerometers, the feedback sensors, and the command signals as a function of angle of attack. This structural interaction is traced from the aerodynamic buffet to the flight-control surfaces.

Voracek, David F.↗

Sensors for Environmental Control

Under a Kennedy Space Center Small Business Innovation Research contract, GEO-CENTERS, Inc. developed a sensing element or 'optrode,' which NASA needed for space life support research to measure a hydroponic culture's pH factor. The company then commercialized the technology in the PC Based pH Monitoring System. The system employs the optrode to enable long term continuous monitoring of the pH level of fluids in standing and flowing conditions, an optoelectronic board with light sensors and detectors that fits into a desktop computer, and a fiber optic cable that connects the two. The system is effective in monitoring the pH output of industries to maintain ranges acceptable to the Environmental Protection Agency.

Source record↗

Multi-Wavelength Based Optical Density Sensor for Autonomous Monitoring of Microalgae

A multi-wavelength based optical density sensor unit was designed, developed, and evaluated to monitor microalgae growth in real time. The system consisted of five main components including (1) laser diode modules as light sources (2) photodiodes as detectors, (3) driver circuit, (4) flow cell and (5) sensor housing temperature controller. The sensor unit was designed to be integrated into any microalgae culture system for both real time and non-real time optical density measurements and algae growth monitoring applications. It was shown that the sensor unit was capable of monitoring the dynamics and physiological changes of the microalgae culture in real-time. Algae biomass concentration was accurately estimated with optical density measurements at 650, 685 and 780 nm wavelengths used by the sensor unit. The sensor unit was able to monitor cell concentration as high as 1.05 g L -1 (1.51x10 8 cells mL -1 ) during the culture growth without any sample preparation for the measurements. Since high cell concentrations do not need to be diluted using the sensor unit, the system has the potential to be used in industrial microalgae cultivation systems for real time monitoring and control applications that can lead to improved resource use efficiency.

09 BIOMASS FUELS↗

Application of x-ray tomography to optimization of new NOx/NH3 mixed potential sensors for vehicle on-board emissions control

Mixed potential sensors for the detection of hydrocarbons, NO{sub x}, and NH{sub 3} have been previously developed at Los Alamos National Laboratory (LANL). The LANL sensors have a unique design incorporating dense ceramic-pelletlmetal-wire electrodes and porous electrolytes. The performance of current-biased sensors using an yttria-stabilized zirconia (YSZ) electrolyte and platinum and La{sub 0.8}Sr{sub 0.2}CrO{sub 3} electrodes is reported. X-ray tomography has been applied to non-destructively examine internal structures of these sensors. NO{sub x} and hydrocarbon response of the sensors under various bias conditions is reported, and very little NO{sub x} response hysteresis was observed. The application of a 0.6 {mu}A bias to these sensors shifts the response from a hydrocarbon response to a NO{sub x} response equal for both NO and NO{sub 2} species at approximately 500 {sup o}C in air.

36 MATERIALS SCIENCE↗

Contact position sensor using constant contact force control system

A force control system (50) and method are provided for controlling a position contact sensor (10) so as to produce a constant controlled contact force therewith. The system (50) includes a contact position sensor (10) which has a contact probe (12) for contacting the surface of a target to be measured and an output signal (V.sub.o) for providing a position indication thereof. An actuator (30) is provided for controllably driving the contact position sensor (10) in response to an actuation control signal (I). A controller (52) receives the position indication signal (V.sub.o) and generates in response thereto the actuation control signal (I) so as to provide a substantially constant selective force (F) exerted by the contact probe (12). The actuation drive signal (I) is generated further in response to substantially linear approximation curves based on predetermined force and position data attained from the sensor (10) and the actuator (30).

Sturdevant, Jay↗

Design and Characterization of DNA Strand-Displacement Circuits in Serum-Supplemented Cell Medium

The functional stability and lifetimes of synthetic molecular circuits in biological environments are important for long-term, stable sensors or controllers of cell or tissue behavior. DNA-based molecular circuits, particularly DNA strand-displacement circuits, provide simple and effective biocompatible control mechanisms and sensors, but are vulnerable to digestion by nucleases present in living tissues and serum-supplemented cell culture. The stability of double-stranded and single-stranded DNA circuit components in serum-supplemented cell medium and the corresponding effect of nuclease-mediated degradation on circuit performance were characterized to determine the major routes of degradation and DNA strand-displacement circuit failure. Simple circuit design choices, such as the use of 5' toeholds within the DNA complexes used as reactants in the strand-displacement reactions and the termination of single-stranded components with DNA hairpin domains at the 3' termini, significantly increase the functional lifetime of the circuit components in the presence of nucleases. Furthermore, simulations of multireaction circuits, guided by the experimentally measured operation of single-reaction circuits, enable predictive realization of multilayer and competitive-reaction circuit behavior. Altogether, these results provide a basic route to increased DNA circuit stability in cell culture environments.

59 BASIC BIOLOGICAL SCIENCES↗

An Introduction to LANL Mixed Potential Sensors

These are slides for a webinar given on the topics of an introduction to LANL mixed potential sensors. Topics include the history of LANL electrochemical sensor work, an introduction to mixed potential sensors, LANL uniqueness, and an application of LANL mixed potential sensors. The summary is as follows: Improved understanding of the mixed-potential sensor mechanism (factors controlling the sensor response identified), sensor design optimized to maximize sensor sensitivity and durability (porous electrolyte/dense electrodes), electrodes selected for various specific applications (CO, HC, H 2 ), sensor operating parameters optimized for improved gas selectivity (NO x , NH 3 ).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Issues in advanced automation for manipulator control

This paper provides a brief description and analysis of the main issues in advanced autonomous control of manipulators as seen from a system point of view. The nature of manipulation is analyzed at some depth. A general multilevel structure is outlined for manipulator control organization which includes the human operator at the top level of the control structure. Different approaches to the development of advanced automation of mechanical arms are summarized. Recent work in the JPL teleoperator project is described, including control system, force/torque sensor, and control software development. Some results from control experiments are summarized.

Bejczy, A. K.↗

In-situ measurements of alloy oxidation/corrosion/erosion using a video camera and proximity sensor with microcomputer control

Two noncontacting and nondestructive, remotely controlled methods of measuring the progress of oxidation/corrosion/erosion of metal alloys, exposed to flame test conditions, are described. The external diameter of a sample under test in a flame was measured by a video camera width measurement system. An eddy current proximity probe system, for measurements outside of the flame, was also developed and tested. The two techniques were applied to the measurement of the oxidation of 304 stainless steel at 910 C using a Mach 0.3 flame. The eddy current probe system yielded a recession rate of 0.41 mils diameter loss per hour and the video system gave 0.27.

Deadmore, D. L.↗

Optimal quasi-static shape control for large aerospace antennae

In this paper, an on-line control approach which will adjust the steady-state shape of a large antenna arbitarily close to any achievable desired profile is proposed. The method makes use of distributed parameter system theory and allows refocusing using a limited number of control actuators and sensors. The controller gains are calculated by approximating the solution to an infinite-dimensional optimal quasi-static control problem. A very general convergence result for such quasi-static controllers is proved and applied to the antenna controller to show convergence, using any Galerkin (finite-element) approximation method.

Balas, M. J.↗

Suboptimal shape control for quasi-static distributed-parameter systems

An on-line control approach which will adjust the steady-state shape of a large antenna arbitrarily close to any achievable desired profile is approached. The method makes use of distributed-parameter system theory and allows refocusing using a limited number of control actuators and sensors. The controller gains are calculated by approximating the solution to an infinite-dimensional optimal quasi-static control problem. The controller gain calculation is computationally simpler than that previously proposed. The Galerkin (finite element) approximation method is used for model reduction. It is proved that both gain and state convergence can be achieved by using the proposed approximation scheme.

Balas, M. J.↗

RCTS: A flexible environment for sensor integration and control of robot systems; the distributed processing approach

Most robot systems lack a suitable hardware and software environment for the efficient research of new control and sensing schemes. Typically, engineers and researchers need to be experts in control, sensing, programming, communication and robotics in order to implement, integrate and test new ideas in a robot system. In order to reduce this time, the Robot Controller Test Station (RCTS) has been developed. It uses a modular hardware and software architecture allowing easy physical and functional reconfiguration of a robot. This is accomplished by emphasizing four major design goals: flexibility, portability, ease of use, and ease of modification. An enhanced distributed processing version of RCTS is described. It features an expanded and more flexible communication system design. Distributed processing results in the availability of more local computing power and retains the low cost of microprocessors. A large number of possible communication, control and sensing schemes can therefore be easily introduced and tested, using the same basic software structure.

Allard, R.↗