Search NASA⌕ Search

SEARCH · Search NASA

Results for “Skin Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Turbulent boundary layer over porous surfaces with different surface geometries

The turbulent boundary layer over three porous walls with different surface geometries was studied in order to investigate the individual influences of porosity and small roughness, as well as their combined effects, on turbulent boundary layer behavior. The tests were conducted in a 2 m x 2 m tunnel on a large axisymmetric model at speeds corresponding to Re(L) = 5,000,000-6,000,000. The development of the turbulent boundary layer was compared for that of sintered metal, bonded screening, and perforated sheet and then to that for the flow over a solid smooth wall and a solid, sand-roughened wall. The comparisons reveal that the effect of porosity is to shift the logarithmic region of the wall law down by a certain amount from the solid wall results and to increase the skin friction values by about 30-40%. The downward shift of the logarithmic region of the wall law and the increase of the skin friction value by the combined effects of small roughness and porosity are found to be roughly the sum of their individual effects.

Kong, F. Y.↗
NASA NTRS1986

Airfoil large eddy breakup devices for turbulent drag reduction

It was determined from the present LaRC experiments that tandem, airfoil-shaped large eddy breakup (LEBU) devices can reduce local skin friction as much as 30 percent with a recovery region extending more than 100 boundary layer thicknesses downstream. These airfoils experience near laminar skin friction device drag and produce net drag reductions of up to 7 percent. In contrast to the thin plates used in previous experiments, these airfoils are more than 1000 time stiffer and hence have the potential to withstand the real flight environment (dynamic pressure 36 times larger than in low-speed wing tunnels). In addition, the higher Reynolds numbers of the present tests indicate drag reduction performance is at least as good (or better) as at lower Reynolds numbers.

Anders, J. B.↗
NASA NTRSDate not supplied

Design Exploration of a Transonic Cruise Slotted Airfoil

A knowledge-based aerodynamic design method, CDISC, has been leveraged for the computational design exploration of the cruise slotted airfoil as a drag-saving technology for single aisle, transonic transport aircraft. Aerodynamic predictions were generated using the NASA USM3D Reynolds-averaged Navier-Stokes flow solver, and laminar flow assessments were conducted using the NASA BLSTA3D boundary layer profile solver paired with the LASTRAC stability analysis and transition prediction software. The CDISC design method was used to parametrically vary several slotted-airfoil design variables to understand their impact on aerodynamic performance. In addition to establishing best practices for slotted airfoil design, it was observed that the historically noted skin-friction penalty for cruise slotted airfoils was attributed to the low-Reynolds-number boundary layer of the flap. At cruise, this skin-friction penalty negated any potential decrease in pressure drag enabled by the cruise slotted airfoil architecture. This observation led to the development of an Aft-Laminar Multi-element Airfoil concept that uses airfoil shaping to promote natural laminar flow on the flap. At cruise conditions, the concept is predicted to offer a 2.7% reduction in sectional drag relative to a fully turbulent supercritical airfoil. Off-design analyses showed that laminar flow could be maintained with near-cruise variations in angle of attack and Mach number, resulting in sustained aerodynamic efficiency improvements and a delay in the drag rise Mach number. A low-speed, high-lift analysis at takeoff conditions predicted a maximum lift coefficient of 2.4 could be achieved by use of a variable-camber leading edge on the main element and simple deflection of the flap. These computationally-predicted benefits have motivated future research toward an aft-laminar cruise slotted wing design as an incremental step toward the application of natural laminar flow technology on transonic commercial transports.

Brett R Hiller↗
NASA NTRS1990

Swept shock/boundary layer interaction experiments in support of CFD code validation

Research on the topic of shock wave/turbulent boundary layer interaction was carried out. Skin friction and surface pressure measurements in fin-induced, swept interactions were conducted, and heat transfer measurements in the same flows are planned. The skin friction data for a strong interaction case (Mach 4, fin-angles equal 16 and 20 degrees) were obtained, and their comparison with computational results was published. Surface pressure data for weak-to-strong fin interactions were also obtained.

Settles, G. S.↗
NASA NTRS2000

Design and Evaluation of a New Boundary-Layer Rake for Flight Testing

A new boundary-layer rake has been designed and built for flight testing on the NASA Dryden Flight Research Center F-15B/Flight Test Fixture. A feature unique to this rake is its curved body, which allows pitot tubes to be more densely clustered in the near-wall region than conventional rakes allow. This curved rake design has a complex three-dimensional shape that requires innovative solid-modeling and machining techniques. Finite-element stress analysis of the new design shows high factors of safety. The rake has passed a ground test in which random vibration measuring 12 g rms was applied for 20 min in each of the three normal directions. Aerodynamic evaluation of the rake has been conducted in the NASA Glenn Research Center 8 x 6 Supersonic Wind Tunnel at Mach 0-2. The pitot pressures from the new rake agree with conventional rake data over the range of Mach numbers tested. The boundary-layer profiles computed from the rake data have been shown to have the standard logarithmic-law profile. Skin friction values computed from the rake data using the Clauser plot method agree with the Preston tube results and the van Driest II compressible skin friction correlation to approximately +/-5 percent.

Bui, Trong T.↗
NASA NTRSDate not supplied

Wall-modeled LES of the NASA Juncture Flow Experiment

We perform wall-modeled large eddy simulation (WMLES) of the NASA Juncture Flow experiment (Kegerise & Neuhart, NASA/TM–2019–20286) using an equilibrium wall model and unstructured finite volume solver, to assess its predictive ability for complex geometries. The flow condition simulated corresponds to 5 degrees angle of attack with a freestream Mach number of 0.189, and a Reynolds number based on the mean crank chord of 2.4 million. All simulations neglect the effects of wind tunnel walls, sting and mast present in the experiment. To assess the performance of WMLES on simpler flows with very coarse grids, we simulate flow in a turbulent channel at a friction Reynolds number, Reτ≈2000, and flow through a square duct at anReτ≈1000. The duct flow results using the equilibrium wall model indicate that the skin friction is inaccurate near the corner for grid topologies and resolutions typically used in WMLES, having implications for more complicated flows such as the juncture flow. For the juncture flow simulation, two different approaches are investigated. The first approach consists of a truncated-domain simulation wherein the inflow plane of the computational domain is placed at≈0.2chord length of the wing, and we prescribe the mean flow from a separate Reynolds-averaged Navier-Stokes (RANS) solution along with synthetic turbulence to initiate realistic unsteadiness in the domain. The second approach involves simulating the entire geometry with trips to trigger transition to turbulence. The truncated- and full-domain simulations contain about 62 and 90 million cells, respectively; with 8-10 points per boundary layer thickness in the wall-parallel directions, 14-20 points in the wall-normal direction and a near-wall viscous spacing (∆n+1) of≈100. Preliminary results are encouraging overall in terms of the prediction of wall pressure, wall skin friction, velocity and stresses; but indicate that further work is required to improve the predictions in the separation bubble and wing-fuselage corner regions. The grid resolution used in this study is still fairly coarse, and the results should be interpreted as work in progress.

Prahladh S Iyer↗
NASA NTRS1990

Boundary layer manipulators at high Reynolds numbers

Airfoil large-eddy breakup (LEBU) devices were tested on an axisymmetric body in the Langley Two Tank up to speeds of 50 ft/sec. NACA-0009, NACA-2412, E-193, and Clark Y contours were tested in single and tandem configurations. At the higher Reynolds numbers local skin friction downstream of the devices showed minimal reductions O (10 percent) and total body drag was increased 1 to 3 percent. At lower Reynolds numbers skin-friction reductions as large as 25 percent were measured and total body drag tended toward net reductions. The loss of effectiveness with increasing Reynolds number of conventional, outer layer devices suggests a decoupling of the outer and inner scales in high Reynolds number turbulent boundary layers.

Anders, J. B.↗
NASA NTRS2015

Direct Simulation of Flow over A Wall-Mounted Hump

Simulating separated flows at high Reynolds numbers using Reynolds Averaged Navier-Stokes (RANS) modeled equations remains a challenge in aeronautics. The main hindrance to progress stems from the lack of extended de- tailed data pertinent to the root cause of failure of RANS models, as well as the little progress in RANS modeling innovations in the past several decades. The goal of the current effort is to generate data for separated flow at a Reynolds numbers where conventional models are challenged. We use Direct Numerical Simulations to model turbulent flow over the wall-mounted hump configuration to investigate the physics of flow separation and boundary layer recovery, as well as provide data relevant to the modeling community. A chord-based Reynolds number of Re(sub c) = 47,500 is considered with a turbulent inflow profile of Re(sub θ) = 1,400 (θ /c = 3%). We use FDL3DI, a code that solves the compressible Navier-Stokes equations using high-order compact-difference scheme and filter, with the standard re- cycling/rescaling method of generating turbulent boundary layers as inflow to the computational domain. Two differ- ent configurations of the upper-wall are analyzed for two sets of boundary conditions (slip and no-slip). The results are compared with the available higher Re(sub c) (= 936,000, Re(sub θ) = 7,200, θ /c = 0.77%) experiment for major flow features. The simulated lower Rec allows for DNS-like mesh resolutions, and adequately wide spans. The results from these simulations show earlier separation and delayed reattachment compared to Re(sub c) = 936,000, and significantly higher skin friction in the forebody of the hump. We also find that the upper-wall shape and boundary condition influence pressure distribution over the hump, whereas skin friction is only influenced by the boundary condition.

Wall-Mounted↗
NASA NTRS1993

Analysis and evaluation of an integrated laminar flow control propulsion system

Reduction of drag has been a major goal of the aircraft industry as no other single quantity influences the operating costs of transport aircraft more than aerodynamic drag. It has been estimated that even modest reduction of frictional drag could reduce fuel costs by anywhere from 2 to 5 percent. Current research on boundary layer drag reduction deals with various approaches to reduce turbulent skin friction drag as a means of improving aircraft performance. One of the techniques belonging to this category is laminar flow control in which extensive regions of laminar flow are maintained over aircraft surfaces by delaying transition to turbulence through the ingestion of boundary layer air. While problems of laminar flow control have been studied in some detail, the prospect of improving the propulsion system of an aircraft by the use of ingested boundary layer air has received very little attention. An initial study for the purpose of reducing propulsion system requirements by utilizing the kinetic energy of boundary layer air was performed in the mid-1970's at LeRC. This study which was based on ingesting the boundary layer air at a single location, did not yield any significant overall propulsion benefits; therefore, the concept was not pursued further. However, since then it has been proposed that if the boundary layer air were ingested at various locations on the aircraft surface instead of just at one site, an improvement in the propulsion system might be realized. The present report provides a review of laminar flow control by suction and focuses on the problems of reducing skin friction drag by maintaining extensive regions of laminar flow over the aircraft surfaces. In addition, it includes an evaluation of an aircraft propulsion system that is augmented by ingested boundary layer air.

Keith, Theo G., Jr.↗
NASA NTRS1993

Supersonic boundary-layer flow turbulence modeling

Baldwin-Lomax and kappa-epsilon turbulence models were modified for use in Navier-Stokes numerical computations of Mach 2.9 supersonic turbulent boundary layer flows along compression ramps. The computational results of Reynolds shear stress profiles were compared with experimental data. The Baldwin-Lomax model was modified to account for the Reynolds shear stress amplification within the flow field. A hybrid kappa-epsilon model with viscous sublayer turbulence treatment was constructed to predict the Reynolds shear stress profiles within the entire flow field. These modified turbulence models were effective for the computations of the surface pressure and the skin friction factor variations along an 8 deg ramp surface. The hybrid kappa-epsilon model could improve the predictions of the Reynolds shear stress profile and the skin friction factor near the corner of a 16 deg ramp.

Wang, Chi-Rong↗
NASA NTRSDate not supplied

Simulation and Modeling of Hypersonic Turbulent Boundary Layers Subject to Favorable Pressure Gradients due to Streamline Curvature

Direct numerical simulations (DNS) of favorable-pressure-gradient turbulent boundary layers are presented for a nominal freestream Mach number of 5, with the objective of assessing the limitations of the currently available Reynolds-averaged Navier-Stokes (RANS) models. The favorable pressure gradient is induced by the streamwise curvature of the two-dimensional, planar, convex measurement surface used during experiments at the Texas A&M University. The DNS data shows good comparison with the measured velocity profiles, strain rates, and some, but not all, of the Reynolds-stress components. The discrepancies between the predicted and the measured wall-normal as well as shear stress components are primarily attributed to the lower than actual values inferred from typical PIV measurements of turbulent boundary layers. The DNS data shows a zero or slightly negative Reynolds shear stress in the outer part of the boundary-layer, which is indicative of the decaying turbulent motion under a strong favorable pressure gradient. The DNS data is also compared with the results of RANS computations based on commonly used zero, one, and two equation eddy-viscosity models. The RANS models yield reasonable comparisons with the DNS-based skin friction under zero and weak pressure gradients, but significant discrepancies under a strong pressure gradient. The k-w SST model provided the best overall predictions of skin friction, except in the region where the flow transitions from a favorable to an adverse pressure gradient. While the RANS models examined herein also give good predictions of the Reynolds shear stress under a sufficiently weak pressure gradient, none of those models are able to appropriately capture the reduction in the Reynolds stresses when the flow was subjected to a strong pressure gradient. An a priori assessment of the turbulent heat-flux prediction based on the assumption of a constant turbulent Prandtl number with the DNS data shows that while the constant turbulent Prandtl number model is effective in predicting the wall-normal component of turbulent heat flux, it does not capture the turbulent heat transfer in the streamwise direction for all the pressure gradient cases. The failure of the constant turbulent Prandtl number model highlights a requirement for more advanced models of the turbulent heat flux.

turbulent boundary layers↗
NASA NTRS1977

Downstream influence of swept slot injection in hypersonic turbulent flow

Results of an experimental and numerical investigation of tangential swept slot injection into a thick turbulent boundary layer at Mach 6 are presented. Film cooling effectiveness, skin friction, and flow structure downstream of the swept slot injection were investigated. The data were compared with that for unswept slots, and it was found that cooling effectiveness and skin friction reductions are not significantly affected by sweeping the slot.

Hefner, J. N.↗
NASA NTRS2005

Navier-Stokes Computations With One-Equation Turbulence Model for Flows Along Concave Wall Surfaces

This report presents the use of a time-marching three-dimensional compressible Navier-Stokes equation numerical solver with a one-equation turbulence model to simulate the flow fields developed along concave wall surfaces without and with a downstream extension flat wall surface. The 3-D Navier- Stokes numerical solver came from the NASA Glenn-HT code. The one-equation turbulence model was derived from the Spalart and Allmaras model. The computational approach was first calibrated with the computations of the velocity and Reynolds shear stress profiles of a steady flat plate boundary layer flow. The computational approach was then used to simulate developing boundary layer flows along concave wall surfaces without and with a downstream extension wall. The author investigated the computational results of surface friction factors, near surface velocity components, near wall temperatures, and a turbulent shear stress component in terms of turbulence modeling, computational mesh configurations, inlet turbulence level, and time iteration step. The computational results were compared with existing measurements of skin friction factors, velocity components, and shear stresses of the developing boundary layer flows. With a fine computational mesh and a one-equation model, the computational approach could predict accurately the skin friction factors, near surface velocity and temperature, and shear stress within the flows. The computed velocity components and shear stresses also showed the vortices effect on the velocity variations over a concave wall. The computed eddy viscosities at the near wall locations were also compared with the results from a two equation turbulence modeling technique. The inlet turbulence length scale was found to have little effect on the eddy viscosities at locations near the concave wall surface. The eddy viscosities, from the one-equation and two-equation modeling, were comparable at most stream-wise stations. The present one-equation turbulence model is an effective approach for turbulence modeling in the near solid wall surface region of flow over a concave wall.

Wang, Chi R.↗
NASA NTRS1979

Diagnosis of separated flow regions on wind-tunnel models using an infrared camera

A novel technique utilizing an infrared-sensitive imaging camera has been used to determine the location of three-dimensional (3-D) separated flow regions on an inclined 5 deg semiangle fiberglass cone. The results illustrate that there is a change in the contrast of the infrared (IR) signature on the cone surface corresponding with the location where the skin-friction lines merge toward lines of 3-D separation. This technique should offer a convenient means for locating separated flow regions on wind-tunnel models while obtaining simultaneous force, skin-friction, and pressure data.

Bandettini, A.↗
NASA NTRS1984

Experimental study of flow reattachment in a single-sided sudden expansion

The reattachment of a fully turbulent, two dimensional, separated shear layer downstream of a single-sided sudden expansion in a planar duct flow was examined experimentally. The importance of changing the structure of the separated shear layer on the reattachment process itself was examined. For all cases, the Reynolds number based on step height was greater than 20,000, the expansion ratio was 5/3, and the inlet boundary layer was less than one-half step height in thickness. A crucially important phase was the development of a pulsed wall probe for measurement of skin friction in the reattachment region, thus providing an unambiguous definition of the reattachment length. Quantitative features of reattachment - including streamwise development of the mean and fluctuating velocity field, pressure rise, and skin friction - were found to be similar for all cases studied when scaled by the reattachment length. A definition of the reattachment zone is proposed.

Westphal, R. V.↗
NASA NTRS1991

Implementation of wall boundary conditions for transpiration in F3D thin-layer Navier-Stokes code

Numerical boundary conditions for mass injection/suction at the wall are incorporated in the thin-layer Navier-Stokes code, F3D. The accuracy of the boundary conditions and the code is assessed by a detailed comparison of the predictions of velocity distributions and skin-friction coefficients with exact similarity solutions for laminar flow over a flat plate with variable blowing/suction, and measurements for turbulent flow past a flat plate with uniform blowing. In laminar flow, F3D predictions for friction coefficient compare well with exact similarity solution with and without suction, but produces large errors at moderate-to-large values of blowing. A slight Mach number dependence of skin-friction coefficient due to blowing in turbulent flow is computed by F3D code. Predicted surface pressures for turbulent flow past an airfoil with mass injection are in qualitative agreement with measurements for a flat plate.

Kandula, M.↗
NASA NTRS1943

Determination of general relations for the behavior of turbulent boundary layers

An analysis has been made of a considerable amount of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. It was found that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter. This parameter was chosen as the ratio of the displacement thickness to the momentum thickness of the boundary layer. The variables that control the development of the turbulent boundary layer apparently are: (1) the ratio of the nondimensional pressure gradient, expressed in terms of the local dynamic pressure outside the boundary layer and boundary-layer thickness, to the local skin-friction coefficient and (2) the shape of the boundary layer. An empirical equation has been developed in terms of these variables that, when used with the momentum equation and the skin-friction relation, makes it possible to trace the development of the turbulent boundary layer to the separation point.

Von Doenhoff, Albert E↗
NASA NTRS1990

Turbulence modeling for sharp-fin-induced shock wave/turbulent boundary-layer interactions

Solutions of the Reynolds averaged Navier-Stokes equations are presented and compared with a family of experimental results for the 3-D interaction of a sharp fin induced shock wave with a turbulent boundary layer. Several algebraic and two equation eddy viscosity turbulence models are employed. The computed results are compared with experimental surface pressure, skin friction, and yaw angle data as well as the overall size of the interaction. Although the major feature of the flow fields are correctly predicted, several discrepancies are noted. Namely, the maximum skin friction values are significantly underpredicted for the strongest interaction cases. These and other deficiencies are discussed.

Horstman, C. C.↗