Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sonic Boom”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

The development of a sonic boom simulator with detonable gases

A sonic boom pressure profile was simulated in the far-field by detonation of a methane-oxygen mixture contained in a slender, shaped Mylar envelope. Ideal N-waves were synthesized with peak overpressures from two to five psf and durations of 30 to 75 milliseconds. The detonation of the gas mixture was initiated by a single Primacord strand running the length of balloon. The N-wave producing balloon was synthesized as a composite structure, utilizing experimental pressure profiles obtained from the detonations of slender, axisymmetric balloons with elementary, non-cylindrical shapes.

Strugielski, R. T.↗
NASA NTRS1974

Aircraft design for flight below the sonic boom speed limit

The avoidance of sonic booms places a constraint on aircraft design and can lead to unusual new configurations. From a comparison among several candidate designs, it is shown that an oblique-wing aircraft offers many advantages when structure, stability, flight efficiency, and airport noise are considered jointly.

Jones, R. T.↗
NASA NTRS1975

Instrumentation for measurement of aircraft noise and sonic boom

A jet aircraft noise and sonic boom measuring device which converts sound pressure into electric current is described. An electric current proportional to the sound pressure level at a condenser microphone is produced and transmitted over a cable, amplified by a zero drive amplifier and recorded on magnetic tape. The converter is comprised of a local oscillator, a dual-gate field-effect transistor (FET) mixer and a voltage regulator/impedance translator. A carrier voltage that is applied to one of the gates of the FET mixer is generated by the local oscillator. The microphone signal is mixed with the carrier to produce an electrical current at the frequency of vibration of the microphone diaphragm by the FET mixer. The voltage of the local oscillator and mixer stages is regulated, the carrier at the output is eliminated, and a low output impedance at the cable terminals is provided by the voltage regulator/impedance translator.

Zuckerwar, A. J.↗
NASA NTRS1976

Aircraft design for flight below the sonic boom speed limit

The avoidance of sonic booms places a constraint on aircraft design and can lead to unusual new configurations. From a comparison among several candidate designs, it is shown that an oblique winged aircraft offers many advantages when structure, stability, flight efficiency, and airport noise are considered jointly.

Jones, R. T.↗
NASA NTRS2003

A Quick Method for Evaluating the Merits of a Proposed Low Sonic Boom Concept

The characteristics of a proposed low-boom aircraft concept cannot be adequately assessed unless it is given an extensive, time-consuming, mission-performance, and sonic-boom analyses. So, it would be useful to have a method for performing a quick first-order sonic-boom and mission-range analysis. The evaluation method outlined in this report has the attributes of being both fast and reasonably accurate. It can also be used as a design tool to estimate the sonic-boom ground overpressures, mission range, and beginning-cruise weight of a new low-boom concept during the first stages of preliminary design.

Mack, Robert J.↗
NASA NTRS1992

A numerical model for sonic boom propagation through an inhomogeneous, windy atmosphere

The ZEPHYRUS computer model calculates sonic boom distortion during propagation through the atmosphere. The model includes the effects of nonlinear distortion, attenuation, dispersion, and wind. Trial runs with the model indicate that, in general, stable shocks have not formed when the sonic boom reaches the ground. Also, the rise time of the lead shock may strongly depend on the overall waveform shape, and may be significantly increased by purely dispersive effects when matching occurs between the rise time and the characteristic oxygen molecular relaxation time.

Robinson, Leick D.↗
NASA NTRS1996

The Use of Structural-Acoustic Techniques to Assess Potential Structural Damage From Sonic Booms

The potential impact of supersonic operations includes structural damage from the sonic boom overpressure. This paper describes a study of how structural-acoustic modeling and testing techniques may be used to assess the potential for such damage in the absence of actual flyovers. Procedures are described whereby transfer functions relating structural response to sonic boom signature may be obtained with a stationary acoustic source and appropriate data processing. Further, by invoking structural-acoustic reciprocity, these transfer functions may also be acquired by measuring the radiated sound from the structure under a mechanical drive. The approach is based on the fundamental assumption of linearity, both with regard to the (acoustic) propagation of the boom in the vicinity of the structure and to the structure's response. Practical issues revolve around acoustic far field and source directivity requirements. The technique was implemented on a specially fabricated test structure at Edwards AFB, CA with the support of Wyle Laboratories, Inc. Blank shots from a cannon served as our acoustic source and taps from an instrumented hammer generated the mechanical drive. Simulated response functions were constructed. Results of comparisons with corresponding measurements recorded during dedicated supersonic flyovers with F-15 aircraft are presented for a number of sensor placements.

Garrelick, Joel↗
NASA NTRSDate not supplied

USM3D Simulations for the Third Sonic Boom Prediction Workshop (SBPW-3)

The NASA USM3D flow solver was used to compute test cases for the Third AIAA Sonic Boom Prediction Workshop (SBPW3). The test cases include a nearfield biconvex shock-plume interaction wind tunnel model, and the C608 Low Boom Flight Demonstrator. Numerical simulations were conducted on the mixed-element and tetrahedral grids provided by the workshop committee, as well as a family of grids generated by an in-house approach for sonic boom analyses known as BoomGrid. The near-field pressure signatures were extracted, propagated to the ground and the perceived loudness levels on the ground were computed. The USM3D near-field pressure signatures, corresponding ground signatures, and loudness levels on the ground are compared with that of mean values from other workshop participants. The effect of three flux-limiters on the accuracy of near-field pressure signatures prediction was investigated and results are compared with that of mean values from other workshop participants. The effect of using wall function grids in accurately predicting near-field pressure signatures was also evaluated.

Supersonics↗
NASA NTRS1993

Investigation of sonic boom for the Space Shuttle: High cross-range orbiter

Recent studies of a proposed low cross-range straight-wing space shuttle orbiter have shown that the sonic boom created during reentry may be objectionable, particularly at low supersonic Mach number. Because of this, additional tests have been conducted to determine the sonic-boom overpressure for a blended wing-body shape proposed for use as a high cross-range shuttle orbiter. Two mission profiles, in which a constant angle of attack was held during the supersonic portion of the flight, were studied. In one case the angle of attack was 60 degrees; in the other 25 degrees. The sonic-boom pressure signatures were measured in a wind tunnel and used to estimate overpressures for both missions. A technique for alleviating the boom is indicated.

Hicks, Raymond M.↗
NASA NTRS1972

Development and evaluation of a device to simulate a sonic boom

A device to simulate the vibrational and acoustical properties of a sonic boom was developed and evaluated. The design employed a moving circular diaphragm which produced pressure variations by altering the volume of an air-tight enclosure that was located adjacent to an acoustical test chamber. A review of construction oriented problems, along with their solutions, is presented. The simulator is shown to produce the effects of sonic booms having pressure signatures with rise times as low as 5 milliseconds, durations as short as 80 milliseconds, and overpressures as high as 2.5 pounds per square foot. Variations in the signatures are possible by independent adjustments of the simulator. The energy spectral density is also shown to be in agreement with theory and with actual measurements for aircraft.

Rash, L. C.↗