Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effect of trailing edge geometry and thickness on the performance of certain turbine stator blading

The experimental and analytical investigation included solid blades with five different trailing-edge thicknesses and four different trailing-edge geometries. One of the geometries was round, one was square, one was tapered from the suction surface, and the other tapered from the pressure surface. One of the trailing-edge thicknesses was sharp edged; the other four thicknesses were equivalent to about 5, 11, 16, and 20 percent of the blade throat width. The experimental results show increased efficiency loss for increased trailing-edge thickness for all trailing-edge geometries. The blade with round trailing edge, equal to about 11 percent of the blade throat width, had 60 percent more loss than the sharp-edged blade. For the same trailing-edge thickness, square trailing edges caused more loss than round trailing edges, and the tapered trailing edges caused about the same loss as the round trailing edges.

Prust, H. W., Jr.↗
NASA NTRS1972

Nonuniform flow field generation for supersonic compressor stator development: Design and preliminary results

Design and preliminary results are given for a technique which can generate a nonuniform flow similar to the discharge of an impulse supersonic compressor rotor. The technique utilizes a carefully contoured, two-dimensional blunt body in a conventional hypersonic wind tunnel to generate the required flow field. To show the effects of the flow vorticity, a cascade of impulse-type blades was tested in this test stream. Some preliminary performance data are given along with comparison with previously determined uniform flow results.

Lipfert, F. W.↗
NASA NTRS1972

Flow conditions around the exit and downstream of certain stator blading with various trailing edge thicknesses and geometries

The blading investigated was curved back with thick profiles. The variations in flow conditions considered were flow angle and isentropic energy. Experimental data were obtained in a two-dimensional cascade from surveys with a combined angle, total-, and static-pressure probe and from an array of end-wall static pressure taps. Analytical results were obtained from ideal flow theory. The results showed large variations in flow conditions close to the plane of the trailing edge that were largely attenuated at a distance a little greater than one blade pitch downstream of the trailing edge in the direction of flow. The results were affected by the geometry and thickness of the trailing edge. The agreement between experimental and analytical results is generally fair to excellent.

Prust, H. W., Jr.↗
NASA NTRS1973

Cold-air aerodynamic study in a two-dimensional cascade of a turbine stator blade with suction-surface film cooling

The effect on aerodynamic performance of a single row of spanwise-spaced coolant holes located at four positions chordwise along the suction surface was investigated. In addition, multiple-row data were obtained. The data are presented in terms of primary efficiency, coolant-to-primary-flow percentage, and coolant pressure ratio. Primary efficiencies of multirow blade configurations compare satisfactorily with that calculated from the single-row efficiency increments. At any given coolant flow percentage, the efficiency was about the same for all row locations. For a given coolant pressure, the efficiency varied by as much as 1 percent, depending on the row location.

Brown, D. B.↗
NASA NTRS1973

Single-stage experimental evaluation of tandem-airfoil rotor stator blading for compressors. Part 6: Data and performance for stage D

An axial flow compressor stage, having single-airfoil blading, was designed for zero rotor prewhirl, constant rotor work across the span, and axial discharge flow. The stage was designed to produce a pressure ratio of 1.265 at a rotor tip velocity of 757 ft/sec. The rotor had an inlet hub/tip ratio of 0.8. The design procedure accounted for the rotor inlet boundary layer and included the effects of axial velocity ratio and secondary flow on blade row performance. The objectives of this experimental program were: (1) to obtain performance with uniform and distorted inlet flow for comparison with the performance of a stage consisting of tandem-airfoil blading designed for the same vector diagrams; and (2) to evaluate the effectiveness of accounting for the inlet boundary layer, axial velocity ratio, and secondary flows in the stage design. With uniform inlet flow, the rotor achieved a maximum adiabatic efficiency of 90.1% at design equivalent rotor speed and a pressure ratio of 1.281. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 86.1% at a pressure ratio of 1.266. Hub radial, tip radial, and circumferential distortion of the inlet flow caused reductions in surge pressure ratio of approximately 2, 10 and 5%, respectively, at design rotor speed.

Clemmons, D. R.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 7: Data and performance for stage E

An axial flow compressor stage, having tandem airfoil blading, was designed for zero rotor prewhirl, constant rotor work across the span, and axial discharge flow. The stage was designed to produce a pressure ratio of 1.265 at a rotor tip velocity of 757 ft/sec. The rotor has an inlet hub/tip ratio of 0.8. The design procedure accounted for the rotor inlet boundary layer and included the effects of axial velocity ratio and secondary flow on blade row performance. The objectives of this experimental program were (1) to obtain performance with uniform and distorted inlet flow for comparison with the performance of a stage consisting of single-airfoil blading designed for the same vector diagrams and (2) to evaluate the effectiveness of accounting for the inlet boundary layer, axial velocity ratio, and secondary flows in the stage design.

Cheatham, J. G.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors, part 8

An experimental investigation was conducted with an 0.8 hub/tip ratio, single-stage, axial flow compressor to determine the potential of tandem-airfoil blading for improving the efficiency and stable operating range of compressor stages. The investigation included testing of a baseline stage with single-airfoil blading and two tandem-blade stages. The overall performance of the baseline stage and the tandem-blade stage with a 20-80% loading split was considerably below the design prediction. The other tandem-blade stage, which had a rotor with a 50-50% loading split, came within 4.5% of the design pressure rise (delta P(bar)/P(bar) sub 1) and matched the design stage efficiency. The baseline stage with single-airfoil blading, which was designed to account for the actual rotor inlet velocity profile and the effects of axial velocity ratio and secondary flow, achieved the design predicted performance. The corresponding tandem-blade stage (50-50% loading split in both blade rows) slightly exceeded the design pressure rise but was 1.5 percentage points low in efficiency. The tandem rotors tested during both phases demonstrated higher pressure rise and efficiency than the corresponding single-airfoil rotor, with identical inlet and exit airfoil angles.

Brent, J. A.↗
NASA NTRS1978

Two-dimensional cold-air cascade study of a film-cooled turbine stator blade. 5: Comparison of experimental and analytical aerodynamic results for blade with 12 rows of 0.038-centimeter-(0.015 inch) diameter coolant holes having streamwise ejection angles

Published experimental aerodynamic efficiency results were compared with results predicted from two published analytical methods. This is the second of two such comparisons. One of the analytical methods was used as published; the other was modified for certain cases of coolant discharge from the blade suction surface. The results show that for 23 cases of single row and multirow discharge covering coolant fractions from 0 to about 9 percent, the difference between the experimental and predicted results was no greater than about 1 percent in any case and less than 1/2 percent in most cases.

Prust, H. W., Jr.↗
NASA NTRS1978

Performance of single-stage axial-flow transonic compressor with rotor and stator aspect ratios of 1.19 and 1.26, respectively, and with design pressure ratio of 1.82

The overall and blade-element performance of a low-aspect-ratio transonic compressor stage is presented over the stable operating flow range at 70, 90, and 100 percent design speeds. At design speed the rotor and stage achieved peak efficiencies of 0.872 and 0.845 at pressure ratios of 1.875 and 1.842, respectively. The stage stall margin at design speed was 21.8 percent.

Reid, L.↗