Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Flutter Analysis of the Transonic Truss-Braced Wing Aircraft Using Transonic Correction

This paper describes a flutter analysis method for the Transonic Truss-Braced Wing aircraft using a vortex lattice method coupled to an unsteady transonic correction method to account for unsteady aerodynamics in transonic flow. A steady-state vortex-lattice model of the Truss-Braced Wing aircraft is developed using vortex lattice code VSPAERO. A transonic and viscous flow correction method is implemented in the VSPAERO model to account for steady-state transonic and viscous flow effects using transonic small disturbance code TSFOIL coupled to an in-house integral boundary layer code. In addition, a wing-strut interference correction method is developed to account for the transonic interference aerodynamics in the strut juncture region using high-fidelity CFD code FUN3D. A structural dynamic finite-element model of the Truss-Braced Wing aircraft is developed using BEAM3D in-house finite-element code and is coupled to the VSPAERO. The BEAM3D model includes a geometric nonlinearity due to the tension in the strut which causes a deflection-dependent nonlinear stiffness. An unsteady transonic correction method is developed to better capture the unsteady aerodynamics in transonic flow. The unsteady transonic correction method makes use of the Theodorsen’s theory to account for the amplitude and phase shift of the unsteady lift coefficient in transonic flow. A preliminary flutter analysis of the Truss-Braced Wing aircraft is conduct to illustrate the unsteady transonic correction approach.

Nhan Nguyen↗

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

TechEdSat 7, 10, 13, 15: Exo-brake Experiments on the ISS, First Virgin Orbit, and First Firefly-Alpha Test Flights.

The TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has been studying cube satellite re-entry technologies with a focus on Exo-Brake drag device research. An exo-atmospheric braking device, the Exo-Brake uses the tenuous upper atmosphere acting in a free molecular flow regime to enable controllable adjustment of the drag profile of the host spacecraft, currently enabling rapid disposal of small spacecraft after mission conclusion, and eventual targeted de-orbit to a desired entry point at the Von Karman line, or approximately 100km in altitude. The TES-7 mission, flown on the first successful Virgin Orbit flight January 17, 2021, was injected into a 500km, 61-degree inclination orbit, with an expected orbital lifetime of approximately ten years. After successful deployment of a unique hydrogen gas-cell inflation design ‘disposal’-type Mylar Exo-Brake intended to rapidly de-orbit the spacecraft, the maximum expected orbital lifetime of the TES-7 spacecraft was successfully reduced from ten years to 1.3 years, an 87% reduction in orbit lifetime via a passive, fuel-less system. The subsequent TES-13 mission utilized a new, less complex ‘disposal’-type Exo-Brake design made from collapsible rigid struts rather than inflated struts to reduce the engineering, construction, and safety complexities introduced by the prior hydrogen gas inflation design. The rigid strut Exo-Brake design is stowed via rotational compression and deploys using only stored spring energy once released via electronic actuator. This new rotation compression storage design has become the new Exo-Brake design standard used on TES missions thanks to its simplicity. Following on the success of this new Exo-Brake design demonstrated by TES-13, the design was further refined to enabled active manipulation of the Exo-Brake effective drag area though a winch-like system. Both the TES-10 and TES-15 spacecraft were equipped with geometrically similar Exo-Brake devices capable of such active drag modulation, with the intent of studying the operational impact of having such devices on cube satellite missions. To increase the survival time of the Exo-Brake at low altitudes and thus gain more experiment time and better guidance capability, TES-15 was equipped with a modulated Exo-Brake constructed from 3M™ Nextel™ 440 ceramic oxide fiber, the same fabric material used in the Space Shuttle TPS system, rather than Mylar. After launching on Alpha Flight 2 October 1st, 2022, Firefly’s first successful launch, TES-15 met the same modulation restrictions as TES-10, with modulation prohibited above 200km to avoid possible collision with other spacecraft. In this case, a low deployment orbit caused an extremely short mission life, which, coupled with delayed spacecraft identification, exacerbated collision concerns and caused performance data of the high-temperature Exo-Brake design to be inconclusive. As such, the Nano Orbital Workshop has taken a new approach of only conducting modulated Exo-Brake research on missions deploying below ISS altitude to avoid collision avoidance restrictions, and is working to improve spacecraft identification and location reporting techniques to increase experiment durations. Upcoming TES mission will therefore use one of two classes of Exo-Brake depending on their target altitude, as to be described in the submission.

M Murbach↗

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗

TechEdSat 7, 10, 13, 15: Exo-brake Experiments on the ISS, First Virgin Orbit, and First Firefly-Alpha Test Flights

The TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has been studying cube satellite re-entry technologies with a focus on Exo-Brake drag device research. An exo-atmospheric braking device, the Exo-Brake uses the tenuous upper atmosphere acting in a free molecular flow regime to enable controllable adjustment of the drag profile of the host spacecraft, currently enabling rapid disposal of small spacecraft after mission conclusion, and eventual targeted de-orbit to a desired entry point at the Von Karman line, or approximately 100km in altitude. The TES-7 mission, flown on the first successful Virgin Orbit flight January 17, 2021, was injected into a 500km, 61-degree inclination orbit, with an expected orbital lifetime of approximately ten years. After successful deployment of a unique hydrogen gas-cell inflation design ‘disposal’-type Mylar Exo-Brake intended to rapidly de-orbit the spacecraft, the maximum expected orbital lifetime of the TES-7 spacecraft was successfully reduced from ten years to 1.3 years, an 87% reduction in orbit lifetime via a passive, fuel-less system. The subsequent TES-13 mission utilized a new, less complex ‘disposal’-type Exo-Brake design made from collapsible rigid struts rather than inflated struts to reduce the engineering, construction, and safety complexities introduced by the prior hydrogen gas inflation design. The rigid strut Exo-Brake design is stowed via rotational compression and deploys using only stored spring energy once released via electronic actuator. This new rotation compression storage design has become the new Exo-Brake design standard used on TES missions thanks to its simplicity. Following on the success of this new Exo-Brake design demonstrated by TES-13, the design was further refined to enabled active manipulation of the Exo-Brake effective drag area though a winch-like system. Both the TES-10 and TES-15 spacecraft were equipped with geometrically similar Exo-Brake devices capable of such active drag modulation, with the intent of studying the operational impact of having such devices on cube satellite missions. To increase the survival time of the Exo-Brake at low altitudes and thus gain more experiment time and better guidance capability, TES-15 was equipped with a modulated Exo-Brake constructed from 3M™ Nextel™ 440 ceramic oxide fiber, the same fabric material used in the Space Shuttle TPS system, rather than Mylar. After launching on Alpha Flight 2 October 1st, 2022, Firefly’s first successful launch, TES-15 met the same modulation restrictions as TES-10, with modulation prohibited above 200km to avoid possible collision with other spacecraft. In this case, a low deployment orbit caused an extremely short mission life, which, coupled with delayed spacecraft identification, exacerbated collision concerns and caused performance data of the high-temperature Exo-Brake design to be inconclusive. As such, the Nano Orbital Workshop has taken a new approach of only conducting modulated Exo-Brake research on missions deploying below ISS altitude to avoid collision avoidance restrictions, and is working to improve spacecraft identification and location reporting techniques to increase experiment durations. Upcoming TES mission will therefore use one of two classes of Exo-Brake depending on their target altitude, as to be described in the submission.

Marcus Murbach↗

Simplified Applied Loads of a Transonic Truss-Braced Wing Derived from Computational Fluid Dynamics

The transonic truss-braced wing (TTBW) concept is under consideration by the NASA Advanced Air Transport Technology (AATT) project due to its potential to reduce fuel consumption of transport aircraft. To properly evaluate the TTBW concept, detailed structural modeling and subsequent test planning is underway, which requires a simplified set of discrete applied loads that simulate the distributed aerodynamic pressures. Given the unique architecture of the TTBW and its intended operation in the transonic regime, computational fluid dynamics (CFD) is the ideal approach to employ to ensure the aerodynamics of this configuration are sufficiently captured. To convert aerodynamic results into input for structural models, application of a data transfer tool, Discrete Data Transfer Between Dissimilar Meshes (DDTBDM), is presented to resolve aerodynamic pressures from CFD into single load vectors at hardpoints along both the wing and the strut. Evaluation of mapping the aerodynamic forces to hardpoints at rib and spar intersections in a structural model is performed, and the results are also compared with a linear static aeroelastic analysis. The structural responses indicate that distributing forces along only the wing and strut forward spars is insufficient for simulating the distributed aerodynamic loads. Adding moments along the forward spars improved the global response of the wing, but the point moments created unrealistic local rotations within the structure. When distributing loads along both the forward and aft spars of the wing and strut, the global response was less sensitive to the inclusion of point moments, which indicated the arrangement of point forces alone was sufficient input for structural design work and testing and provided a more continuous loading profile.

Finite Element↗

Simplified Applied Loads of a Transonic Truss-Braced Wing Derived from Computational Fluid Dynamic

The transonic truss-braced wing (TTBW) concept is under consideration by the NASA Advanced Air Transport Technology (AATT) project due to its potential to reduce fuel consumption of transport aircraft. To properly evaluate the TTBW concept, detailed structural modeling and subsequent test planning is underway, which requires a simplified set of discrete applied loads that simulate the distributed aerodynamic pressures. Given the unique architecture of the TTBW and its intended operation in the transonic regime, computational fluid dynamics (CFD) is the ideal approach to employ to ensure the aerodynamics of this configuration are sufficiently captured. To convert aerodynamic results into input for structural models, application of a data transfer tool, Discrete Data Transfer Between Dissimilar Meshes (DDTBDM), is presented to resolve aerodynamic pressures from CFD into single load vectors at hardpoints along both the wing and the strut. Evaluation of mapping the aerodynamic forces to hardpoints at rib and spar intersections in a structural model is performed, and the results are also compared with a linear static aeroelastic analysis. The structural responses indicate that distributing forces along only the wing and strut forward spars is insufficient for simulating the distributed aerodynamic loads. Adding moments along the forward spars improved the global response of the wing, but the point moments created unrealistic local rotations within the structure. When distributing loads along both the forward and aft spars of the wing and strut, the global response was less sensitive to the inclusion of point moments, which indicated the arrangement of point forces alone was sufficient input for structural design work and testing and provided a more continuous loading profile.

Finite Element↗

Structural Characterization of a TriTruss Module

The TriTruss is a novel structural module developed by researchers at NASA Langley Research Center (LaRC) that can be used in space to assemble large support structures for a variety of applications. One such application is the metering truss or primary mirror backbone support structure of an In-Space Assembled Telescope (iSAT). For the iSAT application, the TriTruss will be supporting mirror segments, payloads, and instruments, all of which require the TriTruss to have a high stiffness. Structural characterization from testing and analysis is needed to ensure the integrity of the struts that make up a TriTruss module is maintained when subjected to loads representative of the application. The test setup and loads applied to the TriTruss module as well as the analytical methods used to predict the response of the structure under conditions representative of those implemented during testing will be discussed. Also, the results obtained from testing and analysis will be summarized. The goal for the characterization study was to achieve a correlation within 10% between the test data and the analysis. Overall, the correlation varied for the struts with a few struts still having a larger error margin after further studies were conducted to improve the correlation through additional analysis.

Characterization↗

Scalability in SLA lattice through lattice orientation and hybrid frame and plate architectures

Lightweighting has been a key goal for engineers and designers, with lattice structures widely explored as the building blocks for structural components. Cellular structure-inspired lattice truss frame designs made of struts, have been extensively studied. All plate-based lattice designs have superior mechanical performance. Limits in scalability occur from formation of closed pockets limiting uv curing in processes like stereolithography (SLA). We examine hybrid frame and plate body-centered cubic-simply cubic (BCC-SC) lattices under compression. Unit cells and scaled up lattice exhibit an increase in yield stress and modulus with the addition of plates. The loading direction on the hybrid frame and plate unit cells affected the magnitude of improvement. Simulations and measurements indicated that the optimal lightweight lattice was determined to be when two plates were placed opposite each other with plates buttressing the struts, inhibiting buckling of the struts aligned with the loading direction. This lattice resulted in 63% improvement in specific modulus, a 137% improvement in specific yield point, and a 360% improvement in specific energy absorption (SEA) and the scaled up 4 × 4 × 4 scaled-up structures, showed a 107%, 148%, and 297% in specific modulus, specific yield point, and SEA, respectively A combined stretching-bending behavior was identified in optimal orientations reflecting the delayed buckling mechanism paired to a rising stress-strain curve past the elastic yield indicating bending resistance. The mass moment of inertia was found to be a key parameter correlating optimum orientation for the same number of plates added to the BCC-SC frame.

Mahan Ghosh↗

Surface modification of polymer foams using plasma

An embodiment includes a system comprising: a monolithic shape memory polymer (SMP) foam having first and second states; wherein the SMP foam includes: (a) polyurethane, (b) an inner half portion having inner reticulated cells defined by inner struts, (c) an outer half portion, having outer reticulated cells defined by outer struts, surrounding the inner portion in a plane that provides a cross-section of the SMP foam, (d) hydroxyl groups chemically bound to outer surfaces of both the inner and outer struts. Other embodiments are discussed herein.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Surface modification of polymer foams using plasma

An embodiment includes a system comprising: a monolithic shape memory polymer (SMP) foam having first and second states; wherein the SMP foam includes: (a) polyurethane, (b) an inner half portion having inner reticulated cells defined by inner struts, (c) an outer half portion, having outer reticulated cells defined by outer struts, surrounding the inner portion in a plane that provides a cross-section of the SMP foam, (d) hydroxyl groups chemically bound to outer surfaces of both the inner and outer struts. Other embodiments are discussed herein.

Nash, Landon D.↗

Automated analysis of lattice structures using computed tomography

Systems, methods, and computer-readable media for evaluating a set of computed tomography data associated with a lattice structure. The lattice structure may be additively manufactured. The computed tomography data may be segmented using a filter for identifying blob-like structures to identify nodes present within the lattice structure. A three-dimensional path traversal is applied to volumetric data to identify a plurality of struts within the lattice structure that are compared to corresponding struts within a set if three-dimensional mesh data of the lattice structure to identify defective struts. Further, two-dimensional slices may be extracted from each of the computed tomography data and the mesh data and compared to identify one or more inconsistencies indicative of defects within the lattice structure.

Schiefelbein, Bryan E.↗

Thermal management for a motor feeder

Provided are embodiments for a feeder cooling tube, a system and method for performing thermal management. Embodiments include a feeder cooling tube having an inner tube arranged to define a path to flow a fluid through a length of the inner tube, wherein the fluid is provided to remove heat, and an outer tube arranged to enclose the inner tube which defines an area. Embodiments also include one or more feeder cables arranged between the inner tube and the outer tube, and a plurality of cooling struts, wherein each cooling strut of the plurality of cooling struts extends from a surface of the inner tube to a surface of the outer tube.

Pal, Debabrata↗

Automated analysis of lattice structures using computed tomography

Systems, methods, and computer-readable media for evaluating a set of computed tomography data associated with a lattice structure. The lattice structure may be additively manufactured. The computed tomography data may be segmented using a filter for identifying blob-like structures to identify nodes present within the lattice structure. A three-dimensional path traversal is applied to volumetric data to identify a plurality of struts within the lattice structure that are compared to corresponding struts within a set if three-dimensional mesh data of the lattice structure to identify defective struts. Further, two-dimensional slices may be extracted from each of the computed tomography data and the mesh data and compared to identify one or more inconsistencies indicative of defects within the lattice structure.

Schiefelbein, Bryan E.↗

Test capsules for measuring a change in at least one property of a material, and related methods

A test capsule for measuring at least one property of a material exposed to nuclear radiation comprises a lattice structure configured to exhibit a change in at least one property responsive to exposure to nuclear radiation. The lattice structure comprises a first strut and a second strut connected to the first strut at a node. Related test capsules and methods are also described.

Roach, Robert A.↗

Microstructure‐Informed Analysis Framework for Lattice Structures: Guiding Topology‐Material Synergy in Titanium Alloys

In this work we discuss a microstructure‐informed analysis framework for lattice structures that maps the material's microstructural response to guide topology selection and mechanical performance optimization. By coupling geometrical topology with intrinsic material behavior, we demonstrate how anisotropic microstructural response can inform the design of optimized lattice structures. To illustrate this concept, we focus on two distinct classes of titanium alloys: Ti5553 (Ti‐5Al‐5Mo‐5V‐3Cr wt%), which exhibits a predominantly ‐phase microstructure, and Ti64 (Ti‐6Al‐4V wt%), which features a dual‐phase structure. These alloys exhibit markedly different mechanical responses under multiaxial loading in “fully dense” solid form. The strut‐level stress analysis of these alloys reveals how specific microstructural characteristics can guide the selection of appropriate lattice topologies. Two representative lattice configurations, one stretching‐dominated and one bending‐dominated, are evaluated under identical loading conditions to explore how microstructure‐driven design can lead to topology choices that are better suited to accommodate shear or other critical local stress states, thereby enhancing mechanical performance. A strut‐level mechanics‐based analysis is performed to evaluate shear stress distribution and highlight the role of topology‐microstructure synergy and compatibility in determining overall lattice behavior. The findings emphasize the importance of designing structures that are both load‐aware and microstructure‐responsive, enabling more effective material utilization in advanced engineering applications.

36 MATERIALS SCIENCE↗

Physical Models from Physical Templates Using Biocompatible Liquid Crystal Elastomers as Morphologically Programmable Inks For 3D Printing

Advanced manufacturing has received considerable attention as a tool for the fabrication of cell scaffolds however, finding ideal biocompatible and biodegradable materials that fit the correct parameters for 3D printing and guide cells to align remain a challenge. Herein, a photocrosslinkable smectic-A (Sm-A) liquid crystal elastomer (LCE) designed for 3D printing is presented, that promotes cell proliferation but most importantly induces cell anisotropy. The LCE-based bio-ink allows the 3D duplication of a highly complex brain structure generated from an animal model. Vascular tissue models are generated from fluorescently stained mouse tissue spatially imaged using confocal microscopy and subsequently processed to create a digital 3D model suitable for printing. The 3D structure is reproduced using a Digital Light Processing (DLP) stereolithography (SLA) desktop 3D printer. Synchrotron Small-Angle X-ray Diffraction (SAXD) data reveal a strong alignment of the LCE layering within the struts of the printed 3D scaffold. The resultant anisotropy of the LCE struts is then shown to direct cell growth. This study offers a simple approach to produce model tissues built within hours that promote cellular alignment.

3D cell culture↗

Guenter Tulip Filter Retrieval Experience: Predictors of Successful Retrieval

We report our experience with Guenter Tulip filter placement indications, retrievals, and procedural problems, with emphasis on alternative retrieval techniques. We have identified 92 consecutive patients in whom a Guenter Tulip filter was placed and filter removal attempted. We recorded patient demographic information, filter placement and retrieval indications, procedures, standard and nonstandard filter retrieval techniques, complications, and clinical outcomes. The mean time to retrieval for those who experienced filter strut penetration was statistically significant [F(1,90) = 8.55, p = 0.004]. Filter strut(s) IVC penetration and successful retrieval were found to be statistically significant (p = 0.043). The filter hook-IVC relationship correlated with successful retrieval. A modified guidewire loop technique was applied in 8 of 10 cases where the hook appeared to penetrate the IVC wall and could not be engaged with a loop snare catheter, providing additional technical success in 6 of 8 (75%). Therefore, the total filter retrieval success increased from 88 to 95%. In conclusion, the Guenter Tulip filter has high successful retrieval rates with low rates of complication. Additional maneuvers such as a guidewire loop method can be used to improve retrieval success rates when the filter hook is endothelialized.

62 RADIOLOGY AND NUCLEAR MEDICINE↗