Results for “Supportability” — Page 18

DOE OSTI2026

Material Control & Accounting Statistical Test Modeling Supporting the Low Enriched Fuel Fabrication Facility Using F3M and MAPIT

This report covers the application of the TRi-structural ISOtropic (TRISO) fuel fabrication facility material control & accounting (MC&A) modeling capability developed by Sandia National Laboratories (SNL) under the U.S. Department of Energy (DOE) Materials Protection, Accounting, and Control Technologies (MPACT) program to support the development of MC&A approaches for the Low Enriched Fuel Fabrication Facility (LEFFF) at Los Alamos National Laboratory (LANL).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Development of Large Bore Rabbit Capsules in Support of BWR Cladding Irradiations in HFIR

The High Flux Isotope Reactor (HFIR) is an ideal tool for materials irradiation testing because of its intense steady-state neutron flux. Many programs take advantage of HFIR’s central flux trap for irradiation experiments using capsules, also known as rabbits, to support advanced materials development and reactor design. The facility that makes up the HFIR flux trap has recently undergone a design change that increases the HFIR primary coolant volumetric flow rate by removing restrictions in the system. As a result, the usable cross-sectional area within the facility increased, opening the door to increase the cross-sectional area of the rabbit capsules that fill the facility. This report documents a new large-diameter rabbit housing that increases the usable volume within the rabbit capsule by 22.6%. However, challenges arise with increasing the capsule size, such as establishing a new maximum capsule operating pressure and determining the thermal-hydraulic characteristics. This report addresses those challenges with previously adopted HFIR safety methods. The rupture pressure of the rabbit housings is demonstrated while verifying that capsule swelling during and after rupture will not block coolant flow. Then, a safety factor is applied to ascertain an administrative operating pressure. Additionally, the thermal-hydraulic performance of the HFIR facility filled with large-diameter rabbit capsules is shown to not violate previously determined safety criteria. Next, heat transfer coefficients are determined for use in design calculations. Furthermore, this report gives an example of internal configurations for the new, larger rabbit capsules that use relevant boiling water reactor (BWR) cladding geometry. Finally, this report documents an example thermal design performance for a rabbit capsule containing six gauge-curved tensile tube specimens. The thermal performance gives predicted temperature distributions within the capsule and shows the expected temperature of the passive thermometers for post-irradiation temperature comparisons.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2025

Development of Large Bore Rabbit Capsules in Support of BWR Cladding Irradiations in HFIR

The High Flux Isotope Reactor (HFIR) is an ideal tool for materials irradiation testing because of its intense steady-state neutron flux. Many programs take advantage of HFIR’s central flux trap for irradiation experiments using capsules, also known as rabbits, to support advanced materials development and reactor design. The facility that makes up the HFIR flux trap has recently undergone a design change that increases the HFIR primary coolant volumetric flow rate by removing restrictions in the system. As a result, the usable cross-sectional area within the facility increased, opening the door to increase the cross-sectional area of the rabbit capsules that fill the facility. This report documents a new large-diameter rabbit housing that increases the usable volume within the rabbit capsule by 22.6%. However, challenges arise with increasing the capsule size, such as establishing a new maximum capsule operating pressure and determining the thermal-hydraulic characteristics. This report addresses those challenges with previously adopted HFIR safety methods. The rupture pressure of the rabbit housings is demonstrated while verifying that capsule swelling during and after rupture will not block coolant flow. Then, a safety factor is applied to ascertain an administrative operating pressure. Additionally, the thermal-hydraulic performance of the HFIR facility filled with large-diameter rabbit capsules is shown to not violate previously determined safety criteria. Next, heat transfer coefficients are determined for use in design calculations. Furthermore, this report gives an example of internal configurations for the new, larger rabbit capsules that use relevant boiling water reactor (BWR) cladding geometry. Finally, this report documents an example thermal design performance for a rabbit capsule containing six gauge-curved tensile tube specimens. The thermal performance gives predicted temperature distributions within the capsule and shows the expected temperature of the passive thermometers for post-irradiation temperature comparisons.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Neutronics Evaluations in Support of the Preliminary Design of the Service Cell Storage Pits for the Second Target Station

This report provides a summary of a series of neutronics calculations to support the preliminary design of the service cell storage pits for the Second Target Station.

Ghoos, Kristel [Oak Ridge National Laboratory (ORN↗

DOE OSTI2026

Machine Tool Metrology in support of carbide insert production

In the context of lab modernization, careful consideration must be given to existing technologies, processes, and knowledge to support the ongoing production, maintenance, and improvement of products for the nuclear enterprise. This consideration often involves analyzing manufacturing processes both to pursue modernization or automation and to ensure the ability to maintain manufacturing capability.

42 ENGINEERING↗

DOE OSTI2026

Analysis of Tank 38H (HTF-38-26-16, -17), Tank 43H (HTF 43-26-18, -19) and Tank 22 (HTF-22-26-20, -21) Samples for Support of the Enrichment Control and Corrosion Control Programs

Savannah River National Laboratory (SRNL) analyzed samples from Tank 38H, Tank 43H and Tank 22H to support the Enrichment Control Program (ECP) and Corrosion Control Program (CCP). The results indicate the concentrations of most soluble species in the Tank 38H surface sample are ~ 76% of the concentrations in the previous Tank 38H surface sample. The current Tank 38H subsurface sample is a clear solution with soluble species that are ~ 70% of the concentrations in the previous Tank 38H subsurface. Significant differences in the concentrations of major components between the current Tank 38H surface and subsurface samples indicate stratification of solution species between these two locations within Tank 38H.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Coalition for Community-Supported Affordable Geothermal Energy Systems (C2SAGES)

The C2SAGES project evaluated the feasibility of a community geothermal system for the planned Windy Ridge affordable housing development in Hinesburg, Vermont. Led by GTI Energy with Vermont Gas Systems, LN Consulting, NREL, and Frontier Energy, the work assessed technical design, energy performance, costs, business models, community engagement, maintenance, workforce development, and permitting. The proposed system was designed to serve 100% of the development’s heating, cooling, and domestic hot water loads. Compared with a baseline using air-source heat pumps and natural gas water heating, the geothermal system was estimated to reduce HVAC and domestic hot water energy use by about 45% to 48%, lower operating and maintenance costs, and reduce 30-year life-cycle costs by 37% for Phase 1 and 10% for Phase 2. Technical testing and modeling indicated that the Windy Ridge site is suitable for a community-scale geothermal system. The project also developed borehole field layouts, piping concepts, pump house designs, controls, maintenance plans, and supporting engineering drawings. The business model analysis found that first cost, ownership structure, and customer affordability remain major deployment challenges. Utility-led maintenance and operation were viewed favorably, but traditional utility cost-recovery models may require subsidy or revised financing structures to be practical for affordable housing. Community engagement highlighted the need for clear public education, transparent financing, reliable long-term maintenance, trained technicians, and the potential to pair geothermal systems with weatherization. Overall, the report concludes that community geothermal is technically feasible and offers meaningful energy, emissions, and life-cycle cost benefits, but broader deployment will depend on workable financing models and workforce readiness.

15 GEOTHERMAL ENERGY↗

DOE OSTI2026

Cooperative Support of the Fermilab Site’s Natural Areas and Related Programs (CRADA Final Report)

Under the prime contract with the Department of Energy, Fermi Research Alliance, LLC (FRA) is responsible for effective stewardship of the Fermi National Accelerator Laboratory (Fermilab) 6,800-acre site, to assure that Fermilab is renewed and enhanced to meet future mission needs. As the steward of the Fermilab site, FRA is responsible for maintaining the natural areas for the site (e.g., prairie restoration sites, woodlands, etc.), which are essential for protecting the health and safety of personnel working on or visiting the site, while supporting the scientific and educational missions of Fermilab. Fermilab Natural Areas (FNA) is a not-for-profit corporation organized and existing under the laws of the State of Illinois. FNA was founded in 2006 and incorporated in 2008 for the purposes of studying, conserving, and restoring the Fermilab Site’s natural areas in a manner consistent with the science mission of Fermilab and enhancing the awareness and visibility of the natural amenities of Fermilab to neighboring communities.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2026

Comparative Assessment of Battery Carbon Footprint Calculation Frameworks to Support U.S. Battery Manufacturing

A “battery passport” is a digital record that provides comprehensive information about an individual battery across its life cycle. This concept has been introduced by Battery Regulation (EU) 2023/1542 [1], which applies to batteries for electric vehicles (EVs), industrial batteries with a capacities greater than 2 kWh, and batteries for light means of transport (LMT) greater than 2kWh sold in the European Union (EU) market – impacting manufacturers and exporters across multiple jurisdictions globally. Among its reporting mandates, a key feature of battery passports is the requirement for a carbon footprint (CF) calculation methodology supported by enhanced data granularity to enable traceable and verifiable CF results. While no other jurisdictions have yet adopted formal battery passport requirements like the EU’s, some are developing CF calculation methods to comply with the EU Battery Regulation or are creating CF-related regulations that could evolve in a similar direction, reflecting the growing importance of battery CF guidelines for manufacturers seeking to remain competitive in global markets.

Zhang, Jingyi [Argonne National Laboratory (ANL), ↗

DOE OSTI2025

UN Synthesis, Fabrication, and Characterization and UC Oxidation Study in support of Advanced LEU Fuel Concepts

Uranium nitride and carbide-based fuels are proposed for use in advanced LEU fuel systems. This report details recent development work to study synthesis, sintering and fabrication methods for single phase UN in monolithic geometries. These samples were intended to support a variety of irradiation testing conditions by tailoring enrichment, geometry, and compositional requirements. Two methods were under evaluation for synthesizing uranium nitride powder – carbothermic reduction-nitridation (CTR-N) of UO 2 powder feedstock and hydride-dehydride/nitridation (HDN) of uranium metal feedstock. Pellets were fabricated from powder feedstocks via conventional pressing and sintering methods. As-fabricated feedstocks and pellets were evaluated via X-ray diffraction (XRD) for phase purity and sintered materials were characterized for density. Both the CTR N and the HDN methods were successfully demonstrated as an effective process for fabricating phase pure UN. Additionally, results from machining efforts for UN are detailed. This report also contains information on a study trying to elucidate the oxidation mechanisms of sintered uranium carbide samples fabricated from feedstock synthesized via an arc-melting method.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

OC6 Project Phase IV: Validation of Numerical Models for Novel Floating Offshore Wind Support Structures

The fourth phase of the Offshore Code Comparison, Collaboration, Continued, with Correlation and unCertainty (OC6) aims to assess the ability of the tools to model a novel floating wind design. The design that was selected for this project is the TetraSpar designed by Stiesdal Offshore Technologies. The platform is a unique design that features a spar like stability with a very low center of gravity, but does not require deep-water ports. This combination is achieved with a system made of two separate steel structures, a hull at the water’s surface that supports the wind turbine tower, and a keel that is suspended below the main body. This lower keel has a very high density and drives the total platform’s low center of gravity. Scaled model tests of the TetraSpar design were performed in 2018-2019 by the University of Maine. The tests were performed with 1:43 Froude scaling. The data collected in the model tests provide a detailed description of the response of the platform in various controlled and relatively well understood conditions. Comparison with these data provides a good opportunity for validation of numerical models. The OC6 Phase IV work will focus on the specific parameters used in these scaled model tests. The load cases (LC) considered in this project are as follows: LC 1.X - Equilibrium and Static Offset Tests LC 2.X - Platform Free Decays LC 3.X - Turbine Thrust (Wind Only) LC 4.X - Regular and Irregular Waves (Wave only) LC 5.X - Combined Wind and Wave Loading

17 WIND ENERGY↗

DOE OSTI2025

Assessing the limitations of commercial sensors and models for supporting marine carbon dioxide removal monitoring: a case study

Several unknowns remain surrounding marine Carbon Dioxide Removal (mCDR) monitoring, reporting, and verification (MRV) practices and capabilities. Current in-situ sensor technology is limited (primarily pH and pCO 2 ), requiring calculations and assumptions to estimate changes in carbonate chemistry parameters, including total alkalinity (TA). Considering that cost, energy consumption, and accuracy of commercial sensors can vary by orders of magnitude, understanding how well existing sensors perform in an mCDR context is important for this emerging community. Likewise, documenting sensor limitations and how relatively simple models can optimize sensor deployments will improve MRV efforts and support protocol development. Here we (1) compare performance a variety of commercially available sensors in a blind mesocosm experiment simulating ocean alkalinity enhancement (OAE), and how sensor performance impacted carbonate chemistry estimates; (2) evaluate if sensors can distinguish the OAE signal from natural variability during a small scale OAE field test in Sequim Bay, WA, USA, and (3) use an idealized ocean biogeochemistry model to explore optimal sensor network design based on (1) and (2). Our mesocosm results indicate that correctly constraining pH uncertainty will be critical for accurate TA estimates with current sensor technology compared to the less impactful variation caused by uncertainty in pCO 2 (pH data that are presented throughout are reported on the total scale (pH T ) unless otherwise noted). Our pilot field test demonstrated that sensors were capable of distinguishing mCDR signatures from natural variability under optimal real-world conditions. Idealized modeling simulations of the field test showed that a range of sparse and dense (3 to 100) sensors sampling areas of detectable increases will underestimate the net change in surface pH by at least 35–55%, at both realistic and highly elevated alkalinity input levels. We also highlight the limitations of current sensing technology for MRV, and the importance of ocean biogeochemistry models as critical tools for predicting when and where mCDR signals will be detectable using available sensors. Overall, our findings suggest that commercially available pCO 2 sensors and some pH sensors will form an important backbone for mCDR MRV tasks, though complete MRV characterization will require these data to be used in combination with other tools.

OAE↗

DOE OSTI2025

Effect of Fe on Co-Based SiO2Al2O3 Mixed Support Catalyst for Fischer–Tropsch Synthesis in 3D-Printed SS Microchannel Microreactor

This research explores the effect of a composite support of SiO2 and Al2O3 with Fe and Co incorporated as catalysts for Fischer–Tropsch synthesis (FTS) using a 3D-printed stainless steel (SS) microchannel microreactor. Two mesoporous catalysts, FeCo/SiO2Al2O3 and Co/SiO2Al2O3, were synthesized via a one-pot (OP) method and extensively characterized using N2 physisorption, XRD, SEM, TEM, H2-TPR, TGA-DSC, FTIR, and XPS. H2-TPR results revealed that the synthesis method significantly affected the reducibility of metal oxides, thereby influencing the formation of active FTS sites. SEM-EDS and TEM further revealed a well-defined hexagonal matrix with a porous surface morphology and uniform metal ion distribution. FTS reactions, carried out in the 200–350 °C temperature range at 20 bar with a H2/CO molar ratio of 2:1, exhibited the highest activity for FeCo/SiO2Al2O3, with up to 80% CO conversion. Long-term stability was evaluated by monitoring the catalyst performance for 30 h on stream at 320 °C under identical reaction conditions. The catalyst was initially active for the methanation reaction for up to 15 h, after which the selectivity for CH4 declined. Correspondingly, the C4+ selectivity increased after 15 h of time-on-stream, indicating a shift in the product distribution toward longer-chain hydrocarbons. This trend suggests that the catalyst undergoes gradual activation or restructuring under reaction conditions, which enhances chain growth over time. The increase in C4+ products may be attributed to the stabilization of the active sites and suppression of methane or light hydrocarbon formation.

Biochemistry & Molecular Biology↗

DOE OSTI2024

Cell-Free Screening, Production and Animal Testing of a STI-Related Chlamydial Major Outer Membrane Protein Supported in Nanolipoproteins

Background: Vaccine development against Chlamydia, a prevalent sexually transmied infection (STI), is imperative due to its global public health impact. However, significant challenges arise in the production of effective subunit vaccines based on recombinant protein antigens, particularly with membrane proteins like the Major Outer Membrane Protein (MOMP). Methods: Cellfree protein synthesis (CFPS) technology is an aractive approach to address these challenges as a method of high-throughput membrane protein and protein complex production coupled with nanolipoprotein particles (NLPs). NLPs provide a supporting scaffold while allowing easy adjuvant addition during formulation. Over the last decade, we have been working toward the production and characterization of MOMP-NLP complexes for vaccine testing. Results: The work presented here highlights the expression and biophysical analyses, including transmission electron microscopy (TEM) and dynamic light scaering (DLS), which confirm the formation and functionality of MOMP-NLP complexes for use in animal studies. Moreover, immunization studies in preclinical models compare the past and present protective efficacy of MOMP-NLP formulations, particularly when co-adjuvanted with CpG and FSL1. Conclusion: Ex vivo assessments further highlight the immunomodulatory effects of MOMP-NLP vaccinations, emphasizing their potential to elicitrobust immune responses. However, further research is warranted to optimize vaccine formulations further, validate efficacy against Chlamydia trachomatis, and beer understand the underlying mechanisms of immune response.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

Raw Data for: Ultra-Confined Environments May Restrict the Possible Configurations of Supported Metal Complexes

Raw NMR data (1D 2H spectrum and pseudo-2D 2H CODEX spectra) in Bruker topspin format. Raw DRIFTS IR data as text files. Results from the DFT potential energy surface scans (coordinates are in the supporting information of the main publication). Raw BET nitrogen physisorption isotherms and the determined more size distributions.

Perras, Frederic A [Ames National Laboratory]↗

DOE OSTI2026

Wind and Temperature Consensus at Horn Point, HU-Beltsville, Piney Run (Maryland) in support of CoURAGE

The Maryland Department of the Environment (MDE) operates a ground-based atmospheric profiling network consisting of collocated radar wind profilers (RWP) and radio acoustic sounding systems (RASS) as part of its Ambient Air Monitoring Program. This network provides continuous observations of wind and temperature structure in the lower troposphere to support air quality forecasting, regulatory analysis, and atmospheric research. The network currently includes three fixed sites across Maryland: Horn Point (HP, lower eastern shore) [38.587525°,-76.141006°], Howard University-Beltsville (HUB, central Maryland) [39.055277°, -76.878632°], and Piney Run (PR, western Maryland) [39.705950°, -79.012000°] The network is designed to capture regional variability in atmospheric transport and boundary-layer processes. These systems measure vertical profiles of horizontal wind speed and direction using Doppler radar techniques, with observations typically spanning from ~100 m above ground level up to approximately 2.5–4 km. Measurements are derived from the Doppler shift of backscattered electromagnetic signals, enabling retrieval of wind vectors at multiple altitudes with high temporal resolution (e.g., 30-minute averages reported every 6 minutes). Each radar wind profiler is paired with a Radio Acoustic Sounding System (RASS) to provide profiles of virtual temperature in the lower atmosphere (~100–200 m AGL) by measuring the propagation speed of acoustic waves. Together, the RWP/RASS system yields a coupled data set of thermodynamic and kinematic atmospheric structure, including additional parameters such as vertical velocity, radial velocity, signal-to-noise ratio, and spectral width for advanced analysis. There are two types of files for each station: wind data (files with a "w" prefix) and virtual temperature RASS data (files with a "t" prefix). The wind data files are in the format wYYDDD.cns, where YY is the 2-digit year and DDD is the day of the year. The RASS virtual temperature data files are in the format tYYDDD.cns. Each record has the following header structure: Line 1 : Station Name RASS files Line 2 : RASS rev DeTect_2.0, WINDS files Line 2 : WINDS rev ATI 5.1 Line 3 : N latitude, W longitude, and site elevation (m) Line 4 : Date and begin time of consensus: yy mm dd hh mn ss plus # minutes to add to get UTC Line 5 : Consensus averaging time (minutes); number of beams; number of range gates Line 6 : Number of records required to make consensus (num) total number of records (tot) and the consensus window size (m/s) in the format: num:tot (window) RASS files Line 7 : no. of coded cells, no. of spec, pulse width (ns), and inter-pulse period (µs), WINDS files Line 7 : No. of coded cells, no. of spectra, pulse width (ns), and inter-pulse period (µs), each with a pair of values: first value is for oblique beams, second for vertical RASS files Line 8 : Full scale Doppler value (m/s) Delay to first gate (ns) Number of gates Spacing of gates (ns), WINDS files Line 8 : Full scale Doppler velocity (m/s), oblique and vertical Vertical correction applied to oblique beams? (0 = no, 1 = yes) Delay to first gate (ns), oblique and vertical Number of gates, oblique and vertical Spacing of gates (ns), oblique and vertical Line 9 : Azimuth and elevation (9s indicate vertical beam not used) RASS files Line 10, values : HT = Height above ground (km), T = Uncorrected virtual temperature consensus (deg C), Tc = Corrected virtual temperature consensus (deg C), W = Vertical wind consensus (9s indicate vertical beam not used, w-component, positive upward, m/s), CNT = Number of records that made consensus (for the 3 values in same order), SNR = Average signal to noise ratio (dB) of records in consensus (same order) WINDS files Line 10, values : HT = Height above ground (km), SPD = Wind speed (m/s), DIR = Wind direction (deg E of N from N), RAD = Radial velocities for each beam (m/s) in order given in azimuth and elevation line (positive toward radar; 9s indicate vertical beam not used, CNT = Number of records that made consensus, SNR = Average signal to noise ratio (dB) of records in consensus

{"wind speed and direction",temperature}↗

DOE OSTI2025

Supporting Information - How Can Crop Production Adapt to growing groundwater restrictions in the West?

Abstract This data plan outlines the structure and content of datasets generated and utilized in the research presented in the manuscript abstract. Groundwater overdraft has led to serious water supply issues in the US West. Most western states manage groundwater use through a permitting system, but California has only recently begun to restrict groundwater use statewide with the 2014 passage of groundwater restrictions which target the elimination of groundwater overdraft practices by 2042. With groundwater extraction curtailed, crop production in the US West (a $95 billion industry annually) will be affected, and appropriate response strategies will be needed to ensure minimal disruption to food production and the regional economy. In this paper, we explore the adoption of alternative adaptive responses: (a) deficit irrigation; (b) switching to less water-intensive crops; (c) changing the extent of irrigated land (including fallowing); and (d) geographically shifting crop production. Employing an integrated modeling approach, we explicitly capture the interactions and feedbacks between local hydrology, changes in crop yields, crop and land use decision-making, changes in crop prices, and regional shifts in crop production. We find that the optimal adaptive response is spatially heterogeneous and comprises a portfolio of strategies. Southwestern states and California will be the most impacted by groundwater restrictions. The optimal responses in these states are to both adopt deficit irrigation strategies and reduce a portion of their irrigated croplands, resulting in a shift in crop production to northwestern states with a larger supply of water. The datasets detailed in this repository represent the output from these integrated models, specifically designed to support the analysis and visualization presented in the manuscript and supplemental information. These datasets, used in conjunction with the scripts available at our associated GitHub repository (https://github.com/pches/Femeena_etal_How_can_crop_production_adapt), enable the reproduction of figures and facilitate a comprehensive understanding of the optimal adaptive strategies in agriculture for mitigating water stress under varying groundwater extraction scenarios, as outlined in the abstract.

DNDCe↗

DOE OSTI2025

Supporting Information - How Can Crop Production Adapt to growing groundwater restrictions in the West?

Abstract This data plan outlines the structure and content of datasets generated and utilized in the research presented in the manuscript abstract. Groundwater overdraft has led to serious water supply issues in the US West. Most western states manage groundwater use through a permitting system, but California has only recently begun to restrict groundwater use statewide with the 2014 passage of groundwater restrictions which target the elimination of groundwater overdraft practices by 2042. With groundwater extraction curtailed, crop production in the US West (a $95 billion industry annually) will be affected, and appropriate response strategies will be needed to ensure minimal disruption to food production and the regional economy. In this paper, we explore the adoption of alternative adaptive responses: (a) deficit irrigation; (b) switching to less water-intensive crops; (c) changing the extent of irrigated land (including fallowing); and (d) geographically shifting crop production. Employing an integrated modeling approach, we explicitly capture the interactions and feedbacks between local hydrology, changes in crop yields, crop and land use decision-making, changes in crop prices, and regional shifts in crop production. We find that the optimal adaptive response is spatially heterogeneous and comprises a portfolio of strategies. Southwestern states and California will be the most impacted by groundwater restrictions. The optimal responses in these states are to both adopt deficit irrigation strategies and reduce a portion of their irrigated croplands, resulting in a shift in crop production to northwestern states with a larger supply of water. The datasets detailed in this repository represent the output from these integrated models, specifically designed to support the analysis and visualization presented in the manuscript and supplemental information. These datasets, used in conjunction with the scripts available at our associated GitHub repository (https://github.com/pches/Femeena_etal_How_can_crop_production_adapt), enable the reproduction of figures and facilitate a comprehensive understanding of the optimal adaptive strategies in agriculture for mitigating water stress under varying groundwater extraction scenarios, as outlined in the abstract.

DNDCe↗