Search NASA⌕ Search

SEARCH · Search NASA

Results for “TENSILE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical rolling and annealing of wire-arc additively manufactured stainless steel plates

Thin walls of 304L stainless steel were fabricated by wire-arc additive manufacturing (WAAM) followed by post build thermomechanical processing to modify the as built microstructure and properties. The walls were made using a high-deposition-rate robotically controlled gas-metal arc welding system and were characterized using optical microscopy and tensile tested for mechanical properties. Post processing consisted of mechanical rolling the walls to 25% and 40% strains, followed by annealing at 1050°C to demonstrate a wide range of properties. Results show that WAAM can be used to build custom sized semi-finished parts or blanks that can later be thermomechanically processed to increase strength and ductility through recrystallization of the as built microstructure, and/or processed into desired shapes with improved mechanical properties.

304L stainless steel↗
DOE OSTI2021

Capillary flow in UHPFRC with synthetic fibers, under high tensile stresses

A novel Ultra High-Performance Fiber Reinforced Concrete (UHPFRC) mix with synthetic fibers and a low clinker matrix, henceforth referred to as PE-UHPFRC, has been developed for structural applications. It exhibits a high tensile elastic limit above 7 MPa, a tensile strength of more than 10 MPa, and a very high tensile hardening domain of above 3.5%. In order to effectively use this material, its protective properties have been investigated on the basis of the effect of tensile deformation and subsequent cracking on water transport properties, for a wide range of tensile strain. A special setup was developed to measure the capillary absorption of liquids while the specimen is under tension. The results show a considerable reduction in capillary absorption in case of PE-UHPFRC compared with Strain Hardening Cement-based Composites (SHCC). Moreover, the results highlight the considerable effect of the onset of cracking on capillary absorption.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The role of specimen size and grain boundary characteristics in the yield strength of tungsten in microtensile tests

To effectively use the measured properties from small-scale tensile tests for bulk material performance predictions, it is essential to understand the threshold of specimen size-effect strengthening and the interaction between dislocations and microstructures within miniaturized specimens. This study uses pure tungsten to investigate the size effect in terms of specimen size, grain size, and grain boundary characteristics relative to the yield strength of tungsten at room temperature. We evaluate the transition from miniaturized specimen properties to bulk properties and the deformation behavior through small-scale tensile tests of three specimen sizes (large: 80 × 100 × 233 µm³; medium: 7 × 7 × 18 µm³; and small: 2 × 2 × 5 µm³). The testing results reveal that the small and medium specimens exhibit high yield strength with ductile behavior, while the large specimens exhibit brittle failure, consistent with the room temperature strength of tungsten, indicating bulk behavior. We further explore the specimen size-effect sensitivity to yield stress and the scaling relationship between yield strength and the number of grains involved in the deformation. A power-law relationship with the exponent value of approximately -0.5 was found in the yield strength–grain number scaling, implying the Hall-Petch like behavior. A minimum of 7–17 effective grain boundaries across the tensile gauge dimension is required to accurately measure bulk properties.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails

Highlights: • An in-process interlayer reinforcement approach for 3D concrete printing was proposed through the concurrent deposition of U-nails. • Significant strength and toughness improvement was achieved for U-nail reinforced 3D-printed concrete. • The bridge linking effect and dowel action of U-nails were analysed. • Response surface method were utilised to quantify the effects of U-nails on the interlayer bonding behaviour. 3D concrete printing has tremendous potential for construction manufacturing; however, weak interface bonding between adjacent layers remains a well-known issue that affects the mechanical properties of printed structures. The layers introduce anisotropy and reduce the capacity to resist tensile and shear loads. Reinforcements, inserted perpendicular to the printed layers to traverse the interfaces, can improve these limitations, but the insertion of reinforcements is difficult to achieve in practice, and there are few published studies exploring appropriate methods. This study presents a promising approach using U-shaped nails inserted into concrete during the printing process. The bridging effect and dowel action of the applied U-nails are visualised and analysed to elucidate the toughness improvement. The ultimate tensile strength and shear strength of 3D printed concrete are significantly increased by 145.0% and 220.0%, respectively. U-nails with a filament thickness of 2–2.5 mm are recommended to yield optimal improvement in the interlayer strength.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predicting defects in laser powder bed fusion using in-situ thermal imaging data and machine learning

Variation in the local thermal history during the Laser Powder Bed Fusion (LPBF) process in Additive Manufacturing (AM) can cause micropore defects, which add to the uncertainty of the mechanical properties (e.g., fatigue life, tensile strength) of the built materials. In-situ sensing has been proposed for monitoring the AM process to minimize defects, but successful minimization requires establishing a quantitative relationship between the sensing data and the porosity, which is particularly challenging with a large number of variables (e.g., laser speed, power, scan path, powder property). Physics-based modeling can simulate such an in-situ sensing-porosity relationship, but it is computationally costly. In this work, we develop Machine Learning (ML) models that can use in-situ thermographic data to predict the micropore of LPBF stainless steel materials. This work considers two identified key features from the thermal histories: the time above the apparent melting threshold ($\tau$) and the maximum radiance ( T max ). These features are computed, stored for each voxel in the built material, and then used as inputs. The binary state of each voxel, either defective or normal, is the output. Different ML models are trained and tested for the binary classification task. In addition to using the thermal features of each voxel to predict its own state, the thermal features of neighboring voxels are also included as inputs. This is shown to improve the prediction accuracy, which is consistent with thermal transport physics around each voxel contributing to its final state. Among the models trained, the F1 scores on test sets reach above 0.96 for Random Forests. Feature importance analysis based on the ML models shows that T max is more important to the voxel state than $\tau$ . The analysis also finds that the thermal history of the voxels above the present voxel is more influential than those beneath it. Our study significantly extends the capability of using in-situ thermographic data to predict porosity in LPBF materials. Finally, since ML models are fast, they may play integral roles in the optimization and control of such AM technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A comprehensive review on valorization of chestnut processing wastes into bio‐based composites and bioplastics

Abstract This review examines the characterization and utilization of chestnut processing wastes (35%) in the production of bioplastics and biocomposites. In this review, a Web of Science search without any publishing year restriction on the biochemical compositions of all the components of Castanea sativa . The obtaining of bioplastics and biocomposites based on C. sativa was reviewed. First, it highlights the biochemical composition and antioxidant properties of chestnut fruit, shell, burrs, leaves, flowers, and wood focusing on the most important compounds, such as phenolic acids, flavonoids, carbohydrates, Klason lignin, cellulose, and glucan, which can enhance the properties of these materials. Then the review covers using several chestnut extracts and fillers in bioplastics production through solvent casting technique. The mechanical, structural, bioactive properties, and moisture content were optimized through the composition and production. The color, UV absorption, antioxidant, and antimicrobial activity were also discussed. Biocomposites reinforced with chestnut burs, shells, or wood flour increased the intended properties. The enhancements in tensile strength, elastic modulus, and the effects of a pre‐treatment were evaluated. Additionally, it discusses material recovery, recycling, and reuse, particularly how it affects the biodegradability of composites incorporating chestnut waste residues. Highlights Chestnut fruit, shells, and burrs are rich in starch, lignin, and cellulose. The waste of chestnut processing can be used in bioplastics and biocomposites. Chestnut‐based films and biocomposites exhibit promising mechanical properties. The antimicrobial activity, making films, and composites proper for food packaging. New techniques boost performance, offering alternatives to conventional plastics.

Silva, Simão B. [REQUIMTE/LAQV, ISEP, Polytechnic ↗
DOE OSTI2022

Report on Evolution of Inconel 718 Following HFIR Irradiation

The report presents the microstructure and mechanical properties of 3D printed Inconel 718 after irradiation in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) to assess its potential use as a structural material. The structural components near the outlets of several proposed reactor cores will experience significant neutron fluxes and outlet coolant temperatures ranging from the hot standby temperature of 300 °C to nearly 550 °C at the center of the part. These components must support the core in appropriate loading conditions and require structural analysis at relevant temperatures. In FY21, three heat treatments were designed and conducted to simplify the microstructure and to determine how each precipitating phase contributed to the overall strength. In FY21, baseline mechanical properties were measured from uniaxial tensile tests on subsize SS-J2 specimens at room temperature and at elevated temperatures of 300, 450, and 600 °C to serve a comparison to the irradiated properties. Four capsules containing 3D printed Inconel 718 were inserted into HFIR in FY21 for a matrix of two temperatures and two doses. The lower of the two doses was available for characterization in FY22. Multiple heat treatments of Inconel 718 irradiated to nominal conditions of 2 displacements per atom (dpa) at either 300 or 600 °C were strained with uniaxial tensile tests at the Irradiated Material Examination and Testing (IMET) Facility to discern the mechanical properties. Transmission electron microscopy was performed to correlate the observed mechanical properties with nanoscale features. The initially homogenous AM718-HM increased in strength at both irradiation temperatures based on a high density of nanometer-scale radiation-induced cavities at lower temperature and nucleation and growth of γ" precipitates at higher temperatures. The precipitate-hardened AM718-HT2 showed very small differences in strength before and after irradiation: the contribution to strength from γ" precipitates was replaced with dislocation loops. Because the radioactivity of the nickel superalloys from neutron activation limited the scope of the analysis, a feasibility study examined the possibility of an ultra-miniature specimen geometry, colloquially SS-Tiny (SS-T), for mechanical property determination using the nonirradiated Inconel 718. This study found an overestimation of ductility from the SS-T geometry with yield strength and ultimate tensile strength slightly above the SS-J2 geometry: this could be contributed to a reduction in specimen thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The influence of thermomechanical treatment pathways on texture and mechanical properties in ARB Cu/Nb nanolaminates

Accumulative roll-bonded Cu/Nb nanolaminates (ARB Cu/Nb) possess high strength, thermal stability, and radiation tolerance arising from a high content of heterophase interfaces at fine layer thicknesses. These properties can be tailored by processing parameters used in the ARB Cu/Nb fabrication process, in which layer thickness, thermal history, and strain pathway determine the interface types and resultant properties found in the material. In this work, we subject ARB Cu/Nb to annealing, and then two different rolling pathways – one where rolling direction is held constant (longitudinal rolling, or LR), and one where rolling direction is rotated by 90º and held constant thereafter (cross rolling, or CR). Rolling is performed on ARB Cu/Nb over a targeted range of layer thicknesses from 193 to 25 nm and resultant bulk textures measured by neutron diffraction are correlated with mechanical properties measured by miniaturized tensile tests. The annealing procedure sharpens texture in both phases. We find that Cu mostly develops the same texture in LR and CR. In contrast, Nb develops a distinct texture along the CR pathway that is distinct from the LR texture. The composite texture of Cu/Nb is thus distinct between LR and CR pathways. This difference in texture development between Cu and Nb as a function of strain after change in rolling direction demonstrates the viability for deliberate pairing of Cu LR and Nb CR textures at a desired layer thickness. For mechanical properties, we find that differences in texture do not result in yield or flow stress differences above a layer thickness of 25 nm. Below a layer thickness of 25 nm, despite similar Taylor factors, yield and flow stress and are significantly different. In conclusion, this indicates texture only influences mechanical behavior at low layer thickness, where interface structure dominates mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets

Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Near-Net-Shape HIP Manufacturing for sCO2 Turbomachinery Cost Reduction

sCO2 turbomachinery that operates above 650°C requires the use of γ' strengthened Ni-based superalloys, leading to high cost and barrier of market adoption. Near-net-shape (NNS) HIP manufacturing with 282® alloy powder is being developed for sCO2 turbine components, with a significant estimated cost reduction. Tensile, creep, low cycle fatigue properties of argon gas atomized and plasma atomized powders were evaluated and compared to sand cast HAYNES® 282®. While tensile strength and fatigue life outperformed sand cast material, a 10~25% debit in the creep stress capability was observed due to the fine grain size and presence of prior particle boundaries (PPBs). Finite element model calibrated by powder rheological properties accurately predicted the nonuniform shrinkage during HIP, providing HIP tooling design to achieve the target dimension. A 20 lbs. turbine nozzle ring was successfully demonstrated within 0.01 inch dimensional tolerance at the vanes. A 1700lbs. turbine casing with complex internal struts and manifolds was also demonstrated being close to the target dimension.

14 SOLAR ENERGY↗
DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Application of lipid-stabilized liquid-liquid interfaces in 3D printing of biomaterials

Developing strategies to stabilize liquid-liquid interfaces is essential for advancing applications in various biomedical systems. This study introduces a novel biocompatible in situ-forming material in which lipid self-assembly stabilizes water–oil interfaces, enabling controlled structuring of liquids through liquid-in-liquid 3D printing. The stabilization process, driven by the formation of nanostructures at the interface, is thoroughly analyzed through small-angle X-ray scattering (SAXS), rheometry, and microscopy techniques. This material system enables the fabrication of complex 3D constructs, including fibers, substrates, and microneedle patches, which exhibit outstanding mechanical properties and biocompatibility, as confirmed by tensile testing and cell viability tests. Here, by leveraging the unique properties of lipid-stabilized interfaces, this work demonstrates the potential of this approach for diverse biomedical applications such as drug delivery and tissue engineering while establishing a foundation for future advancements in liquid-in-liquid 3D printing technology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Tensile and compressive creep properties of a quaternary Al-Cu-Mn-Zr (ACMZ) alloy and its commercial counterpart (Al-Cu-Mn-Zr with Ni, Co and Sb additions, RR350) are investigated at 300°C. At low stresses up to 30 MPa where diffusional creep dominates, creep resistance is the same in tension and compression and RR350 deforms more slowly than ACMZ, consistent with RR350 alloy's larger linear fraction of intergranular precipitates (Al7Cu2(NiFe) and Al9FeNi for RR350 vs. θ-Al2Cu for ACMZ) and a reduced fraction of precipitate-free zones near grain boundaries. At stresses between 30 and 80 MPa, dislocation creep with a stress exponent n ~ 3 becomes rate-limiting in compression, which is expected to be controlled by θ' precipitates within the grain bulk. By contrast, in tension, enhanced creep rate and higher apparent stress exponents are measured, consistent with cavitation at intergranular precipitates becoming increasingly dominant as the stress increases. In the dislocation creep regime, RR350 alloy is again more creep resistant than ACMZ alloy, which is related to three mechanisms (i) a reduced fraction of softer precipitate-free zones, (ii) more effective load transfer to intergranular precipitates, and (iii) reduced cavitation. A model for cavitation is applied to calculate tensile creep rates from compressive creep rates and the model successfully predicts the improved tensile creep resistance of the RR350 alloy. Overall, the present investigation underscores the importance of intergranular grain boundary precipitates, in addition to strengthening θ' precipitates, in enhancing the creep resistance of Al-Cu alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A novel digital lifecycle for Material‐Process‐Microstructure‐Performance relationships of thermoplastic olefins foams manufactured via supercritical fluid assisted foam injection molding

Abstract This research significantly enhances the applicability of thermoplastic olefins (TPOs) in the automotive industry using supercritical N 2 as a physical foaming agent, effectively addressing the limitations of traditional chemical agents. It merges experimental results with simulations to establish detailed material‐process‐microstructure‐performance (MP2) relationships, targeting 5–20% weight reductions. This innovative approach labeled digital lifecycle (DLC) helps accurately predict tensile, flexural, and impact properties based on the foam microstructure, along with experimentally demonstrating improved paintability. The study combines process simulations with finite element models to develop a comprehensive digital model for accurately predicting mechanical properties. Our findings demonstrate a strong correlation between simulated and experimental data, with about a 5% error across various weight reduction targets, marking significant improvements over existing analytical models. This research highlights the efficacy of physical foaming agents in TPO enhancement and emphasizes the importance of integrating experimental and simulation methods to capture the underlying foaming mechanism to establish material‐process‐microstructure‐performance (MP2) relationships. Highlights Establishes a material‐process‐microstructure‐performance (MP2) for TPO foams Sustainably produces TPO foams using supercritical (ScF) N 2 with 20% lightweighting Shows enhanced paintability for TPO foam improved surface aesthetics Digital lifecycle (DLC) that predicts both foam microstructure and properties DLC maps process effects & microstructure onto FEA mesh for precise prediction

Engineering↗
DOE OSTI2024

Melt compounding of spray-dried cellulose nanofibrils/polypropylene and their application in 3D printing

Abstract Micro- and nano-scale cellulosic fillers exhibit excellent dispersion and distribution within a thermoplastic matrix during the process of melt compounding or injection molding. In this study, spray-dried cellulose nanofiber (SDCNF) powders were manufactured using a pilot-scale rotating disk atomizer spray dryer. Bleached Kraft pulp (BKP), unbleached Kraft pulp (UKP), and old corrugated cardboard pulp (OCC) fibrillated at a fines level of 90% were used as feedstock materials for spray-drying. BKP-, UKP-, and OCC- SDCNFs were compounded with polypropylene using a twin screw co-rotating extruder. Maleic anhydride grafted polypropylene (MAPP) was used as a coupling agent in the composite formulations. The tensile, flexural, and impact properties of SDCNF-filled PP composites increased at 10 wt% SDCNF loading. The presence of SDCNFs in the PP matrix resulted in faster crystallization and a 12% reduction in the degree of crystallinity of the neat PP. The coefficient of thermal expansion (CTE) of neat PP was reduced by up to 31% attributable to the presence of the SDCNFs. Application of the SDCNF-reinforced PP composites in 3D printing reduced the shrinkage rate of the printed neat PP by 39%, and the printability of the PP was significantly improved with the addition of the SDCNFs.

Materials Science↗
DOE OSTI2022

Effect of solution concentration on ethylene propylene diene monomer (EPDM) nonmetallic components used in caustic liquid waste transfer lines

The hose-in-hose transfer lines (HIHTL) used to transfer waste at the United States Department of Energy’s Hanford Site Tank Farm are fabricated from an ethylene propylene diene monomer (EPDM) synthetic rubber. During waste transport, these hoses are exposed to several stressors including caustic solutions at high temperatures and high pressures, as well as β and γ radiation. The aging behavior of HIHTL and dog-bone shaped EPDM specimens were evaluated by exposure to solutions at 77 °C containing 0.00, 6.25, 12.50, and 25.00 % (v/v) sodium hydroxide (NaOH) for 12-months. After the exposure, the material properties of the specimens were measured and compared to the unaged samples. The material properties evaluated included the tensile strength of the EPDM dog-bone samples and the burst pressure of the HIHTL. Both the tensile strength of the EPDM dog-bone samples and the burst pressure of the HIHTL specimens exposed to the 6.25 % NaOH solution exhibited the most significant deterioration and those exposed to 25.00 % NaOH solution had the least deterioration. Finally, examination of the HIHTL and the EPDM dog-bone specimens with scanning electron microscopy showed that the deterioration for the specimens exposed to 6.25 % NaOH solution were the most severe and the samples exposed to 25.00 % NaOH solution had the least deterioration.

42 ENGINEERING↗