Search NASA⌕ Search

SEARCH · Search NASA

Results for “THEORIES - FLOW, SUPERSONIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Transonic flutter study of a 50.5 deg cropped-delta wing with two rearward-mounted nacelles

Transonic flutter characteristics of three geometrically similar delta-wing models were experimentally determined in the Langley transonic dynamics tunnel at Mach numbers from about 0.6 to 1.2. The models were designed to be simplified versions of an early supersonic transport wing design. The model was an aspect-ratio-1.28 cropped-delta wing with a leadingedge sweep of 50.5 deg. The flutter characteristics obtained for this wing configuration indicated a minimum flutter-speed index near a Mach number of 0.92 and a transonic compressibility dip amounting to about a 27-percent decrease in the flutter-speed index relative to the value at a Mach number of 0.6. Analytical studies were performed for one wing model at Mach numbers of 0.6, 0.7, 0.8, and 0.9 by using both doublet-lattice and lifting-surface (kernel-function) unsteady aerodynamic theory. A comparison of the analytical and experimental flutter results showed good agreement at all Mach numbers investigated.

Sandford, M. C.↗
NASA NTRS1952

Investigation in the Ames Supersonic Free-Flight Wind Tunnel of the Static Longitudinal Stability of the Hermes A-3B Missile at a Mach Number of 5.0

Models of the Hermes A-3B missile were tested in the Ames supersonic free-flight wind tunnel to determine the static-longitudinal-stability characteristics at a Mach number of 5.0 and a Reynolds number based on body length of 10 million. The results indicated that the model center of pressure was 45.3 percent of the body length aft of the nose and the lift-curve slope based on body frontal area was 0.064 per degree. Estimates indicated that the effect on these characteristics of aeroelastic twisting of the model fins was small but important if a precise location of center of pressure is required. A comparison of the test results with predictions based on available theory showed that the theory was useful only for rough estimates, The drag coefficient at zero lift, based on body frontal area, was found to be 0.155.

Denardo, Billy Pat↗
NASA NTRS1954

An Experimental Investigation of Reduction in Transonic Drag Rise at Zero Lift by the Addition of Volume to the Fuselage of a Wing-body-tail Configuration and a Comparison with Theory

An experimental investigation was made by the free-fall recoverable-model technique to assess at zero lift the possibilities of reducing the drag-rise coefficients of a wing-body-cruciform-tail combination by adding volume to the fuselage. The basic features of the test model were an unswept aspect-ratio-3.1 thin wing, a fineness-ratio-12.4 fuselage, and four 45 degrees sweptback tail surfaces. The tests covered a Mach number range of 0.84 to 1.15 with Reynolds numbers of 6.000.000 to 14,000,000, based on the wing mean aerodynamic chord. Considerable reduction in drag-rise coefficient was effected for several different modifications by the addition of properly distributed volume to the fuselage. In one instance, a reduction in drag coefficient was obtained by adding a volume which was almost four times the exposed wing volume. The computation method presented in NACA RM A53H17 generally predicted the supersonic drag-rise coefficients for each modification within 20 percent of the experimental values. As in the above-mentioned report, the predictions at a Mach number of one were not accurate. The changes in drag-rise coefficients resulting from the modifications were generally predicted with better accuracy than the values of drag-rise coefficients.

Holdaway, George H↗
NASA NTRS1960

Ground Measurements of Airplane Shock-Wave Noise at Mach Numbers to 2.0 and at Altitudes to 60,000 Feet

The intensity of shock-wave noise at the ground resulting from flights at Mach numbers to 2.0 and altitudes to 60,000 feet was measured. Meagurements near the ground track for flights of a supersonic fighter and one flight of a supersonic bomber are presented. Level cruising flight at an altitude of 60,000 feet and a Mach number of 2.0 produced sonic booms which were considered to be tolerable, and it is reasonable t o expect that cruising flight at higher altitudes will produce booms of tolerable intensity for airplanes of the size and weight of the test airplanes. The measured variation of sonic-boom intensity with altitude was in good agreement with the variation calculated by an equation given in NASA Technical Note D-48. The effect of Mach number on the ground overpressure is small between Mach numbers of 1.4 and 2.0, a result in agreement with the theory. No amplification of the shock-wave overpressures due to refraction effects was apparent near the cutoff Mach number. A method for estimating the effect of fligh-path angle on cutoff Mach number is shown. Experimental results indicate agreement with the method, since a climb maneuver produced booms of a much decreased intensity as compared with the intensity of those measured in level flight at about the same altitude and Mach number. Comparison of sound pressure levels for the fighter and bomber airp lanes indicated little effect of either airplane size or weight at an altitude of 40,000 feet.

Lina, Lindsay J.↗
NASA NTRS2014

The Application of LENR to Synergistic Mission Capabilities

This paper presents an overview of several missions that exploit the capabilities of a Low Energy Nuclear Reaction (LENR) aircraft propulsion system. LENR is a form of nuclear energy and potentially has over 4,000 times the energy density of chemical energy sources. It does not have any harmful emissions or radiation which makes it extremely appealing. The global reliance on crude oil for aircraft energy creates the opportunity for a revolutionary change with LENR. LENR will impact aircraft performance capabilities, military capabilities, the environment, the economy, and society. Although there is a lot of interest in LENR, there is no proven theory that explains it. Some of the technical challenges are thermal runaway and start-up time. This paper does not explore the feasibility of LENR and assumes that a system is available. A non-dimensional aircraft mass (NAM) ratio diagram is used to explore the aircraft system design space. The NAM ratio diagram shows that LENR can enable long range and high speed missions. The design space exploration led to the conclusion that LENR aircraft would be well suited for high altitude long endurance (HALE) missions, including communications relay and scientific missions for hurricane tracking and other weather phenomena, military intelligence, surveillance, and reconnaissance (ISR) and airspace denial missions, supersonic passenger transport aircraft, and international cargo transport. This paper describes six of those missions.

Wells, Douglas P.↗
NASA NTRS1978

Photochemistry and dynamics of the ozone layer

The paper presents a broad review of the photochemical and dynamic theories of the ozone layer. The two theories are combined into the MIT three-dimensional dynamic-chemical quasi-geostrophic model with 26 levels in the vertical spaced in logarithmic pressure coordinates between the ground and 72-km altitude. The chemical scheme incorporates the important odd nitrogen, odd hydrogen, and odd oxygen chemistry, but is simplified in the sense that it requires specification of the distributions of NO2, OH and HO2. The prognostic equations are the vorticity equation, the perturbation thermodynamic equation, and the global mean and perturbation continuity equations for ozone; diagnostic equations include the hydrostatic equation, the balance condition, and the mass continuity equation. The model is applied to the investigation of the impact of supersonic aircraft on the ozone layer.

Prinn, R. G.↗
NASA NTRS1974

Flutter of panels on discrete flexible supports

The supersonic flutter of wide panels on discrete flexible supports is investigated for three different panel-support configurations. The first study examines the effect of support stiffness on the flutter behavior of a specific five-support configuration with leading-and trailing-edge overhangs; this configuration was recently under consideration for a heat shield on an entry body. The second study investigates the effect of support stiffness on flutter of panels with various numbers of equally spaced supports. The third study examines the effect of center-support location on the flutter of panels with three supports. Results are presented in nondimensional form. The analysis is based on wide-plate structural theory and Ackeret aerodynamics. Finite differences are employed to obtain solutions for flutter pressure. A computer program based on this analysis and including a direct solution technique is presented. The program can be used to find the flutter pressure of wide panels of variable thickness supported by any number of flexible supports.

Stein, M.↗
NASA NTRS1974

Exploratory tests of two strut fuel injectors for supersonic combustion

Results of supersonic mixing and combustion tests performed with two simple strut injector configurations, one with parallel injectors and one with perpendicular injectors, are presented and analyzed. Good agreement is obtained between static pressure measured on the duct wall downstream of the strut injectors and distributions obtained from one-dimensional calculations. Measured duct heat load agrees with results of the one-dimensional calculations for moderate amounts of reaction, but is underestimated when large separated regions occur near the injection location. For the parallel injection strut, good agreement is obtained between the shape of the injected fuel distribution inferred from gas sample measurements at the duct exit and the distribution calculated with a multiple-jet mixing theory. The overall fraction of injected fuel reacted in the multiple-jet calculation closely matches the amount of fuel reaction necessary to match static pressure with the one-dimensional calculation. Gas sample measurements with the perpendicular injection strut also give results consistent with the amount of fuel reaction in the one-dimensional calculation.

Anderson, G. Y.↗
NASA NTRS2011

A Laboratory and Theoretical Study of Silicon Hydroxide SiOH

The rotational spectrum of the triatomic free radical SiOH in its X 2A' ground electronic state has been observed in a supersonic molecular beam by Fourier transform microwave spectroscopy. The fundamental (10,1 yields 00,0) transition has been detected for normal SiOH and for three rare isotopic species: (30)SiOH, Si(18)OH, and SiOD. The same transition has also been observed in two of three excited vibrational states, v2 and v3, for the most abundant species. Precise spectroscopic constants, including those that describe the effective spin doubling and hydrogen hyperfine structure, have been derived for each isotopic species or vibrational state. To complement the laboratory work, theoretical calculations of the structure, dipole moment, and energies of the X 2A' and low-lying 1 2A'' states have also been undertaken at the coupled cluster level of theory. In agreement with theoretical predictions, we conclude from the hyperfine constants that SiOH is a best described as a pi-type radical, with the unpaired electron localized on a p orbital on the silicon atom. Assuming a bond angle of 118.5 deg, the Si-O bond length is 1.647(2) Angstroms and the O-H bond length is 0.969(4) Angstrom.

McCarthy, M. C.↗
NASA NTRS2000

Discharge Coefficients for Axisymmetric Supersonic Nozzles

Computational Fluid Dynamics (CFD) analysis was used to compute effective nozzle discharge coefficients for subscale sharp-edged converging/diverging nozzles, with a variety of convergence half-angles, motor operating conditions, and two propellants with different ballistics. Convergence half-angles ranged from 0 to 80 deg. Analysis was conducted at total temperatures from 2946K (5303R) to 3346K (6023R) and over total pressures ranged from 2.72 MPa (395 psia) to 20.68 MPa (3000 psia). Area ratios (A(sub e)/A*) ranged from 7.43 to 9.39. Ratio of specific heats (gamma) ranged from 1.13 to 1.18. Throat and exit Reynolds numbers were calculated to be 8.26 x 10(exp 5) and 5.51 x 10(exp 5), respectively. Present results of nozzle discharge coefficients are reported and correlated as a function of nozzle convergence half-angle (theta(sub c)) and area ratios (A(sub e)/A*) for a constant divergence half-angle (theta(sub d)) of 15 deg. Computed discharge coefficients ranged from 0.88 to 0.97. They are compared with theory and experimental data available in literature. Available turbulence models with respect to grid refinements and heat transfer are discussed.

Ahmad, Rashid A.↗
NASA NTRS1980

Design of a multivariable integrated control for a supersonic propulsion system

An inlet/engine/nozzle integrated control mode for the propulsion system of an advanced supersonic commercial aircraft was studied. Results show that integration of these control functions can result in both operational and performance benefits for the propulsion system. For example, this integrated control mode may make it possible to minimize the use of inlet bypass doors for shock position control. This may be of benefit to the aircraft as a result of minimizing: (1) bypass bleed drag effects; (2) perturbations to the aircraft resulting from the side thrust effect of the bypass bleeds; and (3) potential unstarts of the inlet. A conceptual integrated control mode was developed which makes use of many cross coupling paths between inlet and engine control variables and inlet and engine sensed variables. A multivariable control design technique based upon linear quadratic regulator theory was applied to designing the feedback gains for this control to allow a simulation evaluation of the benefits of the integrated control mode.

Beattie, E. C.↗
NASA NTRS2003

An Analysis of Measured Pressure Signatures From Two Theory-Validation Low-Boom Models

Two wing/fuselage/nacelle/fin concepts were designed to check the validity and the applicability of sonic-boom minimization theory, sonic-boom analysis methods, and low-boom design methodology in use at the end of the 1980is. Models of these concepts were built, and the pressure signatures they generated were measured in the wind-tunnel. The results of these measurements lead to three conclusions: (1) the existing methods could adequately predict sonic-boom characteristics of wing/fuselage/fin(s) configurations if the equivalent area distributions of each component were smooth and continuous; (2) these methods needed revision so the engine-nacelle volume and the nacelle-wing interference lift disturbances could be accurately predicted; and (3) current nacelle-configuration integration methods had to be updated. With these changes in place, the existing sonic-boom analysis and minimization methods could be effectively applied to supersonic-cruise concepts for acceptable/tolerable sonic-boom overpressures during cruise.

Mack, Robert J.↗
NASA NTRS1993

Flutter analysis using transversality theory

A new method of calculating flutter boundaries of undamped aeronautical structures is presented. The method is an application of the weak transversality theorem used in catastrophe theory. In the first instance, the flutter problem is cast in matrix form using a frequency domain method, leading to an eigenvalue matrix. The characteristic polynomial resulting from this matrix usually has a smooth dependence on the system's parameters. As these parameters change with operating conditions, certain critical values are reached at which flutter sets in. Our approach is to use the transversality theorem in locating such flutter boundaries using this criterion: at a flutter boundary, the characteristic polynomial does not intersect the axis of the abscissa transversally. Formulas for computing the flutter boundaries and flutter frequencies of structures with two degrees of freedom are presented, and extension to multi-degree of freedom systems is indicated. The formulas have obvious applications in, for instance, problems of panel flutter at supersonic Mach numbers.

Afolabi, D.↗
NASA NTRS2003

Aeroelastic System Development Using Proper Orthogonal Decomposition and Volterra Theory

This research combines Volterra theory and proper orthogonal decomposition (POD) into a hybrid methodology for reduced-order modeling of aeroelastic systems. The out-come of the method is a set of linear ordinary differential equations (ODEs) describing the modal amplitudes associated with both the structural modes and the POD basis functions for the uid. For this research, the structural modes are sine waves of varying frequency, and the Volterra-POD approach is applied to the fluid dynamics equations. The structural modes are treated as forcing terms which are impulsed as part of the uid model realization. Using this approach, structural and uid operators are coupled into a single aeroelastic operator. This coupling converts a free boundary uid problem into an initial value problem, while preserving the parameter (or parameters) of interest for sensitivity analysis. The approach is applied to an elastic panel in supersonic cross ow. The hybrid Volterra-POD approach provides a low-order uid model in state-space form. The linear uid model is tightly coupled with a nonlinear panel model using an implicit integration scheme. The resulting aeroelastic model provides correct limit-cycle oscillation prediction over a wide range of panel dynamic pressure values. Time integration of the reduced-order aeroelastic model is four orders of magnitude faster than the high-order solution procedure developed for this research using traditional uid and structural solvers.

Lucia, David J.↗
NASA NTRS1953

Investigation at supersonic speeds of the variation with Reynolds number and Mach number of the total, base, and skin-friction drag of seven boattail bodies of revolution designed for minimum wave drag

An investigation has been conducted in the Langley 9-inch supersonic tunnel to determine the effect of the variation with Reynolds number and Mach number of the total, base, and skin-friction drag at zero lift of seven boattail bodies of revolution designed for minimum wave drag according to NACA TN 2550. The tests covered a Reynolds number range from approximately 1.0 x 10(6) to 10.0 x 10(6) at Mach numbers of 1.62, 1.93, and 2.41, respectively. The results show that base drag and, in general, the total drag increase with increasing values of the ratio of base area to maximum area B/S(sub max), although the results reported in NACA TN 3054 showed that the wave drag decreased with increasing values of B/S(sub max). The laminar skin-friction drag is in agreement with the theoretical predictions used, and, within the Mach number range of these tests, the simple Blasius incompressible theory gives a satisfactory prediction. Except for values of B/S (sub max) near 1, the Reynolds number of transition increases with increasing Mach number and as this ratio approaches 1 this variation is seen to reverse. These variations in Reynolds number of transition with Mach number appear to be associated with the changes in pressure gradient over the rear of the bodies.

Bromm, August F , Jr↗
NASA NTRS1959

A Numerical Method for Calculating the Wave Drag of a Configuration from the Second Derivative of the Area Distribution of a Series of Equivalent Bodies of Revolution

A method based on linearized and slender-body theories, which is easily adapted to electronic-machine computing equipment, is developed for calculating the zero-lift wave drag of single- and multiple-component configurations from a knowledge of the second derivative of the area distribution of a series of equivalent bodies of revolution. The accuracy and computational time required of the method to calculate zero-lift wave drag is evaluated relative to another numerical method which employs the Tchebichef form of harmonic analysis of the area distribution of a series of equivalent bodies of revolution. The results of the evaluation indicate that the total zero-lift wave drag of a multiple-component configuration can generally be calculated most accurately as the sum of the zero-lift wave drag of each component alone plus the zero-lift interference wave drag between all pairs of components. The accuracy and computational time required of both methods to calculate total zero-lift wave drag at supersonic Mach numbers is comparable for airplane-type configurations. For systems of bodies of revolution both methods yield similar results with comparable accuracy; however, the present method only requires up to 60 percent of the computing time required of the harmonic-analysis method for two bodies of revolution and less time for a larger number of bodies.

Levy, Lionel L., Jr.↗
NASA NTRS1984

An experimental investigation of the effect of boundary layer refraction on the noise from a high-speed propeller

Models of supersonic propellers were previously tested for acoustics in the Lewis 8- by 6-Foot Wind Tunnel using pressure transducers mounted in the tunnel ceiling. The boundary layer on the tunnel ceiling is believed to refract some of the propeller noise away from the measurement transducers. Measurements were made on a plate installed in the wind tunnel which had a thinner boundary layer than the ceiling boundary layer. The plate was installed in two locations for comparison with tunnel ceiling noise data and with fuselage data taken on the NASA Dryden Jetstar airplane. Analysis of the data indicates that the refraction increases with: increasing boundary layer thickness; increasing free stream Mach number; increasing frequency; and decreasing sound radiation angle (toward the inlet axis). At aft radiation angles greater than about 100 deg there was little or no refraction. Comparisons with the airplane data indicated that not only is the boundary layer thickness important but also the shape of the velocity profile. Comparisons with an existing two-dimensional theory, using an idealized shear layer to approximate the boundary layer, showed that the theory and data had the same trends. Analysis of the data taken in the tunnel at two different distances from the propeller indicates a decay with distance in the wind tunnel at high Mach numbers but the decay at low Mach numbers is not as clear.

Dittmar, J. H.↗
DOE OSTI2021

Photodissociation and Infrared Spectroscopy of Uranium–Nitrogen Cation Complexes

Laser vaporization of uranium in a pulsed supersonic expansion of nitrogen is used to produce complexes of the form U + (N 2 ) n (n = 1–8). These ions are mass selected in a reflectron time-of-flight spectrometer and studied with visible and UV laser fixed-frequency photodissociation and with tunable infrared laser photodissociation spectroscopy. The dissociation patterns and spectroscopy of U + (N 2 ) n indicate that N 2 ligands are intact molecules and that there is no insertion chemistry resulting in UN + or NUN + . Fixed frequency photodissociation at 532 and 355 nm indicate that the U + –N 2 bond dissociation energy varies little with changing coordination. The photon energy and the number of ligands eliminated allow an estimate of the average U + –N 2 dissociation energy of 12 kcal/mol. Infrared bands are observed for these complexes near the N–N stretch vibration via elimination of N 2 molecules. These resonances are observed to be shifted about 130 cm–1 to the red from the free-N 2 frequency for complexes with n = 3–8. Density functional theory indicates that U + is most stable in the sextet state in these complexes and that N 2 molecules bind in end-on configurations. Furthermore, the fully coordinated complex is predicted to be U + (N 2 ) 8 , which has a cubic structure. The vibrational frequencies predicted by theory are consistently lower than those in the experiment, independent of the isomeric structure or spin state of the complexes. Despite its failure to reproduce the infrared spectra, theory provides an average U + –N 2 dissociation energy of 11.8 ± 0.5 kcal/mol, in good agreement with the value from the experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗