SEARCH · Search NASA

Results for “Unitary Plan Wind Tunnel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗

NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗

NASA NTRS1985

Supersonic aerodynamic characteristics of canard, tailless, and aft-tail configurations for 2 wing planforms

Aerodynamic characteristics of canard, tailless, and aft tail configurations were compared in tests on a general research model (generic fuselage without canopy, inlets, or vertical tails) at Mach 1.60 and 2.00 in the Langley Unitary Plan Wind Tunnel. Two uncambered wing planforms (trapezoidal with 44 deg leading edge sweep and delta with 60 deg leading edge sweep) were tested for each configuration. The relative merits of the configurations were also determined theoretically, to evaluate the capabilities of a linear theory code for such analyses. The canard and aft tail configurations have similar measured values for lift curve slope, maximum lift drag ratio, and zero lift drag. The stability decrease as Mach number increases is greatest for the tailless configuration and least for the canard configuration. Because of very limited accuracy in predicting the aerodynamic parameter increments between configurations, the linear theory code is not adequate for determining the relative merits of canard, tailless, and aft tail configurations.

Covell, P. F.↗

NASA NTRS1985

Experimental and theoretical study of the longitudinal aerodynamic characteristics of delta and double-delta wings at Mach numbers of 1.60, 1.90, and 2.16

An experimental and theoretical study was conducted to investigate the supersonic aerodynamic characteristics of delta and double-delta wings. Testing was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. The double-delta wings exhibited lower zero-lift drag values than the delta wings having the same aspect ratio, whereas delta wings provided the lower drag due to lift. Deflections of the trailing-edge flaps for pitch control revealed that the induced aerodynamic forces were only a function of the flap planform and were independent of wing planform. The supporting theoretical analysis showed that the supersonic design and analysis system (SDAS) did not consistently predict all the longitudinal aerodynamic characteristics of the low-sweep, low-fineness-ratio wing-body configurations under investigation.

Wood, R. M.↗

NASA NTRS1986

Planform effects for low-fineness ratio multibody configurations at supersonic speeds

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration has been conducted in NASA Langley Research Center's Unitary Plan Wind Tunnel at Mach numbers 1.6, 1.8, 2.0, and 2.16. Experimental and theoretical values of lift, drag, and pitching moment were obtained on three configurations which varied in outboard panel planform only. The three variations were at 65 deg delta, a 70/66 deg cranked arrow, and a 20 deg trapezoidal planform . The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics and to evaluate the ability of two existing linearized-theory aerodynamic methods to predict these effects. Experimental data showed that the planforms produced the lift, drag-due-to-lift, and pitching-moment characteristics typically found on single-body configurations. However, the data also showed that planform has a minimal influence on zero-lift drag, which is not typical of single-body configurations. Theoretical aerodynamic analysis indicated that codes based on linearized theory adequately predicted the effect of planform on the supersonic aerodynamics.

Mcmillin, S. N.↗

NASA NTRS1984

Supersonic, nonlinear, attached-flow wing design for high lift with experimental validation

Results of the experimental validation are presented for the three dimensional cambered wing which was designed to achieve attached supercritical cross flow for lifting conditions typical of supersonic maneuver. The design point was a lift coefficient of 0.4 at Mach 1.62 and 12 deg angle of attack. Results from the nonlinear full potential method are presented to show the validity of the design process along with results from linear theory codes. Longitudinal force and moment data and static pressure data were obtained in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.58, 1.62, 1.66, 1.70, and 2.00 over an angle of attack range of 0 to 14 deg at a Reynolds number of 2.0 x 10 to the 6th power per foot. Oil flow photographs of the upper surface were obtained at M = 1.62 for alpha approx. = 8, 10, 12, and 14 deg.

Pittman, J. L.↗

NASA NTRS1987

Investigation of leading-edge flap performance on delta and double-delta wings at supersonic speeds

An investigation of the aerodynamic performance of leading-edge flaps on three clipped delta and three clipped double-delta wing planforms with aspect ratios of 1.75, 2.11, and 2.50 was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. A primary set of fullspan leading-edge flaps with similar root and tip chords were investigated on each wing, and several alternate flap planforms were investigated on the aspect-ratio-1.75 wings. All leading-edge flap geometries were effective in reducing the drag at lifting conditions over the range of wing aspect ratios and Mach numbers tested. Application of a primary flap resulted in better flap performance with the double-delta planform than with the delta planform. The primary flap geometry generally yielded better performance than the alternate flap geometries tested. Trim drag due to flap-induced pitching moments was found to reduce the leading-edge flap performance more for the delta planform than for the double-delta planform. Flow-visualization techniques showed that leading-edge flap deflection reduces crossflow shock-induced separation effects. Finally, it was found that modified linear theory consistently predicts only the effects of leading-edge flap deflection as related to pitching moment and lift trends.

Covell, Peter F.↗

NASA NTRS1987

Drag measurements of blunt stores tangentially mounted on a flat plate at supersonic speeds

An investigation has been conducted in the Langley Unitary Plan Wind Tunnel to measure the drag of blunt stores (hemispherical noses and afterbodies) tangentially mounted in various arrays on a flat plate at nominal Mach numbers of 1.60, 1.90, 2.16,and 2.86 and at a nominal Reynolds number of 2X10 to the 6th power per foot. The arrays consisted of two and three stores mounted in lateral, tandem, or staggered arrangements. The relative position of the stores in the arrays was varied while the drag of only one store was measured to determine the effect of spacing on the store drag. Store-on-store interference was determined by comparing the drag of a single store with the drag of the store in an array. The results indicate virtually all arrangements and spacings which were tested had favorable store-on-store interference (drag reduction) across the Mach number range. Tabulated data, schlieren photographs, and shadowgraphs are included.

Wilcox, Floyd J., Jr.↗

NASA NTRS1987

Computational and experimental investigation of cavity flowfields

This paper presents a computational and experimental investigation of supersonic flow past a cavity in a flat plate. The source of the particular interest in this problem is the ongoing study of the aerodynamic interference effects between a separating store and its bay in the parent body. An upwind relaxation scheme, utilizing flux vector splitting and line-Gauss-Seidel iterations, is used to solve Reynolds-averaged Navier-Stokes equations. Spatial discretizations of this two-dimensional analysis are based on implicit and finite-volume methods. Turbulence is modeled and shocks are captured. The flowfield of the symmetry plane at the half-width is computationally visualized and all flow properties are computed. Experimental tests are conducted in the Langley Unitary Plan Wind Tunnel to measure wall pressures and to capture schlieren photographs. Qualitative as well as quantitative data of computations and experiments agree very well. These two vehicles of investigation are merged to show open, closed and transitional cavity flow behaviors.

Baysal, O.↗

NASA NTRS1987

Investigation of the vortex flap concept on a 75-deg sweep delta wing at supersonic speeds

An experimental investigation of the aerodynamic performance of vortex flaps on a 75-deg sweep delta wing has been conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 1.7 to 2.8. The sharp leading edge vortex flaps consisted of the outboard 30 percent of the local wing semispan. Flap deflections of 0, 5, 10, and 15 deg were investigated, for both a wing-alone and a wing-body configuration. The flaps were effective in reducing the drag across the lift-coefficient range. Integration of the upper surface pressure distributions showed that the suction pressures induced by the vortex on the flap were responsible for the drag reductions. At some lift conditions, the minimum drag condition permitted hinge line separation or vortex migration inboard of the hinge line. This result is in contrast to subsonic results, where optimum conditions call for no hinge line separation. The magnitude of the drag reduction due to flap deflection generally decreased as Mach number increased. The effect of a cylindrical forebody on the drag reduction due to flap deflection was minimal.

Covell, Peter F.↗

NASA NTRS1988

Experimental and theoretical study of the effects of wing geometry on a supersonic multibody configuration

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration was conducted in NASA-Langley Research Center's Unitary Plan Wind Tunnel at Mach number of 1.6, 1.8, 2.0 and 2.16. Experimental and theoretical values of lift, drag, and pitching moment as well as surface pressures were obtained on several configurations which varied in both outboard-wing panel and inboard-wing panel planforms. The three outboard-wing panels were a 65 -deg delta and two trapezoidal wing planforms. An unswept and a 60-deg swept inboard-wing panels were also tested. The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics. The large trapezoidal wing provided increased performance over the small trapezoidal wing primarily due to a reduction in the zero-lift drag coefficient. The swept inboard-wing panel planforms provided a slightly higher L/D than the unswept inboard-wing panel due to a minimal improvement in zero-lift drag. Linear-theory aerodynamic codes were used to analyze the effect of planform on the supersonic aerodynamics and were found to generally produce adequate results.

Bauer, Steven X. S.↗

NASA NTRS1989

Effect of milling machine roughness and wing dihedral on the supersonic aerodynamic characteristics of a highly swept wing

An experimental investigation was conducted to assess the effect of surface finish on the longitudinal and lateral aerodynamic characteristics of a highly-swept wing at supersonic speeds. A study of the effects of wing dihedral was also made. Included in the tests were four wing models: three models having 22.5 degrees of outboard dihedral, identical except for surface finish, and a zero-dihedral, smooth model of the same planform for reference. Of the three dihedral models, two were taken directly from the milling machine without smoothing: one having a maximum scallop height of 0.002 inches and the other a maximum scallop height of 0.005 inches. The third dihedral model was handfinished to a smooth surface. Tests were conducted in Test Section 1 of the Unitary Plan Wind Tunnel at NASA-Langley over a range of Mach numbers from 1.8 to 2.8, a range of angle of attack from -5 to 8 degrees, and at a Reynolds numbers per foot of 2 x 10(6). Selected data were also taken at a Reynolds number per foot of 6 x 10(6). Drag coefficient increases, with corresponding lift-drag ratio decreases were the primary aerodynamic effects attributed to increased surface roughness due to milling machine grooves. These drag and lift-drag ratio increments due to roughness increased as Reynolds number increased.

Darden, Christine M.↗

NASA NTRS1989

Supersonic aerodynamic characteristics of a proposed Assured Crew Return Capability (ACRC) lifting-body configuration

An investigation was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers from 1.6 to 4.5. The model had a low-aspect-ratio body with a flat undersurface. A center fin and two outboard fins were mounted on the aft portion of the upper body. The outboard fins were rolled outboard 40 deg from the vertical. Elevon surfaces made up the trailing edges of the outboard fins, and body flaps were located on the upper and lower aft fuselage. The center fin pivoted about its midchord for yaw control. The model was longitudinally stable about the design center-of-gravity position at 54 percent of the body length. The configuration with undeflected longitudinal controls trimmed near 0 deg angle of attack at Mach numbers from 1.6 to 3.0 where lift and lift-drag ratio were negative. Longitudinal trim was near the maximum lift-drag ratio (1.4) at Mach 4.5. The model was directionally stable over Mach number range except at angles of attack around 4 deg at M = 2.5. Pitch control deflection of more than -10 deg with either elevons or body flaps is needed to trim the model to angles of attack at which lift becomes positive. With increased control deflection, the lifting-body configuration should perform the assured crew return mission through the supersonic speed range.

Ware, George M.↗

NASA NTRS1989

A transition detection study at Mach 1.5, 2.0, and 2.5 using a micro-thin hot-film system

A boundary-layer transition detection study was conducted in the NASA Langley unitary plan wind tunnel with an array of microthin hot films on a flat plate at Mach numbers 1.5, 2.0, and 2.5 and Reynolds numbers (1.0-4.5) x 10 to the 6th/ft. Transition locations were obtained online from the variation of normalized rms voltages from an array of hot-film sensors for both natural transition and a grit-induced wedge of turbulence. The effects of Mach number and Reynolds number on the location and length of the transition region for the two types of transition are presented from the online data. Also shown are the unit Reynolds number effects on transition Reynolds number, voltage-versus-time traces, spectra, and the data-acquisition system.

Johnson, Charles B.↗

NASA NTRS1991

Hypersonic waverider analysis - A comparison of numerical and experimental results

In this study two waverider configurations are analyzed numerically and experimentally. The geometries are designed using an inverse design and optimization code with the optimization procedure driven by maximized L/D and limited by geometric constraints. Euler and Navier-Stokes numerical simulations are performed with a partially flux-split finite-difference code developed at NASA Ames, F3D. Experimental data is obtained at NASA Langley in the Unitary Plan Wind Tunnel (UPWT) and the 20-Inch Mach 6 wind tunnel for flow visualization, force/moment, and surface pressure measurements at both on- and off-design conditions. Euler simulations are compared with analytic results obtained from conical flow theory, and Navier-Stokes simulations are compared with experimental results both qualitatively and quantitatively for on- and off-design conditions.

Jones, K. D.↗

NASA NTRS1992

Longitudinal and lateral-directional aerodynamic characteristics of a wing-cone configuration at Mach numbers from 2.5 to 4.5

A study was conducted to determine the longitudinal and lateral-directional aerodynamic characteristics of a generic wing-cone configuration at supersonic speeds. The fuselage has a 5 deg half-angle cone forebody, cylindrical midbody, and a 9 deg truncated cone afterbody. The delta wing (aspect ratio 1.0) had a 4 pct. thick diamond airfoil section. The tests were made in the Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 and 4.50. Angle of attack was varied from -4 to 28 degs, and angle of sideslip varied from -8 to 8 degs. Several configurations were studied to determine the effects of variations in wing longitudinal position, wing incidence, vertical tail configuration, canard shape, and nose bluntness. Typical effects of Reynolds number and Mach number on the longitudinal characteristics were observed. The incremental effects of the configuration variables were generally unaffected by Mach number. The directional stability characteristics of the large and small centerline mounted vertical tail configurations were significantly degraded with increasing angle of attack and Mach number.

Covell, Peter F.↗

NASA NTRS1992

Effect of planform and body on supersonic aerodynamics of multibody configurations

An experimental and theoretical investigation of the effect of the wing planform and bodies on the supersonic aerodynamics of a low-fineness-ratio, multibody configuration has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Force and moment data, flow-visualization data, and surface-pressure data were obtained on eight low-fineness-ratio, twin-body configurations. These configurations varied in inboard wing planform shape, outboard wing planform shape, outboard wing planform size, and presence of the bodies. The force and moment data showed that increasing the ratio of outboard wing area to total wing area or increasing the leading-edge sweep of the inboard wing influenced the aerodynamic characteristics. The flow-visualization data showed a complex flow-field system of shocks, shock-induced separation, and body vortex systems occurring between the side bodies. This flow field was substantially affected by the inboard wing planform shape but minimally affected by the outboard wing planform shape. The flow-visualization and surface-pressure data showed that flow over the outboard wing developed as expected with changes in angle of attack and Mach number and was affected by the leading-edge sweep of the inboard wing and the presence of the bodies. Evaluation of the linear-theory prediction methods revealed their general inability to consistently predict the characteristics of these multibody configurations.

Mcmillin, S. Naomi↗

NASA NTRS1993

Supersonic aeroelastic instability results for a NASP-like wing model

An experimental study and an analytical study have been conducted to examine static divergence for hypersonic-vehicle wing models at supersonic conditions. A supersonic test in the Langley Unitary Plan Wind Tunnel facility was conducted for two wind-tunnel models. These models were nearly identical with the exception of airfoil shape. One model had a four-percent maximum thickness airfoil and the other model had an eight-percent maximum thickness airfoil. The wing models had low-aspect ratios and highly swept leading edges. The all-movable wing models were supported by a single-pivot mechanism along the wing root. For both of the wind-tunnel models, configuration changes could be made in the wing-pivot location along the wing root and in the wing-pivot pitch stiffness. Three divergence conditions were measured for the four-percent thick airfoil model in the Mach number range of 2.6 to 3.6 and one divergence condition was measured for the eight-percent thick airfoil model at a Mach number of 2.9. Analytical divergence calculations were made for comparison with experimental results and to evaluate the parametric effects of wing-pivot stiffness, wing-pivot location, and airfoil thickness variations. These analyses showed that decreasing airfoil thickness, moving the wing-pivot location upstream, or increasing the pitch-pivot stiffness have the beneficial effect of increasing the divergence dynamic pressures. The calculations predicted the trend of experimental divergence dynamic pressure with Mach number accurately; however, the calculations were approximately 25 percent conservative with respect to dynamic pressure.

Cole, Stanley R.↗