Search NASA⌕ Search

SEARCH · Search NASA

Results for “V/STOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Low speed wind tunnel test of ground proximity and deck edge effects on a lift cruise fan V/STOL configuration, volume 1

The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.

Stewart, V. R.↗
NASA NTRS1979

Recent applications of theoretical analysis to V/STOL inlet design

The theoretical analysis methods, potential flow, and boundary layer, used at Lewis are described. Recent application to Navy V/STOL aircraft, both fixed and tilt nacelle configurations, are presented. A three dimensional inlet analysis computer program is described and preliminary results presented. An approach to optimum design of inlets for high angle of attack operations is dicussed.

Stockman, N. O.↗
NASA NTRS1979

Critical considerations for wind-tunnel testing V/STOL aircraft models

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. The paper examines factors which must be dealt with to assure that the information obtained in experiments is accurate and representative of the full-scale aircraft modeled. Areas of discussion include: (1) Proper engine simulation selection and model size constraints as a result of the selection; (2) selection of reference power-off condition for determining propulsion interaction effects; (3) modeling of realistic flight conditions to obtain a comprehensive evaluation of the entire transition performance; and (4) wind-tunnel boundary interferences and how these are highly configuration dependent.

Margason, R. J.↗
NASA NTRS1979

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles-of attack (up to 120 deg). In general, diffuser blowing had a beneficial affect on all performance parameters. The angle-of-attack range for a separation-free flow substantially increased, and the fan face distortion reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.↗
NASA NTRS1979

The characteristics of a lift cruise fan V/STOL configuration in near proximity to a small deck with finite edge positions

Two V/STOL model configurations utilizing lift-cruise-fans for the propulsion system have been tested in the presence of a small landing platform with finite deck edge positions. Results and analysis of these tests are presented. The model was tested at both static (zero velocity) and forward speed conditions with several heights and deck edge positions. Configurations utilizing three fans and four fans were investigated. Incremental forces and moments induced by the various deck edge positions are analyzed as relating to the model height above the ground and the thrust velocity relationships. The test and analysis show the induced forces to be relatively unaffected by deck edge.

Stewart, V. R.↗
NASA NTRS1979

Recent applications of theoretical analysis to V/STOL inlet design

A brief description of the axisymmetric potential flow and boundary layer analysis methods used at the NASA Lewis Research Center, is presented. Application of this method to inlet problems arising from both tilt-nacelle and fixed-nacelle V/STOL aircraft configurations is illustrated. A three-dimensional inlet analysis computer program is described and the preliminary results presented. Finally, a suggested approach to optimum design of inlets for high angle-of-attack operation is discussed.

Stockman, N. O.↗
NASA NTRS1979

Force and moment data from a wind-tunnel test of a tilt-nacelle V/STOL propulsion system with an attitude control vane

A large scale, tilt nacelle V/STOL propulsion system, with an attitude control vane assembly mounted in the exhaust, was tested. The effectiveness of the control vane as well as the aerodynamic characteristics of the entire propulsion system were determined. The results, in the form of tabulated coefficients, for both the vane forces and moments and the total forces and moments produced by the propulsion system are presented.

Betzina, M. D.↗
NASA NTRS1979

Investigation of ground effects on large and small scale models of a three fan V/STOL aircraft configuration

Induced lift of a subsonic, three fan, lift/cruise, V/STOL aircraft configuration was investigated using scale modes of a multimission aircraft whose design incorporates a nose mounted lift fan and two lift/cruise units located over the wing. Configuration effects were assessed for lift improvement devices, lift/cruise nozzle rails, nozzle perimeter plates, and alternate nose fan exit hubs. Tests were conducted at four model heights (H/D = 0.95, 1.53, 3.06 and 6.45, where D is the average nozzle exit diameter equal to 0.997 m.) Results are presented and discussed.

Schuster, E. P.↗
NASA NTRS1980

Recent research on V/STOL test limits at the University of Washington aeronautical laboratory

The occurence of flow breakdown during the wind tunnel testing of a powered V/STOL aircraft was studied. Flow breakdown is the low forward speed test limit in a solid wall wind tunnel and is characterized by a vortex which forms on the floor and walls of the wind tunnel thereby failing to simulate free air conditions. The flow is caused by the interaction of the model wake and tunnel boundary layer and affects the model's aerodynamic characteristics in such fashion as to negate their reliability as correctable wind tunnel data. The low speed test limit was examined using a model that possessed a discretely concentrated powered lift system using a pair of lift jets. The system design is discussed and the tests and results which show that flow breakdown occurs at a velocity ratio of approximately 0.20 are reported.

Shindo, S.↗
NASA NTRS1980

Low speed test of the aft inlet designed for a tandem fan V/STOL nacelle

An approximately .25 scale model of a Tandem Fan nacelle designed for a Type A V/STOL aircraft configuration was tested in a 10-by-10 foot wind tunnel. A 12 inch, tip driven, turbofan simulator was used to provide the suction source for the aft fan inlet. The front fan inlet was faired over for this test entry. Model variables consisted of a long aft inlet cowl, a short aft inlet cowl, a shaft simulator, blow-in door passages and diffuser vortex generators. Inlet pressure recovery, distortion, inlet angle of attack separation limits were evaluated at tunnel velocities from 0 to 240 knots, angles of attack from -10 to 40 degrees and inlet flow rates representative of throat Mach numbers of 0.1 to 0.6. High inlet performance and stable operation was verified at all design forward speed and angle of attack conditions. The short aft inlet configuration provided exceptionally high pressure recovery except at the highest combination of angle of attack and forward speed. The flow quality at the fan face was somewhat degraded by the addition of blow-in door passages to the long aft inlet configuration due to the pressure disturbances generated by the flow entering the diffuser through the auxiliary air passages.

Rhoades, W. W.↗
NASA NTRS1980

Preliminary study of VTO thrust requirements for a V/STOL aircraft with lift plus lift/cruise propulsion

A preliminary assessment was made of the VTO thrust requirements for a supersonic (Type B) aircraft with a Lift plus Lift/Cruise propulsion system. A baseline aircraft with a takeoff gross weight (TOGW) of 13 608 kg (30,000 lb) was assumed. Pitch, roll, and yaw control thrusts (i.e., the thrusts needed for aircraft attitude control in the flight hover mode) were estimated based on a specified set of maneuver acceleration requirements for V/STOL aircraft. Other effects (such as installation losses, suckdown, reingestion, etc.), which add to the thrust requirements for VTO were also estimated. For the baseline aircraft, the excess thrust required for attitude control of the aircraft during VTO and flight hover was estimated to range from 36.9 to 50.9 percent of the TOGW. It was concluded that the total thrust requirements for the aircraft/propulsion system are large and significant. In order to achieve the performance expected of this aircraft/propulsion system, reductions must be made in the excess thrust requirements.

Turney, G. E.↗
NASA NTRS1980

Phase 1 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Test results are presented for a large scale, external augmentor V/STOL model in a 40 ft by 80 ft wind tunnel. The model was powered by a GE J97 engine and featured longitudinal ejectors alongside and external to the fuselage together with an augmentor flap on the low aspect ratio, double-delta wing. A static thrust augmentation ratio of 1.60 was measured for the fuselage augmentor at a nozzle pressure ratio of 3.0 and a nozzle exhaust gas temperature of 700 C. At forward speed the model showed a strong positive lift interference due to the augmentor flap, and a marked absence of negative lift interference due to the fuselage augmentor jet system. The nose-up moment of the fuselage augmentor inlet flow was approximately cancelled by a 60 deg deflection of the augmentor flap. An assessment of the thrust and drag components to allow the prediction of transition performance of aircraft designs based on the present conceptual model was made. Lateral tests showed strong but well ordered effects of power.

Garland, D. B.↗
NASA NTRS1980

Phase 2 and 3 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Static and forward speed tests were made in a 40 multiplied by 80 foot wind tunnel of a large-scale, ejector-powered V/STOL aircraft model. Modifications were made to the model following earlier tests primarily to improve longitudinal acceleration capability during transition from hovering to wingborne flight. A rearward deflection of the fuselage augmentor thrust vector was shown to be beneficial in this regard. Other augmentor modifications were tested, notably the removal of both endplates, which improved acceleration performance at the higher transition speeds. The model tests again demonstrated minimal interference of the fuselage augmentor on aerodynamic lift. A flapped canard surface also showed negligible influence on the performance of the wing and of the fuselage augmentor.

Garland, D. B.↗
NASA NTRS1980

VASCOMP 2. The V/STOL aircraft sizing and performance computer program. Volume 6: User's manual, revision 3

This report describes the use of the V/STOL Aircraft Sizing and Performance Computer Program (VASCOMP II). The program is useful in performing aircraft parametric studies in a quick and cost efficient manner. Problem formulation and data development were performed by the Boeing Vertol Company and reflects the present preliminary design technology. The computer program, written in FORTRAN IV, has a broad range of input parameters, to enable investigation of a wide variety of aircraft. User oriented features of the program include minimized input requirements, diagnostic capabilities, and various options for program flexibility.

Schoen, A. H.↗
NASA NTRS1980

Large scale model tests of a new technology V/STOL concept

An ejector design concept for V/STOL aircraft, featuring a double-delta configuration with two large chordwise ejector slots adjacent to the fuselage side and a tailplane or canard for longitudinal control is examined. Large scale model tests of the concept have shown that ejector systems are capable of significant thrust augmentation at realistic supply pressures and temperatures, so that power plant size and weight can be reduced accordingly. A thrust augmentation of at least 1.75 can be achieved for the isolated ejector, not making allowance for duct and nozzle losses. Substantial reductions in velocity, temperature and noise of the lifting jet are assured due to mixing within the ejector - this lessens the severity of ground erosion and the thrust loss associated with reingestion. Consideration is also given to the effect of ground proximity, longitudinal aerodynamic characteristics, transition performance, and lateral stability.

Whittley, D. C.↗
NASA NTRS1980

Experimental aerodynamic characteristics of two V/STOL fighter/attack aircraft configurations at Mach numbers from 0.4 to 1.4

A wind tunnel test was conducted to measure the aerodynamic characteristics of two horizontal attitude takeoff and landing V/STOL fighter/attack aircraft concepts. In one concept, a jet diffuser ejector was used for the vertical lift system; the other used a remote augmentation lift system (RALS). Wind tunnel tests to investigate the aerodynamic uncertainties and to establish a data base for these types of concepts were conducted over a Mach number range from 0.2 to 2.0. The present report covers tests, conducted in the 11 foot transonic wind tunnel, for Mach numbers from 0.4 to 1.4. Detailed effects of varying the angle of attack (up to 27 deg), angle of sideslip (-4 deg to +8 deg), Mach number, Reynolds number, and configuration buildup were investigated. In addition, the effects of wing trailing edge flap deflections, canard incidence, and vertical tail deflections were explored. Variable canard longitudinal location and different shapes of the inboard nacelle body strakes were also investigated.

Nelms, W. P.↗
NASA NTRS1981

Historical overview of V/STOL aircraft technology

The requirements for satisfactory characteristics in several key technology areas are discussed and a review is made of various V/STOL aircraft for the purpose of assessing the success or failure of each design in meeting design requirements. Special operating techniques were developed to help circumvent deficiencies. For the most part performance and handling qualities limitations restricted operational evaluations. Flight operations emphasized the need for good STOL performance, good handling qualities, and stability and control augmentation. The majority of aircraft suffered adverse ground effects.

Anderson, S. B.↗
NASA NTRS1981

Experimental investigations on the V/STOL tunnel at NASA/Langley Research Center

The flow characteristics of the V/STOL tunnel were investigated. The results show an interaction between tunnel components. The flow around the tunnel circuit gradually deteriorated with increasing distance from the testing area. The flow in the first diffuser was still satisfactory at the beginning of the circuit, while at the end of the circuit, the flow approaching the contraction became entirely unsatisfactory. Deterioration of flow was due largely to turning the stream around the corners, with the resulting flow distortion affecting the diffusers downstream. The large end of the last diffuser stalled on one side and nearly stalled the flow at the tip of the fan. It was found that these adverse flow characteristics reduce the flow quality and the efficiency of the tunnel.

Barna, P. S.↗