Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING MACHINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Diffusion welding of MA 6000 and a conventional nickel-base superalloy

A feasibility study of diffusion welding the oxide dispersion strengthened (ODS) alloy MA 6000 to itself and to conventional Ni-base superalloy Udimet 700 was conducted. Butt joints between MA 6000 pieces and lap joints between Udimet 700 and the ODS alloy were produced by hot pressing for 1.25 hr at temperatures ranging from 1000 to 1200 C (1832-2192 F) in vacuum. Following pressing, all weldments were heat treated and machined into mechanical property test specimens. While three different combinations of recrystallized and unrecrystallized MA 6000 butt joints were produced, the unrecrystallized to unrecrystallized joint was most successful as determined by mechanical properties and microstructural examination. Failure to weld the recrystallized material probably related to a lack of adequate deformation at the weld interface. While recrystallized MA 6000 could be diffusion welded to Udimet 700 in places, complete welding over the entire lap joint was not achieved, again due to the lack of sufficient deformation at the faying surfaces. Several methods are proposed to promote the intimate contact necessary for diffusion welding MA 6000 to itself and to superalloys.

Moore, T. J.↗

Joining AA7099 to Ni-Cr-Mo Steel using Friction Stir Dovetailing

Friction stir dovetailing (FSD) was used to join 0.5 inch (12.7 mm) AA7099 to 0.5 inch (12.7 mm) Ni-Cr-Mo steel in a lap configuration. Two new FSD approaches are reported that significantly reduce zinc embrittlement of Fe-Al intermetallic compounds (IMCs) which form during conventional friction stir welding (FSW). The first method uses the general FSD approach where a custom designed tool is employed to extrude the AA7099 into the pre-machined dovetail groove of underlying steel by forming mechanical interlocking and metallurgical bonding simultaneously. The second method uses a two-step approach where FSD of AA6061 is first used to form a silicon-rich Fe-Al IMC within the dovetail groove. AA7099 plate is then joined to the AA6061 within the dovetail using conventional FSW. A discussion of the new FSD technique, joint configurations, and process parameters are provided along with joint microstructural analyses and mechanical performance.

Friction stir dovetailing, FSD, AA7099, AA6061, ro↗

Method of producing a plug-type heat flux gauge

A method of making a plug-type heat flux gauge in a material specimen in which a thermoplug is integrally formed in the specimen is disclosed. The thermoplug and concentric annulus are formed in the material specimen by electrical discharge machining and trepanning procedures. The thermoplug is surrounded by a concentric annulus through which thermocouple wires are routed. The end of each thermocouple wire is welded to the thermoplug, with each thermocouple wire welded at a different location along the length of the thermoplug.

Liebert, Curt H.↗

Folded Resonant Horns for Power Ultrasonic Applications

Folded horns have been conceived as alternatives to straight horns used as resonators and strain amplifiers in power ultrasonic systems. Such systems are used for cleaning, welding, soldering, cutting, and drilling in a variety of industries. In addition, several previous NASA Tech Briefs articles have described instrumented drilling, coring, and burrowing machines that utilize combinations of sonic and ultrasonic vibrational actuation. The main advantage of a folded horn, relative to a straight horn of the same resonance frequency, is that the folded horn can be made shorter (that is, its greatest linear dimension measured from the outside can be made smaller). Alternatively, for a given length, the resonance frequency can be reduced. Hence, the folded-horn concept affords an additional degree of design freedom for reducing the length of an ultrasonic power system that includes a horn.

Sherrit, Stewart↗

Modelling Sawing of Metal Tubes Through FEM Simulation

The paper presents the development of a numerical model of the sawing process of AISI 304 thin tubes, which is cut through a circular blade with alternating roughing and finishing teeth. The numerical simulation environment is the three-dimensional FEM software Deform v.10.1. The teeth actual trajectories were determined by a blade kinematics analysis developed in Matlab. Due to the manufacturing rolling steps and subsequent welding stage, the tube material is characterized by a gradient of properties along its thickness. Consequently, a simplified cutting test was set up and carried out in order to identify the values of relevant material parameters to be used in the numerical model. The dedicated test was the Orthogonal Tube Cutting test (OTC), which was performed on an instrumented lathe. The proposed numerical model was validated by comparing numerical results and experimental data obtained from sawing tests carried out on an industrial machine. The following outputs were compared: the cutting force, the chip thickness, and the chip contact area.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Extremely Lightweight Optical Structures for Rapid Deployment

The structures that surround and support optical components play a key role in the performance of the overall optical system. For aerospace applications, creating an opto-mechanical structure that is athermal, lightweight, robust, and can be quickly developed from concept through to hardware is challenging. This project demonstrates a design and fabrication method for optical structures using origami-style folded, photo-etched sheetmetal pieces that are micro-welded to each other or to 3d printed metal components. Thin flexures, critical for athermal mounting of optics, can be thinner with sheetmetal than from standard machining, which leads to more compact designs and the ability to mount smaller optics. Building a structure by starting with the thinnest features, then folding that thin material to make the ''thicker'' sections is the opposite of standard machining (cutting thin features from thicker blocks). A design method is shown with mass savings of >90%, and stiffness to weight ratio improvements of 5x to 10x compared to standard methods for space systems hardware. Designs and processes for small, flexured, actively aligned systems are demonstrated as are methods for producing lightweight, structural, Miura-core sandwich panels in both flat and curved configurations. Concepts for deployable panels and component hinges are explored, as is a lens subcell with tunable piston movement with temperature change and an ultralight sunshade.

42 ENGINEERING↗

Plug-type heat flux gauge

A plug-type heat flux gauge formed in a material specimen and having a thermoplug integrally formed in the material specimen, and a method for making the same are disclosed. The thermoplug is surrounded by a concentric annulus, through which thermocouple wires are routed. The end of each thermocouple wire is welded to the thermoplug, with each thermocouple wire welded at a different location along the length of the thermoplug. The thermoplug and concentric annulus may be formed in the material specimen by electrical discharge machining and trepanning procedures.

Liebert, Curt H.↗

Cutting Tool For Shaving Weld Beads

Cutting tool proposed for use in shaving weld beads flush with adjacent surfaces of weldments. Modified version of commercial pneumatically driven rotary cutting tool, cutting wheel of which turns at speeds sufficient for machining nickel alloys, titanium, and stainless steels. Equipped with forward-mounted handle and rear-mounted skid plate to maximize control and reduce dependence on skill of technician.

Hoffman, David S.↗

NASA Tech Briefs, October 2008

Topics covered include: Control Architecture for Robotic Agent Command and Sensing; Algorithm for Wavefront Sensing Using an Extended Scene; CO2 Sensors Based on Nanocrystalline SnO2 Doped with CuO; Improved Airborne System for Sensing Wildfires; VHF Wide-Band, Dual-Polarization Microstrip-Patch Antenna; Onboard Data Processor for Change-Detection Radar Imaging; Using LDPC Code Constraints to Aid Recovery of Symbol Timing; System for Measuring Flexing of a Large Spaceborne Structure; Integrated Formation Optical Communication and Estimation System; Making Superconducting Welds between Superconducting Wires; Method for Thermal Spraying of Coatings Using Resonant-Pulsed Combustion; Coating Reduces Ice Adhesion; Hybrid Multifoil Aerogel Thermal Insulation; SHINE Virtual Machine Model for In-flight Updates of Critical Mission Software; Mars Image Collection Mosaic Builder; Providing Internet Access to High-Resolution Mars Images; Providing Internet Access to High-Resolution Lunar Images; Expressions Module for the Satellite Orbit Analysis Program Virtual Satellite; Small-Body Extensions for the Satellite Orbit Analysis Program (SOAP); Scripting Module for the Satellite Orbit Analysis Program (SOAP); XML-Based SHINE Knowledge Base Interchange Language; Core Technical Capability Laboratory Management System; MRO SOW Daily Script; Tool for Inspecting Alignment of Twinaxial Connectors; An ATP System for Deep-Space Optical Communication; Polar Traverse Rover Instrument; Expert System Control of Plant Growth in an Enclosed Space; Detecting Phycocyanin-Pigmented Microbes in Reflected Light; DMAC and NMP as Electrolyte Additives for Li-Ion Cells; Mass Spectrometer Containing Multiple Fixed Collectors; Waveguide Harmonic Generator for the SIM; Whispering Gallery Mode Resonator with Orthogonally Reconfigurable Filter Function; Stable Calibration of Raman Lidar Water-Vapor Measurements; Bimaterial Thermal Compensators for WGM Resonators; Root Source Analysis/ValuStream[Trade Mark] - A Methodology for Identifying and Managing Risks; Ensemble: an Architecture for Mission-Operations Software; Object Recognition Using Feature-and Color-Based Methods; On-Orbit Multi-Field Wavefront Control with a Kalman Filter; and The Interplanetary Overlay Networking Protocol Accelerator.

Source record↗

Tool for Two Types of Friction Stir Welding

A tool that would be useable in both conventional and self-reacting friction stir welding (FSW) has been proposed. The tool would embody both a prior tooling concept for self-reacting FSW and an auto-adjustable pin-tool (APT) capability developed previously as an augmentation for conventional FSW. Some definitions of terms are prerequisite to a meaningful description of the proposed tool. In conventional FSW, depicted in Figure 1, one uses a tool that includes (1) a rotating shoulder on top (or front) of the workpiece and (2) a rotating pin that protrudes from the shoulder into the depth of the workpiece. The main axial force exerted by the tool on the workpiece is reacted through a ridged backing anvil under (behind) the workpiece. When conventional FSW is augmented with an APT capability, the depth of penetration of the pin into the workpiece is varied in real time by a position- or force-control system that extends or retracts the pin as needed to obtain the desired effect. In self-reacting (also known as self-reacted) friction stir welding (SR-FSW), there are two rotating shoulders: one on top (or front) and one on the bottom (or back) of the workpiece. In this case, a threaded shaft protrudes from the tip of the pin to beyond the back surface of the workpiece. The back shoulder is held axially in place against tension by a nut on the threaded shaft. The main axial force exerted on the workpiece by the tool and front shoulder is reacted through the back shoulder and the threaded shaft, back into the FSW machine head, so that a backing anvil is no longer needed. A key transmits torque between the bottom shoulder and the threaded shaft, so that the bottom shoulder rotates with the shaft. A tool for SRFSW embodying this concept was reported in "Mechanism for Self-Reacted Friction Stir Welding" (MFS-31914), NASA Tech Briefs, Vol. 28, No. 10 (October 2004), page 53. In its outward appearance, the proposed tool (see Figure 2) would fit the above description of an SR-FSW tool. In this case, the FSW machine would have an APT capability and the pin would be modified to accept a bottom shoulder. The APT capability could be used to vary the distance between the front and back shoulders in real time to accommodate process and workpiece-thickness variations. The tool could readily be converted to a conventional FSW tool, with or without APT capability, by simply replacing the modified pin with a conventional FSW pin.

Carter, Robert↗

Upgrade of the LHC magnet interconnections thermal shielding

The about 1700 interconnections (ICs) between the Large Hadron Collider (LHC) superconducting magnets include thermal shielding at 50-75 K, providing continuity to the thermal shielding of the magnet cryostats to reduce the overall radiation heat loads to the 1.9 K helium bath of the magnets. The IC shield, made of aluminum, is conduction-cooled via a welded bridge to the thermal shield of the adjacent magnets which is actively cooled. TIG welding of these bridges made in the LHC tunnel at installation of the magnets induced a considerable risk of fire hazard due to the proximity of the multi-layer insulation of the magnet shields. A fire incident occurred in one of the machine sectors during machine installation, but fortunately with limited consequences thanks to prompt intervention of the operators. LHC is now undergoing a 2 years technical stop during which all magnet's ICs will have to be opened to consolidate the magnet electrical connections. The IC thermal shields will therefore have to be removed and re-installed after the work is completed. In order to eliminate the risk of fire hazard when re-welding, it has been decided to review the design of the IC shields, by replacing the welded bridges with a mechanical clamping which also preserves its thermal function. An additional advantage of this new solution is the ease in dismantling for maintenance, and eliminating weld-grinding operations at removal needing radioprotection measures because of material activation after long-term operation of the LHC. This paper describes the new design of the IC shields and in particular the theoretical and experimental validation of its thermal performance. Furthermore a status report of the on-going upgrade work in the LHC is given.

43 PARTICLE ACCELERATORS↗

Machine Learning Enhanced Development of Functionally Graded Materials Enabled by Directed Energy Deposition

The ability to functionally grade materials provides designers with a new dimension of design flexibility that can be leveraged to improve functionality, reduce cost, or improve efficiency in a wide range of applications. This program was specifically focused on FGMs for hot and harsh gas path environments. These environments are common for the hot sections of jet engines and gas turbines, where parts undergo high temperature and mechanical loads in a corrosive environment. Expensive high γ' strengthened Ni superalloys such as René 41 (R41) and René 80 (R80) are generally used exclusively for a whole part, although only a section of the part demands such superalloys. To minimize cost, low/no γ' strengthened Ni superalloys such as Inconel 718 (INC718) could be used at less-demanding sections of the part could be welded to the high γ' strengthened Ni superalloys. However, the welding typically is a failure site due to the low durability at the welding interface. Functionally grading provides a welding alternative that can allow cost reduction without sacrificing mechanical performance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Co-extrusion of Discontinuously, Non-centric Steel-reinforced Aluminum

The process of manufacturing discontinuously non-centric steel reinforced aluminum by means of co-extrusion has been examined. By this process semi-finished reinforced profiles can be fabricated for further treatment through forging techniques. Therefore, steel reinforcement elements consisting of E295GC were inserted into conventional aluminum billets and co-extruded into two different solid profiles; a rectangle one by an extrusion ratio of 10.1:1 and a round one by 4.8:1. The used aluminum alloy is EN AW-6060. The billet temperature as well as the ram speed were varied to investigate their influence on the position of the reinforcement elements inside the strand. The measurement was done by a video measurement system, called Optomess A250, after milling off the strand. The distances between the elements in longitudinal direction were nearly constant, apart from the rear part of the strand. The same was observed for the distance of the steel elements to the profile edge. This due to the inhomogeneous material flow in the transverse weld, related to the billet-to-billet extrusion. The rotation of the reinforcement elements occurs because the elements flow nearby the shear zone. Further, micrographs were made to investigate the embedding situation and the grain size distribution. The embedding of the reinforcement elements were good in the solid round profile, but in the rectangle profile were found some kind of air pocket. The grain size of the aluminum alloy close to the steel elements is much smaller than in the other parts of the solid round profile.

36 MATERIALS SCIENCE↗

Automatic arc welding of propulsion system tubing in close proximity to sensitive electronic devices

The planned final assembly of the Galileo spacecraft propulsion system tubing, which involves welding in close proximity to sensitive electronics, raised significant concerns about the effects of electromagnetic coupling of weld energy on CMOS and other sensitive integrated circuits. A test program was established to assess the potential of an orbital arc welder and an RF-induction brazing machine to damage sensitive electronic equipment. Test parameters were varied to assess the effectiveness of typical transient suppression practices such as grounding, bonding, and shielding. A technique was developed to calibrate the hazard levels at the victim-circuit location; this technique is described along with the results and conclusions of the test program.

Lumsden, J. M.↗

Cryogenic Treatment of Al-Li Alloys for Improved Weldability, Repairability, and Reduction of Residual Stresses

Service performance has shown that cryogenic treatment of some metals provides improved strength, fatigue life, and wear resistance to the processed material. Effects such as these were initially discovered by NASA engineers while evaluating spacecraft that had returned from the cold vacuum of space. Factors such as high cost, poor repairability, and poor machinability are currently prohibitive for wide range use of some aerospace aluminum alloys. Application of a cryogenic treatment process to these alloys is expected provide improvements in weldability and weld properties coupled with a reduction in repairs resulting in a significant reduction in the cost to manufacture and life cycle cost of aerospace hardware. The primary purpose of this effort was to evaluate the effects of deep cryogenic treatment of some aluminum alloy plate products, welds, and weld repairs, and optimize a process for the treatment of these materials. The optimized process is being evaluated for improvements in properties of plate and welds, improvements in weldability and repairability of treated materials, and as an alternative technique for the reduction of residual stresses in repaired welds. This paper will present the results of testing and evaluation conducted in this effort. These results will include assessments of changes in strength, toughness, stress corrosion susceptability, weldability, repairability, and reduction in residual stresses of repaired welds.

Malone, Tina W.↗

The Repair Maintenance and Fabrication Facility in the Common Habitat Architecture

The Common Habitat Architecture seeks to increase the habitability of long-duration human spaceflight systems. A key aspect of this is vehicle survivability. Missions beyond low Earth orbit need onboard capabilities for Repair, Maintenance, And Fabrication (RMAF) to overcome potential contingency scenarios. Strategies employed in historic human spaceflight such as redundancy management, reliability, sparing, orbital replacement units, and aborts may be insufficient by themselves. Based on subject matter input, a list of 53 critical failures defining a set of incidents that can render a key spacecraft subsystem inoperable were generated. A subsequent analysis found that a robust in-space RMAF system capable of performing 14 key functions can potentially repair a subsystem plagued by any of these failures. An ancillary benefit is this capability may provide psychological benefits to the crew, by enabling greater self-sufficiency in earth-independent problem solving. A basic RMAF facility has been defined for the Common Habitat, consisting of five workstations. A work bench and computer workstation provide a multipurpose horizontal work surface, computing interface, and tools storage. A CNC machining center provides a subtractive manufacturing capability for metals and plastics. A multi-material 3D printing facility provides additive manufacturing capabilities for plastic, metals, and printed electronics. A welding facility is used for joining metal components where a higher strength is needed than can be achieved with fasteners or adhesives. A glovebox facility is used to perform work that is too hazardous for any of the other workstations. This may include hardware brought in from outside the spacecraft that could potentially contaminate the cabin environment. Forward work includes considering the accommodation of additional manufacturing processes not modeled in the current system, assessing the ability of systems to operate in partial gravity and microgravity environments, incorporation of the system into the Common Habitat Computer Aided Design (CAD) model, bottoms-up mass estimating, and a crew time analysis.

Habitat↗

Friction Stir Welded Aluminum-Lithium (Al-Li) 2050 Blanks for Spin Forming

Spin forming is a metalworking process used to produce axially-symmetric parts by the application of lateral pressure from a forming tool to a circular blank mounted on a revolving, heated mandrel. This process enables production of cones, domes, or caps that can incorporate features such as flat bulkheads. Friction stir welded (FSW) Al-Li 2195 blanks have been spin formed for single-piece, launch vehicle domes up to 5 m in diameter. Al-Li 2050 plate has the advantage of availability up to 165 mm thick,whereas 2195 plate is traditionally only available up to 57 mm thick. Increased plate thickness enables greater design flexibility for machining of taller structural elements, such as stiffeners. However, 2050 is only available in plate widths up to ~3.9 m. This study demonstrated the capability of making custom 2050 blanks for spin forming large (>7.8 m in diameter), single-piece, light-weight flight articles (e.g., lunar habitats and landers) by FSW two (or more) plates together. Spin forming of welded 2050 blanks has not been attempted before this investigation. The objective was to evaluate the mechanical properties of 2050 parent material and FSW regions after spin forming and subsequent T6 heat treatment. A 3 m diameter x 38 mm thick 2050 blank was fabricated from two 1.5 m wide pieces by FSW and subsequently spin formed into a cone article. Additionally, three 1.2 m diameter x 8.1 mm thick 2050 blanks were produced by FSW and spin formed into subscale cone articles with varying strain input. Mechanical properties are reported for spin formed 2050-T6 parent material and FSW regions on the articles. Abnormal grain growth (AGG) in the FSW during heat treatment was expected based on prior experience with 2195. Implementation of an AGG suppression strategy during heat treatment reduced AGG in the FSW regions and improved ductility.

Spin forming↗

Ultrasonic Phased Array Evaluation of Control Rod Drive Mechanism (CRDM) Nozzle Interference Fit and Weld Region

Ultrasonic phased array data were collected on a removed-from-service CRDM nozzle specimen to assess a previously reported leak path. First a mock-up CRDM specimen was evaluated that contained two 0.076-mm (3.0-mil) interference fit regions formed from an actual Inconel CRDM tube and two 152.4-mm (6.0-in.) thick carbon steel blocks. One interference fit region has a series of precision crafted electric discharge machining (EDM) notches at various lengths, widths, depths, and spatial separations for establishing probe sensitivity, resolution and calibration. The other interference fit has zones of boric acid (crystal form) spaced periodically between the tube and block to represent an actively leaking CRDM nozzle assembly in the field. Ultrasonic phased-array evaluations were conducted using an immersion 8-element annular 5.0-MHz probe from the tube inner diameter (ID). A variety of focal laws were employed to evaluate the interference fit regions and J grove weld, where applicable. Responses from the mock-up specimen were evaluated to determine detection limits and characterization ability as well as contrast the ultrasonic response differences with the presence of boric acid in the fit region. Nozzle 63, from the North Anna Unit-2 nuclear power plant, was evaluated to assess leakage path(s) and was destructively dismantled to allow a visual verification of the leak path(s).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗