Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, DELTA - STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Heat-Transfer Measurements at a Mach Number of 4.95 on Two 60 deg Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 deg and 45 deg

An experimental investigation was conducted to evaluate the heat-transfer characteristics of two 60 deg swept delta wings with cylindrical leading edges of 0.25-inch radii and dihedral angles of 0 deg and 45 deg. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. The The test-section unit Reynolds number was varied from 1.95 x 10(exp 6) to 12.24 x 10(exp 6) per foot. The results of the investigation indicated that, in a plane normal to the leading edge, the laminar-flow heat-transfer distribution was in good agreement with two-dimensional blunt-body theory. The stagnation-line heat-transfer level could be predicted from two-dimensional blunt-body theory provided the stagnation-line heat-transfer coefficient was assumed to vary as the cosine of the effective sweep. A comparison of the heating rates to the 0 deg dihedral wing (planform sweep of 60 deg) and the 45 deg dihedral wing (planform sweep of 69.3 deg) with equal panel sweep and panel area indicated that the stagnation-line heat-transfer coefficient for the 45 deg dihedral wing could be as much as 40 percent less than the stagnation-line heat-transfer coefficient for the 0 deg dihedral wing at both equal angles of attack and equal lifts. The laminar-flow heat-transfer rate to both wings outside the vicinity of the stagnation line was essentially equal.

Stainback, P. Calvin↗
NASA NTRS2005

Pressure-Sensitive Paint Investigation of Double-Delta Wing Vortex Flow Manipulation

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the effect of wing fillets on the global vortex-induced surface static pressure field about a sharp leading-edge 76 deg/40 deg double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 30 degrees using an in-situ method featuring the simultaneous acquisition of electronically-scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M = 0.50 to 0.85 but increased to several percent at M = 0.95 and 1.20. The PSP pressure distributions and pseudo-colored planform view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having a parabolic or diamond planform situated at the strake-wing intersection were designed to manipulate the vortical flows by, respectively, removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗
NASA NTRS2006

Wind Tunnel Application of a Pressure-Sensitive Paint Technique to a Double Delta Wing Model at Subsonic and Transonic Speeds

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to study the effect of wing fillets on the global vortex induced surface static pressure field about a sharp leading-edge 76 deg./40 deg. double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M(sub infinity) = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 20 degrees using an insitu method featuring the simultaneous acquisition of electronically scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M(sub infinity) = 0.50 to 0.85 but increased to several percent at M(sub infinity) =0.95 and 1.20. The PSP pressure distributions and pseudo-colored, planform-view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having parabolic or diamond planforms situated at the strake-wing intersection were respectively designed to manipulate the vortical flows by removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗
NASA NTRS1971

An experimental study of the hypersonic aerodynamics of delta wings.

Results of aerodynamic balance and pressure measurements carried out in a hypersonic gun tunnel (at a free-stream Mach number of 8.2 and a Reynolds number of 800,000) on delta wings having sharp leading edges swept at 70 and 76 deg. The experimental force and pressure coefficients and shock angles are discussed in relation to simple prediction methods. Some transition data are also included.

Rao, D. M.↗
NASA NTRS1989

A flow visualization and aerodynamic force data evaluation of spanwise blowing on full and half span delta wings

A wind-tunnel investigation has been performed to quantify the effects of a jet on the leading-edge vortices generated by a 70-deg-sweep sharp-edged delta wing at low Reynolds numbers. Efforts were made ot optimize the jet nozzle position with respect to maximum lift increments. Both half-span force-balance testing and half- and full-span flow visualization tests were conducted. Two angles of attack were investigated, 30 and 35 deg, at Reynolds numbers of 150,000 and 200,000. Aerodynamic enhancement, including lift and drag gains of about 20 and 17 percent respectively, were measured. Results indicate an optimum jet nozzle location to be close to the leading edge, tangent to the upper wing surface, and in a direction aligned parallel to the leading edge. Nozzle interference effects, especially near the apex, were not negligible.

Visser, K. D.↗
NASA NTRS1977

Effects of roughness size on the position of boundary-layer transition and on the aerodynamic characteristics of a 55 deg. swept delta wing at supersonic speeds

An experimental investigation was conducted to determine the effects of roughness size on the position of boundary layer transition and on the aerodynamic characteristics of a 55 deg swept delta wing model. Results are presented and discussed for wind tunnel tests conducted at free stream Mach numbers from 1.50 to 4.63, Reynolds numbers per meter from 3,300,000 to 1.6 x 10 to the 7th power, angles of attack from -8 to 16 deg, and roughness sizes ranging from 0.027 cm sand grit to 0.127 cm high cylinders. Comparisons were made with existing flat plate data. An approximate method was derived for predicting the drag of roughness elements used in boundary layer trips.

Stallings, R. L., Jr.↗
NASA NTRS1983

Large-scale wind-tunnel investigation of a close-coupled canard-delta-wing fighter model through high angles of attack

Data obtained through very high angles of attack from a large-scale, subsonic wind-tunnel test of a close-coupled canard-delta-wing fighter model are analyzed. The canard delays wing leading-edge vortex breakdown, even for angles of attack at which the canard is completely stalled. A vortex-lattice method was applied which gave good predictions of lift and pitching moment up to an angle of attack of about 20 deg, where vortex-breakdown effects on performance become significant. Pitch-control inputs generally retain full effectiveness up to the angle of attack of maximum lift, beyond which, effectiveness drops off rapidly. A high-angle-of-attack prediction method gives good estimates of lift and drag for the completely stalled aircraft. Roll asymmetry observed at zero sideslip is apparently caused by an asymmetry in the model support structure.

Stoll, F.↗
NASA NTRS1954

Investigation at transonic speeds of the lateral-control and hinge-moment characteristics of a flap-type spoiler aileron on a 60 degree delta wing

This paper present results of an investigation of the lateral-control and hinge-moment characteristics of a 0.67 semispan flap-type spoiler aileron on a semispan thin 60 degree delta wing at transonic speeds by the reflection-plane technique. The spoiler-aileron had a constant chord of 10.29 percent mean aerodynamic chord and was hinged at the 81.9-percent-wing-root-chord station. Tests were made with the spoiler aileron slot open, partially closed, and closed. Incremental rolling-moment coefficients were obtained through a Mach number range of 0.62 to 1.08. Results indicated reasonably linear variations of rolling-moment and hinge-moment coefficients with spoiler projection except at spoiler projections of less than -2 percent mean aerodynamic chord and angles of attack greater than 12 degrees with results generally independent of slot geometry.

Wiley, Harleth G↗
NASA NTRS1961

Transonic Loads Characteristics of a 3-Percent-Thick 60 deg Delta-Wing-Body

An investigation has been made in the Langley 16-foot transonic tunnel to determine the aerodynamic loading characteristics of a 3-percent-thick, aspect-ratio - 2.06, 60 deg delta-wing-body combination. The Mach number range was from 0.80 t o 1.05 and the average Reynolds number based on wing mean aerodynamic chord was 10 x 10(exp 6). The angle-of-attack range was from 0 deg to 26 deg but was limited at the highest Mach numbers by tunnel drive power. Pressure distributions, spanwise loadings, integrated wing coefficients, and tabulated pressure coefficients are presented for the range of Mach numbers and angles of attack. The results indicate that a free leading-edge separation vortex is the dominant flow-field phenomenon at all Mach numbers and that, consequently, there are only slight changes in the spanwise loadings with Mach number. There is a slight outboard shift in center of pressure with an increase in Mach number. The chord-wise position of the center of pressure varies from 46 t o 55 percent of the mean aerodynamic chord when the Mach number i s increased from 0.80 to l.05.

Swihart, John M.↗
NASA NTRS1993

Supersonic vortex breakdown over a delta wing in transonic flow

The effects of freestream Mach number and angle of attack on the leading-edge vortex breakdown due to the terminating shock on a 65-degree, sharp-edged, cropped delta wing are investigated computationally, using the time-accurate solution of the laminar unsteady compressible full Navier-Stokes equations with the implicit upwind flux-difference splitting, finite-volume scheme. A fine O-H grid consisting of 125 x 85 x 84 points in the wrap-around, normal, and axial directions, respectively, is used for all the flow cases. Keeping the Reynolds number fixed at 3.23 x 10 exp 6, the Mach number is varied from 0.85 to 0.9 and the angle of attack is varied from 20 to 24 deg. The results show that, at 20-deg angle of attack, the increase of the Mach number from 0.85 to 0.9 results in moving the location of the terminating shock downstream. The results also show that, at 0.85 Mach number, the increase of the angle of attack from 20 to 24 deg results in moving the location of the terminating shock upstream. The results are in good agreement with the experimental data.

Kandil, Hamdy A.↗
NASA NTRS1973

Space shuttle: Pressure investigation of a space shuttle launch configuration consisting of a delta-wing orbiter and a swept-wing booster with canard and tip fans (M equals 0.6 to 1.3). Volume 1, part A: Booster data

Wind tunnel tests to determine the pressure distribution on a space shuttle launch configuration consisting of a delta wing orbiter and a swept wing booster with canard and tip fins were conducted. Pressure data were obtained for the combined orbiter and booster and for the booster alone at Mach numbers from 0.6 to 1.3, angles of attack from minus 8 degrees to plus 10 degrees, and sideslip angles from minus 6 degrees to plus 6 degrees. Pressure data were also obtained for the booster alone without canard at Mach numbers of 0.9 and 1.1. The pressure taps were distributed primarily over the booster upper surface and the orbiter lower surface.

Rampy, J. M.↗
NASA NTRS1975

Delta wing flutter based on doublet lattice method in NASTRAN

The subsonic doublet-lattice method (DLM) aeroelastic analysis in NASTRAN was successfully applied to produce subsonic flutter boundary data in parameter space for a large delta wing configuration. Computed flow velocity and flutter frequency values as functions of air density ratio, flow Mach number, and reduced frequency are tabulated. The relevance and the meaning of the calculated results are discussed. Several input-deck problems encountered and overcome are cited with the hope that they may be helpful to NASTRAN Rigid Format 45 users.

Jew, H.↗
NASA NTRS1993

Computation of transonic viscous flow past the NTF 65-degree Delta Wing

This project is a continuation of the work performed in the summers of 1991 and 1992, during which a 9-block structured grid for the computational domain around each of the four NTF 65-degree Delta Wing models with the sting mount were created. The objective of the project is to validate and supplement the test data on the wing models by computing the viscous flow field about the models.

Wu, Chivey↗
NASA NTRS1987

Visualization of vortex breakdown on a delta wing

An account is given of the results obtained by a flow visualization study of the roll-up, breakdown position, and spiral- or bubble-type breakdown characteristics of an 85-deg sweep, flat-plate delta wing at large angles-of-attack. The two different breakdown modes were noted to metamorphose into each other, with the bubble-type phenomenon appearing to prefer a more upstream location relative to the spiral mode. In those instances when the breakdown location was changing, the breakdown took the form of a bubble when moving forward, and spiral when moving aft.

Nelson, R. C.↗
NASA NTRS1977

Load distributions on slender delta wings having vortex flow

Results obtained through application of potential-flow theory based on a suction flow analogy for incompressible flow are compared to attached-flow theory and to experimental data acquired for sharp-edged delta wings. The error incurred in predicting structural loads on the basis of attached-flow theory is investigated. Force and moment coefficients and load distributions are used in the comparisons. The root bending moment can be estimated by assuming vortex lift concentrated at the wing leading edge. While this may entail some error at large angles of attack (owing to inboard movement of the center of vortex lift), it may furnish an upper bound in evaluating results based on other theories.

Kuhlman, J.↗
NASA NTRS1982

Lateral aerodynamics of delta wings with leading edge separation

An unsteady vortex lattice method is presented for the calculation of the aerodynamic forces acting on lifting surfaces undergoing complex three dimensional motion. For the present case the nonsymmetric motion of a slender delta wing was considered and the resulting lateral characteristics were calculated. The flow separation line was specified along the wing leading edge and the emanating vortex sheet shape and rollup was then calculated. Numerical results are presented for the combined high angle of attack and side slip condition and for the wing constant roll and coning motions.

Katz, J.↗
NASA NTRS1994

Transonic Navier-Stokes calculations about a 65 deg delta wing

A computational study has been conducted in which the CFL3D Navier-Stokes solver coupled with an algebraic and a one-equation nonequilibrium turbulence model has been used to predict the flow over a 65 degree delta wing at transonic conditions for Reynolds numbers ranging from 6 x 10(exp 6) to 120 x 10(exp 6) based on mean aerodynamic chord. Solutions obtained indicated that the computational method when used with the one-equation turbulence model predicts results that compare well with experiment for attached flow conditions. Comparisons with experimental pressure at separated conditions show that the computational method, even though primary flow-field features are predicted well, does not predict secondary flow features.

Londenberg, W. Kelly↗