Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wave modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Plasma heating by electron cyclotron wave and the temperature effects on lower hybrid current drive on EAST

This paper presents the progress in the long—pulse operation of the electron cyclotron (EC) system and the achievements in high—electron temperature plasmas by the combined EC and lower hybrid (LH) waves heating since the EC system was built in 2015. An electron temperature of up to 12 keV with a duration over 100 s was realized by the simultaneous heating of EC and LH waves at the line-averaged density ${\bar n_{\text{e}}}$ ~1.8 × 10 19 m –3 . The plasma heating effect strongly depends on the location of EC power deposition. H-mode plasmas with solely EC wave auxiliary heating have been obtained on EAST for the first time. These H-mode discharges show an enhanced confinement factor H 98(y,2) around 1.0, which is higher than the previous H-mode using LH power alone (Xu et al 2011 Nucl. Fusion 51 072001). The total heating power is very close to the threshold value for L–H transition according to the international tokamak scaling. In addition to the temperature effects inside the separatrix, higher electron temperature produced by EC wave is found to reduce the LH power loss in the scrape-off layer due to collisional absorption, which is beneficial to further increase the LH current drive efficiency. Ray-tracing/Fokker–Planck modeling results indicate that higher electron temperature can shorten the LH wave propagation on EAST in a multiple-pass regime, thus decreasing the collisional dissipation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental Investigation of Fuel Staging Effect on Modal Dynamics of Thermoacoustic Azimuthal Instabilities in a Multi-Nozzle Can Combustor

Abstract This paper analyzes the dynamics of unstable azimuthal thermoacoustic modes in a lean premixed combustor. Azimuthal modes can be decomposed into two counter rotating waves where they can either compete and potentially suppress one of them (spinning) or coexist (standing), depending on the operating conditions. This paper describes experimental results of the dynamical behaviors of these two waves. The experimental data were taken at different mass flow rates as well as different azimuthal fuel staging in a multi-nozzle can combustor. It is shown that at a low flow rate with uniform fuel distribution, the two waves have similar amplitudes, giving rise to a standing wave. However, the two amplitudes are slowly oscillating out of phase to each other, and the phase difference between the two waves also shows oscillatory behavior. For an intermediate flow rate, the dynamics show intermittency between standing and spinning waves, indicating that the system is bistable. In addition, the phase difference dramatically shifts when the mode switches between standing and spinning waves. For a high flow rate, the system stabilizes at a spinning wave most of the time. These experimental observations demonstrate that not only the amplitudes of two waves but also the phase difference plays an important role in the dynamics of azimuthal mode. For non-uniform azimuthal fuel staging, the modal dynamics exhibit only an oscillatory standing wave behavior regardless of the mass flow rate. Compared to the uniform fuel staging, however, the pressure magnitude is considerably reduced, which provides a potential strategy to mitigate and/or suppress the instabilities.

Kim, J.↗
DOE OSTI2020

Experimental and numerical studies of seismic fluid-structure interaction in a base-supported cylindrical vessel

Seismic design and qualification of advanced reactors will rely heavily on the use of verified and validated numerical models capable of capturing the interaction of the vessel, its contained fluid, and the internal equipment: fluid-structure interaction (FSI) analysis. Analytical solutions can be used for preliminary sizing and design of such vessels but their application is limited to simple geometries and boundary conditions, and small amplitude, translational (and rotational) inputs. To validate numerical models for seismic FSI analysis in finite element codes, a comprehensive set of experiments was performed on a liquid-filled cylindrical vessel, using a 6 degree-of-freedom earthquake simulator. Results in terms of sloshing frequency, damping ratio in sloshing modes, and hydrodynamic responses (wave height, hydrodynamic pressure, base shear, and base moment) for multi-directional earthquake simulator inputs are reported and compared with analytical solutions for liquid-filled vessels. The impact of seismic (base) isolation on hydrodynamic responses was studied using earthquake simulator inputs generated using a virtual isolation system. Data from the experiments are used to validate a numerical model of the fluid-filled vessel using the Arbitrary Lagrangian Eulerian (ALE) solver in the commercial finite element program LS-DYNA. Validation studies are presented for multi-directional seismic inputs, including rocking motions. Lagrangian modeling approaches using an elastic material formulation for the fluid are also investigated and their limitations and possible applications are identified. Here, the results are broadly applicable to the seismic response of base supported, liquid-filled vessels.

58 GEOSCIENCES↗
DOE OSTI2021

Recurrence analysis of friction based dry-couplant ultrasonic Lamb waves in plate-like structures

Here, in this study, the effect of friction on the generation of dry-coupled Lamb waves is experimentally investigated. Recurrence analysis is performed to analyze the complex behavior of friction based dry-coupled Lamb waves. In particular, the effect of the normal force, which is necessary for a stronger dry-coupled Lamb wave generation and the friction, on the transmission of mechanical energy and determinism characteristics of Lamb waves are investigated. The results verify that larger friction coefficient and friction force are crucial for generation and propagation of strong Lamb waves supporting the fact that the main mechanism to transfer mechanical energy using dry-couplant is friction. The sensitivity of Lamb waves to the friction coefficient, highlights the importance of designing specific pads with respect to condition of the surface. Besides, the results show that the normal force and friction coefficient can change the determinism characteristics behavior of multimode Lamb waves. Furthermore, it is shown that the determinism value is sensitive to the friction coefficient and normal force. A similar trend is observed in the determinism values and friction coefficient. In general, a smaller friction coefficient indicates smaller determinism value. Additionally, it is shown that a normal load can change the behavior of a system, as observed from recurrence plots, owing to changes in the Lamb waves trajectories in the phase-space domain. In addition, it is shown that recurrence plots enable the detection of mode transitions in multimode Lamb waves. Recurrence analysis is a complementary tool to frequency domain methods for accurate analysis of multimode Lamb waves behavior.

42 ENGINEERING↗
DOE OSTI2020

Illumination of Damage in Intact Rocks by Ultrasonic Transmission-Reflection and Digital Image Correlation

aboratory-scale experiments on intact rocks are critical to the development of physics-based fundamental understanding of various geophysical phenomena. In this work, the capability of ultrasonic wave transmission (T-mode) and reflection (R-mode) to monitor damage progression in uniaxially loaded prismatic intact rock specimens has been analyzed, as it is imperative to study the observations and document the capabilities of these techniques in a controlled environment. This study is novel in the sense that the R-mode linear ultrasonic testing (LUT) has been rarely employed in studying intact rock damage processes in a laboratory setting, with most of the studies utilizing a direct transmission (T-mode) approach or focusing on macroscopically fractured material. The two-dimensional digital image correlation (2-D DIC) full-field strain measurement approach was also used in-sync with the LUT monitoring to explicitly correlate the stress-induced damage in the specimens with the changes observed in the ultrasonic (T-mode and R-mode) signals. The results show that both the T-mode and R-mode LUT approaches are sensitive to detect the evolution of tensile and shear damage in the specimens, with the R-mode ultrasonic signals showing higher degree of sensitivity to the damage in the rocks, immediately following the initiation of damage in the rock volume.

58 GEOSCIENCES↗
DOE OSTI2023

Mesoscopic two-point collective dynamics of glass-forming liquids

The collective density–density and hydrostatic pressure–pressure correlations of glass-forming liquids are spatiotemporally mapped out using molecular dynamics simulations. It is shown that the sharp rise of structural relaxation time below the Arrhenius temperature coincides with the emergence of slow, nonhydrodynamic collective dynamics on mesoscopic scales. The observed long-range, nonhydrodynamic mode is independent of wave numbers and closely coupled to the local structural dynamics. Below the Arrhenius temperature, it dominates the slow collective dynamics on length scales immediately beyond the first structural peak in contrast to the well-known behavior at high temperatures. Furthermore, these results highlight a key connection between the qualitative change in mesoscopic two-point collective dynamics and the dynamic crossover phenomenon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Experimental determination of axion signal power of dish antennas and dielectric haloscopes using the reciprocity approach

The reciprocity approach is a powerful method to determine the expected signal power of axion haloscopes in a model-independent way. Especially for open and broadband setups like the MADMAX dielectric haloscope the sensitivity to the axion field is difficult to calibrate since they do not allow discrete eigenmode analysis and are optically too large to fully simulate. The central idea of the reciprocity approach is to measure a reflection-induced test field in the setup instead of trying to simulate the axion-induced field. In this article, the reciprocity approach is used to determine the expected signal power of a dish antenna and a minimal dielectric haloscope directly from measurements. The results match expectations from simulation but also include important systematic effects that are too difficult to simulate. In particular, the effect of antenna standing waves and higher order mode perturbations can be quantified for the first time in a dielectric haloscope.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Temperature and Strain Sensing Characteristics of a 128° YX-Cut LiNbO 3 Rayleigh-Mode SAW Sensor From Room to Cryogenic Temperatures

Accurate, passive, and wireless monitoring of cryogenic hardware is essential for high-energy physics, space propulsion, and biomedical instrumentation. Here, this study quantifies the coupled temperature-strain behavior of Rayleigh-mode surface acoustic-wave (SAW) delay-line sensors fabricated on 128° YX-cut LiNbO 3 . A nonlinear finite element (FE) model incorporating Varshni-based elastic constants, higher-order thermal expansion, and temperature-dependent piezo- and dielectric coefficients was developed and validated experimentally between 280K and 80K. Free-standing (first test condition) and bonded/wired (second test condition) devices exhibited indistinguishable thermal responses; the average temperature coefficient of delay (TCD) in the critical cryogenic range from 130K down to 80K differed by only 0.15 ppm/K (0.32%), confirming that bonding-induced stress is negligible. Over 280-80K the measured TCD was 61.77 ppm/K, while the FE model predicted an equivalent temperature coefficient of frequency (TCF) of −62.74 ppm/K with an overall coefficient of determination R2 = 0.998. In the critical cryogenic interval 130-80K the TCD fell to 47.66 ppm/K, indicating improved thermal stability at low temperature. Controlled loading (0-300 με) revealed a strain coefficient of delay (SCD) that rises from 0.53 ± 0.02 ppm/με at 300K to 1.05 ± 0.02 ppm/με at 80K. This modest sensitivity confirms that, for temperature sensing, strain is a second-order perturbation above 135K but must be compensated at deeper cryogenic levels. Overall, this work establishes a predictive multiphysics model together with repeatable wired measurements that confirm the suitability of SAW sensors for temperature and strain monitoring in extreme cryogenic environments, while also providing a baseline for future wireless implementations.

25 ENERGY STORAGE↗
DOE OSTI2023

Acoustic scattering by smooth elastic cylinders insonified by directional transceivers: Monostatic theory and experiments

A theoretical model for predicting the acoustic field scattered by an elastic cylinder that is partially insonified by a directional transceiver is proposed in the form of a simple approximate one-dimensional integral. This model accounts for spherical spreading and directivity of the incident waves and extends the formulation used in a preceding article by including effects due to oblique insonification of a long cylinder assuming negligible end-contributions. The scattered field of an infinitely long cylinder for obliquely incident plane waves and point receivers is used to approximate the apparent volume flow of cylinders partially insonified by directional transceivers. The scattered pressure that is derived using the apparent volume flow, in contrast to the previous formulation, is capable of predicting axially propagating guided wave resonances; these natural modes are excited, in addition to circumferential ones, at off-normal incident angles. The model is compared with exact numerical simulations and with previously published as well as new laboratory data. The analysis illustrates the different realistic effects associated with scattering from elastic cylinders insonified by a directional transceiver both theoretically and experimentally.

42 ENGINEERING↗
DOE OSTI2022

Transmission estimation at the quantum Cramér-Rao bound with macroscopic quantum light

The field of quantum metrology seeks to apply quantum techniques and/or resources to classical sensing approaches with the goal of enhancing the precision in the estimation of a parameter beyond what can be achieved with classical resources. Theoretically, the fundamental minimum uncertainty in the estimation of a parameter for a given probing state is bounded by the quantum Cramér-Rao bound. From a practical perspective, it is necessary to find physical measurements that can saturate this fundamental limit and to show experimentally that it is possible to perform measurements with the required precision to do so. Here we perform experiments that saturate the quantum Cramér-Rao bound for transmission estimation over a wide range of transmissions when probing the system under study with a continuous wave bright two-mode squeezed state. To properly take into account the imperfections in the generation of the quantum state, we extend our previous theoretical results to incorporate the measured properties of the generated quantum state. For our largest transmission level of 84%, we show a 62% reduction over the optimal classical protocol in the variance in transmission estimation when probing with a bright two-mode squeezed state with -8 dB of intensity-difference squeezing. Given that transmission estimation is an integral part of many sensing protocols, such as plasmonic sensing, spectroscopy, calibration of the quantum efficiency of detectors, etc., the results presented promise to have a significant impact on a number of applications in various fields of research.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Spatially Multiplexed Cluster State Generation

We demonstrate the use of spatially multimode two-mode squeezed states (TMSSs) interfered at beamsplitters to generate an arbitrarily large cluster state. A four-mode state is generated using two TMSSs, leveraging spatial modes of four-wave mixing.

Leger, Zacharie [ORNL] (ORCID:0000000179044775)↗
DOE OSTI2019

Observation of spin-polarized directive coupling of light at bound states in the continuum

Spin-polarized directive coupling of light associated with the photonic quantum spin-Hall effect (QSHE) is a nanoscale phenomenon based on strong spin–orbit interaction that has recently attracted significant attention. Herein, we discuss the experimental manifestation of QSHE intrinsic in the Bloch waves associated with a bound state in the continuum (BIC) of a dielectric photonic crystal metasurface (PhCM). We show numerically that BICs in nanoscale PhCMs have photonic spin angular momentum density transverse to the orbital momentum not only at the interfaces but also inside the confining dielectric medium. Then, we experimentally demonstrate that the fundamental Bloch waves of the BIC mode, macroscopically amplified on resonance, propagate along the symmetry axes of the PhCM obeying spin-momentum locking also at normal incidence, i.e., with no symmetry breaking. This BIC-enhanced spin-directive coupling of light may enable versatile implementations of spin-optical structures, paving the way for novel photonic spin multiplatform devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Evidence of 5 minute Oscillations from Parker Solar Probe

The Sun’s surface vibrates in characteristic 5 minute oscillations, known as p-modes, generated by sound waves trapped within the convection zone. Although these oscillations have long been hypothesized to reach into the solar wind, direct in situ evidence has remained elusive, even during previous close encounters by Parker Solar Probe (PSP). Here, we present strong in situ evidence of 5 minute oscillations in the upper solar corona, based on observations from PSP’s three closest perihelia. In two events at 9.9 solar radii (R ⊙ ), we identify statistically significant (∼6σ) 3.1–3.2 mHz peaks in the magnetic field power spectrum, each appearing as a large-amplitude, spherically polarized Alfvénic wave train lasting approximately 35 minutes. These results demonstrate that global solar oscillations can reach the solar wind.

Fast solar wind↗
DOE OSTI2021

Design and Testing of a Water-Cooled Rotating Detonation Combustor at Elevated Operating Pressures - Abstract

This is an extended abstract being submitted for consideration that briefly describes the material that will be included in the final paper. This study will detail the design and testing of a water-cooled Rotating Detonation Combustor (RDC) that permits operation for extended periods of time ensuring that the device has reach a stable operating temperature. Extended run times also provides an opportunity to consider transient behaviors that occur as a result of altering the operating conditions such as equivalence ratio. The experimental setup is also unique in that it consists of a ducted exhaust with a downstream high-temperature valve that can control the pre-combustion pressure in the RDC independent of the combustor annulus and exit geometry. This paper will examine the results from the extended operation of the water-cooled RDC over a range of both transient and steady state equivalence ratios (0.5 - 1.0), pre-combustion operating pressures (0 - 207 kPa), mass flow rates (0.42 – 0.5 kg/sec) and air inlet throat area to combustor channel area ratios (0.09 – 0.32). All tests were performed while operating on hydrogen in air at a nominal air inlet temperature of 340 – 350 K. Limited data obtained at an elevated inlet air temperature of 480 K will also be discussed. Results suggest that under certain conditions the operating mode of the detonation wave can vary as it approaches a stable operating temperature. For the RDC tested, a stable operating temperature is not achieved until approximately 8-10 seconds of run time.

Ferguson, Donald↗
DOE OSTI2022

Experimental Investigation of Interactions Between Two Closely Spaced Azimuthal Modes in a Multinozzle Can Combustor

Thermoacoustic instabilities in annular or circular combustors are often coupled with azimuthal modes. These modes can be characterized by a spin ratio (SR), which quantifies the dominant mode between two counter-rotating waves, and a phase difference between them, which is directly related to the orientation of the antinodal line. This study investigates the instability amplitudes, SR, and phase difference of two closely spaced (3% of their mean frequency), yet distinct azimuthal modes; one is the first azimuthal (1A) mode, and the other is a combination of first azimuthal and first longitudinal (1A1L) mode. Each mode itself consists of two peaks that are spaced even more closely in frequency (0.8%). Furthermore, distinct harmonics at 2× and 3× of these frequencies, presumably associated with nonlinearities, are also evident in the spectra. Each mode is bandpass filtered in spectrum to analyze them separately. For the 1A mode, the SR and phase difference exhibit a variety of behaviors—including quasi-periodic standing waves, spinning waves, and intermittency—depending on operating conditions such as thermal power and azimuthal fuel staging. Similar trends are observed for the 1A1 L mode. Moreover, there is clear coupling between the 1A and 1A1 L modes, as their SRs are almost synchronized during the quasi-periodic standing wave. This synchronization is observed in phase differences as well, but not in the instability amplitude. For spinning dominant wave conditions, the SRs of each mode have similar average values, but they fluctuate in a seemingly random fashion. For the phase difference, both average and fluctuation are not correlated. In contrast, the instability amplitudes are strongly correlated, with modulation of the 1A mode leading to that of the 1A1 L mode. Furthermore, these results clearly indicate that complex coupling occurs across closely spaced frequencies under instability conditions, coupling that must be understood in order to capture limit cycle dynamics.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Numerical simulation of the beam self-cleaning process in a multimode graded-index fibre during propagation of a pump wave and a Stokes component

A model of coupled modes is proposed, which makes it possible to describe the propagation of a pump wave and a Stokes component in a multimode graded-index fibre. A decrease in the depression in the centre of the profile of the pump wave intensity distribution as a result of the influence of Kerr effects and random linear coupling of modes is demonstrated. (paper)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Generation of waves in magnetized plasma [PowerPoint]

The presentation goes through assumptions made for the study, sections on plasma dispersion, whistler modes for RBR, excitation of plane waves with antenna, dipole vs loop antenna, verification of results, excitation of whistler waves with electron beams, assumptions for the model, distribution of current in space in general case, Fourier transform of current distribution, resonant excitation of waves, and ending with a discussion of generic debunching.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Toroidal Alfven Wave Coupling (Nonlinear Wave-Wave Interactions) on DIII-D

Connect DIII-D physics with space plasma phenomena. In this case of using the toroidal Alfvén eigenmodes and frequency-chirping Reversed-Shear Alfvén eignmodes in DIII-D, we will document how the nonlinear interactions among dipolar Kinetic Alfvén Wave eigenmodes in space plasmas may determine saturation levels of these fluctuations. We seek evidence of nonlinear energy transfer and wave-wave coupling during 3-wave interactions mediated by a much lower-frequency mode. In FY2019, we found evidence of nonlinear “wave-wave” interactions in 175 relevant shots of archival DIII-D data. Toroidal mode number was identified and spectrograms were produced from each shot’s Mirnov coil data. Bispectral analysis was performed using a preliminary version of a new user friendly code derived from a 1995 M.S. thesis at WVU. These results formed a part of a May 2019 M.S. thesis at WVU.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗